diff --git a/arch/arm/mach-sa1100/Kconfig b/arch/arm/mach-sa1100/Kconfig
index 07df3a59b13fc..fde7ef1ab192f 100644
--- a/arch/arm/mach-sa1100/Kconfig
+++ b/arch/arm/mach-sa1100/Kconfig
@@ -6,6 +6,8 @@ config SA1100_ASSABET
 	bool "Assabet"
 	select ARM_SA1110_CPUFREQ
 	select GPIO_REG
+	select REGULATOR
+	select REGULATOR_FIXED_VOLTAGE
 	help
 	  Say Y here if you are using the Intel(R) StrongARM(R) SA-1110
 	  Microprocessor Development Board (also known as the Assabet).
@@ -137,6 +139,8 @@ config SA1100_PLEB
 config SA1100_SHANNON
 	bool "Shannon"
 	select ARM_SA1100_CPUFREQ
+	select REGULATOR
+	select REGULATOR_FIXED_VOLTAGE
 	help
 	  The Shannon (also known as a Tuxscreen, and also as a IS2630) was a
 	  limited edition webphone produced by Philips. The Shannon is a SA1100
diff --git a/arch/arm/mach-sa1100/assabet.c b/arch/arm/mach-sa1100/assabet.c
index f68241d995f24..575ec085cffaf 100644
--- a/arch/arm/mach-sa1100/assabet.c
+++ b/arch/arm/mach-sa1100/assabet.c
@@ -14,8 +14,11 @@
 #include <linux/module.h>
 #include <linux/errno.h>
 #include <linux/gpio/gpio-reg.h>
+#include <linux/gpio/machine.h>
 #include <linux/ioport.h>
 #include <linux/platform_data/sa11x0-serial.h>
+#include <linux/regulator/fixed.h>
+#include <linux/regulator/machine.h>
 #include <linux/serial_core.h>
 #include <linux/platform_device.h>
 #include <linux/mfd/ucb1x00.h>
@@ -445,6 +448,29 @@ static struct resource neponset_resources[] = {
 };
 #endif
 
+static struct gpiod_lookup_table assabet_cf_gpio_table = {
+	.dev_id = "sa11x0-pcmcia.1",
+	.table = {
+		GPIO_LOOKUP("gpio", 21, "ready", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("gpio", 22, "detect", GPIO_ACTIVE_LOW),
+		GPIO_LOOKUP("gpio", 24, "bvd2", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("gpio", 25, "bvd1", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("assabet", 1, "reset", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("assabet", 7, "bus-enable", GPIO_ACTIVE_LOW),
+		{ },
+	},
+};
+
+static struct regulator_consumer_supply assabet_cf_vcc_consumers[] = {
+	REGULATOR_SUPPLY("vcc", "sa11x0-pcmcia.1"),
+};
+
+static struct fixed_voltage_config assabet_cf_vcc_pdata __initdata = {
+	.supply_name = "cf-power",
+	.microvolts = 3300000,
+	.enable_high = 1,
+};
+
 static void __init assabet_init(void)
 {
 	/*
@@ -490,6 +516,11 @@ static void __init assabet_init(void)
 		platform_device_register_simple("neponset", 0,
 			neponset_resources, ARRAY_SIZE(neponset_resources));
 #endif
+	} else {
+		sa11x0_register_fixed_regulator(0, &assabet_cf_vcc_pdata,
+					 assabet_cf_vcc_consumers,
+					 ARRAY_SIZE(assabet_cf_vcc_consumers));
+
 	}
 
 #ifndef ASSABET_PAL_VIDEO
@@ -501,6 +532,9 @@ static void __init assabet_init(void)
 			    ARRAY_SIZE(assabet_flash_resources));
 	sa11x0_register_irda(&assabet_irda_data);
 	sa11x0_register_mcp(&assabet_mcp_data);
+
+	if (!machine_has_neponset())
+		sa11x0_register_pcmcia(1, &assabet_cf_gpio_table);
 }
 
 /*
@@ -768,6 +802,7 @@ fs_initcall(assabet_leds_init);
 
 void __init assabet_init_irq(void)
 {
+	unsigned int assabet_gpio_base;
 	u32 def_val;
 
 	sa1100_init_irq();
@@ -782,7 +817,9 @@ void __init assabet_init_irq(void)
 	 *
 	 * This must precede any driver calls to BCR_set() or BCR_clear().
 	 */
-	assabet_init_gpio((void *)&ASSABET_BCR, def_val);
+	assabet_gpio_base = assabet_init_gpio((void *)&ASSABET_BCR, def_val);
+
+	assabet_cf_vcc_pdata.gpio = assabet_gpio_base + 0;
 }
 
 MACHINE_START(ASSABET, "Intel-Assabet")
diff --git a/arch/arm/mach-sa1100/cerf.c b/arch/arm/mach-sa1100/cerf.c
index 2d25ececb415a..b2a4b41626efb 100644
--- a/arch/arm/mach-sa1100/cerf.c
+++ b/arch/arm/mach-sa1100/cerf.c
@@ -11,6 +11,7 @@
  */
 
 #include <linux/init.h>
+#include <linux/gpio/machine.h>
 #include <linux/kernel.h>
 #include <linux/tty.h>
 #include <linux/platform_data/sa11x0-serial.h>
@@ -45,6 +46,19 @@ static struct platform_device cerfuart2_device = {
 	.resource	= cerfuart2_resources,
 };
 
+/* Compact Flash */
+static struct gpiod_lookup_table cerf_cf_gpio_table = {
+	.dev_id = "sa11x0-pcmcia.1",
+	.table = {
+		GPIO_LOOKUP("gpio", 19, "bvd2", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("gpio", 20, "bvd1", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("gpio", 21, "reset", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("gpio", 22, "ready", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("gpio", 23, "detect", GPIO_ACTIVE_LOW),
+		{ },
+	},
+};
+
 /* LEDs */
 struct gpio_led cerf_gpio_leds[] = {
 	{
@@ -151,9 +165,6 @@ static void __init cerf_map_io(void)
 	sa1100_register_uart(0, 3);
 	sa1100_register_uart(1, 2); /* disable this and the uart2 device for sa1100_fir */
 	sa1100_register_uart(2, 1);
-
-	/* set some GPDR bits here while it's safe */
-	GPDR |= CERF_GPIO_CF_RESET;
 }
 
 static struct mcp_plat_data cerf_mcp_data = {
@@ -167,6 +178,7 @@ static void __init cerf_init(void)
 	platform_add_devices(cerf_devices, ARRAY_SIZE(cerf_devices));
 	sa11x0_register_mtd(&cerf_flash_data, &cerf_flash_resource, 1);
 	sa11x0_register_mcp(&cerf_mcp_data);
+	sa11x0_register_pcmcia(1, &cerf_cf_gpio_table);
 }
 
 MACHINE_START(CERF, "Intrinsyc CerfBoard/CerfCube")
diff --git a/arch/arm/mach-sa1100/clock.c b/arch/arm/mach-sa1100/clock.c
index b2eb3d232e398..6199e87447ca6 100644
--- a/arch/arm/mach-sa1100/clock.c
+++ b/arch/arm/mach-sa1100/clock.c
@@ -163,6 +163,8 @@ static struct clk_lookup sa11xx_clkregs[] = {
 	CLKDEV_INIT("sa1100-rtc", NULL, NULL),
 	CLKDEV_INIT("sa11x0-fb", NULL, &clk_cpu),
 	CLKDEV_INIT("sa11x0-pcmcia", NULL, &clk_cpu),
+	CLKDEV_INIT("sa11x0-pcmcia.0", NULL, &clk_cpu),
+	CLKDEV_INIT("sa11x0-pcmcia.1", NULL, &clk_cpu),
 	/* sa1111 names devices using internal offsets, PCMCIA is at 0x1800 */
 	CLKDEV_INIT("1800", NULL, &clk_cpu),
 	CLKDEV_INIT(NULL, "OSTIMER0", &clk_36864),
diff --git a/arch/arm/mach-sa1100/generic.c b/arch/arm/mach-sa1100/generic.c
index 2eb00691b07db..7167ddf84a0ee 100644
--- a/arch/arm/mach-sa1100/generic.c
+++ b/arch/arm/mach-sa1100/generic.c
@@ -10,6 +10,7 @@
  * published by the Free Software Foundation.
  */
 #include <linux/gpio.h>
+#include <linux/gpio/machine.h>
 #include <linux/module.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
@@ -20,6 +21,8 @@
 #include <linux/ioport.h>
 #include <linux/platform_device.h>
 #include <linux/reboot.h>
+#include <linux/regulator/fixed.h>
+#include <linux/regulator/machine.h>
 #include <linux/irqchip/irq-sa11x0.h>
 
 #include <video/sa1100fb.h>
@@ -232,11 +235,20 @@ void sa11x0_register_lcd(struct sa1100fb_mach_info *inf)
 	sa11x0_register_device(&sa11x0fb_device, inf);
 }
 
+static bool sa11x0pcmcia_legacy = true;
 static struct platform_device sa11x0pcmcia_device = {
 	.name		= "sa11x0-pcmcia",
 	.id		= -1,
 };
 
+void sa11x0_register_pcmcia(int socket, struct gpiod_lookup_table *table)
+{
+	if (table)
+		gpiod_add_lookup_table(table);
+	platform_device_register_simple("sa11x0-pcmcia", socket, NULL, 0);
+	sa11x0pcmcia_legacy = false;
+}
+
 static struct platform_device sa11x0mtd_device = {
 	.name		= "sa1100-mtd",
 	.id		= -1,
@@ -311,7 +323,6 @@ static struct platform_device *sa11x0_devices[] __initdata = {
 	&sa11x0uart1_device,
 	&sa11x0uart3_device,
 	&sa11x0ssp_device,
-	&sa11x0pcmcia_device,
 	&sa11x0rtc_device,
 	&sa11x0dma_device,
 };
@@ -319,6 +330,12 @@ static struct platform_device *sa11x0_devices[] __initdata = {
 static int __init sa1100_init(void)
 {
 	pm_power_off = sa1100_power_off;
+
+	if (sa11x0pcmcia_legacy)
+		platform_device_register(&sa11x0pcmcia_device);
+
+	regulator_has_full_constraints();
+
 	return platform_add_devices(sa11x0_devices, ARRAY_SIZE(sa11x0_devices));
 }
 
@@ -329,6 +346,31 @@ void __init sa11x0_init_late(void)
 	sa11x0_pm_init();
 }
 
+int __init sa11x0_register_fixed_regulator(int n,
+	struct fixed_voltage_config *cfg,
+	struct regulator_consumer_supply *supplies, unsigned num_supplies)
+{
+	struct regulator_init_data *id;
+
+	cfg->init_data = id = kzalloc(sizeof(*cfg->init_data), GFP_KERNEL);
+	if (!cfg->init_data)
+		return -ENOMEM;
+
+	if (cfg->gpio < 0)
+		id->constraints.always_on = 1;
+	id->constraints.name = cfg->supply_name;
+	id->constraints.min_uV = cfg->microvolts;
+	id->constraints.max_uV = cfg->microvolts;
+	id->constraints.valid_modes_mask = REGULATOR_MODE_NORMAL;
+	id->constraints.valid_ops_mask = REGULATOR_CHANGE_STATUS;
+	id->consumer_supplies = supplies;
+	id->num_consumer_supplies = num_supplies;
+
+	platform_device_register_resndata(NULL, "reg-fixed-voltage", n,
+					  NULL, 0, cfg, sizeof(*cfg));
+	return 0;
+}
+
 /*
  * Common I/O mapping:
  *
diff --git a/arch/arm/mach-sa1100/generic.h b/arch/arm/mach-sa1100/generic.h
index 97502922a15d6..5f3cb52fa6ab1 100644
--- a/arch/arm/mach-sa1100/generic.h
+++ b/arch/arm/mach-sa1100/generic.h
@@ -47,3 +47,11 @@ static inline int sa11x0_pm_init(void) { return 0; }
 #endif
 
 int sa11xx_clk_init(void);
+
+struct gpiod_lookup_table;
+void sa11x0_register_pcmcia(int socket, struct gpiod_lookup_table *);
+
+struct fixed_voltage_config;
+struct regulator_consumer_supply;
+int sa11x0_register_fixed_regulator(int n, struct fixed_voltage_config *cfg,
+	struct regulator_consumer_supply *supplies, unsigned num_supplies);
diff --git a/arch/arm/mach-sa1100/h3xxx.c b/arch/arm/mach-sa1100/h3xxx.c
index b69e76614d5ba..36a78b0c106fc 100644
--- a/arch/arm/mach-sa1100/h3xxx.c
+++ b/arch/arm/mach-sa1100/h3xxx.c
@@ -11,6 +11,7 @@
  */
 
 #include <linux/kernel.h>
+#include <linux/gpio/machine.h>
 #include <linux/gpio.h>
 #include <linux/gpio_keys.h>
 #include <linux/input.h>
@@ -264,8 +265,24 @@ static struct platform_device *h3xxx_devices[] = {
 	&h3xxx_micro_asic,
 };
 
+static struct gpiod_lookup_table h3xxx_pcmcia_gpio_table = {
+	.dev_id = "sa11x0-pcmcia",
+	.table = {
+		GPIO_LOOKUP("gpio", H3XXX_GPIO_PCMCIA_CD0,
+			    "pcmcia0-detect", GPIO_ACTIVE_LOW),
+		GPIO_LOOKUP("gpio", H3XXX_GPIO_PCMCIA_IRQ0,
+			    "pcmcia0-ready", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("gpio", H3XXX_GPIO_PCMCIA_CD1,
+			    "pcmcia1-detect", GPIO_ACTIVE_LOW),
+		GPIO_LOOKUP("gpio", H3XXX_GPIO_PCMCIA_IRQ1,
+			    "pcmcia1-ready", GPIO_ACTIVE_HIGH),
+		{ },
+	},
+};
+
 void __init h3xxx_mach_init(void)
 {
+	gpiod_add_lookup_table(&h3xxx_pcmcia_gpio_table);
 	sa1100_register_uart_fns(&h3xxx_port_fns);
 	sa11x0_register_mtd(&h3xxx_flash_data, &h3xxx_flash_resource, 1);
 	platform_add_devices(h3xxx_devices, ARRAY_SIZE(h3xxx_devices));
diff --git a/arch/arm/mach-sa1100/include/mach/assabet.h b/arch/arm/mach-sa1100/include/mach/assabet.h
index 558b45323a2d6..641a961653af6 100644
--- a/arch/arm/mach-sa1100/include/mach/assabet.h
+++ b/arch/arm/mach-sa1100/include/mach/assabet.h
@@ -96,10 +96,4 @@ extern void assabet_uda1341_reset(int set);
 #define ASSABET_GPIO_BATT_LOW		GPIO_GPIO (26)	/* Low battery */
 #define ASSABET_GPIO_RCLK		GPIO_GPIO (26)	/* CCLK/2  */
 
-/* These are gpiolib GPIO numbers, not bitmasks */
-#define ASSABET_GPIO_CF_IRQ		21	/* CF IRQ */
-#define ASSABET_GPIO_CF_CD		22	/* CF CD  */
-#define ASSABET_GPIO_CF_BVD2		24	/* CF BVD / IOSPKR */
-#define ASSABET_GPIO_CF_BVD1		25	/* CF BVD / IOSTSCHG */
-
 #endif
diff --git a/arch/arm/mach-sa1100/nanoengine.c b/arch/arm/mach-sa1100/nanoengine.c
index f1cb3784d525d..4d35258a7b32b 100644
--- a/arch/arm/mach-sa1100/nanoengine.c
+++ b/arch/arm/mach-sa1100/nanoengine.c
@@ -12,6 +12,7 @@
  */
 
 #include <linux/init.h>
+#include <linux/gpio/machine.h>
 #include <linux/kernel.h>
 #include <linux/platform_data/sa11x0-serial.h>
 #include <linux/mtd/mtd.h>
@@ -99,8 +100,30 @@ static void __init nanoengine_map_io(void)
 	Ser2HSCR0 = 0;
 }
 
+static struct gpiod_lookup_table nanoengine_pcmcia0_gpio_table = {
+	.dev_id = "sa11x0-pcmcia.0",
+	.table = {
+		GPIO_LOOKUP("gpio", 11, "ready", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("gpio", 13, "detect", GPIO_ACTIVE_LOW),
+		GPIO_LOOKUP("gpio", 15, "reset", GPIO_ACTIVE_HIGH),
+		{ },
+	},
+};
+
+static struct gpiod_lookup_table nanoengine_pcmcia1_gpio_table = {
+	.dev_id = "sa11x0-pcmcia.1",
+	.table = {
+		GPIO_LOOKUP("gpio", 12, "ready", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("gpio", 14, "detect", GPIO_ACTIVE_LOW),
+		GPIO_LOOKUP("gpio", 16, "reset", GPIO_ACTIVE_HIGH),
+		{ },
+	},
+};
+
 static void __init nanoengine_init(void)
 {
+	sa11x0_register_pcmcia(0, &nanoengine_pcmcia0_gpio_table);
+	sa11x0_register_pcmcia(1, &nanoengine_pcmcia1_gpio_table);
 	sa11x0_register_mtd(&nanoengine_flash_data, nanoengine_flash_resources,
 		ARRAY_SIZE(nanoengine_flash_resources));
 }
diff --git a/arch/arm/mach-sa1100/shannon.c b/arch/arm/mach-sa1100/shannon.c
index 856664c783d93..22f7fe0b809fd 100644
--- a/arch/arm/mach-sa1100/shannon.c
+++ b/arch/arm/mach-sa1100/shannon.c
@@ -5,11 +5,14 @@
 
 #include <linux/init.h>
 #include <linux/device.h>
+#include <linux/gpio/machine.h>
 #include <linux/kernel.h>
 #include <linux/platform_data/sa11x0-serial.h>
 #include <linux/tty.h>
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/partitions.h>
+#include <linux/regulator/fixed.h>
+#include <linux/regulator/machine.h>
 
 #include <video/sa1100fb.h>
 
@@ -72,8 +75,43 @@ static struct sa1100fb_mach_info shannon_lcd_info = {
 	.lccr3		= LCCR3_ACBsDiv(512),
 };
 
+static struct gpiod_lookup_table shannon_pcmcia0_gpio_table = {
+	.dev_id = "sa11x0-pcmcia.0",
+	.table = {
+		GPIO_LOOKUP("gpio", 24, "detect", GPIO_ACTIVE_LOW),
+		GPIO_LOOKUP("gpio", 26, "ready", GPIO_ACTIVE_HIGH),
+		{ },
+	},
+};
+
+static struct gpiod_lookup_table shannon_pcmcia1_gpio_table = {
+	.dev_id = "sa11x0-pcmcia.1",
+	.table = {
+		GPIO_LOOKUP("gpio", 25, "detect", GPIO_ACTIVE_LOW),
+		GPIO_LOOKUP("gpio", 27, "ready", GPIO_ACTIVE_HIGH),
+		{ },
+	},
+};
+
+static struct regulator_consumer_supply shannon_cf_vcc_consumers[] = {
+	REGULATOR_SUPPLY("vcc", "sa11x0-pcmcia.0"),
+	REGULATOR_SUPPLY("vcc", "sa11x0-pcmcia.1"),
+};
+
+static struct fixed_voltage_config shannon_cf_vcc_pdata __initdata = {
+	.supply_name = "cf-power",
+	.microvolts = 3300000,
+	.enabled_at_boot = 1,
+	.gpio = -EINVAL,
+};
+
 static void __init shannon_init(void)
 {
+	sa11x0_register_fixed_regulator(0, &shannon_cf_vcc_pdata,
+					shannon_cf_vcc_consumers,
+					ARRAY_SIZE(shannon_cf_vcc_consumers));
+	sa11x0_register_pcmcia(0, &shannon_pcmcia0_gpio_table);
+	sa11x0_register_pcmcia(1, &shannon_pcmcia1_gpio_table);
 	sa11x0_ppc_configure_mcp();
 	sa11x0_register_lcd(&shannon_lcd_info);
 	sa11x0_register_mtd(&shannon_flash_data, &shannon_flash_resource, 1);
diff --git a/arch/arm/mach-sa1100/simpad.c b/arch/arm/mach-sa1100/simpad.c
index 7d4feb8a49ac5..ace010479eb6c 100644
--- a/arch/arm/mach-sa1100/simpad.c
+++ b/arch/arm/mach-sa1100/simpad.c
@@ -4,6 +4,7 @@
  */
 
 #include <linux/module.h>
+#include <linux/gpio/machine.h>
 #include <linux/init.h>
 #include <linux/kernel.h>
 #include <linux/tty.h>
@@ -364,6 +365,15 @@ static struct platform_device *devices[] __initdata = {
 	&simpad_i2c,
 };
 
+/* Compact Flash */
+static struct gpiod_lookup_table simpad_cf_gpio_table = {
+	.dev_id = "sa11x0-pcmcia",
+	.table = {
+		GPIO_LOOKUP("gpio", GPIO_CF_IRQ, "cf-ready", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("gpio", GPIO_CF_CD, "cf-detect", GPIO_ACTIVE_HIGH),
+		{ },
+	},
+};
 
 
 static int __init simpad_init(void)
@@ -385,6 +395,7 @@ static int __init simpad_init(void)
 
 	pm_power_off = simpad_power_off;
 
+	sa11x0_register_pcmcia(-1, &simpad_cf_gpio_table);
 	sa11x0_ppc_configure_mcp();
 	sa11x0_register_mtd(&simpad_flash_data, simpad_flash_resources,
 			      ARRAY_SIZE(simpad_flash_resources));
diff --git a/drivers/pcmcia/Makefile b/drivers/pcmcia/Makefile
index f1f89ddb1bfd9..28502bd159e07 100644
--- a/drivers/pcmcia/Makefile
+++ b/drivers/pcmcia/Makefile
@@ -43,13 +43,9 @@ sa1111_cs-$(CONFIG_SA1100_JORNADA720)		+= sa1111_jornada720.o
 sa1111_cs-$(CONFIG_ARCH_LUBBOCK)		+= sa1111_lubbock.o
 
 sa1100_cs-y					+= sa1100_generic.o
-sa1100_cs-$(CONFIG_SA1100_ASSABET)		+= sa1100_assabet.o
-sa1100_cs-$(CONFIG_SA1100_CERF)			+= sa1100_cerf.o
 sa1100_cs-$(CONFIG_SA1100_COLLIE)		+= pxa2xx_sharpsl.o
 sa1100_cs-$(CONFIG_SA1100_H3100)		+= sa1100_h3600.o
 sa1100_cs-$(CONFIG_SA1100_H3600)		+= sa1100_h3600.o
-sa1100_cs-$(CONFIG_SA1100_NANOENGINE)		+= sa1100_nanoengine.o
-sa1100_cs-$(CONFIG_SA1100_SHANNON)		+= sa1100_shannon.o
 sa1100_cs-$(CONFIG_SA1100_SIMPAD)		+= sa1100_simpad.o
 
 pxa2xx_cm_x2xx_cs-y				+= pxa2xx_cm_x2xx.o pxa2xx_cm_x255.o pxa2xx_cm_x270.o
diff --git a/drivers/pcmcia/sa1100_assabet.c b/drivers/pcmcia/sa1100_assabet.c
deleted file mode 100644
index 78ad2bba76db0..0000000000000
--- a/drivers/pcmcia/sa1100_assabet.c
+++ /dev/null
@@ -1,100 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * drivers/pcmcia/sa1100_assabet.c
- *
- * PCMCIA implementation routines for Assabet
- *
- */
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/errno.h>
-#include <linux/interrupt.h>
-#include <linux/device.h>
-#include <linux/init.h>
-#include <linux/gpio.h>
-
-#include <asm/mach-types.h>
-#include <mach/assabet.h>
-
-#include "sa1100_generic.h"
-
-static int assabet_pcmcia_hw_init(struct soc_pcmcia_socket *skt)
-{
-	skt->stat[SOC_STAT_CD].gpio = ASSABET_GPIO_CF_CD;
-	skt->stat[SOC_STAT_CD].name = "CF CD";
-	skt->stat[SOC_STAT_BVD1].gpio = ASSABET_GPIO_CF_BVD1;
-	skt->stat[SOC_STAT_BVD1].name = "CF BVD1";
-	skt->stat[SOC_STAT_BVD2].gpio = ASSABET_GPIO_CF_BVD2;
-	skt->stat[SOC_STAT_BVD2].name = "CF BVD2";
-	skt->stat[SOC_STAT_RDY].gpio = ASSABET_GPIO_CF_IRQ;
-	skt->stat[SOC_STAT_RDY].name = "CF RDY";
-
-	return 0;
-}
-
-static int
-assabet_pcmcia_configure_socket(struct soc_pcmcia_socket *skt, const socket_state_t *state)
-{
-	unsigned int mask;
-
-	switch (state->Vcc) {
-	case 0:
-		mask = 0;
-		break;
-
-	case 50:
-		printk(KERN_WARNING "%s(): CS asked for 5V, applying 3.3V...\n",
-			__func__);
-
-	case 33:  /* Can only apply 3.3V to the CF slot. */
-		mask = ASSABET_BCR_CF_PWR;
-		break;
-
-	default:
-		printk(KERN_ERR "%s(): unrecognized Vcc %u\n", __func__,
-			state->Vcc);
-		return -1;
-	}
-
-	/* Silently ignore Vpp, speaker enable. */
-
-	if (state->flags & SS_RESET)
-		mask |= ASSABET_BCR_CF_RST;
-	if (!(state->flags & SS_OUTPUT_ENA))
-		mask |= ASSABET_BCR_CF_BUS_OFF;
-
-	ASSABET_BCR_frob(ASSABET_BCR_CF_RST | ASSABET_BCR_CF_PWR |
-			ASSABET_BCR_CF_BUS_OFF, mask);
-
-	return 0;
-}
-
-/*
- * Disable card status IRQs on suspend.
- */
-static void assabet_pcmcia_socket_suspend(struct soc_pcmcia_socket *skt)
-{
-	/*
-	 * Tristate the CF bus signals.  Also assert CF
-	 * reset as per user guide page 4-11.
-	 */
-	ASSABET_BCR_set(ASSABET_BCR_CF_BUS_OFF | ASSABET_BCR_CF_RST);
-}
-
-static struct pcmcia_low_level assabet_pcmcia_ops = { 
-	.owner			= THIS_MODULE,
-	.hw_init		= assabet_pcmcia_hw_init,
-	.socket_state		= soc_common_cf_socket_state,
-	.configure_socket	= assabet_pcmcia_configure_socket,
-	.socket_suspend		= assabet_pcmcia_socket_suspend,
-};
-
-int pcmcia_assabet_init(struct device *dev)
-{
-	int ret = -ENODEV;
-
-	if (machine_is_assabet() && !machine_has_neponset())
-		ret = sa11xx_drv_pcmcia_probe(dev, &assabet_pcmcia_ops, 1, 1);
-
-	return ret;
-}
diff --git a/drivers/pcmcia/sa1100_cerf.c b/drivers/pcmcia/sa1100_cerf.c
deleted file mode 100644
index 2a54081d161d4..0000000000000
--- a/drivers/pcmcia/sa1100_cerf.c
+++ /dev/null
@@ -1,86 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * drivers/pcmcia/sa1100_cerf.c
- *
- * PCMCIA implementation routines for CerfBoard
- * Based off the Assabet.
- *
- */
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/device.h>
-#include <linux/init.h>
-#include <linux/delay.h>
-#include <linux/gpio.h>
-
-#include <mach/hardware.h>
-#include <asm/mach-types.h>
-#include <asm/irq.h>
-#include <mach/cerf.h>
-#include "sa1100_generic.h"
-
-#define CERF_SOCKET	1
-
-static int cerf_pcmcia_hw_init(struct soc_pcmcia_socket *skt)
-{
-	int ret;
-
-	ret = gpio_request_one(CERF_GPIO_CF_RESET, GPIOF_OUT_INIT_LOW, "CF_RESET");
-	if (ret)
-		return ret;
-
-	skt->stat[SOC_STAT_CD].gpio = CERF_GPIO_CF_CD;
-	skt->stat[SOC_STAT_CD].name = "CF_CD";
-	skt->stat[SOC_STAT_BVD1].gpio = CERF_GPIO_CF_BVD1;
-	skt->stat[SOC_STAT_BVD1].name = "CF_BVD1";
-	skt->stat[SOC_STAT_BVD2].gpio = CERF_GPIO_CF_BVD2;
-	skt->stat[SOC_STAT_BVD2].name = "CF_BVD2";
-	skt->stat[SOC_STAT_RDY].gpio = CERF_GPIO_CF_IRQ;
-	skt->stat[SOC_STAT_RDY].name = "CF_IRQ";
-
-	return 0;
-}
-
-static void cerf_pcmcia_hw_shutdown(struct soc_pcmcia_socket *skt)
-{
-	gpio_free(CERF_GPIO_CF_RESET);
-}
-
-static int
-cerf_pcmcia_configure_socket(struct soc_pcmcia_socket *skt,
-			     const socket_state_t *state)
-{
-	switch (state->Vcc) {
-	case 0:
-	case 50:
-	case 33:
-		break;
-
-	default:
-		printk(KERN_ERR "%s(): unrecognized Vcc %u\n",
-			__func__, state->Vcc);
-		return -1;
-	}
-
-	gpio_set_value(CERF_GPIO_CF_RESET, !!(state->flags & SS_RESET));
-
-	return 0;
-}
-
-static struct pcmcia_low_level cerf_pcmcia_ops = { 
-	.owner			= THIS_MODULE,
-	.hw_init		= cerf_pcmcia_hw_init,
-	.hw_shutdown		= cerf_pcmcia_hw_shutdown,
-	.socket_state		= soc_common_cf_socket_state,
-	.configure_socket	= cerf_pcmcia_configure_socket,
-};
-
-int pcmcia_cerf_init(struct device *dev)
-{
-	int ret = -ENODEV;
-
-	if (machine_is_cerf())
-		ret = sa11xx_drv_pcmcia_probe(dev, &cerf_pcmcia_ops, CERF_SOCKET, 1);
-
-	return ret;
-}
diff --git a/drivers/pcmcia/sa1100_generic.c b/drivers/pcmcia/sa1100_generic.c
index 66acdc85727cc..47b060c574186 100644
--- a/drivers/pcmcia/sa1100_generic.c
+++ b/drivers/pcmcia/sa1100_generic.c
@@ -31,7 +31,9 @@
 ======================================================================*/
 
 #include <linux/module.h>
+#include <linux/gpio/consumer.h>
 #include <linux/init.h>
+#include <linux/regulator/consumer.h>
 #include <linux/slab.h>
 #include <linux/platform_device.h>
 
@@ -41,24 +43,64 @@
 
 #include "sa1100_generic.h"
 
+static const char *sa11x0_cf_gpio_names[] = {
+	[SOC_STAT_CD] = "detect",
+	[SOC_STAT_BVD1] = "bvd1",
+	[SOC_STAT_BVD2] = "bvd2",
+	[SOC_STAT_RDY] = "ready",
+};
+
+static int sa11x0_cf_hw_init(struct soc_pcmcia_socket *skt)
+{
+	struct device *dev = skt->socket.dev.parent;
+	int i;
+
+	skt->gpio_reset = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH);
+	if (IS_ERR(skt->gpio_reset))
+		return PTR_ERR(skt->gpio_reset);
+
+	skt->gpio_bus_enable = devm_gpiod_get_optional(dev, "bus-enable",
+						       GPIOD_OUT_HIGH);
+	if (IS_ERR(skt->gpio_bus_enable))
+		return PTR_ERR(skt->gpio_bus_enable);
+
+	skt->vcc.reg = devm_regulator_get_optional(dev, "vcc");
+	if (IS_ERR(skt->vcc.reg))
+		return PTR_ERR(skt->vcc.reg);
+
+	if (!skt->vcc.reg)
+		dev_warn(dev,
+			 "no Vcc regulator provided, ignoring Vcc controls\n");
+
+	for (i = 0; i < ARRAY_SIZE(sa11x0_cf_gpio_names); i++) {
+		skt->stat[i].name = sa11x0_cf_gpio_names[i];
+		skt->stat[i].desc = devm_gpiod_get_optional(dev,
+					sa11x0_cf_gpio_names[i], GPIOD_IN);
+		if (IS_ERR(skt->stat[i].desc))
+			return PTR_ERR(skt->stat[i].desc);
+	}
+	return 0;
+}
+
+static int sa11x0_cf_configure_socket(struct soc_pcmcia_socket *skt,
+	const socket_state_t *state)
+{
+	return soc_pcmcia_regulator_set(skt, &skt->vcc, state->Vcc);
+}
+
+static struct pcmcia_low_level sa11x0_cf_ops = {
+	.owner = THIS_MODULE,
+	.hw_init = sa11x0_cf_hw_init,
+	.socket_state = soc_common_cf_socket_state,
+	.configure_socket = sa11x0_cf_configure_socket,
+};
+
 int __init pcmcia_collie_init(struct device *dev);
 
-static int (*sa11x0_pcmcia_hw_init[])(struct device *dev) = {
-#ifdef CONFIG_SA1100_ASSABET
-	pcmcia_assabet_init,
-#endif
-#ifdef CONFIG_SA1100_CERF
-	pcmcia_cerf_init,
-#endif
+static int (*sa11x0_pcmcia_legacy_hw_init[])(struct device *dev) = {
 #if defined(CONFIG_SA1100_H3100) || defined(CONFIG_SA1100_H3600)
 	pcmcia_h3600_init,
 #endif
-#ifdef CONFIG_SA1100_NANOENGINE
-	pcmcia_nanoengine_init,
-#endif
-#ifdef CONFIG_SA1100_SHANNON
-	pcmcia_shannon_init,
-#endif
 #ifdef CONFIG_SA1100_SIMPAD
 	pcmcia_simpad_init,
 #endif
@@ -67,15 +109,15 @@ static int (*sa11x0_pcmcia_hw_init[])(struct device *dev) = {
 #endif
 };
 
-static int sa11x0_drv_pcmcia_probe(struct platform_device *dev)
+static int sa11x0_drv_pcmcia_legacy_probe(struct platform_device *dev)
 {
 	int i, ret = -ENODEV;
 
 	/*
 	 * Initialise any "on-board" PCMCIA sockets.
 	 */
-	for (i = 0; i < ARRAY_SIZE(sa11x0_pcmcia_hw_init); i++) {
-		ret = sa11x0_pcmcia_hw_init[i](&dev->dev);
+	for (i = 0; i < ARRAY_SIZE(sa11x0_pcmcia_legacy_hw_init); i++) {
+		ret = sa11x0_pcmcia_legacy_hw_init[i](&dev->dev);
 		if (ret == 0)
 			break;
 	}
@@ -83,7 +125,7 @@ static int sa11x0_drv_pcmcia_probe(struct platform_device *dev)
 	return ret;
 }
 
-static int sa11x0_drv_pcmcia_remove(struct platform_device *dev)
+static int sa11x0_drv_pcmcia_legacy_remove(struct platform_device *dev)
 {
 	struct skt_dev_info *sinfo = platform_get_drvdata(dev);
 	int i;
@@ -96,6 +138,45 @@ static int sa11x0_drv_pcmcia_remove(struct platform_device *dev)
 	return 0;
 }
 
+static int sa11x0_drv_pcmcia_probe(struct platform_device *pdev)
+{
+	struct soc_pcmcia_socket *skt;
+	struct device *dev = &pdev->dev;
+
+	if (pdev->id == -1)
+		return sa11x0_drv_pcmcia_legacy_probe(pdev);
+
+	skt = devm_kzalloc(dev, sizeof(*skt), GFP_KERNEL);
+	if (!skt)
+		return -ENOMEM;
+
+	platform_set_drvdata(pdev, skt);
+
+	skt->nr = pdev->id;
+	skt->clk = devm_clk_get(dev, NULL);
+	if (IS_ERR(skt->clk))
+		return PTR_ERR(skt->clk);
+
+	sa11xx_drv_pcmcia_ops(&sa11x0_cf_ops);
+	soc_pcmcia_init_one(skt, &sa11x0_cf_ops, dev);
+
+	return sa11xx_drv_pcmcia_add_one(skt);
+}
+
+static int sa11x0_drv_pcmcia_remove(struct platform_device *dev)
+{
+	struct soc_pcmcia_socket *skt;
+
+	if (dev->id == -1)
+		return sa11x0_drv_pcmcia_legacy_remove(dev);
+
+	skt = platform_get_drvdata(dev);
+
+	soc_pcmcia_remove_one(skt);
+
+	return 0;
+}
+
 static struct platform_driver sa11x0_pcmcia_driver = {
 	.driver = {
 		.name		= "sa11x0-pcmcia",
diff --git a/drivers/pcmcia/sa1100_generic.h b/drivers/pcmcia/sa1100_generic.h
index a5f1f1dd63cbb..7b7cdcd20187a 100644
--- a/drivers/pcmcia/sa1100_generic.h
+++ b/drivers/pcmcia/sa1100_generic.h
@@ -6,18 +6,14 @@
  * Declaration for all machine specific init/exit functions.
  */
 extern int pcmcia_adsbitsy_init(struct device *);
-extern int pcmcia_assabet_init(struct device *);
 extern int pcmcia_badge4_init(struct device *);
-extern int pcmcia_cerf_init(struct device *);
 extern int pcmcia_flexanet_init(struct device *);
 extern int pcmcia_freebird_init(struct device *);
 extern int pcmcia_gcplus_init(struct device *);
 extern int pcmcia_graphicsmaster_init(struct device *);
 extern int pcmcia_h3600_init(struct device *);
-extern int pcmcia_nanoengine_init(struct device *);
 extern int pcmcia_pangolin_init(struct device *);
 extern int pcmcia_pfs168_init(struct device *);
-extern int pcmcia_shannon_init(struct device *);
 extern int pcmcia_simpad_init(struct device *);
 extern int pcmcia_stork_init(struct device *);
 extern int pcmcia_system3_init(struct device *);
diff --git a/drivers/pcmcia/sa1100_h3600.c b/drivers/pcmcia/sa1100_h3600.c
index aebf9a66fddea..a91222bc3824c 100644
--- a/drivers/pcmcia/sa1100_h3600.c
+++ b/drivers/pcmcia/sa1100_h3600.c
@@ -24,13 +24,15 @@ static int h3600_pcmcia_hw_init(struct soc_pcmcia_socket *skt)
 {
 	int err;
 
+	skt->stat[SOC_STAT_CD].name = skt->nr ? "pcmcia1-detect" : "pcmcia0-detect";
+	skt->stat[SOC_STAT_RDY].name = skt->nr ? "pcmcia1-ready" : "pcmcia0-ready";
+
+	err = soc_pcmcia_request_gpiods(skt);
+	if (err)
+		return err;
+
 	switch (skt->nr) {
 	case 0:
-		skt->stat[SOC_STAT_CD].gpio = H3XXX_GPIO_PCMCIA_CD0;
-		skt->stat[SOC_STAT_CD].name = "PCMCIA CD0";
-		skt->stat[SOC_STAT_RDY].gpio = H3XXX_GPIO_PCMCIA_IRQ0;
-		skt->stat[SOC_STAT_RDY].name = "PCMCIA IRQ0";
-
 		err = gpio_request(H3XXX_EGPIO_OPT_NVRAM_ON, "OPT NVRAM ON");
 		if (err)
 			goto err01;
@@ -57,10 +59,6 @@ static int h3600_pcmcia_hw_init(struct soc_pcmcia_socket *skt)
 			goto err06;
 		break;
 	case 1:
-		skt->stat[SOC_STAT_CD].gpio = H3XXX_GPIO_PCMCIA_CD1;
-		skt->stat[SOC_STAT_CD].name = "PCMCIA CD1";
-		skt->stat[SOC_STAT_RDY].gpio = H3XXX_GPIO_PCMCIA_IRQ1;
-		skt->stat[SOC_STAT_RDY].name = "PCMCIA IRQ1";
 		break;
 	}
 	return 0;
diff --git a/drivers/pcmcia/sa1100_nanoengine.c b/drivers/pcmcia/sa1100_nanoengine.c
deleted file mode 100644
index 35c30ff41e817..0000000000000
--- a/drivers/pcmcia/sa1100_nanoengine.c
+++ /dev/null
@@ -1,133 +0,0 @@
-/*
- * drivers/pcmcia/sa1100_nanoengine.c
- *
- * PCMCIA implementation routines for BSI nanoEngine.
- *
- * In order to have a fully functional pcmcia subsystem in a BSE nanoEngine
- * board you should carefully read this:
- * http://cambuca.ldhs.cetuc.puc-rio.br/nanoengine/
- *
- * Copyright (C) 2010 Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
- *
- * Based on original work for kernel 2.4 by
- * Miguel Freitas <miguel@cpti.cetuc.puc-rio.br>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- */
-#include <linux/device.h>
-#include <linux/errno.h>
-#include <linux/gpio.h>
-#include <linux/interrupt.h>
-#include <linux/irq.h>
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/signal.h>
-
-#include <asm/mach-types.h>
-#include <asm/irq.h>
-
-#include <mach/hardware.h>
-#include <mach/nanoengine.h>
-
-#include "sa1100_generic.h"
-
-struct nanoengine_pins {
-	unsigned output_pins;
-	unsigned clear_outputs;
-	int gpio_rst;
-	int gpio_cd;
-	int gpio_rdy;
-};
-
-static struct nanoengine_pins nano_skts[] = {
-	{
-		.gpio_rst		= GPIO_PC_RESET0,
-		.gpio_cd		= GPIO_PC_CD0,
-		.gpio_rdy		= GPIO_PC_READY0,
-	}, {
-		.gpio_rst		= GPIO_PC_RESET1,
-		.gpio_cd		= GPIO_PC_CD1,
-		.gpio_rdy		= GPIO_PC_READY1,
-	}
-};
-
-unsigned num_nano_pcmcia_sockets = ARRAY_SIZE(nano_skts);
-
-static int nanoengine_pcmcia_hw_init(struct soc_pcmcia_socket *skt)
-{
-	unsigned i = skt->nr;
-	int ret;
-
-	if (i >= num_nano_pcmcia_sockets)
-		return -ENXIO;
-
-	ret = gpio_request_one(nano_skts[i].gpio_rst, GPIOF_OUT_INIT_LOW,
-		i ? "PC RST1" : "PC RST0");
-	if (ret)
-		return ret;
-
-	skt->stat[SOC_STAT_CD].gpio = nano_skts[i].gpio_cd;
-	skt->stat[SOC_STAT_CD].name = i ? "PC CD1" : "PC CD0";
-	skt->stat[SOC_STAT_RDY].gpio = nano_skts[i].gpio_rdy;
-	skt->stat[SOC_STAT_RDY].name = i ? "PC RDY1" : "PC RDY0";
-
-	return 0;
-}
-
-static void nanoengine_pcmcia_hw_shutdown(struct soc_pcmcia_socket *skt)
-{
-	gpio_free(nano_skts[skt->nr].gpio_rst);
-}
-
-static int nanoengine_pcmcia_configure_socket(
-	struct soc_pcmcia_socket *skt, const socket_state_t *state)
-{
-	unsigned i = skt->nr;
-
-	if (i >= num_nano_pcmcia_sockets)
-		return -ENXIO;
-
-	gpio_set_value(nano_skts[skt->nr].gpio_rst, !!(state->flags & SS_RESET));
-
-	return 0;
-}
-
-static void nanoengine_pcmcia_socket_state(
-	struct soc_pcmcia_socket *skt, struct pcmcia_state *state)
-{
-	unsigned i = skt->nr;
-
-	if (i >= num_nano_pcmcia_sockets)
-		return;
-
-	state->bvd1 = 1;
-	state->bvd2 = 1;
-	state->vs_3v = 1; /* Can only apply 3.3V */
-	state->vs_Xv = 0;
-}
-
-static struct pcmcia_low_level nanoengine_pcmcia_ops = {
-	.owner			= THIS_MODULE,
-
-	.hw_init		= nanoengine_pcmcia_hw_init,
-	.hw_shutdown		= nanoengine_pcmcia_hw_shutdown,
-
-	.configure_socket	= nanoengine_pcmcia_configure_socket,
-	.socket_state		= nanoengine_pcmcia_socket_state,
-};
-
-int pcmcia_nanoengine_init(struct device *dev)
-{
-	int ret = -ENODEV;
-
-	if (machine_is_nanoengine())
-		ret = sa11xx_drv_pcmcia_probe(
-			dev, &nanoengine_pcmcia_ops, 0, 2);
-
-	return ret;
-}
-
diff --git a/drivers/pcmcia/sa1100_shannon.c b/drivers/pcmcia/sa1100_shannon.c
deleted file mode 100644
index 0e52a575986e0..0000000000000
--- a/drivers/pcmcia/sa1100_shannon.c
+++ /dev/null
@@ -1,104 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * drivers/pcmcia/sa1100_shannon.c
- *
- * PCMCIA implementation routines for Shannon
- *
- */
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/device.h>
-#include <linux/init.h>
-#include <linux/io.h>
-
-#include <mach/hardware.h>
-#include <asm/mach-types.h>
-#include <mach/shannon.h>
-#include <asm/irq.h>
-#include "sa1100_generic.h"
-
-static int shannon_pcmcia_hw_init(struct soc_pcmcia_socket *skt)
-{
-	/* All those are inputs */
-	GAFR &= ~(GPIO_GPIO(SHANNON_GPIO_EJECT_0) |
-		  GPIO_GPIO(SHANNON_GPIO_EJECT_1) |
-		  GPIO_GPIO(SHANNON_GPIO_RDY_0) |
-		  GPIO_GPIO(SHANNON_GPIO_RDY_1));
-
-	if (skt->nr == 0) {
-		skt->stat[SOC_STAT_CD].gpio = SHANNON_GPIO_EJECT_0;
-		skt->stat[SOC_STAT_CD].name = "PCMCIA_CD_0";
-		skt->stat[SOC_STAT_RDY].gpio = SHANNON_GPIO_RDY_0;
-		skt->stat[SOC_STAT_RDY].name = "PCMCIA_RDY_0";
-	} else {
-		skt->stat[SOC_STAT_CD].gpio = SHANNON_GPIO_EJECT_1;
-		skt->stat[SOC_STAT_CD].name = "PCMCIA_CD_1";
-		skt->stat[SOC_STAT_RDY].gpio = SHANNON_GPIO_RDY_1;
-		skt->stat[SOC_STAT_RDY].name = "PCMCIA_RDY_1";
-	}
-
-	return 0;
-}
-
-static void
-shannon_pcmcia_socket_state(struct soc_pcmcia_socket *skt,
-			    struct pcmcia_state *state)
-{
-	switch (skt->nr) {
-	case 0:
-		state->bvd1   = 1; 
-		state->bvd2   = 1; 
-		state->vs_3v  = 1; /* FIXME Can only apply 3.3V on Shannon. */
-		state->vs_Xv  = 0;
-		break;
-
-	case 1:
-		state->bvd1   = 1; 
-		state->bvd2   = 1; 
-		state->vs_3v  = 1; /* FIXME Can only apply 3.3V on Shannon. */
-		state->vs_Xv  = 0;
-		break;
-	}
-}
-
-static int
-shannon_pcmcia_configure_socket(struct soc_pcmcia_socket *skt,
-				const socket_state_t *state)
-{
-	switch (state->Vcc) {
-	case 0:	/* power off */
-		printk(KERN_WARNING "%s(): CS asked for 0V, still applying 3.3V..\n", __func__);
-		break;
-	case 50:
-		printk(KERN_WARNING "%s(): CS asked for 5V, applying 3.3V..\n", __func__);
-	case 33:
-		break;
-	default:
-		printk(KERN_ERR "%s(): unrecognized Vcc %u\n",
-		       __func__, state->Vcc);
-		return -1;
-	}
-
-	printk(KERN_WARNING "%s(): Warning, Can't perform reset\n", __func__);
-	
-	/* Silently ignore Vpp, output enable, speaker enable. */
-
-	return 0;
-}
-
-static struct pcmcia_low_level shannon_pcmcia_ops = {
-	.owner			= THIS_MODULE,
-	.hw_init		= shannon_pcmcia_hw_init,
-	.socket_state		= shannon_pcmcia_socket_state,
-	.configure_socket	= shannon_pcmcia_configure_socket,
-};
-
-int pcmcia_shannon_init(struct device *dev)
-{
-	int ret = -ENODEV;
-
-	if (machine_is_shannon())
-		ret = sa11xx_drv_pcmcia_probe(dev, &shannon_pcmcia_ops, 0, 2);
-
-	return ret;
-}
diff --git a/drivers/pcmcia/sa1100_simpad.c b/drivers/pcmcia/sa1100_simpad.c
index 7ce65bb23a8ee..e235ee14eaa6e 100644
--- a/drivers/pcmcia/sa1100_simpad.c
+++ b/drivers/pcmcia/sa1100_simpad.c
@@ -12,7 +12,6 @@
 
 #include <mach/hardware.h>
 #include <asm/mach-types.h>
-#include <asm/irq.h>
 #include <mach/simpad.h>
 #include "sa1100_generic.h"
  
@@ -21,12 +20,10 @@ static int simpad_pcmcia_hw_init(struct soc_pcmcia_socket *skt)
 
 	simpad_clear_cs3_bit(VCC_3V_EN|VCC_5V_EN|EN0|EN1);
 
-	skt->stat[SOC_STAT_CD].gpio = GPIO_CF_CD;
-	skt->stat[SOC_STAT_CD].name = "CF_CD";
-	skt->stat[SOC_STAT_RDY].gpio = GPIO_CF_IRQ;
-	skt->stat[SOC_STAT_RDY].name = "CF_RDY";
+	skt->stat[SOC_STAT_CD].name = "cf-detect";
+	skt->stat[SOC_STAT_RDY].name = "cf-ready";
 
-	return 0;
+	return soc_pcmcia_request_gpiods(skt);
 }
 
 static void simpad_pcmcia_hw_shutdown(struct soc_pcmcia_socket *skt)
@@ -42,9 +39,6 @@ simpad_pcmcia_socket_state(struct soc_pcmcia_socket *skt,
 {
 	long cs3reg = simpad_get_cs3_ro();
 
-	/* the detect signal is inverted - fix that up here */
-	state->detect = !state->detect;
-
 	state->bvd1 = 1; /* Might be cs3reg & PCMCIA_BVD1 */
 	state->bvd2 = 1; /* Might be cs3reg & PCMCIA_BVD2 */