diff --git a/Documentation/devicetree/bindings/arm/spear-misc.txt b/Documentation/devicetree/bindings/arm/spear-misc.txt new file mode 100644 index 0000000000000..cf649827ffcd7 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/spear-misc.txt @@ -0,0 +1,9 @@ +SPEAr Misc configuration +=========================== +SPEAr SOCs have some miscellaneous registers which are used to configure +few properties of different peripheral controllers. + +misc node required properties: + +- compatible Should be "st,spear1340-misc", "syscon". +- reg: Address range of misc space upto 8K diff --git a/Documentation/devicetree/bindings/pci/spear13xx-pcie.txt b/Documentation/devicetree/bindings/pci/spear13xx-pcie.txt new file mode 100644 index 0000000000000..49ea76da77183 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/spear13xx-pcie.txt @@ -0,0 +1,14 @@ +SPEAr13XX PCIe DT detail: +================================ + +SPEAr13XX uses synopsis designware PCIe controller and ST MiPHY as phy +controller. + +Required properties: +- compatible : should be "st,spear1340-pcie", "snps,dw-pcie". +- phys : phandle to phy node associated with pcie controller +- phy-names : must be "pcie-phy" +- All other definitions as per generic PCI bindings + + Optional properties: +- st,pcie-is-gen1 indicates that forced gen1 initialization is needed. diff --git a/Documentation/devicetree/bindings/phy/st-spear-miphy.txt b/Documentation/devicetree/bindings/phy/st-spear-miphy.txt new file mode 100644 index 0000000000000..2a6bfdcc09b3e --- /dev/null +++ b/Documentation/devicetree/bindings/phy/st-spear-miphy.txt @@ -0,0 +1,15 @@ +ST SPEAr miphy DT details +========================= + +ST Microelectronics SPEAr miphy is a phy controller supporting PCIe and SATA. + +Required properties: +- compatible : should be "st,spear1310-miphy" or "st,spear1340-miphy" +- reg : offset and length of the PHY register set. +- misc: phandle for the syscon node to access misc registers +- #phy-cells : from the generic PHY bindings, must be 1. + - cell[1]: 0 if phy used for SATA, 1 for PCIe. + +Optional properties: +- phy-id: Instance id of the phy. Only required when there are multiple phys + present on a implementation. diff --git a/MAINTAINERS b/MAINTAINERS index 702ca10a5a6c3..766948ed64db0 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -6820,6 +6820,12 @@ S: Maintained F: Documentation/devicetree/bindings/pci/host-generic-pci.txt F: drivers/pci/host/pci-host-generic.c +PCIE DRIVER FOR ST SPEAR13XX +M: Mohit Kumar +L: linux-pci@vger.kernel.org +S: Maintained +F: drivers/pci/host/*spear* + PCMCIA SUBSYSTEM P: Linux PCMCIA Team L: linux-pcmcia@lists.infradead.org diff --git a/arch/arm/boot/dts/spear1310-evb.dts b/arch/arm/boot/dts/spear1310-evb.dts index b56a801e42a20..d42c84b1df8d0 100644 --- a/arch/arm/boot/dts/spear1310-evb.dts +++ b/arch/arm/boot/dts/spear1310-evb.dts @@ -106,6 +106,10 @@ status = "okay"; }; + miphy@eb800000 { + status = "okay"; + }; + cf@b2800000 { status = "okay"; }; diff --git a/arch/arm/boot/dts/spear1310.dtsi b/arch/arm/boot/dts/spear1310.dtsi index 122ae94076c8a..fa5f2bb5f106f 100644 --- a/arch/arm/boot/dts/spear1310.dtsi +++ b/arch/arm/boot/dts/spear1310.dtsi @@ -29,24 +29,111 @@ #gpio-cells = <2>; }; - ahci@b1000000 { + miphy0: miphy@eb800000 { + compatible = "st,spear1310-miphy"; + reg = <0xeb800000 0x4000>; + misc = <&misc>; + phy-id = <0>; + #phy-cells = <1>; + status = "disabled"; + }; + + miphy1: miphy@eb804000 { + compatible = "st,spear1310-miphy"; + reg = <0xeb804000 0x4000>; + misc = <&misc>; + phy-id = <1>; + #phy-cells = <1>; + status = "disabled"; + }; + + miphy2: miphy@eb808000 { + compatible = "st,spear1310-miphy"; + reg = <0xeb808000 0x4000>; + misc = <&misc>; + phy-id = <2>; + #phy-cells = <1>; + status = "disabled"; + }; + + ahci0: ahci@b1000000 { compatible = "snps,spear-ahci"; reg = <0xb1000000 0x10000>; interrupts = <0 68 0x4>; + phys = <&miphy0 0>; + phy-names = "sata-phy"; status = "disabled"; }; - ahci@b1800000 { + ahci1: ahci@b1800000 { compatible = "snps,spear-ahci"; reg = <0xb1800000 0x10000>; interrupts = <0 69 0x4>; + phys = <&miphy1 0>; + phy-names = "sata-phy"; status = "disabled"; }; - ahci@b4000000 { + ahci2: ahci@b4000000 { compatible = "snps,spear-ahci"; reg = <0xb4000000 0x10000>; interrupts = <0 70 0x4>; + phys = <&miphy2 0>; + phy-names = "sata-phy"; + status = "disabled"; + }; + + pcie0: pcie@b1000000 { + compatible = "st,spear1340-pcie", "snps,dw-pcie"; + reg = <0xb1000000 0x4000>; + interrupts = <0 68 0x4>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0x0 0 &gic 0 68 0x4>; + num-lanes = <1>; + phys = <&miphy0 1>; + phy-names = "pcie-phy"; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x00000800 0 0x80000000 0x80000000 0 0x00020000 /* configuration space */ + 0x81000000 0 0 0x80020000 0 0x00010000 /* downstream I/O */ + 0x82000000 0 0x80030000 0xc0030000 0 0x0ffd0000>; /* non-prefetchable memory */ + status = "disabled"; + }; + + pcie1: pcie@b1800000 { + compatible = "st,spear1340-pcie", "snps,dw-pcie"; + reg = <0xb1800000 0x4000>; + interrupts = <0 69 0x4>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0x0 0 &gic 0 69 0x4>; + num-lanes = <1>; + phys = <&miphy1 1>; + phy-names = "pcie-phy"; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x00000800 0 0x90000000 0x90000000 0 0x00020000 /* configuration space */ + 0x81000000 0 0 0x90020000 0 0x00010000 /* downstream I/O */ + 0x82000000 0 0x90030000 0x90030000 0 0x0ffd0000>; /* non-prefetchable memory */ + status = "disabled"; + }; + + pcie2: pcie@b4000000 { + compatible = "st,spear1340-pcie", "snps,dw-pcie"; + reg = <0xb4000000 0x4000>; + interrupts = <0 70 0x4>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0x0 0 &gic 0 70 0x4>; + num-lanes = <1>; + phys = <&miphy2 1>; + phy-names = "pcie-phy"; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x00000800 0 0xc0000000 0xc0000000 0 0x00020000 /* configuration space */ + 0x81000000 0 0 0xc0020000 0 0x00010000 /* downstream I/O */ + 0x82000000 0 0xc0030000 0xc0030000 0 0x0ffd0000>; /* non-prefetchable memory */ status = "disabled"; }; diff --git a/arch/arm/boot/dts/spear1340-evb.dts b/arch/arm/boot/dts/spear1340-evb.dts index d6c30ae0a8d75..b23e05ed1d602 100644 --- a/arch/arm/boot/dts/spear1340-evb.dts +++ b/arch/arm/boot/dts/spear1340-evb.dts @@ -122,6 +122,10 @@ status = "okay"; }; + miphy@eb800000 { + status = "okay"; + }; + dma@ea800000 { status = "okay"; }; diff --git a/arch/arm/boot/dts/spear1340.dtsi b/arch/arm/boot/dts/spear1340.dtsi index 54d128d35681a..e71df0f2cb52d 100644 --- a/arch/arm/boot/dts/spear1340.dtsi +++ b/arch/arm/boot/dts/spear1340.dtsi @@ -31,10 +31,38 @@ status = "disabled"; }; - ahci@b1000000 { + miphy0: miphy@eb800000 { + compatible = "st,spear1340-miphy"; + reg = <0xeb800000 0x4000>; + misc = <&misc>; + #phy-cells = <1>; + status = "disabled"; + }; + + ahci0: ahci@b1000000 { compatible = "snps,spear-ahci"; reg = <0xb1000000 0x10000>; interrupts = <0 72 0x4>; + phys = <&miphy0 0>; + phy-names = "sata-phy"; + status = "disabled"; + }; + + pcie0: pcie@b1000000 { + compatible = "st,spear1340-pcie", "snps,dw-pcie"; + reg = <0xb1000000 0x4000>; + interrupts = <0 68 0x4>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0x0 0 &gic 0 68 0x4>; + num-lanes = <1>; + phys = <&miphy0 1>; + phy-names = "pcie-phy"; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x00000800 0 0x80000000 0x80000000 0 0x00020000 /* configuration space */ + 0x81000000 0 0 0x80020000 0 0x00010000 /* downstream I/O */ + 0x82000000 0 0x80030000 0xc0030000 0 0x0ffd0000>; /* non-prefetchable memory */ status = "disabled"; }; diff --git a/arch/arm/boot/dts/spear13xx.dtsi b/arch/arm/boot/dts/spear13xx.dtsi index 4382547df58a7..a6eb5436d26d4 100644 --- a/arch/arm/boot/dts/spear13xx.dtsi +++ b/arch/arm/boot/dts/spear13xx.dtsi @@ -83,8 +83,8 @@ #size-cells = <1>; compatible = "simple-bus"; ranges = <0x50000000 0x50000000 0x10000000 - 0xb0000000 0xb0000000 0x10000000 - 0xd0000000 0xd0000000 0x02000000 + 0x80000000 0x80000000 0x20000000 + 0xb0000000 0xb0000000 0x22000000 0xd8000000 0xd8000000 0x01000000 0xe0000000 0xe0000000 0x10000000>; @@ -220,6 +220,11 @@ 0xd8000000 0xd8000000 0x01000000 0xe0000000 0xe0000000 0x10000000>; + misc: syscon@e0700000 { + compatible = "st,spear1340-misc", "syscon"; + reg = <0xe0700000 0x1000>; + }; + gpio0: gpio@e0600000 { compatible = "arm,pl061", "arm,primecell"; reg = <0xe0600000 0x1000>; diff --git a/arch/arm/configs/spear13xx_defconfig b/arch/arm/configs/spear13xx_defconfig index 82eaa552ed14e..d271b263f35d0 100644 --- a/arch/arm/configs/spear13xx_defconfig +++ b/arch/arm/configs/spear13xx_defconfig @@ -11,13 +11,24 @@ CONFIG_ARCH_SPEAR13XX=y CONFIG_MACH_SPEAR1310=y CONFIG_MACH_SPEAR1340=y # CONFIG_SWP_EMULATE is not set +CONFIG_PCI=y +CONFIG_PCI_MSI=y +CONFIG_PCIE_SPEAR13XX=y CONFIG_SMP=y # CONFIG_SMP_ON_UP is not set # CONFIG_ARM_CPU_TOPOLOGY is not set +CONFIG_AEABI=y CONFIG_ARM_APPENDED_DTB=y CONFIG_ARM_ATAG_DTB_COMPAT=y +CONFIG_VFP=y CONFIG_BINFMT_MISC=y CONFIG_NET=y +CONFIG_UNIX=y +CONFIG_INET=y +CONFIG_IP_PNP=y +CONFIG_IP_PNP_DHCP=y +CONFIG_IP_PNP_BOOTP=y +CONFIG_NET_IPIP=y CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_MTD=y CONFIG_MTD_OF_PARTS=y @@ -27,6 +38,7 @@ CONFIG_MTD_NAND=y CONFIG_MTD_NAND_FSMC=y CONFIG_BLK_DEV_RAM=y CONFIG_BLK_DEV_RAM_SIZE=16384 +CONFIG_BLK_DEV_SD=y CONFIG_ATA=y # CONFIG_SATA_PMP is not set CONFIG_SATA_AHCI_PLATFORM=y @@ -66,6 +78,7 @@ CONFIG_USB=y # CONFIG_USB_DEVICE_CLASS is not set CONFIG_USB_EHCI_HCD=y CONFIG_USB_OHCI_HCD=y +CONFIG_USB_STORAGE=y CONFIG_MMC=y CONFIG_MMC_SDHCI=y CONFIG_MMC_SDHCI_SPEAR=y @@ -79,11 +92,14 @@ CONFIG_EXT2_FS_SECURITY=y CONFIG_EXT3_FS=y CONFIG_EXT3_FS_SECURITY=y CONFIG_AUTOFS4_FS=m +CONFIG_FUSE_FS=y CONFIG_MSDOS_FS=m CONFIG_VFAT_FS=m CONFIG_FAT_DEFAULT_IOCHARSET="ascii" CONFIG_TMPFS=y CONFIG_JFFS2_FS=y +CONFIG_NFS_FS=y +CONFIG_ROOT_NFS=y CONFIG_NLS_DEFAULT="utf8" CONFIG_NLS_CODEPAGE_437=y CONFIG_NLS_ASCII=m diff --git a/arch/arm/mach-spear/Kconfig b/arch/arm/mach-spear/Kconfig index 90df2022276a7..6fd4dc88160b2 100644 --- a/arch/arm/mach-spear/Kconfig +++ b/arch/arm/mach-spear/Kconfig @@ -19,6 +19,8 @@ config ARCH_SPEAR13XX select HAVE_ARM_SCU if SMP select HAVE_ARM_TWD if SMP select PINCTRL + select MFD_SYSCON + select MIGHT_HAVE_PCI help Supports for ARM's SPEAR13XX family @@ -27,12 +29,14 @@ if ARCH_SPEAR13XX config MACH_SPEAR1310 bool "SPEAr1310 Machine support with Device Tree" select PINCTRL_SPEAR1310 + select PHY_ST_SPEAR1310_MIPHY help Supports ST SPEAr1310 machine configured via the device-tree config MACH_SPEAR1340 bool "SPEAr1340 Machine support with Device Tree" select PINCTRL_SPEAR1340 + select PHY_ST_SPEAR1340_MIPHY help Supports ST SPEAr1340 machine configured via the device-tree diff --git a/arch/arm/mach-spear/include/mach/spear.h b/arch/arm/mach-spear/include/mach/spear.h index 5cdc53d9b6533..f2d6a01765754 100644 --- a/arch/arm/mach-spear/include/mach/spear.h +++ b/arch/arm/mach-spear/include/mach/spear.h @@ -52,10 +52,10 @@ #ifdef CONFIG_ARCH_SPEAR13XX #define PERIP_GRP2_BASE UL(0xB3000000) -#define VA_PERIP_GRP2_BASE IOMEM(0xFE000000) +#define VA_PERIP_GRP2_BASE IOMEM(0xF9000000) #define MCIF_SDHCI_BASE UL(0xB3000000) #define SYSRAM0_BASE UL(0xB3800000) -#define VA_SYSRAM0_BASE IOMEM(0xFE800000) +#define VA_SYSRAM0_BASE IOMEM(0xF9800000) #define SYS_LOCATION (VA_SYSRAM0_BASE + 0x600) #define PERIP_GRP1_BASE UL(0xE0000000) diff --git a/arch/arm/mach-spear/spear1340.c b/arch/arm/mach-spear/spear1340.c index 7b6bff7154e11..3f3c0f124bd38 100644 --- a/arch/arm/mach-spear/spear1340.c +++ b/arch/arm/mach-spear/spear1340.c @@ -13,136 +13,13 @@ #define pr_fmt(fmt) "SPEAr1340: " fmt -#include -#include -#include #include #include #include "generic.h" -#include - -/* FIXME: Move SATA PHY code into a standalone driver */ - -/* Base addresses */ -#define SPEAR1340_SATA_BASE UL(0xB1000000) - -/* Power Management Registers */ -#define SPEAR1340_PCM_CFG (VA_MISC_BASE + 0x100) -#define SPEAR1340_PCM_WKUP_CFG (VA_MISC_BASE + 0x104) -#define SPEAR1340_SWITCH_CTR (VA_MISC_BASE + 0x108) - -#define SPEAR1340_PERIP1_SW_RST (VA_MISC_BASE + 0x318) -#define SPEAR1340_PERIP2_SW_RST (VA_MISC_BASE + 0x31C) -#define SPEAR1340_PERIP3_SW_RST (VA_MISC_BASE + 0x320) - -/* PCIE - SATA configuration registers */ -#define SPEAR1340_PCIE_SATA_CFG (VA_MISC_BASE + 0x424) - /* PCIE CFG MASks */ - #define SPEAR1340_PCIE_CFG_DEVICE_PRESENT (1 << 11) - #define SPEAR1340_PCIE_CFG_POWERUP_RESET (1 << 10) - #define SPEAR1340_PCIE_CFG_CORE_CLK_EN (1 << 9) - #define SPEAR1340_PCIE_CFG_AUX_CLK_EN (1 << 8) - #define SPEAR1340_SATA_CFG_TX_CLK_EN (1 << 4) - #define SPEAR1340_SATA_CFG_RX_CLK_EN (1 << 3) - #define SPEAR1340_SATA_CFG_POWERUP_RESET (1 << 2) - #define SPEAR1340_SATA_CFG_PM_CLK_EN (1 << 1) - #define SPEAR1340_PCIE_SATA_SEL_PCIE (0) - #define SPEAR1340_PCIE_SATA_SEL_SATA (1) - #define SPEAR1340_SATA_PCIE_CFG_MASK 0xF1F - #define SPEAR1340_PCIE_CFG_VAL (SPEAR1340_PCIE_SATA_SEL_PCIE | \ - SPEAR1340_PCIE_CFG_AUX_CLK_EN | \ - SPEAR1340_PCIE_CFG_CORE_CLK_EN | \ - SPEAR1340_PCIE_CFG_POWERUP_RESET | \ - SPEAR1340_PCIE_CFG_DEVICE_PRESENT) - #define SPEAR1340_SATA_CFG_VAL (SPEAR1340_PCIE_SATA_SEL_SATA | \ - SPEAR1340_SATA_CFG_PM_CLK_EN | \ - SPEAR1340_SATA_CFG_POWERUP_RESET | \ - SPEAR1340_SATA_CFG_RX_CLK_EN | \ - SPEAR1340_SATA_CFG_TX_CLK_EN) - -#define SPEAR1340_PCIE_MIPHY_CFG (VA_MISC_BASE + 0x428) - #define SPEAR1340_MIPHY_OSC_BYPASS_EXT (1 << 31) - #define SPEAR1340_MIPHY_CLK_REF_DIV2 (1 << 27) - #define SPEAR1340_MIPHY_CLK_REF_DIV4 (2 << 27) - #define SPEAR1340_MIPHY_CLK_REF_DIV8 (3 << 27) - #define SPEAR1340_MIPHY_PLL_RATIO_TOP(x) (x << 0) - #define SPEAR1340_PCIE_SATA_MIPHY_CFG_SATA \ - (SPEAR1340_MIPHY_OSC_BYPASS_EXT | \ - SPEAR1340_MIPHY_CLK_REF_DIV2 | \ - SPEAR1340_MIPHY_PLL_RATIO_TOP(60)) - #define SPEAR1340_PCIE_SATA_MIPHY_CFG_SATA_25M_CRYSTAL_CLK \ - (SPEAR1340_MIPHY_PLL_RATIO_TOP(120)) - #define SPEAR1340_PCIE_SATA_MIPHY_CFG_PCIE \ - (SPEAR1340_MIPHY_OSC_BYPASS_EXT | \ - SPEAR1340_MIPHY_PLL_RATIO_TOP(25)) - -/* SATA device registration */ -static int sata_miphy_init(struct device *dev, void __iomem *addr) -{ - writel(SPEAR1340_SATA_CFG_VAL, SPEAR1340_PCIE_SATA_CFG); - writel(SPEAR1340_PCIE_SATA_MIPHY_CFG_SATA_25M_CRYSTAL_CLK, - SPEAR1340_PCIE_MIPHY_CFG); - /* Switch on sata power domain */ - writel((readl(SPEAR1340_PCM_CFG) | (0x800)), SPEAR1340_PCM_CFG); - msleep(20); - /* Disable PCIE SATA Controller reset */ - writel((readl(SPEAR1340_PERIP1_SW_RST) & (~0x1000)), - SPEAR1340_PERIP1_SW_RST); - msleep(20); - - return 0; -} - -void sata_miphy_exit(struct device *dev) -{ - writel(0, SPEAR1340_PCIE_SATA_CFG); - writel(0, SPEAR1340_PCIE_MIPHY_CFG); - - /* Enable PCIE SATA Controller reset */ - writel((readl(SPEAR1340_PERIP1_SW_RST) | (0x1000)), - SPEAR1340_PERIP1_SW_RST); - msleep(20); - /* Switch off sata power domain */ - writel((readl(SPEAR1340_PCM_CFG) & (~0x800)), SPEAR1340_PCM_CFG); - msleep(20); -} - -int sata_suspend(struct device *dev) -{ - if (dev->power.power_state.event == PM_EVENT_FREEZE) - return 0; - - sata_miphy_exit(dev); - - return 0; -} - -int sata_resume(struct device *dev) -{ - if (dev->power.power_state.event == PM_EVENT_THAW) - return 0; - - return sata_miphy_init(dev, NULL); -} - -static struct ahci_platform_data sata_pdata = { - .init = sata_miphy_init, - .exit = sata_miphy_exit, - .suspend = sata_suspend, - .resume = sata_resume, -}; - -/* Add SPEAr1340 auxdata to pass platform data */ -static struct of_dev_auxdata spear1340_auxdata_lookup[] __initdata = { - OF_DEV_AUXDATA("snps,spear-ahci", SPEAR1340_SATA_BASE, NULL, - &sata_pdata), - {} -}; static void __init spear1340_dt_init(void) { - of_platform_populate(NULL, of_default_bus_match_table, - spear1340_auxdata_lookup, NULL); + of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL); platform_device_register_simple("spear-cpufreq", -1, NULL, 0); } diff --git a/arch/arm/mach-spear/spear13xx.c b/arch/arm/mach-spear/spear13xx.c index c9897ea389800..53a761482a7c9 100644 --- a/arch/arm/mach-spear/spear13xx.c +++ b/arch/arm/mach-spear/spear13xx.c @@ -52,7 +52,7 @@ void __init spear13xx_l2x0_init(void) /* * Following will create 16MB static virtual/physical mappings * PHYSICAL VIRTUAL - * 0xB3000000 0xFE000000 + * 0xB3000000 0xF9000000 * 0xE0000000 0xFD000000 * 0xEC000000 0xFC000000 * 0xED000000 0xFB000000 diff --git a/drivers/pci/host/Kconfig b/drivers/pci/host/Kconfig index 21df477be0c8a..2d8a4d05d78fc 100644 --- a/drivers/pci/host/Kconfig +++ b/drivers/pci/host/Kconfig @@ -46,4 +46,12 @@ config PCI_HOST_GENERIC Say Y here if you want to support a simple generic PCI host controller, such as the one emulated by kvmtool. +config PCIE_SPEAR13XX + tristate "STMicroelectronics SPEAr PCIe controller" + depends on ARCH_SPEAR13XX + select PCIEPORTBUS + select PCIE_DW + help + Say Y here if you want PCIe support on SPEAr13XX SoCs. + endmenu diff --git a/drivers/pci/host/Makefile b/drivers/pci/host/Makefile index 611ba4b48c949..0daec7941aba4 100644 --- a/drivers/pci/host/Makefile +++ b/drivers/pci/host/Makefile @@ -6,3 +6,4 @@ obj-$(CONFIG_PCI_TEGRA) += pci-tegra.o obj-$(CONFIG_PCI_RCAR_GEN2) += pci-rcar-gen2.o obj-$(CONFIG_PCI_RCAR_GEN2_PCIE) += pcie-rcar.o obj-$(CONFIG_PCI_HOST_GENERIC) += pci-host-generic.o +obj-$(CONFIG_PCIE_SPEAR13XX) += pcie-spear13xx.o diff --git a/drivers/pci/host/pcie-spear13xx.c b/drivers/pci/host/pcie-spear13xx.c new file mode 100644 index 0000000000000..99738e432596e --- /dev/null +++ b/drivers/pci/host/pcie-spear13xx.c @@ -0,0 +1,405 @@ +/* + * PCIe host controller driver for ST Microelectronics SPEAr13xx SoCs + * + * SPEAr13xx PCIe Glue Layer Source Code + * + * Copyright (C) 2010-2014 ST Microelectronics + * Pratyush Anand + * Mohit Kumar + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include "pcie-designware.h" + +struct spear13xx_pcie { + void __iomem *app_base; + struct phy *phy; + struct clk *clk; + struct pcie_port pp; + bool is_gen1; +}; + +struct pcie_app_reg { + u32 app_ctrl_0; /* cr0 */ + u32 app_ctrl_1; /* cr1 */ + u32 app_status_0; /* cr2 */ + u32 app_status_1; /* cr3 */ + u32 msg_status; /* cr4 */ + u32 msg_payload; /* cr5 */ + u32 int_sts; /* cr6 */ + u32 int_clr; /* cr7 */ + u32 int_mask; /* cr8 */ + u32 mst_bmisc; /* cr9 */ + u32 phy_ctrl; /* cr10 */ + u32 phy_status; /* cr11 */ + u32 cxpl_debug_info_0; /* cr12 */ + u32 cxpl_debug_info_1; /* cr13 */ + u32 ven_msg_ctrl_0; /* cr14 */ + u32 ven_msg_ctrl_1; /* cr15 */ + u32 ven_msg_data_0; /* cr16 */ + u32 ven_msg_data_1; /* cr17 */ + u32 ven_msi_0; /* cr18 */ + u32 ven_msi_1; /* cr19 */ + u32 mst_rmisc; /* cr20 */ +}; + +/* CR0 ID */ +#define RX_LANE_FLIP_EN_ID 0 +#define TX_LANE_FLIP_EN_ID 1 +#define SYS_AUX_PWR_DET_ID 2 +#define APP_LTSSM_ENABLE_ID 3 +#define SYS_ATTEN_BUTTON_PRESSED_ID 4 +#define SYS_MRL_SENSOR_STATE_ID 5 +#define SYS_PWR_FAULT_DET_ID 6 +#define SYS_MRL_SENSOR_CHGED_ID 7 +#define SYS_PRE_DET_CHGED_ID 8 +#define SYS_CMD_CPLED_INT_ID 9 +#define APP_INIT_RST_0_ID 11 +#define APP_REQ_ENTR_L1_ID 12 +#define APP_READY_ENTR_L23_ID 13 +#define APP_REQ_EXIT_L1_ID 14 +#define DEVICE_TYPE_EP (0 << 25) +#define DEVICE_TYPE_LEP (1 << 25) +#define DEVICE_TYPE_RC (4 << 25) +#define SYS_INT_ID 29 +#define MISCTRL_EN_ID 30 +#define REG_TRANSLATION_ENABLE 31 + +/* CR1 ID */ +#define APPS_PM_XMT_TURNOFF_ID 2 +#define APPS_PM_XMT_PME_ID 5 + +/* CR3 ID */ +#define XMLH_LTSSM_STATE_DETECT_QUIET 0x00 +#define XMLH_LTSSM_STATE_DETECT_ACT 0x01 +#define XMLH_LTSSM_STATE_POLL_ACTIVE 0x02 +#define XMLH_LTSSM_STATE_POLL_COMPLIANCE 0x03 +#define XMLH_LTSSM_STATE_POLL_CONFIG 0x04 +#define XMLH_LTSSM_STATE_PRE_DETECT_QUIET 0x05 +#define XMLH_LTSSM_STATE_DETECT_WAIT 0x06 +#define XMLH_LTSSM_STATE_CFG_LINKWD_START 0x07 +#define XMLH_LTSSM_STATE_CFG_LINKWD_ACEPT 0x08 +#define XMLH_LTSSM_STATE_CFG_LANENUM_WAIT 0x09 +#define XMLH_LTSSM_STATE_CFG_LANENUM_ACEPT 0x0A +#define XMLH_LTSSM_STATE_CFG_COMPLETE 0x0B +#define XMLH_LTSSM_STATE_CFG_IDLE 0x0C +#define XMLH_LTSSM_STATE_RCVRY_LOCK 0x0D +#define XMLH_LTSSM_STATE_RCVRY_SPEED 0x0E +#define XMLH_LTSSM_STATE_RCVRY_RCVRCFG 0x0F +#define XMLH_LTSSM_STATE_RCVRY_IDLE 0x10 +#define XMLH_LTSSM_STATE_L0 0x11 +#define XMLH_LTSSM_STATE_L0S 0x12 +#define XMLH_LTSSM_STATE_L123_SEND_EIDLE 0x13 +#define XMLH_LTSSM_STATE_L1_IDLE 0x14 +#define XMLH_LTSSM_STATE_L2_IDLE 0x15 +#define XMLH_LTSSM_STATE_L2_WAKE 0x16 +#define XMLH_LTSSM_STATE_DISABLED_ENTRY 0x17 +#define XMLH_LTSSM_STATE_DISABLED_IDLE 0x18 +#define XMLH_LTSSM_STATE_DISABLED 0x19 +#define XMLH_LTSSM_STATE_LPBK_ENTRY 0x1A +#define XMLH_LTSSM_STATE_LPBK_ACTIVE 0x1B +#define XMLH_LTSSM_STATE_LPBK_EXIT 0x1C +#define XMLH_LTSSM_STATE_LPBK_EXIT_TIMEOUT 0x1D +#define XMLH_LTSSM_STATE_HOT_RESET_ENTRY 0x1E +#define XMLH_LTSSM_STATE_HOT_RESET 0x1F +#define XMLH_LTSSM_STATE_MASK 0x3F +#define XMLH_LINK_UP (1 << 6) + +/* CR4 ID */ +#define CFG_MSI_EN_ID 18 + +/* CR6 */ +#define INTA_CTRL_INT (1 << 7) +#define INTB_CTRL_INT (1 << 8) +#define INTC_CTRL_INT (1 << 9) +#define INTD_CTRL_INT (1 << 10) +#define MSI_CTRL_INT (1 << 26) + +/* CR19 ID */ +#define VEN_MSI_REQ_ID 11 +#define VEN_MSI_FUN_NUM_ID 8 +#define VEN_MSI_TC_ID 5 +#define VEN_MSI_VECTOR_ID 0 +#define VEN_MSI_REQ_EN ((u32)0x1 << VEN_MSI_REQ_ID) +#define VEN_MSI_FUN_NUM_MASK ((u32)0x7 << VEN_MSI_FUN_NUM_ID) +#define VEN_MSI_TC_MASK ((u32)0x7 << VEN_MSI_TC_ID) +#define VEN_MSI_VECTOR_MASK ((u32)0x1F << VEN_MSI_VECTOR_ID) + +#define EXP_CAP_ID_OFFSET 0x70 + +#define to_spear13xx_pcie(x) container_of(x, struct spear13xx_pcie, pp) + +static int spear13xx_pcie_establish_link(struct pcie_port *pp) +{ + u32 val; + int count = 0; + struct spear13xx_pcie *spear13xx_pcie = to_spear13xx_pcie(pp); + struct pcie_app_reg *app_reg = spear13xx_pcie->app_base; + u32 exp_cap_off = EXP_CAP_ID_OFFSET; + + if (dw_pcie_link_up(pp)) { + dev_err(pp->dev, "link already up\n"); + return 0; + } + + dw_pcie_setup_rc(pp); + + /* + * this controller support only 128 bytes read size, however its + * default value in capability register is 512 bytes. So force + * it to 128 here. + */ + dw_pcie_cfg_read(pp->dbi_base, exp_cap_off + PCI_EXP_DEVCTL, 4, &val); + val &= ~PCI_EXP_DEVCTL_READRQ; + dw_pcie_cfg_write(pp->dbi_base, exp_cap_off + PCI_EXP_DEVCTL, 4, val); + + dw_pcie_cfg_write(pp->dbi_base, PCI_VENDOR_ID, 2, 0x104A); + dw_pcie_cfg_write(pp->dbi_base, PCI_DEVICE_ID, 2, 0xCD80); + + /* + * if is_gen1 is set then handle it, so that some buggy card + * also works + */ + if (spear13xx_pcie->is_gen1) { + dw_pcie_cfg_read(pp->dbi_base, exp_cap_off + PCI_EXP_LNKCAP, 4, + &val); + if ((val & PCI_EXP_LNKCAP_SLS) != PCI_EXP_LNKCAP_SLS_2_5GB) { + val &= ~((u32)PCI_EXP_LNKCAP_SLS); + val |= PCI_EXP_LNKCAP_SLS_2_5GB; + dw_pcie_cfg_write(pp->dbi_base, exp_cap_off + + PCI_EXP_LNKCAP, 4, val); + } + + dw_pcie_cfg_read(pp->dbi_base, exp_cap_off + PCI_EXP_LNKCTL2, 4, + &val); + if ((val & PCI_EXP_LNKCAP_SLS) != PCI_EXP_LNKCAP_SLS_2_5GB) { + val &= ~((u32)PCI_EXP_LNKCAP_SLS); + val |= PCI_EXP_LNKCAP_SLS_2_5GB; + dw_pcie_cfg_write(pp->dbi_base, exp_cap_off + + PCI_EXP_LNKCTL2, 4, val); + } + } + + /* enable ltssm */ + writel(DEVICE_TYPE_RC | (1 << MISCTRL_EN_ID) + | (1 << APP_LTSSM_ENABLE_ID) + | ((u32)1 << REG_TRANSLATION_ENABLE), + &app_reg->app_ctrl_0); + + /* check if the link is up or not */ + while (!dw_pcie_link_up(pp)) { + mdelay(100); + count++; + if (count == 10) { + dev_err(pp->dev, "link Fail\n"); + return -EINVAL; + } + } + dev_info(pp->dev, "link up\n"); + + return 0; +} + +static irqreturn_t spear13xx_pcie_irq_handler(int irq, void *arg) +{ + struct pcie_port *pp = arg; + struct spear13xx_pcie *spear13xx_pcie = to_spear13xx_pcie(pp); + struct pcie_app_reg *app_reg = spear13xx_pcie->app_base; + unsigned int status; + + status = readl(&app_reg->int_sts); + + if (status & MSI_CTRL_INT) { + if (!IS_ENABLED(CONFIG_PCI_MSI)) + BUG(); + dw_handle_msi_irq(pp); + } + + writel(status, &app_reg->int_clr); + + return IRQ_HANDLED; +} + +static void spear13xx_pcie_enable_interrupts(struct pcie_port *pp) +{ + struct spear13xx_pcie *spear13xx_pcie = to_spear13xx_pcie(pp); + struct pcie_app_reg *app_reg = spear13xx_pcie->app_base; + + /* Enable MSI interrupt */ + if (IS_ENABLED(CONFIG_PCI_MSI)) { + dw_pcie_msi_init(pp); + writel(readl(&app_reg->int_mask) | + MSI_CTRL_INT, &app_reg->int_mask); + } +} + +static int spear13xx_pcie_link_up(struct pcie_port *pp) +{ + struct spear13xx_pcie *spear13xx_pcie = to_spear13xx_pcie(pp); + struct pcie_app_reg *app_reg = spear13xx_pcie->app_base; + + if (readl(&app_reg->app_status_1) & XMLH_LINK_UP) + return 1; + + return 0; +} + +static void spear13xx_pcie_host_init(struct pcie_port *pp) +{ + spear13xx_pcie_establish_link(pp); + spear13xx_pcie_enable_interrupts(pp); +} + +static struct pcie_host_ops spear13xx_pcie_host_ops = { + .link_up = spear13xx_pcie_link_up, + .host_init = spear13xx_pcie_host_init, +}; + +static int add_pcie_port(struct pcie_port *pp, struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + int ret; + + pp->irq = platform_get_irq(pdev, 0); + if (!pp->irq) { + dev_err(dev, "failed to get irq\n"); + return -ENODEV; + } + ret = devm_request_irq(dev, pp->irq, spear13xx_pcie_irq_handler, + IRQF_SHARED, "spear1340-pcie", pp); + if (ret) { + dev_err(dev, "failed to request irq %d\n", pp->irq); + return ret; + } + + pp->root_bus_nr = -1; + pp->ops = &spear13xx_pcie_host_ops; + + ret = dw_pcie_host_init(pp); + if (ret) { + dev_err(dev, "failed to initialize host\n"); + return ret; + } + + return 0; +} + +static int __init spear13xx_pcie_probe(struct platform_device *pdev) +{ + struct spear13xx_pcie *spear13xx_pcie; + struct pcie_port *pp; + struct device *dev = &pdev->dev; + struct device_node *np = pdev->dev.of_node; + struct resource *dbi_base; + int ret; + + spear13xx_pcie = devm_kzalloc(dev, sizeof(*spear13xx_pcie), GFP_KERNEL); + if (!spear13xx_pcie) { + dev_err(dev, "no memory for SPEAr13xx pcie\n"); + return -ENOMEM; + } + + spear13xx_pcie->phy = devm_phy_get(dev, "pcie-phy"); + if (IS_ERR(spear13xx_pcie->phy)) { + ret = PTR_ERR(spear13xx_pcie->phy); + if (ret == -EPROBE_DEFER) + dev_info(dev, "probe deferred\n"); + else + dev_err(dev, "couldn't get pcie-phy\n"); + return ret; + } + + phy_init(spear13xx_pcie->phy); + + spear13xx_pcie->clk = devm_clk_get(dev, NULL); + if (IS_ERR(spear13xx_pcie->clk)) { + dev_err(dev, "couldn't get clk for pcie\n"); + return PTR_ERR(spear13xx_pcie->clk); + } + ret = clk_prepare_enable(spear13xx_pcie->clk); + if (ret) { + dev_err(dev, "couldn't enable clk for pcie\n"); + return ret; + } + + pp = &spear13xx_pcie->pp; + + pp->dev = dev; + + dbi_base = platform_get_resource(pdev, IORESOURCE_MEM, 0); + pp->dbi_base = devm_ioremap_resource(dev, dbi_base); + if (IS_ERR(pp->dbi_base)) { + dev_err(dev, "couldn't remap dbi base %p\n", dbi_base); + ret = PTR_ERR(pp->dbi_base); + goto fail_clk; + } + spear13xx_pcie->app_base = pp->dbi_base + 0x2000; + + if (of_property_read_bool(np, "st,pcie-is-gen1")) + spear13xx_pcie->is_gen1 = true; + + ret = add_pcie_port(pp, pdev); + if (ret < 0) + goto fail_clk; + + platform_set_drvdata(pdev, spear13xx_pcie); + return 0; + +fail_clk: + clk_disable_unprepare(spear13xx_pcie->clk); + + return ret; +} + +static int __exit spear13xx_pcie_remove(struct platform_device *pdev) +{ + struct spear13xx_pcie *spear13xx_pcie = platform_get_drvdata(pdev); + + clk_disable_unprepare(spear13xx_pcie->clk); + + phy_exit(spear13xx_pcie->phy); + + return 0; +} + +static const struct of_device_id spear13xx_pcie_of_match[] = { + { .compatible = "st,spear1340-pcie", }, + {}, +}; +MODULE_DEVICE_TABLE(of, spear13xx_pcie_of_match); + +static struct platform_driver spear13xx_pcie_driver = { + .probe = spear13xx_pcie_probe, + .remove = spear13xx_pcie_remove, + .driver = { + .name = "spear-pcie", + .owner = THIS_MODULE, + .of_match_table = of_match_ptr(spear13xx_pcie_of_match), + }, +}; + +/* SPEAr13xx PCIe driver does not allow module unload */ + +static int __init pcie_init(void) +{ + return platform_driver_register(&spear13xx_pcie_driver); +} +module_init(pcie_init); + +MODULE_DESCRIPTION("ST Microelectronics SPEAr13xx PCIe host controller driver"); +MODULE_AUTHOR("Pratyush Anand "); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig index 16a2f067c2420..e8f8a2d165d19 100644 --- a/drivers/phy/Kconfig +++ b/drivers/phy/Kconfig @@ -178,4 +178,16 @@ config PHY_XGENE help This option enables support for APM X-Gene SoC multi-purpose PHY. +config PHY_ST_SPEAR1310_MIPHY + tristate "ST SPEAR1310-MIPHY driver" + select GENERIC_PHY + help + Support for ST SPEAr1310 MIPHY which can be used for PCIe and SATA. + +config PHY_ST_SPEAR1340_MIPHY + tristate "ST SPEAR1340-MIPHY driver" + select GENERIC_PHY + help + Support for ST SPEAr1340 MIPHY which can be used for PCIe and SATA. + endmenu diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile index b4f1d57706015..d39609bb38dec 100644 --- a/drivers/phy/Makefile +++ b/drivers/phy/Makefile @@ -20,3 +20,5 @@ phy-exynos-usb2-$(CONFIG_PHY_EXYNOS4X12_USB2) += phy-exynos4x12-usb2.o phy-exynos-usb2-$(CONFIG_PHY_EXYNOS5250_USB2) += phy-exynos5250-usb2.o obj-$(CONFIG_PHY_EXYNOS5_USBDRD) += phy-exynos5-usbdrd.o obj-$(CONFIG_PHY_XGENE) += phy-xgene.o +obj-$(CONFIG_PHY_ST_SPEAR1310_MIPHY) += phy-spear1310-miphy.o +obj-$(CONFIG_PHY_ST_SPEAR1340_MIPHY) += phy-spear1340-miphy.o diff --git a/drivers/phy/phy-spear1310-miphy.c b/drivers/phy/phy-spear1310-miphy.c new file mode 100644 index 0000000000000..c58c869d57e05 --- /dev/null +++ b/drivers/phy/phy-spear1310-miphy.c @@ -0,0 +1,274 @@ +/* + * ST SPEAr1310-miphy driver + * + * Copyright (C) 2014 ST Microelectronics + * Pratyush Anand + * Mohit Kumar + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include + +/* SPEAr1310 Registers */ +#define SPEAR1310_PCIE_SATA_CFG 0x3A4 + #define SPEAR1310_PCIE_SATA2_SEL_PCIE (0 << 31) + #define SPEAR1310_PCIE_SATA1_SEL_PCIE (0 << 30) + #define SPEAR1310_PCIE_SATA0_SEL_PCIE (0 << 29) + #define SPEAR1310_PCIE_SATA2_SEL_SATA BIT(31) + #define SPEAR1310_PCIE_SATA1_SEL_SATA BIT(30) + #define SPEAR1310_PCIE_SATA0_SEL_SATA BIT(29) + #define SPEAR1310_SATA2_CFG_TX_CLK_EN BIT(27) + #define SPEAR1310_SATA2_CFG_RX_CLK_EN BIT(26) + #define SPEAR1310_SATA2_CFG_POWERUP_RESET BIT(25) + #define SPEAR1310_SATA2_CFG_PM_CLK_EN BIT(24) + #define SPEAR1310_SATA1_CFG_TX_CLK_EN BIT(23) + #define SPEAR1310_SATA1_CFG_RX_CLK_EN BIT(22) + #define SPEAR1310_SATA1_CFG_POWERUP_RESET BIT(21) + #define SPEAR1310_SATA1_CFG_PM_CLK_EN BIT(20) + #define SPEAR1310_SATA0_CFG_TX_CLK_EN BIT(19) + #define SPEAR1310_SATA0_CFG_RX_CLK_EN BIT(18) + #define SPEAR1310_SATA0_CFG_POWERUP_RESET BIT(17) + #define SPEAR1310_SATA0_CFG_PM_CLK_EN BIT(16) + #define SPEAR1310_PCIE2_CFG_DEVICE_PRESENT BIT(11) + #define SPEAR1310_PCIE2_CFG_POWERUP_RESET BIT(10) + #define SPEAR1310_PCIE2_CFG_CORE_CLK_EN BIT(9) + #define SPEAR1310_PCIE2_CFG_AUX_CLK_EN BIT(8) + #define SPEAR1310_PCIE1_CFG_DEVICE_PRESENT BIT(7) + #define SPEAR1310_PCIE1_CFG_POWERUP_RESET BIT(6) + #define SPEAR1310_PCIE1_CFG_CORE_CLK_EN BIT(5) + #define SPEAR1310_PCIE1_CFG_AUX_CLK_EN BIT(4) + #define SPEAR1310_PCIE0_CFG_DEVICE_PRESENT BIT(3) + #define SPEAR1310_PCIE0_CFG_POWERUP_RESET BIT(2) + #define SPEAR1310_PCIE0_CFG_CORE_CLK_EN BIT(1) + #define SPEAR1310_PCIE0_CFG_AUX_CLK_EN BIT(0) + + #define SPEAR1310_PCIE_CFG_MASK(x) ((0xF << (x * 4)) | BIT((x + 29))) + #define SPEAR1310_SATA_CFG_MASK(x) ((0xF << (x * 4 + 16)) | \ + BIT((x + 29))) + #define SPEAR1310_PCIE_CFG_VAL(x) \ + (SPEAR1310_PCIE_SATA##x##_SEL_PCIE | \ + SPEAR1310_PCIE##x##_CFG_AUX_CLK_EN | \ + SPEAR1310_PCIE##x##_CFG_CORE_CLK_EN | \ + SPEAR1310_PCIE##x##_CFG_POWERUP_RESET | \ + SPEAR1310_PCIE##x##_CFG_DEVICE_PRESENT) + #define SPEAR1310_SATA_CFG_VAL(x) \ + (SPEAR1310_PCIE_SATA##x##_SEL_SATA | \ + SPEAR1310_SATA##x##_CFG_PM_CLK_EN | \ + SPEAR1310_SATA##x##_CFG_POWERUP_RESET | \ + SPEAR1310_SATA##x##_CFG_RX_CLK_EN | \ + SPEAR1310_SATA##x##_CFG_TX_CLK_EN) + +#define SPEAR1310_PCIE_MIPHY_CFG_1 0x3A8 + #define SPEAR1310_MIPHY_DUAL_OSC_BYPASS_EXT BIT(31) + #define SPEAR1310_MIPHY_DUAL_CLK_REF_DIV2 BIT(28) + #define SPEAR1310_MIPHY_DUAL_PLL_RATIO_TOP(x) (x << 16) + #define SPEAR1310_MIPHY_SINGLE_OSC_BYPASS_EXT BIT(15) + #define SPEAR1310_MIPHY_SINGLE_CLK_REF_DIV2 BIT(12) + #define SPEAR1310_MIPHY_SINGLE_PLL_RATIO_TOP(x) (x << 0) + #define SPEAR1310_PCIE_SATA_MIPHY_CFG_SATA_MASK (0xFFFF) + #define SPEAR1310_PCIE_SATA_MIPHY_CFG_PCIE_MASK (0xFFFF << 16) + #define SPEAR1310_PCIE_SATA_MIPHY_CFG_SATA \ + (SPEAR1310_MIPHY_DUAL_OSC_BYPASS_EXT | \ + SPEAR1310_MIPHY_DUAL_CLK_REF_DIV2 | \ + SPEAR1310_MIPHY_DUAL_PLL_RATIO_TOP(60) | \ + SPEAR1310_MIPHY_SINGLE_OSC_BYPASS_EXT | \ + SPEAR1310_MIPHY_SINGLE_CLK_REF_DIV2 | \ + SPEAR1310_MIPHY_SINGLE_PLL_RATIO_TOP(60)) + #define SPEAR1310_PCIE_SATA_MIPHY_CFG_SATA_25M_CRYSTAL_CLK \ + (SPEAR1310_MIPHY_SINGLE_PLL_RATIO_TOP(120)) + #define SPEAR1310_PCIE_SATA_MIPHY_CFG_PCIE \ + (SPEAR1310_MIPHY_DUAL_OSC_BYPASS_EXT | \ + SPEAR1310_MIPHY_DUAL_PLL_RATIO_TOP(25) | \ + SPEAR1310_MIPHY_SINGLE_OSC_BYPASS_EXT | \ + SPEAR1310_MIPHY_SINGLE_PLL_RATIO_TOP(25)) + +#define SPEAR1310_PCIE_MIPHY_CFG_2 0x3AC + +enum spear1310_miphy_mode { + SATA, + PCIE, +}; + +struct spear1310_miphy_priv { + /* instance id of this phy */ + u32 id; + /* phy mode: 0 for SATA 1 for PCIe */ + enum spear1310_miphy_mode mode; + /* regmap for any soc specific misc registers */ + struct regmap *misc; + /* phy struct pointer */ + struct phy *phy; +}; + +static int spear1310_miphy_pcie_init(struct spear1310_miphy_priv *priv) +{ + u32 val; + + regmap_update_bits(priv->misc, SPEAR1310_PCIE_MIPHY_CFG_1, + SPEAR1310_PCIE_SATA_MIPHY_CFG_PCIE_MASK, + SPEAR1310_PCIE_SATA_MIPHY_CFG_PCIE); + + switch (priv->id) { + case 0: + val = SPEAR1310_PCIE_CFG_VAL(0); + break; + case 1: + val = SPEAR1310_PCIE_CFG_VAL(1); + break; + case 2: + val = SPEAR1310_PCIE_CFG_VAL(2); + break; + default: + return -EINVAL; + } + + regmap_update_bits(priv->misc, SPEAR1310_PCIE_SATA_CFG, + SPEAR1310_PCIE_CFG_MASK(priv->id), val); + + return 0; +} + +static int spear1310_miphy_pcie_exit(struct spear1310_miphy_priv *priv) +{ + regmap_update_bits(priv->misc, SPEAR1310_PCIE_SATA_CFG, + SPEAR1310_PCIE_CFG_MASK(priv->id), 0); + + regmap_update_bits(priv->misc, SPEAR1310_PCIE_MIPHY_CFG_1, + SPEAR1310_PCIE_SATA_MIPHY_CFG_PCIE_MASK, 0); + + return 0; +} + +static int spear1310_miphy_init(struct phy *phy) +{ + struct spear1310_miphy_priv *priv = phy_get_drvdata(phy); + int ret = 0; + + if (priv->mode == PCIE) + ret = spear1310_miphy_pcie_init(priv); + + return ret; +} + +static int spear1310_miphy_exit(struct phy *phy) +{ + struct spear1310_miphy_priv *priv = phy_get_drvdata(phy); + int ret = 0; + + if (priv->mode == PCIE) + ret = spear1310_miphy_pcie_exit(priv); + + return ret; +} + +static const struct of_device_id spear1310_miphy_of_match[] = { + { .compatible = "st,spear1310-miphy" }, + { }, +}; +MODULE_DEVICE_TABLE(of, spear1310_miphy_of_match); + +static struct phy_ops spear1310_miphy_ops = { + .init = spear1310_miphy_init, + .exit = spear1310_miphy_exit, + .owner = THIS_MODULE, +}; + +static struct phy *spear1310_miphy_xlate(struct device *dev, + struct of_phandle_args *args) +{ + struct spear1310_miphy_priv *priv = dev_get_drvdata(dev); + + if (args->args_count < 1) { + dev_err(dev, "DT did not pass correct no of args\n"); + return NULL; + } + + priv->mode = args->args[0]; + + if (priv->mode != SATA && priv->mode != PCIE) { + dev_err(dev, "DT did not pass correct phy mode\n"); + return NULL; + } + + return priv->phy; +} + +static int spear1310_miphy_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct spear1310_miphy_priv *priv; + struct phy_provider *phy_provider; + + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); + if (!priv) { + dev_err(dev, "can't alloc spear1310_miphy private date memory\n"); + return -ENOMEM; + } + + priv->misc = + syscon_regmap_lookup_by_phandle(dev->of_node, "misc"); + if (IS_ERR(priv->misc)) { + dev_err(dev, "failed to find misc regmap\n"); + return PTR_ERR(priv->misc); + } + + if (of_property_read_u32(dev->of_node, "phy-id", &priv->id)) { + dev_err(dev, "failed to find phy id\n"); + return -EINVAL; + } + + priv->phy = devm_phy_create(dev, &spear1310_miphy_ops, NULL); + if (IS_ERR(priv->phy)) { + dev_err(dev, "failed to create SATA PCIe PHY\n"); + return PTR_ERR(priv->phy); + } + + dev_set_drvdata(dev, priv); + phy_set_drvdata(priv->phy, priv); + + phy_provider = + devm_of_phy_provider_register(dev, spear1310_miphy_xlate); + if (IS_ERR(phy_provider)) { + dev_err(dev, "failed to register phy provider\n"); + return PTR_ERR(phy_provider); + } + + return 0; +} + +static struct platform_driver spear1310_miphy_driver = { + .probe = spear1310_miphy_probe, + .driver = { + .name = "spear1310-miphy", + .owner = THIS_MODULE, + .of_match_table = of_match_ptr(spear1310_miphy_of_match), + }, +}; + +static int __init spear1310_miphy_phy_init(void) +{ + return platform_driver_register(&spear1310_miphy_driver); +} +module_init(spear1310_miphy_phy_init); + +static void __exit spear1310_miphy_phy_exit(void) +{ + platform_driver_unregister(&spear1310_miphy_driver); +} +module_exit(spear1310_miphy_phy_exit); + +MODULE_DESCRIPTION("ST SPEAR1310-MIPHY driver"); +MODULE_AUTHOR("Pratyush Anand "); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/phy/phy-spear1340-miphy.c b/drivers/phy/phy-spear1340-miphy.c new file mode 100644 index 0000000000000..8de98adf21c36 --- /dev/null +++ b/drivers/phy/phy-spear1340-miphy.c @@ -0,0 +1,307 @@ +/* + * ST spear1340-miphy driver + * + * Copyright (C) 2014 ST Microelectronics + * Pratyush Anand + * Mohit Kumar + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include + +/* SPEAr1340 Registers */ +/* Power Management Registers */ +#define SPEAR1340_PCM_CFG 0x100 + #define SPEAR1340_PCM_CFG_SATA_POWER_EN BIT(11) +#define SPEAR1340_PCM_WKUP_CFG 0x104 +#define SPEAR1340_SWITCH_CTR 0x108 + +#define SPEAR1340_PERIP1_SW_RST 0x318 + #define SPEAR1340_PERIP1_SW_RSATA BIT(12) +#define SPEAR1340_PERIP2_SW_RST 0x31C +#define SPEAR1340_PERIP3_SW_RST 0x320 + +/* PCIE - SATA configuration registers */ +#define SPEAR1340_PCIE_SATA_CFG 0x424 + /* PCIE CFG MASks */ + #define SPEAR1340_PCIE_CFG_DEVICE_PRESENT BIT(11) + #define SPEAR1340_PCIE_CFG_POWERUP_RESET BIT(10) + #define SPEAR1340_PCIE_CFG_CORE_CLK_EN BIT(9) + #define SPEAR1340_PCIE_CFG_AUX_CLK_EN BIT(8) + #define SPEAR1340_SATA_CFG_TX_CLK_EN BIT(4) + #define SPEAR1340_SATA_CFG_RX_CLK_EN BIT(3) + #define SPEAR1340_SATA_CFG_POWERUP_RESET BIT(2) + #define SPEAR1340_SATA_CFG_PM_CLK_EN BIT(1) + #define SPEAR1340_PCIE_SATA_SEL_PCIE (0) + #define SPEAR1340_PCIE_SATA_SEL_SATA (1) + #define SPEAR1340_PCIE_SATA_CFG_MASK 0xF1F + #define SPEAR1340_PCIE_CFG_VAL (SPEAR1340_PCIE_SATA_SEL_PCIE | \ + SPEAR1340_PCIE_CFG_AUX_CLK_EN | \ + SPEAR1340_PCIE_CFG_CORE_CLK_EN | \ + SPEAR1340_PCIE_CFG_POWERUP_RESET | \ + SPEAR1340_PCIE_CFG_DEVICE_PRESENT) + #define SPEAR1340_SATA_CFG_VAL (SPEAR1340_PCIE_SATA_SEL_SATA | \ + SPEAR1340_SATA_CFG_PM_CLK_EN | \ + SPEAR1340_SATA_CFG_POWERUP_RESET | \ + SPEAR1340_SATA_CFG_RX_CLK_EN | \ + SPEAR1340_SATA_CFG_TX_CLK_EN) + +#define SPEAR1340_PCIE_MIPHY_CFG 0x428 + #define SPEAR1340_MIPHY_OSC_BYPASS_EXT BIT(31) + #define SPEAR1340_MIPHY_CLK_REF_DIV2 BIT(27) + #define SPEAR1340_MIPHY_CLK_REF_DIV4 (2 << 27) + #define SPEAR1340_MIPHY_CLK_REF_DIV8 (3 << 27) + #define SPEAR1340_MIPHY_PLL_RATIO_TOP(x) (x << 0) + #define SPEAR1340_PCIE_MIPHY_CFG_MASK 0xF80000FF + #define SPEAR1340_PCIE_SATA_MIPHY_CFG_SATA \ + (SPEAR1340_MIPHY_OSC_BYPASS_EXT | \ + SPEAR1340_MIPHY_CLK_REF_DIV2 | \ + SPEAR1340_MIPHY_PLL_RATIO_TOP(60)) + #define SPEAR1340_PCIE_SATA_MIPHY_CFG_SATA_25M_CRYSTAL_CLK \ + (SPEAR1340_MIPHY_PLL_RATIO_TOP(120)) + #define SPEAR1340_PCIE_SATA_MIPHY_CFG_PCIE \ + (SPEAR1340_MIPHY_OSC_BYPASS_EXT | \ + SPEAR1340_MIPHY_PLL_RATIO_TOP(25)) + +enum spear1340_miphy_mode { + SATA, + PCIE, +}; + +struct spear1340_miphy_priv { + /* phy mode: 0 for SATA 1 for PCIe */ + enum spear1340_miphy_mode mode; + /* regmap for any soc specific misc registers */ + struct regmap *misc; + /* phy struct pointer */ + struct phy *phy; +}; + +static int spear1340_miphy_sata_init(struct spear1340_miphy_priv *priv) +{ + regmap_update_bits(priv->misc, SPEAR1340_PCIE_SATA_CFG, + SPEAR1340_PCIE_SATA_CFG_MASK, + SPEAR1340_SATA_CFG_VAL); + regmap_update_bits(priv->misc, SPEAR1340_PCIE_MIPHY_CFG, + SPEAR1340_PCIE_MIPHY_CFG_MASK, + SPEAR1340_PCIE_SATA_MIPHY_CFG_SATA_25M_CRYSTAL_CLK); + /* Switch on sata power domain */ + regmap_update_bits(priv->misc, SPEAR1340_PCM_CFG, + SPEAR1340_PCM_CFG_SATA_POWER_EN, + SPEAR1340_PCM_CFG_SATA_POWER_EN); + /* Wait for SATA power domain on */ + msleep(20); + + /* Disable PCIE SATA Controller reset */ + regmap_update_bits(priv->misc, SPEAR1340_PERIP1_SW_RST, + SPEAR1340_PERIP1_SW_RSATA, 0); + /* Wait for SATA reset de-assert completion */ + msleep(20); + + return 0; +} + +static int spear1340_miphy_sata_exit(struct spear1340_miphy_priv *priv) +{ + regmap_update_bits(priv->misc, SPEAR1340_PCIE_SATA_CFG, + SPEAR1340_PCIE_SATA_CFG_MASK, 0); + regmap_update_bits(priv->misc, SPEAR1340_PCIE_MIPHY_CFG, + SPEAR1340_PCIE_MIPHY_CFG_MASK, 0); + + /* Enable PCIE SATA Controller reset */ + regmap_update_bits(priv->misc, SPEAR1340_PERIP1_SW_RST, + SPEAR1340_PERIP1_SW_RSATA, + SPEAR1340_PERIP1_SW_RSATA); + /* Wait for SATA power domain off */ + msleep(20); + /* Switch off sata power domain */ + regmap_update_bits(priv->misc, SPEAR1340_PCM_CFG, + SPEAR1340_PCM_CFG_SATA_POWER_EN, 0); + /* Wait for SATA reset assert completion */ + msleep(20); + + return 0; +} + +static int spear1340_miphy_pcie_init(struct spear1340_miphy_priv *priv) +{ + regmap_update_bits(priv->misc, SPEAR1340_PCIE_MIPHY_CFG, + SPEAR1340_PCIE_MIPHY_CFG_MASK, + SPEAR1340_PCIE_SATA_MIPHY_CFG_PCIE); + regmap_update_bits(priv->misc, SPEAR1340_PCIE_SATA_CFG, + SPEAR1340_PCIE_SATA_CFG_MASK, + SPEAR1340_PCIE_CFG_VAL); + + return 0; +} + +static int spear1340_miphy_pcie_exit(struct spear1340_miphy_priv *priv) +{ + regmap_update_bits(priv->misc, SPEAR1340_PCIE_MIPHY_CFG, + SPEAR1340_PCIE_MIPHY_CFG_MASK, 0); + regmap_update_bits(priv->misc, SPEAR1340_PCIE_SATA_CFG, + SPEAR1340_PCIE_SATA_CFG_MASK, 0); + + return 0; +} + +static int spear1340_miphy_init(struct phy *phy) +{ + struct spear1340_miphy_priv *priv = phy_get_drvdata(phy); + int ret = 0; + + if (priv->mode == SATA) + ret = spear1340_miphy_sata_init(priv); + else if (priv->mode == PCIE) + ret = spear1340_miphy_pcie_init(priv); + + return ret; +} + +static int spear1340_miphy_exit(struct phy *phy) +{ + struct spear1340_miphy_priv *priv = phy_get_drvdata(phy); + int ret = 0; + + if (priv->mode == SATA) + ret = spear1340_miphy_sata_exit(priv); + else if (priv->mode == PCIE) + ret = spear1340_miphy_pcie_exit(priv); + + return ret; +} + +static const struct of_device_id spear1340_miphy_of_match[] = { + { .compatible = "st,spear1340-miphy" }, + { }, +}; +MODULE_DEVICE_TABLE(of, spear1340_miphy_of_match); + +static struct phy_ops spear1340_miphy_ops = { + .init = spear1340_miphy_init, + .exit = spear1340_miphy_exit, + .owner = THIS_MODULE, +}; + +#ifdef CONFIG_PM_SLEEP +static int spear1340_miphy_suspend(struct device *dev) +{ + struct spear1340_miphy_priv *priv = dev_get_drvdata(dev); + int ret = 0; + + if (priv->mode == SATA) + ret = spear1340_miphy_sata_exit(priv); + + return ret; +} + +static int spear1340_miphy_resume(struct device *dev) +{ + struct spear1340_miphy_priv *priv = dev_get_drvdata(dev); + int ret = 0; + + if (priv->mode == SATA) + ret = spear1340_miphy_sata_init(priv); + + return ret; +} +#endif + +static SIMPLE_DEV_PM_OPS(spear1340_miphy_pm_ops, spear1340_miphy_suspend, + spear1340_miphy_resume); + +static struct phy *spear1340_miphy_xlate(struct device *dev, + struct of_phandle_args *args) +{ + struct spear1340_miphy_priv *priv = dev_get_drvdata(dev); + + if (args->args_count < 1) { + dev_err(dev, "DT did not pass correct no of args\n"); + return NULL; + } + + priv->mode = args->args[0]; + + if (priv->mode != SATA && priv->mode != PCIE) { + dev_err(dev, "DT did not pass correct phy mode\n"); + return NULL; + } + + return priv->phy; +} + +static int spear1340_miphy_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct spear1340_miphy_priv *priv; + struct phy_provider *phy_provider; + + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); + if (!priv) { + dev_err(dev, "can't alloc spear1340_miphy private date memory\n"); + return -ENOMEM; + } + + priv->misc = + syscon_regmap_lookup_by_phandle(dev->of_node, "misc"); + if (IS_ERR(priv->misc)) { + dev_err(dev, "failed to find misc regmap\n"); + return PTR_ERR(priv->misc); + } + + priv->phy = devm_phy_create(dev, &spear1340_miphy_ops, NULL); + if (IS_ERR(priv->phy)) { + dev_err(dev, "failed to create SATA PCIe PHY\n"); + return PTR_ERR(priv->phy); + } + + dev_set_drvdata(dev, priv); + phy_set_drvdata(priv->phy, priv); + + phy_provider = + devm_of_phy_provider_register(dev, spear1340_miphy_xlate); + if (IS_ERR(phy_provider)) { + dev_err(dev, "failed to register phy provider\n"); + return PTR_ERR(phy_provider); + } + + return 0; +} + +static struct platform_driver spear1340_miphy_driver = { + .probe = spear1340_miphy_probe, + .driver = { + .name = "spear1340-miphy", + .owner = THIS_MODULE, + .pm = &spear1340_miphy_pm_ops, + .of_match_table = of_match_ptr(spear1340_miphy_of_match), + }, +}; + +static int __init spear1340_miphy_phy_init(void) +{ + return platform_driver_register(&spear1340_miphy_driver); +} +module_init(spear1340_miphy_phy_init); + +static void __exit spear1340_miphy_phy_exit(void) +{ + platform_driver_unregister(&spear1340_miphy_driver); +} +module_exit(spear1340_miphy_phy_exit); + +MODULE_DESCRIPTION("ST SPEAR1340-MIPHY driver"); +MODULE_AUTHOR("Pratyush Anand "); +MODULE_LICENSE("GPL v2");