diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig
index 1b8a45a4642a..ecc04ff13e95 100644
--- a/arch/arm/mach-omap2/Kconfig
+++ b/arch/arm/mach-omap2/Kconfig
@@ -171,12 +171,6 @@ config MACH_OMAP2_TUSB6010
 	depends on ARCH_OMAP2 && SOC_OMAP2420
 	default y if MACH_NOKIA_N8X0
 
-config MACH_OMAP3_BEAGLE
-	bool "OMAP3 BEAGLE board"
-	depends on ARCH_OMAP3
-	default y
-	select OMAP_PACKAGE_CBB
-
 config MACH_OMAP_LDP
 	bool "OMAP3 LDP board"
 	depends on ARCH_OMAP3
diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile
index a60e98689713..f1a68c63dc99 100644
--- a/arch/arm/mach-omap2/Makefile
+++ b/arch/arm/mach-omap2/Makefile
@@ -242,7 +242,6 @@ obj-$(CONFIG_SOC_OMAP2420)		+= msdi.o
 
 # Specific board support
 obj-$(CONFIG_MACH_OMAP_GENERIC)		+= board-generic.o pdata-quirks.o
-obj-$(CONFIG_MACH_OMAP3_BEAGLE)		+= board-omap3beagle.o
 obj-$(CONFIG_MACH_OMAP_LDP)		+= board-ldp.o
 obj-$(CONFIG_MACH_OMAP3530_LV_SOM)      += board-omap3logic.o
 obj-$(CONFIG_MACH_OMAP3_TORPEDO)        += board-omap3logic.o
diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c
deleted file mode 100644
index 81de1c68b360..000000000000
--- a/arch/arm/mach-omap2/board-omap3beagle.c
+++ /dev/null
@@ -1,595 +0,0 @@
-/*
- * linux/arch/arm/mach-omap2/board-omap3beagle.c
- *
- * Copyright (C) 2008 Texas Instruments
- *
- * Modified from mach-omap2/board-3430sdp.c
- *
- * Initial code: Syed Mohammed Khasim
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/delay.h>
-#include <linux/err.h>
-#include <linux/clk.h>
-#include <linux/io.h>
-#include <linux/leds.h>
-#include <linux/pwm.h>
-#include <linux/leds_pwm.h>
-#include <linux/gpio.h>
-#include <linux/input.h>
-#include <linux/gpio_keys.h>
-#include <linux/pm_opp.h>
-#include <linux/cpu.h>
-
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/partitions.h>
-#include <linux/mtd/nand.h>
-#include <linux/mmc/host.h>
-#include <linux/usb/phy.h>
-
-#include <linux/regulator/machine.h>
-#include <linux/i2c/twl.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/flash.h>
-
-#include <video/omapdss.h>
-#include <video/omap-panel-data.h>
-#include <linux/platform_data/mtd-nand-omap2.h>
-
-#include "common.h"
-#include "omap_device.h"
-#include "gpmc.h"
-#include "soc.h"
-#include "mux.h"
-#include "hsmmc.h"
-#include "pm.h"
-#include "board-flash.h"
-#include "common-board-devices.h"
-
-#define	NAND_CS	0
-
-static struct pwm_lookup pwm_lookup[] = {
-	/* LEDB -> PMU_STAT */
-	PWM_LOOKUP("twl-pwmled", 1, "leds_pwm", "beagleboard::pmu_stat",
-		   7812500, PWM_POLARITY_NORMAL),
-};
-
-static struct led_pwm pwm_leds[] = {
-	{
-		.name		= "beagleboard::pmu_stat",
-		.max_brightness	= 127,
-		.pwm_period_ns	= 7812500,
-	},
-};
-
-static struct led_pwm_platform_data pwm_data = {
-	.num_leds	= ARRAY_SIZE(pwm_leds),
-	.leds		= pwm_leds,
-};
-
-static struct platform_device leds_pwm = {
-	.name	= "leds_pwm",
-	.id	= -1,
-	.dev	= {
-		.platform_data = &pwm_data,
-	},
-};
-
-/*
- * OMAP3 Beagle revision
- * Run time detection of Beagle revision is done by reading GPIO.
- * GPIO ID -
- *	AXBX	= GPIO173, GPIO172, GPIO171: 1 1 1
- *	C1_3	= GPIO173, GPIO172, GPIO171: 1 1 0
- *	C4	= GPIO173, GPIO172, GPIO171: 1 0 1
- *	XMA/XMB = GPIO173, GPIO172, GPIO171: 0 0 0
- *	XMC = GPIO173, GPIO172, GPIO171: 0 1 0
- */
-enum {
-	OMAP3BEAGLE_BOARD_UNKN = 0,
-	OMAP3BEAGLE_BOARD_AXBX,
-	OMAP3BEAGLE_BOARD_C1_3,
-	OMAP3BEAGLE_BOARD_C4,
-	OMAP3BEAGLE_BOARD_XM,
-	OMAP3BEAGLE_BOARD_XMC,
-};
-
-static u8 omap3_beagle_version;
-
-/*
- * Board-specific configuration
- * Defaults to BeagleBoard-xMC
- */
-static struct {
-	int mmc1_gpio_wp;
-	bool usb_pwr_level;	/* 0 - Active Low, 1 - Active High */
-	int dvi_pd_gpio;
-	int usr_button_gpio;
-	int mmc_caps;
-} beagle_config = {
-	.mmc1_gpio_wp = -EINVAL,
-	.usb_pwr_level = 0,
-	.dvi_pd_gpio = -EINVAL,
-	.usr_button_gpio = 4,
-	.mmc_caps = MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
-};
-
-static struct gpio omap3_beagle_rev_gpios[] __initdata = {
-	{ 171, GPIOF_IN, "rev_id_0"    },
-	{ 172, GPIOF_IN, "rev_id_1" },
-	{ 173, GPIOF_IN, "rev_id_2"    },
-};
-
-static void __init omap3_beagle_init_rev(void)
-{
-	int ret;
-	u16 beagle_rev = 0;
-
-	omap_mux_init_gpio(171, OMAP_PIN_INPUT_PULLUP);
-	omap_mux_init_gpio(172, OMAP_PIN_INPUT_PULLUP);
-	omap_mux_init_gpio(173, OMAP_PIN_INPUT_PULLUP);
-
-	ret = gpio_request_array(omap3_beagle_rev_gpios,
-				 ARRAY_SIZE(omap3_beagle_rev_gpios));
-	if (ret < 0) {
-		printk(KERN_ERR "Unable to get revision detection GPIO pins\n");
-		omap3_beagle_version = OMAP3BEAGLE_BOARD_UNKN;
-		return;
-	}
-
-	beagle_rev = gpio_get_value(171) | (gpio_get_value(172) << 1)
-			| (gpio_get_value(173) << 2);
-
-	gpio_free_array(omap3_beagle_rev_gpios,
-			ARRAY_SIZE(omap3_beagle_rev_gpios));
-
-	switch (beagle_rev) {
-	case 7:
-		printk(KERN_INFO "OMAP3 Beagle Rev: Ax/Bx\n");
-		omap3_beagle_version = OMAP3BEAGLE_BOARD_AXBX;
-		beagle_config.mmc1_gpio_wp = 29;
-		beagle_config.dvi_pd_gpio = 170;
-		beagle_config.usr_button_gpio = 7;
-		break;
-	case 6:
-		printk(KERN_INFO "OMAP3 Beagle Rev: C1/C2/C3\n");
-		omap3_beagle_version = OMAP3BEAGLE_BOARD_C1_3;
-		beagle_config.mmc1_gpio_wp = 23;
-		beagle_config.dvi_pd_gpio = 170;
-		beagle_config.usr_button_gpio = 7;
-		break;
-	case 5:
-		printk(KERN_INFO "OMAP3 Beagle Rev: C4\n");
-		omap3_beagle_version = OMAP3BEAGLE_BOARD_C4;
-		beagle_config.mmc1_gpio_wp = 23;
-		beagle_config.dvi_pd_gpio = 170;
-		beagle_config.usr_button_gpio = 7;
-		break;
-	case 0:
-		printk(KERN_INFO "OMAP3 Beagle Rev: xM Ax/Bx\n");
-		omap3_beagle_version = OMAP3BEAGLE_BOARD_XM;
-		beagle_config.usb_pwr_level = 1;
-		beagle_config.mmc_caps &= ~MMC_CAP_8_BIT_DATA;
-		break;
-	case 2:
-		printk(KERN_INFO "OMAP3 Beagle Rev: xM C\n");
-		omap3_beagle_version = OMAP3BEAGLE_BOARD_XMC;
-		beagle_config.mmc_caps &= ~MMC_CAP_8_BIT_DATA;
-		break;
-	default:
-		printk(KERN_INFO "OMAP3 Beagle Rev: unknown %hd\n", beagle_rev);
-		omap3_beagle_version = OMAP3BEAGLE_BOARD_UNKN;
-	}
-}
-
-static struct mtd_partition omap3beagle_nand_partitions[] = {
-	/* All the partition sizes are listed in terms of NAND block size */
-	{
-		.name		= "X-Loader",
-		.offset		= 0,
-		.size		= 4 * NAND_BLOCK_SIZE,
-		.mask_flags	= MTD_WRITEABLE,	/* force read-only */
-	},
-	{
-		.name		= "U-Boot",
-		.offset		= MTDPART_OFS_APPEND,	/* Offset = 0x80000 */
-		.size		= 15 * NAND_BLOCK_SIZE,
-		.mask_flags	= MTD_WRITEABLE,	/* force read-only */
-	},
-	{
-		.name		= "U-Boot Env",
-		.offset		= MTDPART_OFS_APPEND,	/* Offset = 0x260000 */
-		.size		= 1 * NAND_BLOCK_SIZE,
-	},
-	{
-		.name		= "Kernel",
-		.offset		= MTDPART_OFS_APPEND,	/* Offset = 0x280000 */
-		.size		= 32 * NAND_BLOCK_SIZE,
-	},
-	{
-		.name		= "File System",
-		.offset		= MTDPART_OFS_APPEND,	/* Offset = 0x680000 */
-		.size		= MTDPART_SIZ_FULL,
-	},
-};
-
-/* DSS */
-
-static struct connector_dvi_platform_data beagle_dvi_connector_pdata = {
-	.name                   = "dvi",
-	.source                 = "tfp410.0",
-	.i2c_bus_num            = 3,
-};
-
-static struct platform_device beagle_dvi_connector_device = {
-	.name                   = "connector-dvi",
-	.id                     = 0,
-	.dev.platform_data      = &beagle_dvi_connector_pdata,
-};
-
-static struct encoder_tfp410_platform_data beagle_tfp410_pdata = {
-	.name                   = "tfp410.0",
-	.source                 = "dpi.0",
-	.data_lines             = 24,
-	.power_down_gpio        = -1,
-};
-
-static struct platform_device beagle_tfp410_device = {
-	.name                   = "tfp410",
-	.id                     = 0,
-	.dev.platform_data      = &beagle_tfp410_pdata,
-};
-
-static struct connector_atv_platform_data beagle_tv_pdata = {
-	.name = "tv",
-	.source = "venc.0",
-	.connector_type = OMAP_DSS_VENC_TYPE_SVIDEO,
-	.invert_polarity = false,
-};
-
-static struct platform_device beagle_tv_connector_device = {
-	.name                   = "connector-analog-tv",
-	.id                     = 0,
-	.dev.platform_data      = &beagle_tv_pdata,
-};
-
-static struct omap_dss_board_info beagle_dss_data = {
-	.default_display_name = "dvi",
-};
-
-#include "sdram-micron-mt46h32m32lf-6.h"
-
-static struct omap2_hsmmc_info mmc[] = {
-	{
-		.mmc		= 1,
-		.caps		= MMC_CAP_4_BIT_DATA,
-		.gpio_wp	= -EINVAL,
-		.deferred	= true,
-	},
-	{}	/* Terminator */
-};
-
-static struct regulator_consumer_supply beagle_vmmc1_supply[] = {
-	REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
-};
-
-static struct regulator_consumer_supply beagle_vsim_supply[] = {
-	REGULATOR_SUPPLY("vmmc_aux", "omap_hsmmc.0"),
-};
-
-static struct gpio_led gpio_leds[];
-
-static struct usbhs_phy_data phy_data[] = {
-	{
-		.port = 2,
-		.reset_gpio = 147,
-		.vcc_gpio = -1,		/* updated in beagle_twl_gpio_setup */
-		.vcc_polarity = 1,	/* updated in beagle_twl_gpio_setup */
-	},
-};
-
-static int beagle_twl_gpio_setup(struct device *dev,
-		unsigned gpio, unsigned ngpio)
-{
-	int r;
-
-	mmc[0].gpio_wp = beagle_config.mmc1_gpio_wp;
-	/* gpio + 0 is "mmc0_cd" (input/IRQ) */
-	mmc[0].gpio_cd = gpio + 0;
-	omap_hsmmc_late_init(mmc);
-
-	/*
-	 * TWL4030_GPIO_MAX + 0 == ledA, EHCI nEN_USB_PWR (out, XM active
-	 * high / others active low)
-	 * DVI reset GPIO is different between beagle revisions
-	 */
-	/* Valid for all -xM revisions */
-	if (cpu_is_omap3630()) {
-		/*
-		 * gpio + 1 on Xm controls the TFP410's enable line (active low)
-		 * gpio + 2 control varies depending on the board rev as below:
-		 * P7/P8 revisions(prototype): Camera EN
-		 * A2+ revisions (production): LDO (DVI, serial, led blocks)
-		 */
-		r = gpio_request_one(gpio + 1, GPIOF_OUT_INIT_LOW,
-				     "nDVI_PWR_EN");
-		if (r)
-			pr_err("%s: unable to configure nDVI_PWR_EN\n",
-				__func__);
-
-		beagle_config.dvi_pd_gpio = gpio + 2;
-
-	} else {
-		/*
-		 * REVISIT: need ehci-omap hooks for external VBUS
-		 * power switch and overcurrent detect
-		 */
-		if (gpio_request_one(gpio + 1, GPIOF_IN, "EHCI_nOC"))
-			pr_err("%s: unable to configure EHCI_nOC\n", __func__);
-	}
-	beagle_tfp410_pdata.power_down_gpio = beagle_config.dvi_pd_gpio;
-
-	platform_device_register(&beagle_tfp410_device);
-	platform_device_register(&beagle_dvi_connector_device);
-	platform_device_register(&beagle_tv_connector_device);
-
-	/* TWL4030_GPIO_MAX i.e. LED_GPO controls HS USB Port 2 power */
-	phy_data[0].vcc_gpio = gpio + TWL4030_GPIO_MAX;
-	phy_data[0].vcc_polarity = beagle_config.usb_pwr_level;
-
-	usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
-	return 0;
-}
-
-static struct twl4030_gpio_platform_data beagle_gpio_data = {
-	.use_leds	= true,
-	.pullups	= BIT(1),
-	.pulldowns	= BIT(2) | BIT(6) | BIT(7) | BIT(8) | BIT(13)
-				| BIT(15) | BIT(16) | BIT(17),
-	.setup		= beagle_twl_gpio_setup,
-};
-
-/* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
-static struct regulator_init_data beagle_vmmc1 = {
-	.constraints = {
-		.min_uV			= 1850000,
-		.max_uV			= 3150000,
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-					| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
-					| REGULATOR_CHANGE_MODE
-					| REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies	= ARRAY_SIZE(beagle_vmmc1_supply),
-	.consumer_supplies	= beagle_vmmc1_supply,
-};
-
-/* VSIM for MMC1 pins DAT4..DAT7 (2 mA, plus card == max 50 mA) */
-static struct regulator_init_data beagle_vsim = {
-	.constraints = {
-		.min_uV			= 1800000,
-		.max_uV			= 3000000,
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-					| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
-					| REGULATOR_CHANGE_MODE
-					| REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies	= ARRAY_SIZE(beagle_vsim_supply),
-	.consumer_supplies	= beagle_vsim_supply,
-};
-
-static struct twl4030_platform_data beagle_twldata = {
-	/* platform_data for children goes here */
-	.gpio		= &beagle_gpio_data,
-	.vmmc1		= &beagle_vmmc1,
-	.vsim		= &beagle_vsim,
-};
-
-static struct i2c_board_info __initdata beagle_i2c_eeprom[] = {
-       {
-               I2C_BOARD_INFO("eeprom", 0x50),
-       },
-};
-
-static int __init omap3_beagle_i2c_init(void)
-{
-	omap3_pmic_get_config(&beagle_twldata,
-			TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_MADC |
-			TWL_COMMON_PDATA_AUDIO,
-			TWL_COMMON_REGULATOR_VDAC | TWL_COMMON_REGULATOR_VPLL2);
-
-	beagle_twldata.vpll2->constraints.name = "VDVI";
-
-	omap3_pmic_init("twl4030", &beagle_twldata);
-	/* Bus 3 is attached to the DVI port where devices like the pico DLP
-	 * projector don't work reliably with 400kHz */
-	omap_register_i2c_bus(3, 100, beagle_i2c_eeprom, ARRAY_SIZE(beagle_i2c_eeprom));
-	return 0;
-}
-
-static struct gpio_led gpio_leds[] = {
-	{
-		.name			= "beagleboard::usr0",
-		.default_trigger	= "heartbeat",
-		.gpio			= 150,
-	},
-	{
-		.name			= "beagleboard::usr1",
-		.default_trigger	= "mmc0",
-		.gpio			= 149,
-	},
-};
-
-static struct gpio_led_platform_data gpio_led_info = {
-	.leds		= gpio_leds,
-	.num_leds	= ARRAY_SIZE(gpio_leds),
-};
-
-static struct platform_device leds_gpio = {
-	.name	= "leds-gpio",
-	.id	= -1,
-	.dev	= {
-		.platform_data	= &gpio_led_info,
-	},
-};
-
-static struct gpio_keys_button gpio_buttons[] = {
-	{
-		.code			= BTN_EXTRA,
-		/* Dynamically assigned depending on board */
-		.gpio			= -EINVAL,
-		.desc			= "user",
-		.wakeup			= 1,
-	},
-};
-
-static struct gpio_keys_platform_data gpio_key_info = {
-	.buttons	= gpio_buttons,
-	.nbuttons	= ARRAY_SIZE(gpio_buttons),
-};
-
-static struct platform_device keys_gpio = {
-	.name	= "gpio-keys",
-	.id	= -1,
-	.dev	= {
-		.platform_data	= &gpio_key_info,
-	},
-};
-
-static struct platform_device madc_hwmon = {
-	.name	= "twl4030_madc_hwmon",
-	.id	= -1,
-};
-
-static struct platform_device *omap3_beagle_devices[] __initdata = {
-	&leds_gpio,
-	&keys_gpio,
-	&madc_hwmon,
-	&leds_pwm,
-};
-
-static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
-	.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
-};
-
-#ifdef CONFIG_OMAP_MUX
-static struct omap_board_mux board_mux[] __initdata = {
-	{ .reg_offset = OMAP_MUX_TERMINATOR },
-};
-#endif
-
-static int __init beagle_opp_init(void)
-{
-	int r = 0;
-
-	if (!machine_is_omap3_beagle())
-		return 0;
-
-	/* Initialize the omap3 opp table if not already created. */
-	r = omap3_opp_init();
-	if (r < 0 && (r != -EEXIST)) {
-		pr_err("%s: opp default init failed\n", __func__);
-		return r;
-	}
-
-	/* Custom OPP enabled for all xM versions */
-	if (cpu_is_omap3630()) {
-		struct device *mpu_dev, *iva_dev;
-
-		mpu_dev = get_cpu_device(0);
-		iva_dev = omap_device_get_by_hwmod_name("iva");
-
-		if (!mpu_dev || IS_ERR(iva_dev)) {
-			pr_err("%s: Aiee.. no mpu/dsp devices? %p %p\n",
-				__func__, mpu_dev, iva_dev);
-			return -ENODEV;
-		}
-		/* Enable MPU 1GHz and lower opps */
-		r = dev_pm_opp_enable(mpu_dev, 800000000);
-		/* TODO: MPU 1GHz needs SR and ABB */
-
-		/* Enable IVA 800MHz and lower opps */
-		r |= dev_pm_opp_enable(iva_dev, 660000000);
-		/* TODO: DSP 800MHz needs SR and ABB */
-		if (r) {
-			pr_err("%s: failed to enable higher opp %d\n",
-				__func__, r);
-			/*
-			 * Cleanup - disable the higher freqs - we dont care
-			 * about the results
-			 */
-			dev_pm_opp_disable(mpu_dev, 800000000);
-			dev_pm_opp_disable(iva_dev, 660000000);
-		}
-	}
-	return 0;
-}
-omap_device_initcall(beagle_opp_init);
-
-static void __init omap3_beagle_init(void)
-{
-	omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
-	omap3_beagle_init_rev();
-
-	if (gpio_is_valid(beagle_config.mmc1_gpio_wp))
-		omap_mux_init_gpio(beagle_config.mmc1_gpio_wp, OMAP_PIN_INPUT);
-	mmc[0].caps = beagle_config.mmc_caps;
-	omap_hsmmc_init(mmc);
-
-	omap3_beagle_i2c_init();
-
-	gpio_buttons[0].gpio = beagle_config.usr_button_gpio;
-
-	platform_add_devices(omap3_beagle_devices,
-			ARRAY_SIZE(omap3_beagle_devices));
-	if (gpio_is_valid(beagle_config.dvi_pd_gpio))
-		omap_mux_init_gpio(beagle_config.dvi_pd_gpio, OMAP_PIN_OUTPUT);
-	omap_display_init(&beagle_dss_data);
-
-	omap_serial_init();
-	omap_sdrc_init(mt46h32m32lf6_sdrc_params,
-				  mt46h32m32lf6_sdrc_params);
-
-	usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
-	usb_musb_init(NULL);
-
-	usbhs_init(&usbhs_bdata);
-
-	board_nand_init(omap3beagle_nand_partitions,
-			ARRAY_SIZE(omap3beagle_nand_partitions), NAND_CS,
-			NAND_BUSWIDTH_16, NULL);
-	omap_twl4030_audio_init("omap3beagle", NULL);
-
-	/* Ensure msecure is mux'd to be able to set the RTC. */
-	omap_mux_init_signal("sys_drm_msecure", OMAP_PIN_OFF_OUTPUT_HIGH);
-
-	/* Ensure SDRC pins are mux'd for self-refresh */
-	omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
-	omap_mux_init_signal("sdrc_cke1", OMAP_PIN_OUTPUT);
-
-	pwm_add_table(pwm_lookup, ARRAY_SIZE(pwm_lookup));
-}
-
-MACHINE_START(OMAP3_BEAGLE, "OMAP3 Beagle Board")
-	/* Maintainer: Syed Mohammed Khasim - http://beagleboard.org */
-	.atag_offset	= 0x100,
-	.reserve	= omap_reserve,
-	.map_io		= omap3_map_io,
-	.init_early	= omap3_init_early,
-	.init_irq	= omap3_init_irq,
-	.init_machine	= omap3_beagle_init,
-	.init_late	= omap3_init_late,
-	.init_time	= omap3_secure_sync32k_timer_init,
-	.restart	= omap3xxx_restart,
-MACHINE_END