diff --git a/[refs] b/[refs] index 5967d3a8d98a..cdbe5e8202ec 100644 --- a/[refs] +++ b/[refs] @@ -1,2 +1,2 @@ --- -refs/heads/master: c76d292db9869ae73fd401e9a3fc728ed5caf0a7 +refs/heads/master: cae399880f82fdc6b0afccf42224fc2a759aa6b3 diff --git a/trunk/arch/arm/Kconfig b/trunk/arch/arm/Kconfig index 5711c8160e75..99829a2bee92 100644 --- a/trunk/arch/arm/Kconfig +++ b/trunk/arch/arm/Kconfig @@ -363,7 +363,7 @@ config ARCH_MXS bool "Freescale MXS-based" select GENERIC_CLOCKEVENTS select ARCH_REQUIRE_GPIOLIB - select CLKDEV_LOOKUP + select COMMON_CLKDEV help Support for Freescale MXS-based family of processors diff --git a/trunk/arch/arm/common/sa1111.c b/trunk/arch/arm/common/sa1111.c index d6c784e78c83..eb9796b0dab2 100644 --- a/trunk/arch/arm/common/sa1111.c +++ b/trunk/arch/arm/common/sa1111.c @@ -279,7 +279,7 @@ static int sa1111_retrigger_lowirq(struct irq_data *d) for (i = 0; i < 8; i++) { sa1111_writel(ip0 ^ mask, mapbase + SA1111_INTPOL0); sa1111_writel(ip0, mapbase + SA1111_INTPOL0); - if (sa1111_readl(mapbase + SA1111_INTSTATCLR1) & mask) + if (sa1111_readl(mapbase + SA1111_INTSTATCLR0) & mask) break; } diff --git a/trunk/arch/arm/mach-at91/Kconfig b/trunk/arch/arm/mach-at91/Kconfig index 19390231a0e9..c015b684b4fe 100644 --- a/trunk/arch/arm/mach-at91/Kconfig +++ b/trunk/arch/arm/mach-at91/Kconfig @@ -362,12 +362,6 @@ config MACH_CPU9G20 Select this if you are using a Eukrea Electromatique's CPU9G20 Board -config MACH_ACMENETUSFOXG20 - bool "Acme Systems srl FOX Board G20" - help - Select this if you are using Acme Systems - FOX Board G20 - config MACH_PORTUXG20 bool "taskit PortuxG20" help @@ -387,13 +381,6 @@ config MACH_PCONTROL_G20 Select this if you are using taskit's Stamp9G20 CPU module on this carrier board, beeing the decentralized unit of a building automation system; featuring nvram, eth-switch, iso-rs485, display, io - -config MACH_GSIA18S - bool "GS_IA18_S board" - help - This enables support for the GS_IA18_S board - produced by GeoSIG Ltd company. This is an internet accelerograph. - endif if (ARCH_AT91SAM9260 || ARCH_AT91SAM9G20) diff --git a/trunk/arch/arm/mach-at91/Makefile b/trunk/arch/arm/mach-at91/Makefile index a83835e0c185..d13add71f72a 100644 --- a/trunk/arch/arm/mach-at91/Makefile +++ b/trunk/arch/arm/mach-at91/Makefile @@ -63,11 +63,9 @@ obj-$(CONFIG_MACH_AT91SAM9RLEK) += board-sam9rlek.o # AT91SAM9G20 board-specific support obj-$(CONFIG_MACH_AT91SAM9G20EK) += board-sam9g20ek.o obj-$(CONFIG_MACH_CPU9G20) += board-cpu9krea.o -obj-$(CONFIG_MACH_ACMENETUSFOXG20) += board-foxg20.o obj-$(CONFIG_MACH_STAMP9G20) += board-stamp9g20.o obj-$(CONFIG_MACH_PORTUXG20) += board-stamp9g20.o obj-$(CONFIG_MACH_PCONTROL_G20) += board-pcontrol-g20.o board-stamp9g20.o -obj-$(CONFIG_MACH_GSIA18S) += board-gsia18s.o board-stamp9g20.o # AT91SAM9260/AT91SAM9G20 board-specific support obj-$(CONFIG_MACH_SNAPPER_9260) += board-snapper9260.o diff --git a/trunk/arch/arm/mach-at91/board-foxg20.c b/trunk/arch/arm/mach-at91/board-foxg20.c deleted file mode 100644 index dfc7dfe738e4..000000000000 --- a/trunk/arch/arm/mach-at91/board-foxg20.c +++ /dev/null @@ -1,274 +0,0 @@ -/* - * Copyright (C) 2005 SAN People - * Copyright (C) 2008 Atmel - * Copyright (C) 2010 Lee McLoughlin - lee@lmmrtech.com - * Copyright (C) 2010 Sergio Tanzilli - tanzilli@acmesystems.it - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -#include -#include -#include -#include - -#include -#include -#include - -#include -#include - -#include "sam9_smc.h" -#include "generic.h" - -/* - * The FOX Board G20 hardware comes as the "Netus G20" board with - * just the cpu, ram, dataflash and two header connectors. - * This is plugged into the FOX Board which provides the ethernet, - * usb, rtc, leds, switch, ... - * - * For more info visit: http://www.acmesystems.it/foxg20 - */ - - -static void __init foxg20_map_io(void) -{ - /* Initialize processor: 18.432 MHz crystal */ - at91sam9260_initialize(18432000); - - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - at91_register_uart(AT91SAM9260_ID_US0, 1, - ATMEL_UART_CTS - | ATMEL_UART_RTS - | ATMEL_UART_DTR - | ATMEL_UART_DSR - | ATMEL_UART_DCD - | ATMEL_UART_RI); - - /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */ - at91_register_uart(AT91SAM9260_ID_US1, 2, - ATMEL_UART_CTS - | ATMEL_UART_RTS); - - /* USART2 on ttyS3. (Rx & Tx only) */ - at91_register_uart(AT91SAM9260_ID_US2, 3, 0); - - /* USART3 on ttyS4. (Rx, Tx, RTS, CTS) */ - at91_register_uart(AT91SAM9260_ID_US3, 4, - ATMEL_UART_CTS - | ATMEL_UART_RTS); - - /* USART4 on ttyS5. (Rx & Tx only) */ - at91_register_uart(AT91SAM9260_ID_US4, 5, 0); - - /* USART5 on ttyS6. (Rx & Tx only) */ - at91_register_uart(AT91SAM9260_ID_US5, 6, 0); - - /* set serial console to ttyS0 (ie, DBGU) */ - at91_set_serial_console(0); - - /* Set the internal pull-up resistor on DRXD */ - at91_set_A_periph(AT91_PIN_PB14, 1); - -} - -static void __init foxg20_init_irq(void) -{ - at91sam9260_init_interrupts(NULL); -} - - -/* - * USB Host port - */ -static struct at91_usbh_data __initdata foxg20_usbh_data = { - .ports = 2, -}; - -/* - * USB Device port - */ -static struct at91_udc_data __initdata foxg20_udc_data = { - .vbus_pin = AT91_PIN_PC6, - .pullup_pin = 0, /* pull-up driven by UDC */ -}; - - -/* - * SPI devices. - */ -static struct spi_board_info foxg20_spi_devices[] = { -#if !defined(CONFIG_MMC_AT91) - { - .modalias = "mtd_dataflash", - .chip_select = 1, - .max_speed_hz = 15 * 1000 * 1000, - .bus_num = 0, - }, -#endif -}; - - -/* - * MACB Ethernet device - */ -static struct at91_eth_data __initdata foxg20_macb_data = { - .phy_irq_pin = AT91_PIN_PA7, - .is_rmii = 1, -}; - -/* - * MCI (SD/MMC) - * det_pin, wp_pin and vcc_pin are not connected - */ -static struct at91_mmc_data __initdata foxg20_mmc_data = { - .slot_b = 1, - .wire4 = 1, -}; - - -/* - * LEDs - */ -static struct gpio_led foxg20_leds[] = { - { /* user led, red */ - .name = "user_led", - .gpio = AT91_PIN_PC7, - .active_low = 0, - .default_trigger = "heartbeat", - }, -}; - - -/* - * GPIO Buttons - */ -#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE) -static struct gpio_keys_button foxg20_buttons[] = { - { - .gpio = AT91_PIN_PC4, - .code = BTN_1, - .desc = "Button 1", - .active_low = 1, - .wakeup = 1, - }, -}; - -static struct gpio_keys_platform_data foxg20_button_data = { - .buttons = foxg20_buttons, - .nbuttons = ARRAY_SIZE(foxg20_buttons), -}; - -static struct platform_device foxg20_button_device = { - .name = "gpio-keys", - .id = -1, - .num_resources = 0, - .dev = { - .platform_data = &foxg20_button_data, - } -}; - -static void __init foxg20_add_device_buttons(void) -{ - at91_set_gpio_input(AT91_PIN_PC4, 1); /* btn1 */ - at91_set_deglitch(AT91_PIN_PC4, 1); - - platform_device_register(&foxg20_button_device); -} -#else -static void __init foxg20_add_device_buttons(void) {} -#endif - - -#if defined(CONFIG_W1_MASTER_GPIO) || defined(CONFIG_W1_MASTER_GPIO_MODULE) -static struct w1_gpio_platform_data w1_gpio_pdata = { - /* If you choose to use a pin other than PB16 it needs to be 3.3V */ - .pin = AT91_PIN_PB16, - .is_open_drain = 1, -}; - -static struct platform_device w1_device = { - .name = "w1-gpio", - .id = -1, - .dev.platform_data = &w1_gpio_pdata, -}; - -static void __init at91_add_device_w1(void) -{ - at91_set_GPIO_periph(w1_gpio_pdata.pin, 1); - at91_set_multi_drive(w1_gpio_pdata.pin, 1); - platform_device_register(&w1_device); -} - -#endif - - -static struct i2c_board_info __initdata foxg20_i2c_devices[] = { - { - I2C_BOARD_INFO("24c512", 0x50), - }, -}; - - -static void __init foxg20_board_init(void) -{ - /* Serial */ - at91_add_device_serial(); - /* USB Host */ - at91_add_device_usbh(&foxg20_usbh_data); - /* USB Device */ - at91_add_device_udc(&foxg20_udc_data); - /* SPI */ - at91_add_device_spi(foxg20_spi_devices, ARRAY_SIZE(foxg20_spi_devices)); - /* Ethernet */ - at91_add_device_eth(&foxg20_macb_data); - /* MMC */ - at91_add_device_mmc(0, &foxg20_mmc_data); - /* I2C */ - at91_add_device_i2c(foxg20_i2c_devices, ARRAY_SIZE(foxg20_i2c_devices)); - /* LEDs */ - at91_gpio_leds(foxg20_leds, ARRAY_SIZE(foxg20_leds)); - /* Push Buttons */ - foxg20_add_device_buttons(); -#if defined(CONFIG_W1_MASTER_GPIO) || defined(CONFIG_W1_MASTER_GPIO_MODULE) - at91_add_device_w1(); -#endif -} - -MACHINE_START(ACMENETUSFOXG20, "Acme Systems srl FOX Board G20") - /* Maintainer: Sergio Tanzilli */ - .boot_params = AT91_SDRAM_BASE + 0x100, - .timer = &at91sam926x_timer, - .map_io = foxg20_map_io, - .init_irq = foxg20_init_irq, - .init_machine = foxg20_board_init, -MACHINE_END diff --git a/trunk/arch/arm/mach-at91/board-gsia18s.c b/trunk/arch/arm/mach-at91/board-gsia18s.c deleted file mode 100644 index bc28136ee249..000000000000 --- a/trunk/arch/arm/mach-at91/board-gsia18s.c +++ /dev/null @@ -1,584 +0,0 @@ -/* - * Copyright (C) 2010 Christian Glindkamp - * taskit GmbH - * 2010 Igor Plyatov - * GeoSIG Ltd - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -#include -#include -#include -#include -#include -#include -#include - -#include -#include - -#include -#include -#include -#include - -#include "sam9_smc.h" -#include "generic.h" - -static void __init gsia18s_map_io(void) -{ - stamp9g20_map_io(); - - /* - * USART0 on ttyS1 (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI). - * Used for Internal Analog Modem. - */ - at91_register_uart(AT91SAM9260_ID_US0, 1, - ATMEL_UART_CTS | ATMEL_UART_RTS | - ATMEL_UART_DTR | ATMEL_UART_DSR | - ATMEL_UART_DCD | ATMEL_UART_RI); - /* - * USART1 on ttyS2 (Rx, Tx, CTS, RTS). - * Used for GPS or WiFi or Data stream. - */ - at91_register_uart(AT91SAM9260_ID_US1, 2, - ATMEL_UART_CTS | ATMEL_UART_RTS); - /* - * USART2 on ttyS3 (Rx, Tx, CTS, RTS). - * Used for External Modem. - */ - at91_register_uart(AT91SAM9260_ID_US2, 3, - ATMEL_UART_CTS | ATMEL_UART_RTS); - /* - * USART3 on ttyS4 (Rx, Tx, RTS). - * Used for RS-485. - */ - at91_register_uart(AT91SAM9260_ID_US3, 4, ATMEL_UART_RTS); - - /* - * USART4 on ttyS5 (Rx, Tx). - * Used for TRX433 Radio Module. - */ - at91_register_uart(AT91SAM9260_ID_US4, 5, 0); -} - -static void __init init_irq(void) -{ - at91sam9260_init_interrupts(NULL); -} - -/* - * Two USB Host ports - */ -static struct at91_usbh_data __initdata usbh_data = { - .ports = 2, -}; - -/* - * USB Device port - */ -static struct at91_udc_data __initdata udc_data = { - .vbus_pin = AT91_PIN_PA22, - .pullup_pin = 0, /* pull-up driven by UDC */ -}; - -/* - * MACB Ethernet device - */ -static struct at91_eth_data __initdata macb_data = { - .phy_irq_pin = AT91_PIN_PA28, - .is_rmii = 1, -}; - -/* - * LEDs and GPOs - */ -static struct gpio_led gpio_leds[] = { - { - .name = "gpo:spi1reset", - .gpio = AT91_PIN_PC1, - .active_low = 0, - .default_trigger = "none", - .default_state = LEDS_GPIO_DEFSTATE_OFF, - }, - { - .name = "gpo:trig_net_out", - .gpio = AT91_PIN_PB20, - .active_low = 0, - .default_trigger = "none", - .default_state = LEDS_GPIO_DEFSTATE_OFF, - }, - { - .name = "gpo:trig_net_dir", - .gpio = AT91_PIN_PB19, - .active_low = 0, - .default_trigger = "none", - .default_state = LEDS_GPIO_DEFSTATE_OFF, - }, - { - .name = "gpo:charge_dis", - .gpio = AT91_PIN_PC2, - .active_low = 0, - .default_trigger = "none", - .default_state = LEDS_GPIO_DEFSTATE_OFF, - }, - { - .name = "led:event", - .gpio = AT91_PIN_PB17, - .active_low = 1, - .default_trigger = "none", - .default_state = LEDS_GPIO_DEFSTATE_OFF, - }, - { - .name = "led:lan", - .gpio = AT91_PIN_PB18, - .active_low = 1, - .default_trigger = "none", - .default_state = LEDS_GPIO_DEFSTATE_OFF, - }, - { - .name = "led:error", - .gpio = AT91_PIN_PB16, - .active_low = 1, - .default_trigger = "none", - .default_state = LEDS_GPIO_DEFSTATE_ON, - } -}; - -static struct gpio_led_platform_data gpio_led_info = { - .leds = gpio_leds, - .num_leds = ARRAY_SIZE(gpio_leds), -}; - -static struct platform_device leds = { - .name = "leds-gpio", - .id = 0, - .dev = { - .platform_data = &gpio_led_info, - } -}; - -static void __init gsia18s_leds_init(void) -{ - platform_device_register(&leds); -} - -/* PCF8574 0x20 GPIO - U1 on the GS_IA18-CB_V3 board */ -static struct gpio_led pcf_gpio_leds1[] = { - { /* bit 0 */ - .name = "gpo:hdc_power", - .gpio = PCF_GPIO_HDC_POWER, - .active_low = 0, - .default_trigger = "none", - .default_state = LEDS_GPIO_DEFSTATE_OFF, - }, - { /* bit 1 */ - .name = "gpo:wifi_setup", - .gpio = PCF_GPIO_WIFI_SETUP, - .active_low = 1, - .default_trigger = "none", - .default_state = LEDS_GPIO_DEFSTATE_OFF, - }, - { /* bit 2 */ - .name = "gpo:wifi_enable", - .gpio = PCF_GPIO_WIFI_ENABLE, - .active_low = 1, - .default_trigger = "none", - .default_state = LEDS_GPIO_DEFSTATE_OFF, - }, - { /* bit 3 */ - .name = "gpo:wifi_reset", - .gpio = PCF_GPIO_WIFI_RESET, - .active_low = 1, - .default_trigger = "none", - .default_state = LEDS_GPIO_DEFSTATE_ON, - }, - /* bit 4 used as GPI */ - { /* bit 5 */ - .name = "gpo:gps_setup", - .gpio = PCF_GPIO_GPS_SETUP, - .active_low = 1, - .default_trigger = "none", - .default_state = LEDS_GPIO_DEFSTATE_OFF, - }, - { /* bit 6 */ - .name = "gpo:gps_standby", - .gpio = PCF_GPIO_GPS_STANDBY, - .active_low = 0, - .default_trigger = "none", - .default_state = LEDS_GPIO_DEFSTATE_ON, - }, - { /* bit 7 */ - .name = "gpo:gps_power", - .gpio = PCF_GPIO_GPS_POWER, - .active_low = 0, - .default_trigger = "none", - .default_state = LEDS_GPIO_DEFSTATE_OFF, - } -}; - -static struct gpio_led_platform_data pcf_gpio_led_info1 = { - .leds = pcf_gpio_leds1, - .num_leds = ARRAY_SIZE(pcf_gpio_leds1), -}; - -static struct platform_device pcf_leds1 = { - .name = "leds-gpio", /* GS_IA18-CB_board */ - .id = 1, - .dev = { - .platform_data = &pcf_gpio_led_info1, - } -}; - -/* PCF8574 0x22 GPIO - U1 on the GS_2G_OPT1-A_V0 board (Alarm) */ -static struct gpio_led pcf_gpio_leds2[] = { - { /* bit 0 */ - .name = "gpo:alarm_1", - .gpio = PCF_GPIO_ALARM1, - .active_low = 1, - .default_trigger = "none", - .default_state = LEDS_GPIO_DEFSTATE_OFF, - }, - { /* bit 1 */ - .name = "gpo:alarm_2", - .gpio = PCF_GPIO_ALARM2, - .active_low = 1, - .default_trigger = "none", - .default_state = LEDS_GPIO_DEFSTATE_OFF, - }, - { /* bit 2 */ - .name = "gpo:alarm_3", - .gpio = PCF_GPIO_ALARM3, - .active_low = 1, - .default_trigger = "none", - .default_state = LEDS_GPIO_DEFSTATE_OFF, - }, - { /* bit 3 */ - .name = "gpo:alarm_4", - .gpio = PCF_GPIO_ALARM4, - .active_low = 1, - .default_trigger = "none", - .default_state = LEDS_GPIO_DEFSTATE_OFF, - }, - /* bits 4, 5, 6 not used */ - { /* bit 7 */ - .name = "gpo:alarm_v_relay_on", - .gpio = PCF_GPIO_ALARM_V_RELAY_ON, - .active_low = 0, - .default_trigger = "none", - .default_state = LEDS_GPIO_DEFSTATE_OFF, - }, -}; - -static struct gpio_led_platform_data pcf_gpio_led_info2 = { - .leds = pcf_gpio_leds2, - .num_leds = ARRAY_SIZE(pcf_gpio_leds2), -}; - -static struct platform_device pcf_leds2 = { - .name = "leds-gpio", - .id = 2, - .dev = { - .platform_data = &pcf_gpio_led_info2, - } -}; - -/* PCF8574 0x24 GPIO U1 on the GS_2G-OPT23-A_V0 board (Modem) */ -static struct gpio_led pcf_gpio_leds3[] = { - { /* bit 0 */ - .name = "gpo:modem_power", - .gpio = PCF_GPIO_MODEM_POWER, - .active_low = 1, - .default_trigger = "none", - .default_state = LEDS_GPIO_DEFSTATE_OFF, - }, - /* bits 1 and 2 not used */ - { /* bit 3 */ - .name = "gpo:modem_reset", - .gpio = PCF_GPIO_MODEM_RESET, - .active_low = 1, - .default_trigger = "none", - .default_state = LEDS_GPIO_DEFSTATE_ON, - }, - /* bits 4, 5 and 6 not used */ - { /* bit 7 */ - .name = "gpo:trx_reset", - .gpio = PCF_GPIO_TRX_RESET, - .active_low = 1, - .default_trigger = "none", - .default_state = LEDS_GPIO_DEFSTATE_ON, - } -}; - -static struct gpio_led_platform_data pcf_gpio_led_info3 = { - .leds = pcf_gpio_leds3, - .num_leds = ARRAY_SIZE(pcf_gpio_leds3), -}; - -static struct platform_device pcf_leds3 = { - .name = "leds-gpio", - .id = 3, - .dev = { - .platform_data = &pcf_gpio_led_info3, - } -}; - -static void __init gsia18s_pcf_leds_init(void) -{ - platform_device_register(&pcf_leds1); - platform_device_register(&pcf_leds2); - platform_device_register(&pcf_leds3); -} - -/* - * SPI busses. - */ -static struct spi_board_info gsia18s_spi_devices[] = { - { /* User accessible spi0, cs0 used for communication with MSP RTC */ - .modalias = "spidev", - .bus_num = 0, - .chip_select = 0, - .max_speed_hz = 580000, - .mode = SPI_MODE_1, - }, - { /* User accessible spi1, cs0 used for communication with int. DSP */ - .modalias = "spidev", - .bus_num = 1, - .chip_select = 0, - .max_speed_hz = 5600000, - .mode = SPI_MODE_0, - }, - { /* User accessible spi1, cs1 used for communication with ext. DSP */ - .modalias = "spidev", - .bus_num = 1, - .chip_select = 1, - .max_speed_hz = 5600000, - .mode = SPI_MODE_0, - }, - { /* User accessible spi1, cs2 used for communication with ext. DSP */ - .modalias = "spidev", - .bus_num = 1, - .chip_select = 2, - .max_speed_hz = 5600000, - .mode = SPI_MODE_0, - }, - { /* User accessible spi1, cs3 used for communication with ext. DSP */ - .modalias = "spidev", - .bus_num = 1, - .chip_select = 3, - .max_speed_hz = 5600000, - .mode = SPI_MODE_0, - } -}; - -/* - * GPI Buttons - */ -static struct gpio_keys_button buttons[] = { - { - .gpio = GPIO_TRIG_NET_IN, - .code = BTN_1, - .desc = "TRIG_NET_IN", - .type = EV_KEY, - .active_low = 0, - .wakeup = 1, - }, - { /* SW80 on the GS_IA18_S-MN board*/ - .gpio = GPIO_CARD_UNMOUNT_0, - .code = BTN_2, - .desc = "Card umount 0", - .type = EV_KEY, - .active_low = 1, - .wakeup = 1, - }, - { /* SW79 on the GS_IA18_S-MN board*/ - .gpio = GPIO_CARD_UNMOUNT_1, - .code = BTN_3, - .desc = "Card umount 1", - .type = EV_KEY, - .active_low = 1, - .wakeup = 1, - }, - { /* SW280 on the GS_IA18-CB board*/ - .gpio = GPIO_KEY_POWER, - .code = KEY_POWER, - .desc = "Power Off Button", - .type = EV_KEY, - .active_low = 0, - .wakeup = 1, - } -}; - -static struct gpio_keys_platform_data button_data = { - .buttons = buttons, - .nbuttons = ARRAY_SIZE(buttons), -}; - -static struct platform_device button_device = { - .name = "gpio-keys", - .id = -1, - .num_resources = 0, - .dev = { - .platform_data = &button_data, - } -}; - -static void __init gsia18s_add_device_buttons(void) -{ - at91_set_gpio_input(GPIO_TRIG_NET_IN, 1); - at91_set_deglitch(GPIO_TRIG_NET_IN, 1); - at91_set_gpio_input(GPIO_CARD_UNMOUNT_0, 1); - at91_set_deglitch(GPIO_CARD_UNMOUNT_0, 1); - at91_set_gpio_input(GPIO_CARD_UNMOUNT_1, 1); - at91_set_deglitch(GPIO_CARD_UNMOUNT_1, 1); - at91_set_gpio_input(GPIO_KEY_POWER, 0); - at91_set_deglitch(GPIO_KEY_POWER, 1); - - platform_device_register(&button_device); -} - -/* - * I2C - */ -static int pcf8574x_0x20_setup(struct i2c_client *client, int gpio, - unsigned int ngpio, void *context) -{ - int status; - - status = gpio_request(gpio + PCF_GPIO_ETH_DETECT, "eth_det"); - if (status < 0) { - pr_err("error: can't request GPIO%d\n", - gpio + PCF_GPIO_ETH_DETECT); - return status; - } - status = gpio_direction_input(gpio + PCF_GPIO_ETH_DETECT); - if (status < 0) { - pr_err("error: can't setup GPIO%d as input\n", - gpio + PCF_GPIO_ETH_DETECT); - return status; - } - status = gpio_export(gpio + PCF_GPIO_ETH_DETECT, false); - if (status < 0) { - pr_err("error: can't export GPIO%d\n", - gpio + PCF_GPIO_ETH_DETECT); - return status; - } - status = gpio_sysfs_set_active_low(gpio + PCF_GPIO_ETH_DETECT, 1); - if (status < 0) { - pr_err("error: gpio_sysfs_set active_low(GPIO%d, 1)\n", - gpio + PCF_GPIO_ETH_DETECT); - return status; - } - - return 0; -} - -static int pcf8574x_0x20_teardown(struct i2c_client *client, int gpio, - unsigned ngpio, void *context) -{ - gpio_free(gpio + PCF_GPIO_ETH_DETECT); - return 0; -} - -static struct pcf857x_platform_data pcf20_pdata = { - .gpio_base = GS_IA18_S_PCF_GPIO_BASE0, - .n_latch = (1 << 4), - .setup = pcf8574x_0x20_setup, - .teardown = pcf8574x_0x20_teardown, -}; - -static struct pcf857x_platform_data pcf22_pdata = { - .gpio_base = GS_IA18_S_PCF_GPIO_BASE1, -}; - -static struct pcf857x_platform_data pcf24_pdata = { - .gpio_base = GS_IA18_S_PCF_GPIO_BASE2, -}; - -static struct i2c_board_info __initdata gsia18s_i2c_devices[] = { - { /* U1 on the GS_IA18-CB_V3 board */ - I2C_BOARD_INFO("pcf8574", 0x20), - .platform_data = &pcf20_pdata, - }, - { /* U1 on the GS_2G_OPT1-A_V0 board (Alarm) */ - I2C_BOARD_INFO("pcf8574", 0x22), - .platform_data = &pcf22_pdata, - }, - { /* U1 on the GS_2G-OPT23-A_V0 board (Modem) */ - I2C_BOARD_INFO("pcf8574", 0x24), - .platform_data = &pcf24_pdata, - }, - { /* U161 on the GS_IA18_S-MN board */ - I2C_BOARD_INFO("24c1024", 0x50), - }, - { /* U162 on the GS_IA18_S-MN board */ - I2C_BOARD_INFO("24c01", 0x53), - }, -}; - -/* - * Compact Flash - */ -static struct at91_cf_data __initdata gsia18s_cf1_data = { - .irq_pin = AT91_PIN_PA27, - .det_pin = AT91_PIN_PB30, - .rst_pin = AT91_PIN_PB31, - .chipselect = 5, - .flags = AT91_CF_TRUE_IDE, -}; - -/* Power Off by RTC */ -static void gsia18s_power_off(void) -{ - pr_notice("Power supply will be switched off automatically now or after 60 seconds without ArmDAS.\n"); - at91_set_gpio_output(AT91_PIN_PA25, 1); - /* Spin to death... */ - while (1) - ; -} - -static int __init gsia18s_power_off_init(void) -{ - pm_power_off = gsia18s_power_off; - return 0; -} - -/* ---------------------------------------------------------------------------*/ - -static void __init gsia18s_board_init(void) -{ - stamp9g20_board_init(); - at91_add_device_usbh(&usbh_data); - at91_add_device_udc(&udc_data); - at91_add_device_eth(&macb_data); - gsia18s_leds_init(); - gsia18s_pcf_leds_init(); - gsia18s_add_device_buttons(); - at91_add_device_i2c(gsia18s_i2c_devices, - ARRAY_SIZE(gsia18s_i2c_devices)); - at91_add_device_cf(&gsia18s_cf1_data); - at91_add_device_spi(gsia18s_spi_devices, - ARRAY_SIZE(gsia18s_spi_devices)); - gsia18s_power_off_init(); -} - -MACHINE_START(GSIA18S, "GS_IA18_S") - .boot_params = AT91_SDRAM_BASE + 0x100, - .timer = &at91sam926x_timer, - .map_io = gsia18s_map_io, - .init_irq = init_irq, - .init_machine = gsia18s_board_init, -MACHINE_END diff --git a/trunk/arch/arm/mach-at91/board-sam9m10g45ek.c b/trunk/arch/arm/mach-at91/board-sam9m10g45ek.c index 6c999dbd2bcf..86ff4b52db32 100644 --- a/trunk/arch/arm/mach-at91/board-sam9m10g45ek.c +++ b/trunk/arch/arm/mach-at91/board-sam9m10g45ek.c @@ -37,6 +37,7 @@ #include #include +#include #include #include #include diff --git a/trunk/arch/arm/mach-at91/include/mach/gsia18s.h b/trunk/arch/arm/mach-at91/include/mach/gsia18s.h deleted file mode 100644 index 307c194926f9..000000000000 --- a/trunk/arch/arm/mach-at91/include/mach/gsia18s.h +++ /dev/null @@ -1,33 +0,0 @@ -/* Buttons */ -#define GPIO_TRIG_NET_IN AT91_PIN_PB21 -#define GPIO_CARD_UNMOUNT_0 AT91_PIN_PB13 -#define GPIO_CARD_UNMOUNT_1 AT91_PIN_PB12 -#define GPIO_KEY_POWER AT91_PIN_PA25 - -/* PCF8574 0x20 GPIO - U1 on the GS_IA18-CB_V3 board */ -#define GS_IA18_S_PCF_GPIO_BASE0 NR_BUILTIN_GPIO -#define PCF_GPIO_HDC_POWER (GS_IA18_S_PCF_GPIO_BASE0 + 0) -#define PCF_GPIO_WIFI_SETUP (GS_IA18_S_PCF_GPIO_BASE0 + 1) -#define PCF_GPIO_WIFI_ENABLE (GS_IA18_S_PCF_GPIO_BASE0 + 2) -#define PCF_GPIO_WIFI_RESET (GS_IA18_S_PCF_GPIO_BASE0 + 3) -#define PCF_GPIO_ETH_DETECT 4 /* this is a GPI */ -#define PCF_GPIO_GPS_SETUP (GS_IA18_S_PCF_GPIO_BASE0 + 5) -#define PCF_GPIO_GPS_STANDBY (GS_IA18_S_PCF_GPIO_BASE0 + 6) -#define PCF_GPIO_GPS_POWER (GS_IA18_S_PCF_GPIO_BASE0 + 7) - -/* PCF8574 0x22 GPIO - U1 on the GS_2G_OPT1-A_V0 board (Alarm) */ -#define GS_IA18_S_PCF_GPIO_BASE1 (GS_IA18_S_PCF_GPIO_BASE0 + 8) -#define PCF_GPIO_ALARM1 (GS_IA18_S_PCF_GPIO_BASE1 + 0) -#define PCF_GPIO_ALARM2 (GS_IA18_S_PCF_GPIO_BASE1 + 1) -#define PCF_GPIO_ALARM3 (GS_IA18_S_PCF_GPIO_BASE1 + 2) -#define PCF_GPIO_ALARM4 (GS_IA18_S_PCF_GPIO_BASE1 + 3) -/* bits 4, 5, 6 not used */ -#define PCF_GPIO_ALARM_V_RELAY_ON (GS_IA18_S_PCF_GPIO_BASE1 + 7) - -/* PCF8574 0x24 GPIO U1 on the GS_2G-OPT23-A_V0 board (Modem) */ -#define GS_IA18_S_PCF_GPIO_BASE2 (GS_IA18_S_PCF_GPIO_BASE1 + 8) -#define PCF_GPIO_MODEM_POWER (GS_IA18_S_PCF_GPIO_BASE2 + 0) -#define PCF_GPIO_MODEM_RESET (GS_IA18_S_PCF_GPIO_BASE2 + 3) -/* bits 1, 2, 4, 5 not used */ -#define PCF_GPIO_TRX_RESET (GS_IA18_S_PCF_GPIO_BASE2 + 6) -/* bit 7 not used */ diff --git a/trunk/arch/arm/mach-imx/Kconfig b/trunk/arch/arm/mach-imx/Kconfig index 56684b517070..17d2e608a214 100644 --- a/trunk/arch/arm/mach-imx/Kconfig +++ b/trunk/arch/arm/mach-imx/Kconfig @@ -243,7 +243,6 @@ config MACH_MX27_3DS select IMX_HAVE_PLATFORM_MXC_EHCI select IMX_HAVE_PLATFORM_MXC_MMC select IMX_HAVE_PLATFORM_SPI_IMX - select MXC_DEBUG_BOARD select MXC_ULPI if USB_ULPI help Include support for MX27PDK platform. This includes specific diff --git a/trunk/arch/arm/mach-imx/mach-mx27_3ds.c b/trunk/arch/arm/mach-imx/mach-mx27_3ds.c index 164331518bdd..6fd0f8f6deb6 100644 --- a/trunk/arch/arm/mach-imx/mach-mx27_3ds.c +++ b/trunk/arch/arm/mach-imx/mach-mx27_3ds.c @@ -37,15 +37,12 @@ #include #include #include -#include -#include #include "devices-imx27.h" #define SD1_EN_GPIO (GPIO_PORTB + 25) #define OTG_PHY_RESET_GPIO (GPIO_PORTB + 23) #define SPI2_SS0 (GPIO_PORTD + 21) -#define EXPIO_PARENT_INT (MXC_INTERNAL_IRQS + GPIO_PORTC + 28) static const int mx27pdk_pins[] __initconst = { /* UART1 */ @@ -218,10 +215,10 @@ static struct regulator_init_data vgen_init = { static struct mc13783_regulator_init_data mx27_3ds_regulators[] = { { - .id = MC13783_REG_VMMC1, + .id = MC13783_REGU_VMMC1, .init_data = &vmmc1_init, }, { - .id = MC13783_REG_VGEN, + .id = MC13783_REGU_VGEN, .init_data = &vgen_init, }, }; @@ -279,9 +276,6 @@ static void __init mx27pdk_init(void) imx27_add_spi_imx1(&spi2_pdata); spi_register_board_info(mx27_3ds_spi_devs, ARRAY_SIZE(mx27_3ds_spi_devs)); - - if (mxc_expio_init(MX27_CS5_BASE_ADDR, EXPIO_PARENT_INT)) - pr_warn("Init of the debugboard failed, all devices on the debugboard are unusable.\n"); } static void __init mx27pdk_timer_init(void) diff --git a/trunk/arch/arm/mach-mx3/mach-mx31_3ds.c b/trunk/arch/arm/mach-mx3/mach-mx31_3ds.c index 6b4aa2c47107..4e516b49a901 100644 --- a/trunk/arch/arm/mach-mx3/mach-mx31_3ds.c +++ b/trunk/arch/arm/mach-mx3/mach-mx31_3ds.c @@ -147,10 +147,10 @@ static struct mc13783_regulator_init_data mx31_3ds_regulators[] = { .init_data = &pwgtx_init, }, { - .id = MC13783_REG_GPO1, /* Turn on 1.8V */ + .id = MC13783_REGU_GPO1, /* Turn on 1.8V */ .init_data = &gpo_init, }, { - .id = MC13783_REG_GPO3, /* Turn on 3.3V */ + .id = MC13783_REGU_GPO3, /* Turn on 3.3V */ .init_data = &gpo_init, }, }; diff --git a/trunk/arch/arm/mach-mx5/Kconfig b/trunk/arch/arm/mach-mx5/Kconfig index de4fa992fc3e..55254b6e9460 100644 --- a/trunk/arch/arm/mach-mx5/Kconfig +++ b/trunk/arch/arm/mach-mx5/Kconfig @@ -50,7 +50,6 @@ config MACH_MX51_BABBAGE config MACH_MX51_3DS bool "Support MX51PDK (3DS)" select SOC_IMX51 - select IMX_HAVE_PLATFORM_IMX_KEYPAD select IMX_HAVE_PLATFORM_IMX_UART select IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX select IMX_HAVE_PLATFORM_SPI_IMX @@ -78,7 +77,6 @@ choice config MACH_EUKREA_MBIMX51_BASEBOARD prompt "Eukrea MBIMX51 development board" bool - select IMX_HAVE_PLATFORM_IMX_KEYPAD select IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX help This adds board specific devices that can be found on Eukrea's @@ -126,28 +124,10 @@ config MACH_MX53_EVK bool "Support MX53 EVK platforms" select SOC_IMX53 select IMX_HAVE_PLATFORM_IMX_UART - select IMX_HAVE_PLATFORM_IMX_I2C - select IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX - select IMX_HAVE_PLATFORM_SPI_IMX help Include support for MX53 EVK platform. This includes specific configurations for the board and its peripherals. -config MACH_MX53_SMD - bool "Support MX53 SMD platforms" - select SOC_IMX53 - select IMX_HAVE_PLATFORM_IMX_UART - help - Include support for MX53 SMD platform. This includes specific - configurations for the board and its peripherals. - -config MACH_MX53_LOCO - bool "Support MX53 LOCO platforms" - select SOC_IMX53 - select IMX_HAVE_PLATFORM_IMX_UART - help - Include support for MX53 LOCO platform. This includes specific - configurations for the board and its peripherals. config MACH_MX50_RDP bool "Support MX50 reference design platform" diff --git a/trunk/arch/arm/mach-mx5/Makefile b/trunk/arch/arm/mach-mx5/Makefile index 0d43be98e51c..0c398baf11fe 100644 --- a/trunk/arch/arm/mach-mx5/Makefile +++ b/trunk/arch/arm/mach-mx5/Makefile @@ -10,8 +10,6 @@ obj-$(CONFIG_CPU_FREQ_IMX) += cpu_op-mx51.o obj-$(CONFIG_MACH_MX51_BABBAGE) += board-mx51_babbage.o obj-$(CONFIG_MACH_MX51_3DS) += board-mx51_3ds.o obj-$(CONFIG_MACH_MX53_EVK) += board-mx53_evk.o -obj-$(CONFIG_MACH_MX53_SMD) += board-mx53_smd.o -obj-$(CONFIG_MACH_MX53_LOCO) += board-mx53_loco.o obj-$(CONFIG_MACH_EUKREA_CPUIMX51) += board-cpuimx51.o obj-$(CONFIG_MACH_EUKREA_MBIMX51_BASEBOARD) += eukrea_mbimx51-baseboard.o obj-$(CONFIG_MACH_EUKREA_CPUIMX51SD) += board-cpuimx51sd.o diff --git a/trunk/arch/arm/mach-mx5/board-mx51_3ds.c b/trunk/arch/arm/mach-mx5/board-mx51_3ds.c index 49d644842379..e42bd2eb034e 100644 --- a/trunk/arch/arm/mach-mx5/board-mx51_3ds.c +++ b/trunk/arch/arm/mach-mx5/board-mx51_3ds.c @@ -12,6 +12,7 @@ #include #include +#include #include #include @@ -119,14 +120,14 @@ static int mx51_3ds_board_keymap[] = { KEY(3, 5, KEY_BACK) }; -static const struct matrix_keymap_data mx51_3ds_map_data __initconst = { +static struct matrix_keymap_data mx51_3ds_map_data = { .keymap = mx51_3ds_board_keymap, .keymap_size = ARRAY_SIZE(mx51_3ds_board_keymap), }; static void mxc_init_keypad(void) { - imx51_add_imx_keypad(&mx51_3ds_map_data); + mxc_register_device(&mxc_keypad_device, &mx51_3ds_map_data); } #else static inline void mxc_init_keypad(void) diff --git a/trunk/arch/arm/mach-mx5/board-mx53_evk.c b/trunk/arch/arm/mach-mx5/board-mx53_evk.c index caee04c08238..fa97d0d5dd05 100644 --- a/trunk/arch/arm/mach-mx5/board-mx53_evk.c +++ b/trunk/arch/arm/mach-mx5/board-mx53_evk.c @@ -21,11 +21,6 @@ #include #include -#include -#include -#include -#include -#include #include #include #include @@ -34,10 +29,6 @@ #include #include -#define SMD_FEC_PHY_RST IMX_GPIO_NR(7, 6) -#define EVK_ECSPI1_CS0 IMX_GPIO_NR(2, 30) -#define EVK_ECSPI1_CS1 IMX_GPIO_NR(3, 19) - #include "crm_regs.h" #include "devices-imx53.h" @@ -56,14 +47,6 @@ static iomux_v3_cfg_t mx53_evk_pads[] = { MX53_PAD_ATA_CS_1__UART3_RXD, MX53_PAD_ATA_DA_1__UART3_CTS, MX53_PAD_ATA_DA_2__UART3_RTS, - - MX53_PAD_EIM_D16__CSPI1_SCLK, - MX53_PAD_EIM_D17__CSPI1_MISO, - MX53_PAD_EIM_D18__CSPI1_MOSI, - - /* ecspi chip select lines */ - MX53_PAD_EIM_EB2__GPIO_2_30, - MX53_PAD_EIM_D19__GPIO_3_19, }; static const struct imxuart_platform_data mx53_evk_uart_pdata __initconst = { @@ -77,68 +60,11 @@ static inline void mx53_evk_init_uart(void) imx53_add_imx_uart(2, &mx53_evk_uart_pdata); } -static const struct imxi2c_platform_data mx53_evk_i2c_data __initconst = { - .bitrate = 100000, -}; - -static inline void mx53_evk_fec_reset(void) -{ - int ret; - - /* reset FEC PHY */ - ret = gpio_request(SMD_FEC_PHY_RST, "fec-phy-reset"); - if (ret) { - printk(KERN_ERR"failed to get GPIO_FEC_PHY_RESET: %d\n", ret); - return; - } - gpio_direction_output(SMD_FEC_PHY_RST, 0); - gpio_set_value(SMD_FEC_PHY_RST, 0); - msleep(1); - gpio_set_value(SMD_FEC_PHY_RST, 1); -} - -static struct fec_platform_data mx53_evk_fec_pdata = { - .phy = PHY_INTERFACE_MODE_RMII, -}; - -static struct spi_board_info mx53_evk_spi_board_info[] __initdata = { - { - .modalias = "mtd_dataflash", - .max_speed_hz = 25000000, - .bus_num = 0, - .chip_select = 1, - .mode = SPI_MODE_0, - .platform_data = NULL, - }, -}; - -static int mx53_evk_spi_cs[] = { - EVK_ECSPI1_CS0, - EVK_ECSPI1_CS1, -}; - -static const struct spi_imx_master mx53_evk_spi_data __initconst = { - .chipselect = mx53_evk_spi_cs, - .num_chipselect = ARRAY_SIZE(mx53_evk_spi_cs), -}; - static void __init mx53_evk_board_init(void) { mxc_iomux_v3_setup_multiple_pads(mx53_evk_pads, ARRAY_SIZE(mx53_evk_pads)); mx53_evk_init_uart(); - mx53_evk_fec_reset(); - imx53_add_fec(&mx53_evk_fec_pdata); - - imx53_add_imx_i2c(0, &mx53_evk_i2c_data); - imx53_add_imx_i2c(1, &mx53_evk_i2c_data); - - imx53_add_sdhci_esdhc_imx(0, NULL); - imx53_add_sdhci_esdhc_imx(1, NULL); - - spi_register_board_info(mx53_evk_spi_board_info, - ARRAY_SIZE(mx53_evk_spi_board_info)); - imx53_add_ecspi(0, &mx53_evk_spi_data); } static void __init mx53_evk_timer_init(void) diff --git a/trunk/arch/arm/mach-mx5/board-mx53_loco.c b/trunk/arch/arm/mach-mx5/board-mx53_loco.c deleted file mode 100644 index d1348e04ace3..000000000000 --- a/trunk/arch/arm/mach-mx5/board-mx53_loco.c +++ /dev/null @@ -1,111 +0,0 @@ -/* - * Copyright (C) 2011 Freescale Semiconductor, Inc. All Rights Reserved. - */ - -/* - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - - * You should have received a copy of the GNU General Public License along - * with this program; if not, write to the Free Software Foundation, Inc., - * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA. - */ - -#include -#include -#include -#include -#include - -#include -#include -#include -#include - -#include -#include -#include - -#include "crm_regs.h" -#include "devices-imx53.h" - -#define LOCO_FEC_PHY_RST IMX_GPIO_NR(7, 6) - -static iomux_v3_cfg_t mx53_loco_pads[] = { - MX53_PAD_CSI0_D10__UART1_TXD, - MX53_PAD_CSI0_D11__UART1_RXD, - MX53_PAD_ATA_DIOW__UART1_TXD, - MX53_PAD_ATA_DMACK__UART1_RXD, - - MX53_PAD_ATA_BUFFER_EN__UART2_RXD, - MX53_PAD_ATA_DMARQ__UART2_TXD, - MX53_PAD_ATA_DIOR__UART2_RTS, - MX53_PAD_ATA_INTRQ__UART2_CTS, - - MX53_PAD_ATA_CS_0__UART3_TXD, - MX53_PAD_ATA_CS_1__UART3_RXD, - MX53_PAD_ATA_DA_1__UART3_CTS, - MX53_PAD_ATA_DA_2__UART3_RTS, -}; - -static const struct imxuart_platform_data mx53_loco_uart_data __initconst = { - .flags = IMXUART_HAVE_RTSCTS, -}; - -static inline void mx53_loco_init_uart(void) -{ - imx53_add_imx_uart(0, &mx53_loco_uart_data); - imx53_add_imx_uart(1, &mx53_loco_uart_data); - imx53_add_imx_uart(2, &mx53_loco_uart_data); -} - -static inline void mx53_loco_fec_reset(void) -{ - int ret; - - /* reset FEC PHY */ - ret = gpio_request(LOCO_FEC_PHY_RST, "fec-phy-reset"); - if (ret) { - printk(KERN_ERR"failed to get GPIO_FEC_PHY_RESET: %d\n", ret); - return; - } - gpio_direction_output(LOCO_FEC_PHY_RST, 0); - msleep(1); - gpio_set_value(LOCO_FEC_PHY_RST, 1); -} - -static struct fec_platform_data mx53_loco_fec_data = { - .phy = PHY_INTERFACE_MODE_RMII, -}; - -static void __init mx53_loco_board_init(void) -{ - mxc_iomux_v3_setup_multiple_pads(mx53_loco_pads, - ARRAY_SIZE(mx53_loco_pads)); - mx53_loco_init_uart(); - mx53_loco_fec_reset(); - imx53_add_fec(&mx53_loco_fec_data); -} - -static void __init mx53_loco_timer_init(void) -{ - mx53_clocks_init(32768, 24000000, 0, 0); -} - -static struct sys_timer mx53_loco_timer = { - .init = mx53_loco_timer_init, -}; - -MACHINE_START(MX53_LOCO, "Freescale MX53 LOCO Board") - .map_io = mx53_map_io, - .init_irq = mx53_init_irq, - .init_machine = mx53_loco_board_init, - .timer = &mx53_loco_timer, -MACHINE_END diff --git a/trunk/arch/arm/mach-mx5/board-mx53_smd.c b/trunk/arch/arm/mach-mx5/board-mx53_smd.c deleted file mode 100644 index 7970f7a48588..000000000000 --- a/trunk/arch/arm/mach-mx5/board-mx53_smd.c +++ /dev/null @@ -1,111 +0,0 @@ -/* - * Copyright (C) 2011 Freescale Semiconductor, Inc. All Rights Reserved. - */ - -/* - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - - * You should have received a copy of the GNU General Public License along - * with this program; if not, write to the Free Software Foundation, Inc., - * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA. - */ - -#include -#include -#include -#include -#include - -#include -#include -#include -#include - -#include -#include -#include - -#include "crm_regs.h" -#include "devices-imx53.h" - -#define SMD_FEC_PHY_RST IMX_GPIO_NR(7, 6) - -static iomux_v3_cfg_t mx53_smd_pads[] = { - MX53_PAD_CSI0_D10__UART1_TXD, - MX53_PAD_CSI0_D11__UART1_RXD, - MX53_PAD_ATA_DIOW__UART1_TXD, - MX53_PAD_ATA_DMACK__UART1_RXD, - - MX53_PAD_ATA_BUFFER_EN__UART2_RXD, - MX53_PAD_ATA_DMARQ__UART2_TXD, - MX53_PAD_ATA_DIOR__UART2_RTS, - MX53_PAD_ATA_INTRQ__UART2_CTS, - - MX53_PAD_ATA_CS_0__UART3_TXD, - MX53_PAD_ATA_CS_1__UART3_RXD, - MX53_PAD_ATA_DA_1__UART3_CTS, - MX53_PAD_ATA_DA_2__UART3_RTS, -}; - -static const struct imxuart_platform_data mx53_smd_uart_data __initconst = { - .flags = IMXUART_HAVE_RTSCTS, -}; - -static inline void mx53_smd_init_uart(void) -{ - imx53_add_imx_uart(0, &mx53_smd_uart_data); - imx53_add_imx_uart(1, &mx53_smd_uart_data); - imx53_add_imx_uart(2, &mx53_smd_uart_data); -} - -static inline void mx53_smd_fec_reset(void) -{ - int ret; - - /* reset FEC PHY */ - ret = gpio_request(SMD_FEC_PHY_RST, "fec-phy-reset"); - if (ret) { - printk(KERN_ERR"failed to get GPIO_FEC_PHY_RESET: %d\n", ret); - return; - } - gpio_direction_output(SMD_FEC_PHY_RST, 0); - msleep(1); - gpio_set_value(SMD_FEC_PHY_RST, 1); -} - -static struct fec_platform_data mx53_smd_fec_data = { - .phy = PHY_INTERFACE_MODE_RMII, -}; - -static void __init mx53_smd_board_init(void) -{ - mxc_iomux_v3_setup_multiple_pads(mx53_smd_pads, - ARRAY_SIZE(mx53_smd_pads)); - mx53_smd_init_uart(); - mx53_smd_fec_reset(); - imx53_add_fec(&mx53_smd_fec_data); -} - -static void __init mx53_smd_timer_init(void) -{ - mx53_clocks_init(32768, 24000000, 22579200, 0); -} - -static struct sys_timer mx53_smd_timer = { - .init = mx53_smd_timer_init, -}; - -MACHINE_START(MX53_SMD, "Freescale MX53 SMD Board") - .map_io = mx53_map_io, - .init_irq = mx53_init_irq, - .init_machine = mx53_smd_board_init, - .timer = &mx53_smd_timer, -MACHINE_END diff --git a/trunk/arch/arm/mach-mx5/clock-mx51-mx53.c b/trunk/arch/arm/mach-mx5/clock-mx51-mx53.c index 0a19e7567c0b..785e1a336183 100644 --- a/trunk/arch/arm/mach-mx5/clock-mx51-mx53.c +++ b/trunk/arch/arm/mach-mx5/clock-mx51-mx53.c @@ -1191,11 +1191,6 @@ DEFINE_CLOCK(gpt_ipg_clk, 0, MXC_CCM_CCGR2, MXC_CCM_CCGRx_CG10_OFFSET, DEFINE_CLOCK(gpt_clk, 0, MXC_CCM_CCGR2, MXC_CCM_CCGRx_CG9_OFFSET, NULL, NULL, &ipg_clk, &gpt_ipg_clk); -DEFINE_CLOCK(pwm1_clk, 0, MXC_CCM_CCGR2, MXC_CCM_CCGRx_CG6_OFFSET, - NULL, NULL, &ipg_clk, NULL); -DEFINE_CLOCK(pwm2_clk, 0, MXC_CCM_CCGR2, MXC_CCM_CCGRx_CG8_OFFSET, - NULL, NULL, &ipg_clk, NULL); - /* I2C */ DEFINE_CLOCK(i2c1_clk, 0, MXC_CCM_CCGR1, MXC_CCM_CCGRx_CG9_OFFSET, NULL, NULL, &ipg_clk, NULL); @@ -1288,8 +1283,6 @@ static struct clk_lookup mx51_lookups[] = { _REGISTER_CLOCK("imx-uart.2", NULL, uart3_clk) _REGISTER_CLOCK(NULL, "gpt", gpt_clk) _REGISTER_CLOCK("fec.0", NULL, fec_clk) - _REGISTER_CLOCK("mxc_pwm.0", "pwm", pwm1_clk) - _REGISTER_CLOCK("mxc_pwm.1", "pwm", pwm2_clk) _REGISTER_CLOCK("imx-i2c.0", NULL, i2c1_clk) _REGISTER_CLOCK("imx-i2c.1", NULL, i2c2_clk) _REGISTER_CLOCK("imx-i2c.2", NULL, hsi2c_clk) @@ -1302,7 +1295,7 @@ static struct clk_lookup mx51_lookups[] = { _REGISTER_CLOCK("mxc-ehci.2", "usb_ahb", usb_ahb_clk) _REGISTER_CLOCK("fsl-usb2-udc", "usb", usboh3_clk) _REGISTER_CLOCK("fsl-usb2-udc", "usb_ahb", ahb_clk) - _REGISTER_CLOCK("imx-keypad", NULL, kpp_clk) + _REGISTER_CLOCK("imx-keypad.0", NULL, kpp_clk) _REGISTER_CLOCK("mxc_nand", NULL, nfc_clk) _REGISTER_CLOCK("imx-ssi.0", NULL, ssi1_clk) _REGISTER_CLOCK("imx-ssi.1", NULL, ssi2_clk) @@ -1333,13 +1326,6 @@ static struct clk_lookup mx53_lookups[] = { _REGISTER_CLOCK(NULL, "gpt", gpt_clk) _REGISTER_CLOCK("fec.0", NULL, fec_clk) _REGISTER_CLOCK(NULL, "iim_clk", iim_clk) - _REGISTER_CLOCK("imx-i2c.0", NULL, i2c1_clk) - _REGISTER_CLOCK("imx-i2c.1", NULL, i2c2_clk) - _REGISTER_CLOCK("sdhci-esdhc-imx.0", NULL, esdhc1_clk) - _REGISTER_CLOCK("sdhci-esdhc-imx.1", NULL, esdhc2_clk) - _REGISTER_CLOCK("imx53-ecspi.0", NULL, ecspi1_clk) - _REGISTER_CLOCK("imx53-ecspi.1", NULL, ecspi2_clk) - _REGISTER_CLOCK("imx53-cspi.0", NULL, cspi_clk) }; static void clk_tree_init(void) @@ -1377,6 +1363,7 @@ int __init mx51_clocks_init(unsigned long ckil, unsigned long osc, clk_tree_init(); + clk_set_parent(&uart_root_clk, &pll3_sw_clk); clk_enable(&cpu_clk); clk_enable(&main_bus_clk); @@ -1419,7 +1406,6 @@ int __init mx53_clocks_init(unsigned long ckil, unsigned long osc, clk_tree_init(); - clk_set_parent(&uart_root_clk, &pll3_sw_clk); clk_enable(&cpu_clk); clk_enable(&main_bus_clk); diff --git a/trunk/arch/arm/mach-mx5/devices-imx51.h b/trunk/arch/arm/mach-mx5/devices-imx51.h index 7fff485e5603..6302e4670000 100644 --- a/trunk/arch/arm/mach-mx5/devices-imx51.h +++ b/trunk/arch/arm/mach-mx5/devices-imx51.h @@ -47,11 +47,3 @@ extern const struct imx_spi_imx_data imx51_ecspi_data[] __initconst; extern const struct imx_imx2_wdt_data imx51_imx2_wdt_data[] __initconst; #define imx51_add_imx2_wdt(id, pdata) \ imx_add_imx2_wdt(&imx51_imx2_wdt_data[id]) - -extern const struct imx_mxc_pwm_data imx51_mxc_pwm_data[] __initconst; -#define imx51_add_mxc_pwm(id) \ - imx_add_mxc_pwm(&imx51_mxc_pwm_data[id]) - -extern const struct imx_imx_keypad_data imx51_imx_keypad_data __initconst; -#define imx51_add_imx_keypad(pdata) \ - imx_add_imx_keypad(&imx51_imx_keypad_data, pdata) diff --git a/trunk/arch/arm/mach-mx5/devices-imx53.h b/trunk/arch/arm/mach-mx5/devices-imx53.h index 8639735a117b..9d0ec2507fa6 100644 --- a/trunk/arch/arm/mach-mx5/devices-imx53.h +++ b/trunk/arch/arm/mach-mx5/devices-imx53.h @@ -8,24 +8,6 @@ #include #include -extern const struct imx_fec_data imx53_fec_data __initconst; -#define imx53_add_fec(pdata) \ - imx_add_fec(&imx53_fec_data, pdata) - extern const struct imx_imx_uart_1irq_data imx53_imx_uart_data[] __initconst; #define imx53_add_imx_uart(id, pdata) \ imx_add_imx_uart_1irq(&imx53_imx_uart_data[id], pdata) - - -extern const struct imx_imx_i2c_data imx53_imx_i2c_data[] __initconst; -#define imx53_add_imx_i2c(id, pdata) \ - imx_add_imx_i2c(&imx53_imx_i2c_data[id], pdata) - -extern const struct imx_sdhci_esdhc_imx_data -imx53_sdhci_esdhc_imx_data[] __initconst; -#define imx53_add_sdhci_esdhc_imx(id, pdata) \ - imx_add_sdhci_esdhc_imx(&imx53_sdhci_esdhc_imx_data[id], pdata) - -extern const struct imx_spi_imx_data imx53_ecspi_data[] __initconst; -#define imx53_add_ecspi(id, pdata) \ - imx_add_spi_imx(&imx53_ecspi_data[id], pdata) diff --git a/trunk/arch/arm/mach-mx5/devices.c b/trunk/arch/arm/mach-mx5/devices.c index 153ada53e575..1bda5cb339dc 100644 --- a/trunk/arch/arm/mach-mx5/devices.c +++ b/trunk/arch/arm/mach-mx5/devices.c @@ -120,6 +120,25 @@ struct platform_device mxc_usbh2_device = { }, }; +static struct resource mxc_kpp_resources[] = { + { + .start = MX51_MXC_INT_KPP, + .end = MX51_MXC_INT_KPP, + .flags = IORESOURCE_IRQ, + } , { + .start = MX51_KPP_BASE_ADDR, + .end = MX51_KPP_BASE_ADDR + 0x8 - 1, + .flags = IORESOURCE_MEM, + }, +}; + +struct platform_device mxc_keypad_device = { + .name = "imx-keypad", + .id = 0, + .num_resources = ARRAY_SIZE(mxc_kpp_resources), + .resource = mxc_kpp_resources, +}; + static struct mxc_gpio_port mxc_gpio_ports[] = { { .chip.label = "gpio-0", diff --git a/trunk/arch/arm/mach-mx5/devices.h b/trunk/arch/arm/mach-mx5/devices.h index 55a5129bc29f..16891aa3573c 100644 --- a/trunk/arch/arm/mach-mx5/devices.h +++ b/trunk/arch/arm/mach-mx5/devices.h @@ -3,3 +3,4 @@ extern struct platform_device mxc_usbh1_device; extern struct platform_device mxc_usbh2_device; extern struct platform_device mxc_usbdr_udc_device; extern struct platform_device mxc_hsi2c_device; +extern struct platform_device mxc_keypad_device; diff --git a/trunk/arch/arm/mach-mx5/eukrea_mbimx51-baseboard.c b/trunk/arch/arm/mach-mx5/eukrea_mbimx51-baseboard.c index e83ffadb65f8..c96d018ff8a2 100644 --- a/trunk/arch/arm/mach-mx5/eukrea_mbimx51-baseboard.c +++ b/trunk/arch/arm/mach-mx5/eukrea_mbimx51-baseboard.c @@ -21,6 +21,7 @@ #include #include #include +#include #include #include @@ -156,7 +157,7 @@ static int mbimx51_keymap[] = { KEY(3, 3, KEY_ENTER), }; -static const struct matrix_keymap_data mbimx51_map_data __initconst = { +static struct matrix_keymap_data mbimx51_map_data = { .keymap = mbimx51_keymap, .keymap_size = ARRAY_SIZE(mbimx51_keymap), }; @@ -208,7 +209,7 @@ void __init eukrea_mbimx51_baseboard_init(void) platform_add_devices(devices, ARRAY_SIZE(devices)); - imx51_add_imx_keypad(&mbimx51_map_data); + mxc_register_device(&mxc_keypad_device, &mbimx51_map_data); gpio_request(MBIMX51_TSC2007_GPIO, "tsc2007_irq"); gpio_direction_input(MBIMX51_TSC2007_GPIO); diff --git a/trunk/arch/arm/mach-mxs/Kconfig b/trunk/arch/arm/mach-mxs/Kconfig index 8bfc8df54617..c4ac7b415195 100644 --- a/trunk/arch/arm/mach-mxs/Kconfig +++ b/trunk/arch/arm/mach-mxs/Kconfig @@ -15,7 +15,7 @@ comment "MXS platforms:" config MACH_MX23EVK bool "Support MX23EVK Platform" select SOC_IMX23 - select MXS_HAVE_AMBA_DUART + select MXS_HAVE_PLATFORM_DUART default y help Include support for MX23EVK platform. This includes specific @@ -24,7 +24,7 @@ config MACH_MX23EVK config MACH_MX28EVK bool "Support MX28EVK Platform" select SOC_IMX28 - select MXS_HAVE_AMBA_DUART + select MXS_HAVE_PLATFORM_DUART select MXS_HAVE_PLATFORM_FEC default y help diff --git a/trunk/arch/arm/mach-mxs/clock-mx23.c b/trunk/arch/arm/mach-mxs/clock-mx23.c index b1a362ebfded..8f5a19ab558c 100644 --- a/trunk/arch/arm/mach-mxs/clock-mx23.c +++ b/trunk/arch/arm/mach-mxs/clock-mx23.c @@ -21,7 +21,6 @@ #include #include #include -#include #include #include @@ -438,12 +437,10 @@ _DEFINE_CLOCK(clk32k_clk, XTAL, TIMROT_CLK32K_GATE, &ref_xtal_clk); }, static struct clk_lookup lookups[] = { - /* for amba bus driver */ - _REGISTER_CLOCK("duart", "apb_pclk", xbus_clk) - /* for amba-pl011 driver */ - _REGISTER_CLOCK("duart", NULL, uart_clk) + _REGISTER_CLOCK("mxs-duart.0", NULL, uart_clk) _REGISTER_CLOCK("rtc", NULL, rtc_clk) _REGISTER_CLOCK(NULL, "hclk", hbus_clk) + _REGISTER_CLOCK(NULL, "xclk", xbus_clk) _REGISTER_CLOCK(NULL, "usb", usb_clk) _REGISTER_CLOCK(NULL, "audio", audio_clk) _REGISTER_CLOCK(NULL, "pwm", pwm_clk) @@ -521,12 +518,6 @@ int __init mx23_clocks_init(void) { clk_misc_init(); - clk_enable(&cpu_clk); - clk_enable(&hbus_clk); - clk_enable(&xbus_clk); - clk_enable(&emi_clk); - clk_enable(&uart_clk); - clkdev_add_table(lookups, ARRAY_SIZE(lookups)); mxs_timer_init(&clk32k_clk, MX23_INT_TIMER0); diff --git a/trunk/arch/arm/mach-mxs/clock-mx28.c b/trunk/arch/arm/mach-mxs/clock-mx28.c index 56312c092a9e..74e2103c6011 100644 --- a/trunk/arch/arm/mach-mxs/clock-mx28.c +++ b/trunk/arch/arm/mach-mxs/clock-mx28.c @@ -21,7 +21,6 @@ #include #include #include -#include #include #include @@ -603,12 +602,7 @@ _DEFINE_CLOCK(fec_clk, ENET, DISABLE, &hbus_clk); }, static struct clk_lookup lookups[] = { - /* for amba bus driver */ - _REGISTER_CLOCK("duart", "apb_pclk", xbus_clk) - /* for amba-pl011 driver */ - _REGISTER_CLOCK("duart", NULL, uart_clk) - _REGISTER_CLOCK("imx28-fec.0", NULL, fec_clk) - _REGISTER_CLOCK("imx28-fec.1", NULL, fec_clk) + _REGISTER_CLOCK("mxs-duart.0", NULL, uart_clk) _REGISTER_CLOCK("fec.0", NULL, fec_clk) _REGISTER_CLOCK("rtc", NULL, rtc_clk) _REGISTER_CLOCK("pll2", NULL, pll2_clk) @@ -732,12 +726,6 @@ int __init mx28_clocks_init(void) { clk_misc_init(); - clk_enable(&cpu_clk); - clk_enable(&hbus_clk); - clk_enable(&xbus_clk); - clk_enable(&emi_clk); - clk_enable(&uart_clk); - clkdev_add_table(lookups, ARRAY_SIZE(lookups)); mxs_timer_init(&clk32k_clk, MX28_INT_TIMER0); diff --git a/trunk/arch/arm/mach-mxs/devices-mx23.h b/trunk/arch/arm/mach-mxs/devices-mx23.h index 1256788561d0..d0f49fc0abb5 100644 --- a/trunk/arch/arm/mach-mxs/devices-mx23.h +++ b/trunk/arch/arm/mach-mxs/devices-mx23.h @@ -11,6 +11,6 @@ #include #include -extern const struct amba_device mx23_duart_device __initconst; +extern const struct mxs_duart_data mx23_duart_data __initconst; #define mx23_add_duart() \ - mxs_add_duart(&mx23_duart_device) + mxs_add_duart(&mx23_duart_data) diff --git a/trunk/arch/arm/mach-mxs/devices-mx28.h b/trunk/arch/arm/mach-mxs/devices-mx28.h index 33773a6333a2..00b736c434ba 100644 --- a/trunk/arch/arm/mach-mxs/devices-mx28.h +++ b/trunk/arch/arm/mach-mxs/devices-mx28.h @@ -11,9 +11,9 @@ #include #include -extern const struct amba_device mx28_duart_device __initconst; +extern const struct mxs_duart_data mx28_duart_data __initconst; #define mx28_add_duart() \ - mxs_add_duart(&mx28_duart_device) + mxs_add_duart(&mx28_duart_data) extern const struct mxs_fec_data mx28_fec_data[] __initconst; #define mx28_add_fec(id, pdata) \ diff --git a/trunk/arch/arm/mach-mxs/devices.c b/trunk/arch/arm/mach-mxs/devices.c index c20d54740b0b..6b60f02ca2e3 100644 --- a/trunk/arch/arm/mach-mxs/devices.c +++ b/trunk/arch/arm/mach-mxs/devices.c @@ -19,8 +19,9 @@ #include #include #include +#include #include -#include +#include struct platform_device *__init mxs_add_platform_device_dmamask( const char *name, int id, @@ -72,17 +73,3 @@ struct platform_device *__init mxs_add_platform_device_dmamask( return pdev; } - -int __init mxs_add_amba_device(const struct amba_device *dev) -{ - struct amba_device *adev = kmalloc(sizeof(*adev), GFP_KERNEL); - - if (!adev) { - pr_err("%s: failed to allocate memory", __func__); - return -ENOMEM; - } - - *adev = *dev; - - return amba_device_register(adev, &iomem_resource); -} diff --git a/trunk/arch/arm/mach-mxs/devices/Kconfig b/trunk/arch/arm/mach-mxs/devices/Kconfig index cf7dc1ae575b..a35a2dc55395 100644 --- a/trunk/arch/arm/mach-mxs/devices/Kconfig +++ b/trunk/arch/arm/mach-mxs/devices/Kconfig @@ -1,6 +1,5 @@ -config MXS_HAVE_AMBA_DUART +config MXS_HAVE_PLATFORM_DUART bool - select ARM_AMBA config MXS_HAVE_PLATFORM_FEC bool diff --git a/trunk/arch/arm/mach-mxs/devices/Makefile b/trunk/arch/arm/mach-mxs/devices/Makefile index d0a09f6934b8..4b5266a3e6d9 100644 --- a/trunk/arch/arm/mach-mxs/devices/Makefile +++ b/trunk/arch/arm/mach-mxs/devices/Makefile @@ -1,2 +1,2 @@ -obj-$(CONFIG_MXS_HAVE_AMBA_DUART) += amba-duart.o +obj-$(CONFIG_MXS_HAVE_PLATFORM_DUART) += platform-duart.o obj-$(CONFIG_MXS_HAVE_PLATFORM_FEC) += platform-fec.o diff --git a/trunk/arch/arm/mach-mxs/devices/amba-duart.c b/trunk/arch/arm/mach-mxs/devices/amba-duart.c deleted file mode 100644 index a559db09b49c..000000000000 --- a/trunk/arch/arm/mach-mxs/devices/amba-duart.c +++ /dev/null @@ -1,40 +0,0 @@ -/* - * Copyright (C) 2009-2010 Pengutronix - * Uwe Kleine-Koenig - * - * Copyright 2010 Freescale Semiconductor, Inc. All Rights Reserved. - * - * This program is free software; you can redistribute it and/or modify it under - * the terms of the GNU General Public License version 2 as published by the - * Free Software Foundation. - */ -#include -#include -#include -#include - -#define MXS_AMBA_DUART_DEVICE(name, soc) \ -const struct amba_device name##_device __initconst = { \ - .dev = { \ - .init_name = "duart", \ - }, \ - .res = { \ - .start = soc ## _DUART_BASE_ADDR, \ - .end = (soc ## _DUART_BASE_ADDR) + SZ_8K - 1, \ - .flags = IORESOURCE_MEM, \ - }, \ - .irq = {soc ## _INT_DUART, NO_IRQ}, \ -} - -#ifdef CONFIG_SOC_IMX23 -MXS_AMBA_DUART_DEVICE(mx23_duart, MX23); -#endif - -#ifdef CONFIG_SOC_IMX28 -MXS_AMBA_DUART_DEVICE(mx28_duart, MX28); -#endif - -int __init mxs_add_duart(const struct amba_device *dev) -{ - return mxs_add_amba_device(dev); -} diff --git a/trunk/arch/arm/mach-mxs/devices/platform-duart.c b/trunk/arch/arm/mach-mxs/devices/platform-duart.c new file mode 100644 index 000000000000..2fe0df5b0aad --- /dev/null +++ b/trunk/arch/arm/mach-mxs/devices/platform-duart.c @@ -0,0 +1,48 @@ +/* + * Copyright (C) 2009-2010 Pengutronix + * Uwe Kleine-Koenig + * + * Copyright 2010 Freescale Semiconductor, Inc. All Rights Reserved. + * + * This program is free software; you can redistribute it and/or modify it under + * the terms of the GNU General Public License version 2 as published by the + * Free Software Foundation. + */ +#include +#include +#include + +#define mxs_duart_data_entry(soc) \ + { \ + .iobase = soc ## _DUART_BASE_ADDR, \ + .irq = soc ## _INT_DUART, \ + } + +#ifdef CONFIG_SOC_IMX23 +const struct mxs_duart_data mx23_duart_data __initconst = + mxs_duart_data_entry(MX23); +#endif + +#ifdef CONFIG_SOC_IMX28 +const struct mxs_duart_data mx28_duart_data __initconst = + mxs_duart_data_entry(MX28); +#endif + +struct platform_device *__init mxs_add_duart( + const struct mxs_duart_data *data) +{ + struct resource res[] = { + { + .start = data->iobase, + .end = data->iobase + SZ_8K - 1, + .flags = IORESOURCE_MEM, + }, { + .start = data->irq, + .end = data->irq, + .flags = IORESOURCE_IRQ, + }, + }; + + return mxs_add_platform_device("mxs-duart", 0, res, ARRAY_SIZE(res), + NULL, 0); +} diff --git a/trunk/arch/arm/mach-mxs/devices/platform-fec.c b/trunk/arch/arm/mach-mxs/devices/platform-fec.c index c42dff72b46c..c08168cf3dec 100644 --- a/trunk/arch/arm/mach-mxs/devices/platform-fec.c +++ b/trunk/arch/arm/mach-mxs/devices/platform-fec.c @@ -45,6 +45,6 @@ struct platform_device *__init mxs_add_fec( }, }; - return mxs_add_platform_device("imx28-fec", data->id, + return mxs_add_platform_device("fec", data->id, res, ARRAY_SIZE(res), pdata, sizeof(*pdata)); } diff --git a/trunk/arch/arm/mach-mxs/include/mach/devices-common.h b/trunk/arch/arm/mach-mxs/include/mach/devices-common.h index 6c3d1a103433..3da48d4d3273 100644 --- a/trunk/arch/arm/mach-mxs/include/mach/devices-common.h +++ b/trunk/arch/arm/mach-mxs/include/mach/devices-common.h @@ -9,7 +9,6 @@ #include #include #include -#include struct platform_device *mxs_add_platform_device_dmamask( const char *name, int id, @@ -25,10 +24,14 @@ static inline struct platform_device *mxs_add_platform_device( name, id, res, num_resources, data, size_data, 0); } -int __init mxs_add_amba_device(const struct amba_device *dev); - /* duart */ -int __init mxs_add_duart(const struct amba_device *dev); +struct mxs_duart_data { + resource_size_t iobase; + resource_size_t iosize; + resource_size_t irq; +}; +struct platform_device *__init mxs_add_duart( + const struct mxs_duart_data *data); /* fec */ #include diff --git a/trunk/arch/arm/mach-mxs/mach-mx28evk.c b/trunk/arch/arm/mach-mxs/mach-mx28evk.c index 8e2c5975001e..d162e95910f3 100644 --- a/trunk/arch/arm/mach-mxs/mach-mx28evk.c +++ b/trunk/arch/arm/mach-mxs/mach-mx28evk.c @@ -57,19 +57,6 @@ static const iomux_cfg_t mx28evk_pads[] __initconst = { (MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP), MX28_PAD_ENET_CLK__CLKCTRL_ENET | (MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP), - /* fec1 */ - MX28_PAD_ENET0_CRS__ENET1_RX_EN | - (MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP), - MX28_PAD_ENET0_RXD2__ENET1_RXD0 | - (MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP), - MX28_PAD_ENET0_RXD3__ENET1_RXD1 | - (MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP), - MX28_PAD_ENET0_COL__ENET1_TX_EN | - (MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP), - MX28_PAD_ENET0_TXD2__ENET1_TXD0 | - (MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP), - MX28_PAD_ENET0_TXD3__ENET1_TXD1 | - (MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP), /* phy power line */ MX28_PAD_SSP1_DATA3__GPIO_2_15 | (MXS_PAD_4MA | MXS_PAD_3V3 | MXS_PAD_NOPULL), @@ -119,14 +106,8 @@ static void __init mx28evk_fec_reset(void) gpio_set_value(MX28EVK_FEC_PHY_RESET, 1); } -static struct fec_platform_data mx28_fec_pdata[] = { - { - /* fec0 */ - .phy = PHY_INTERFACE_MODE_RMII, - }, { - /* fec1 */ - .phy = PHY_INTERFACE_MODE_RMII, - }, +static const struct fec_platform_data mx28_fec_pdata __initconst = { + .phy = PHY_INTERFACE_MODE_RMII, }; static void __init mx28evk_init(void) @@ -136,8 +117,7 @@ static void __init mx28evk_init(void) mx28_add_duart(); mx28evk_fec_reset(); - mx28_add_fec(0, &mx28_fec_pdata[0]); - mx28_add_fec(1, &mx28_fec_pdata[1]); + mx28_add_fec(0, &mx28_fec_pdata); } static void __init mx28evk_timer_init(void) diff --git a/trunk/arch/arm/plat-mxc/devices/Kconfig b/trunk/arch/arm/plat-mxc/devices/Kconfig index b9ab1d58b5e7..2537166468ac 100644 --- a/trunk/arch/arm/plat-mxc/devices/Kconfig +++ b/trunk/arch/arm/plat-mxc/devices/Kconfig @@ -1,6 +1,6 @@ config IMX_HAVE_PLATFORM_FEC bool - default y if ARCH_MX25 || SOC_IMX27 || SOC_IMX35 || SOC_IMX51 || SOC_IMX53 + default y if ARCH_MX25 || SOC_IMX27 || SOC_IMX35 || SOC_IMX51 config IMX_HAVE_PLATFORM_FLEXCAN select HAVE_CAN_FLEXCAN if CAN diff --git a/trunk/arch/arm/plat-mxc/devices/platform-fec.c b/trunk/arch/arm/plat-mxc/devices/platform-fec.c index b50c3517d083..269ec78aba77 100644 --- a/trunk/arch/arm/plat-mxc/devices/platform-fec.c +++ b/trunk/arch/arm/plat-mxc/devices/platform-fec.c @@ -36,11 +36,6 @@ const struct imx_fec_data imx51_fec_data __initconst = imx_fec_data_entry_single(MX51); #endif -#ifdef CONFIG_SOC_IMX53 -const struct imx_fec_data imx53_fec_data __initconst = - imx_fec_data_entry_single(MX53); -#endif - struct platform_device *__init imx_add_fec( const struct imx_fec_data *data, const struct fec_platform_data *pdata) diff --git a/trunk/arch/arm/plat-mxc/devices/platform-imx-i2c.c b/trunk/arch/arm/plat-mxc/devices/platform-imx-i2c.c index 7ba94e1bbda3..72ba880c75af 100644 --- a/trunk/arch/arm/plat-mxc/devices/platform-imx-i2c.c +++ b/trunk/arch/arm/plat-mxc/devices/platform-imx-i2c.c @@ -78,15 +78,6 @@ const struct imx_imx_i2c_data imx51_imx_i2c_data[] __initconst = { }; #endif /* ifdef CONFIG_SOC_IMX51 */ -#ifdef CONFIG_SOC_IMX53 -const struct imx_imx_i2c_data imx53_imx_i2c_data[] __initconst = { -#define imx53_imx_i2c_data_entry(_id, _hwid) \ - imx_imx_i2c_data_entry(MX53, _id, _hwid, SZ_4K) - imx53_imx_i2c_data_entry(0, 1), - imx53_imx_i2c_data_entry(1, 2), -}; -#endif /* ifdef CONFIG_SOC_IMX51 */ - struct platform_device *__init imx_add_imx_i2c( const struct imx_imx_i2c_data *data, const struct imxi2c_platform_data *pdata) diff --git a/trunk/arch/arm/plat-mxc/devices/platform-imx-keypad.c b/trunk/arch/arm/plat-mxc/devices/platform-imx-keypad.c index 26366114b021..40238f0b8643 100644 --- a/trunk/arch/arm/plat-mxc/devices/platform-imx-keypad.c +++ b/trunk/arch/arm/plat-mxc/devices/platform-imx-keypad.c @@ -41,11 +41,6 @@ const struct imx_imx_keypad_data imx35_imx_keypad_data __initconst = imx_imx_keypad_data_entry_single(MX35, SZ_16); #endif /* ifdef CONFIG_SOC_IMX35 */ -#ifdef CONFIG_SOC_IMX51 -const struct imx_imx_keypad_data imx51_imx_keypad_data __initconst = - imx_imx_keypad_data_entry_single(MX51, SZ_16); -#endif /* ifdef CONFIG_SOC_IMX51 */ - struct platform_device *__init imx_add_imx_keypad( const struct imx_imx_keypad_data *data, const struct matrix_keymap_data *pdata) diff --git a/trunk/arch/arm/plat-mxc/devices/platform-mxc_pwm.c b/trunk/arch/arm/plat-mxc/devices/platform-mxc_pwm.c index b0c4ae298111..3d8ebdba38ee 100644 --- a/trunk/arch/arm/plat-mxc/devices/platform-mxc_pwm.c +++ b/trunk/arch/arm/plat-mxc/devices/platform-mxc_pwm.c @@ -40,15 +40,6 @@ const struct imx_mxc_pwm_data imx27_mxc_pwm_data __initconst = imx_mxc_pwm_data_entry_single(MX27, 0, , SZ_4K); #endif /* ifdef CONFIG_SOC_IMX27 */ -#ifdef CONFIG_SOC_IMX51 -const struct imx_mxc_pwm_data imx51_mxc_pwm_data[] __initconst = { -#define imx51_mxc_pwm_data_entry(_id, _hwid) \ - imx_mxc_pwm_data_entry(MX51, _id, _hwid, SZ_16K) - imx51_mxc_pwm_data_entry(0, 1), - imx51_mxc_pwm_data_entry(1, 2), -}; -#endif /* ifdef CONFIG_SOC_IMX51 */ - struct platform_device *__init imx_add_mxc_pwm( const struct imx_mxc_pwm_data *data) { diff --git a/trunk/arch/arm/plat-mxc/devices/platform-sdhci-esdhc-imx.c b/trunk/arch/arm/plat-mxc/devices/platform-sdhci-esdhc-imx.c index 6b2940b93d94..b3525648a01d 100644 --- a/trunk/arch/arm/plat-mxc/devices/platform-sdhci-esdhc-imx.c +++ b/trunk/arch/arm/plat-mxc/devices/platform-sdhci-esdhc-imx.c @@ -53,18 +53,6 @@ imx51_sdhci_esdhc_imx_data[] __initconst = { }; #endif /* ifdef CONFIG_SOC_IMX51 */ -#ifdef CONFIG_SOC_IMX53 -const struct imx_sdhci_esdhc_imx_data -imx53_sdhci_esdhc_imx_data[] __initconst = { -#define imx53_sdhci_esdhc_imx_data_entry(_id, _hwid) \ - imx_sdhci_esdhc_imx_data_entry(MX53, _id, _hwid) - imx53_sdhci_esdhc_imx_data_entry(0, 1), - imx53_sdhci_esdhc_imx_data_entry(1, 2), - imx53_sdhci_esdhc_imx_data_entry(2, 3), - imx53_sdhci_esdhc_imx_data_entry(3, 4), -}; -#endif /* ifdef CONFIG_SOC_IMX53 */ - struct platform_device *__init imx_add_sdhci_esdhc_imx( const struct imx_sdhci_esdhc_imx_data *data, const struct esdhc_platform_data *pdata) diff --git a/trunk/arch/arm/plat-mxc/devices/platform-spi_imx.c b/trunk/arch/arm/plat-mxc/devices/platform-spi_imx.c index 013c85f20b58..8ea49adcdfc1 100644 --- a/trunk/arch/arm/plat-mxc/devices/platform-spi_imx.c +++ b/trunk/arch/arm/plat-mxc/devices/platform-spi_imx.c @@ -81,18 +81,6 @@ const struct imx_spi_imx_data imx51_ecspi_data[] __initconst = { }; #endif /* ifdef CONFIG_SOC_IMX51 */ -#ifdef CONFIG_SOC_IMX53 -const struct imx_spi_imx_data imx53_cspi_data __initconst = - imx_spi_imx_data_entry_single(MX53, CSPI, "imx53-cspi", 0, , SZ_4K); - -const struct imx_spi_imx_data imx53_ecspi_data[] __initconst = { -#define imx53_ecspi_data_entry(_id, _hwid) \ - imx_spi_imx_data_entry(MX53, ECSPI, "imx53-ecspi", _id, _hwid, SZ_4K) - imx53_ecspi_data_entry(0, 1), - imx53_ecspi_data_entry(1, 2), -}; -#endif /* ifdef CONFIG_SOC_IMX53 */ - struct platform_device *__init imx_add_spi_imx( const struct imx_spi_imx_data *data, const struct spi_imx_master *pdata) diff --git a/trunk/arch/arm/plat-mxc/include/mach/iomux-mx53.h b/trunk/arch/arm/plat-mxc/include/mach/iomux-mx53.h index 68e11d7ab79d..5deee019c29e 100644 --- a/trunk/arch/arm/plat-mxc/include/mach/iomux-mx53.h +++ b/trunk/arch/arm/plat-mxc/include/mach/iomux-mx53.h @@ -34,6 +34,7 @@ typedef enum iomux_config { IOMUX_CONFIG_ALT6, IOMUX_CONFIG_ALT7, IOMUX_CONFIG_GPIO, /* added to help user use GPIO mode */ + IOMUX_CONFIG_SION = 0x1 << 4, /* LOOPBACK:MUX SION bit */ } iomux_pin_cfg_t; /* These 2 defines are for pins that may not have a mux register, but could @@ -134,9 +135,6 @@ typedef enum iomux_config { #define MX53_PAD_EIM_D16__GPIO_3_16 IOMUX_PAD(0x460, 0x118,IOMUX_CONFIG_ALT1, 0x0, 0, NO_PAD_CTRL) #define MX53_PAD_EIM_D17__GPIO_3_17 IOMUX_PAD(0x464, 0x11C,IOMUX_CONFIG_ALT1, 0x0, 0, NO_PAD_CTRL) #define MX53_PAD_EIM_D18__GPIO_3_18 IOMUX_PAD(0x468, 0x120,IOMUX_CONFIG_ALT1, 0x0, 0, NO_PAD_CTRL) -#define MX53_PAD_EIM_D16__CSPI1_SCLK IOMUX_PAD(0x460, 0x118,IOMUX_CONFIG_ALT4, 0x79c, 3, NO_PAD_CTRL) -#define MX53_PAD_EIM_D17__CSPI1_MISO IOMUX_PAD(0x464, 0x11C,IOMUX_CONFIG_ALT4, 0x7a0, 3, NO_PAD_CTRL) -#define MX53_PAD_EIM_D18__CSPI1_MOSI IOMUX_PAD(0x468, 0x120,IOMUX_CONFIG_ALT4, 0x7a4, 3, NO_PAD_CTRL) #define MX53_PAD_EIM_D19__GPIO_3_19 IOMUX_PAD(0x46C, 0x124,IOMUX_CONFIG_ALT1, 0x0, 0, NO_PAD_CTRL) #define MX53_PAD_EIM_D20__GPIO_3_20 IOMUX_PAD(0x470, 0x128,IOMUX_CONFIG_ALT1, 0x0, 0, NO_PAD_CTRL) #define MX53_PAD_EIM_D21__GPIO_3_21 IOMUX_PAD(0x474, 0x12C,IOMUX_CONFIG_ALT1, 0x0, 0, NO_PAD_CTRL) diff --git a/trunk/arch/arm/plat-mxc/include/mach/iomux-v3.h b/trunk/arch/arm/plat-mxc/include/mach/iomux-v3.h index 82620af1922f..2277b01c855d 100644 --- a/trunk/arch/arm/plat-mxc/include/mach/iomux-v3.h +++ b/trunk/arch/arm/plat-mxc/include/mach/iomux-v3.h @@ -105,7 +105,6 @@ typedef u64 iomux_v3_cfg_t; #define PAD_CTL_SRE_FAST (1 << 0) #define PAD_CTL_SRE_SLOW (0 << 0) -#define IOMUX_CONFIG_SION (0x1 << 4) #define MX51_NUM_GPIO_PORT 4 diff --git a/trunk/arch/arm/plat-mxc/include/mach/mx51.h b/trunk/arch/arm/plat-mxc/include/mach/mx51.h index 1eb339e6c857..873807f96d70 100644 --- a/trunk/arch/arm/plat-mxc/include/mach/mx51.h +++ b/trunk/arch/arm/plat-mxc/include/mach/mx51.h @@ -301,8 +301,8 @@ #define MX51_MXC_INT_GPIO4_HIGH 57 #define MX51_MXC_INT_WDOG1 58 #define MX51_MXC_INT_WDOG2 59 -#define MX51_INT_KPP 60 -#define MX51_INT_PWM1 61 +#define MX51_MXC_INT_KPP 60 +#define MX51_MXC_INT_PWM1 61 #define MX51_INT_I2C1 62 #define MX51_INT_I2C2 63 #define MX51_MXC_INT_HS_I2C 64 @@ -335,7 +335,7 @@ #define MX51_MXC_INT_SPDIF 91 #define MX51_MXC_INT_TVE 92 #define MX51_MXC_INT_FIRI 93 -#define MX51_INT_PWM2 94 +#define MX51_MXC_INT_PWM2 94 #define MX51_MXC_INT_SLIM_EXP 95 #define MX51_INT_SSI3 96 #define MX51_MXC_INT_EMI_BOOT 97 diff --git a/trunk/arch/arm/plat-mxc/include/mach/mx53.h b/trunk/arch/arm/plat-mxc/include/mach/mx53.h index d7a8e52181ea..9577cdbf7fad 100644 --- a/trunk/arch/arm/plat-mxc/include/mach/mx53.h +++ b/trunk/arch/arm/plat-mxc/include/mach/mx53.h @@ -53,13 +53,13 @@ #define MX53_SPBA0_BASE_ADDR 0x50000000 #define MX53_SPBA0_SIZE SZ_1M -#define MX53_ESDHC1_BASE_ADDR (MX53_SPBA0_BASE_ADDR + 0x00004000) -#define MX53_ESDHC2_BASE_ADDR (MX53_SPBA0_BASE_ADDR + 0x00008000) +#define MX53_MMC_SDHC1_BASE_ADDR (MX53_SPBA0_BASE_ADDR + 0x00004000) +#define MX53_MMC_SDHC2_BASE_ADDR (MX53_SPBA0_BASE_ADDR + 0x00008000) #define MX53_UART3_BASE_ADDR (MX53_SPBA0_BASE_ADDR + 0x0000C000) -#define MX53_ECSPI1_BASE_ADDR (MX53_SPBA0_BASE_ADDR + 0x00010000) +#define MX53_CSPI1_BASE_ADDR (MX53_SPBA0_BASE_ADDR + 0x00010000) #define MX53_SSI2_BASE_ADDR (MX53_SPBA0_BASE_ADDR + 0x00014000) -#define MX53_ESDHC3_BASE_ADDR (MX53_SPBA0_BASE_ADDR + 0x00020000) -#define MX53_ESDHC4_BASE_ADDR (MX53_SPBA0_BASE_ADDR + 0x00024000) +#define MX53_MMC_SDHC3_BASE_ADDR (MX53_SPBA0_BASE_ADDR + 0x00020000) +#define MX53_MMC_SDHC4_BASE_ADDR (MX53_SPBA0_BASE_ADDR + 0x00024000) #define MX53_SPDIF_BASE_ADDR (MX53_SPBA0_BASE_ADDR + 0x00028000) #define MX53_ASRC_BASE_ADDR (MX53_SPBA0_BASE_ADDR + 0x0002C000) #define MX53_ATA_DMA_BASE_ADDR (MX53_SPBA0_BASE_ADDR + 0x00030000) @@ -117,12 +117,12 @@ #define MX53_ARM_BASE_ADDR (MX53_AIPS2_BASE_ADDR + 0x000A0000) #define MX53_OWIRE_BASE_ADDR (MX53_AIPS2_BASE_ADDR + 0x000A4000) #define MX53_FIRI_BASE_ADDR (MX53_AIPS2_BASE_ADDR + 0x000A8000) -#define MX53_ECSPI2_BASE_ADDR (MX53_AIPS2_BASE_ADDR + 0x000AC000) +#define MX53_CSPI2_BASE_ADDR (MX53_AIPS2_BASE_ADDR + 0x000AC000) #define MX53_SDMA_BASE_ADDR (MX53_AIPS2_BASE_ADDR + 0x000B0000) #define MX53_SCC_BASE_ADDR (MX53_AIPS2_BASE_ADDR + 0x000B4000) #define MX53_ROMCP_BASE_ADDR (MX53_AIPS2_BASE_ADDR + 0x000B8000) #define MX53_RTIC_BASE_ADDR (MX53_AIPS2_BASE_ADDR + 0x000BC000) -#define MX53_CSPI_BASE_ADDR (MX53_AIPS2_BASE_ADDR + 0x000C0000) +#define MX53_CSPI3_BASE_ADDR (MX53_AIPS2_BASE_ADDR + 0x000C0000) #define MX53_I2C2_BASE_ADDR (MX53_AIPS2_BASE_ADDR + 0x000C4000) #define MX53_I2C1_BASE_ADDR (MX53_AIPS2_BASE_ADDR + 0x000C8000) #define MX53_SSI1_BASE_ADDR (MX53_AIPS2_BASE_ADDR + 0x000CC000) @@ -136,7 +136,7 @@ #define MX53_MIPI_HSC_BASE_ADDR (MX53_AIPS2_BASE_ADDR + 0x000DC000) #define MX53_MLB_BASE_ADDR (MX53_AIPS2_BASE_ADDR + 0x000E4000) #define MX53_SSI3_BASE_ADDR (MX53_AIPS2_BASE_ADDR + 0x000E8000) -#define MX53_FEC_BASE_ADDR (MX53_AIPS2_BASE_ADDR + 0x000EC000) +#define MX53_MXC_FEC_BASE_ADDR (MX53_AIPS2_BASE_ADDR + 0x000EC000) #define MX53_TVE_BASE_ADDR (MX53_AIPS2_BASE_ADDR + 0x000F0000) #define MX53_VPU_BASE_ADDR (MX53_AIPS2_BASE_ADDR + 0x000F4000) #define MX53_SAHARA_BASE_ADDR (MX53_AIPS2_BASE_ADDR + 0x000F8000) @@ -229,10 +229,10 @@ * Interrupt numbers */ #define MX53_INT_RESV0 0 -#define MX53_INT_ESDHC1 1 -#define MX53_INT_ESDHC2 2 -#define MX53_INT_ESDHC3 3 -#define MX53_INT_ESDHC4 4 +#define MX53_INT_MMC_SDHC1 1 +#define MX53_INT_MMC_SDHC2 2 +#define MX53_INT_MMC_SDHC3 3 +#define MX53_INT_MMC_SDHC4 4 #define MX53_INT_RESV5 5 #define MX53_INT_SDMA 6 #define MX53_INT_IOMUX 7 @@ -264,8 +264,8 @@ #define MX53_INT_UART3 33 #define MX53_INT_RESV34 34 #define MX53_INT_RESV35 35 -#define MX53_INT_ECSPI1 36 -#define MX53_INT_ECSPI2 37 +#define MX53_INT_CSPI1 36 +#define MX53_INT_CSPI2 37 #define MX53_INT_CSPI 38 #define MX53_INT_GPT 39 #define MX53_INT_EPIT1 40 diff --git a/trunk/arch/arm/plat-mxc/pwm.c b/trunk/arch/arm/plat-mxc/pwm.c index 7a61ef8f471a..c36f2630ed93 100644 --- a/trunk/arch/arm/plat-mxc/pwm.c +++ b/trunk/arch/arm/plat-mxc/pwm.c @@ -57,7 +57,7 @@ int pwm_config(struct pwm_device *pwm, int duty_ns, int period_ns) if (pwm == NULL || period_ns == 0 || duty_ns > period_ns) return -EINVAL; - if (cpu_is_mx27() || cpu_is_mx3() || cpu_is_mx25() || cpu_is_mx51()) { + if (cpu_is_mx27() || cpu_is_mx3() || cpu_is_mx25()) { unsigned long long c; unsigned long period_cycles, duty_cycles, prescale; u32 cr;