Merge branch 'i2c/for-4.14' of git://git.kernel.org/pub/scm/linux/ker…

…nel/git/wsa/linux

Pull i2c updates from Wolfram Sang:

 - new drivers for Spreadtrum I2C, Intel Cherry Trail Whiskey Cove SMBUS

 - quite some driver updates

 - cleanups for the i2c-mux subsystem

 - some subsystem-wide constification

 - further cleanup of include/linux/i2c

* 'i2c/for-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (50 commits)
  i2c: sprd: Fix undefined reference errors
  i2c: nomadik: constify amba_id
  i2c: versatile: Make i2c_algo_bit_data const
  i2c: busses: make i2c_adapter_quirks const
  i2c: busses: make i2c_adapter const
  i2c: busses: make i2c_algorithm const
  i2c: Add Spreadtrum I2C controller driver
  dt-bindings: i2c: Add Spreadtrum I2C controller documentation
  i2c-cht-wc: make cht_wc_i2c_adap_driver static
  MAINTAINERS: Add entry for drivers/i2c/busses/i2c-cht-wc.c
  i2c: aspeed: Retain delay/setup/hold values when configuring bus frequency
  dt-bindings: i2c: eeprom: Document vendor to be used and deprecated ones
  i2c: i801: Restore the presence state of P2SB PCI device after reading BAR
  MAINTAINERS: drop entry for Blackfin I2C and Sonic's email
  blackfin: merge the two TWI header files
  i2c: davinci: Preserve return value of devm_clk_get
  i2c: mediatek: Add i2c compatible for MediaTek MT7622
  dt-bindings: i2c: Add MediaTek MT7622 i2c binding
  dt-bindings: i2c: modify information formats
  i2c: mux: i2c-arb-gpio-challenge: allow compiling w/o OF support
  ...

Documentation/devicetree/bindings/eeprom/eeprom.txt

@@ -16,8 +16,12 @@ Required properties:
 
 	"renesas,r1ex24002"
 
+	The following manufacturers values have been deprecated:
+	"at", "at24"
+
 	 If there is no specific driver for <manufacturer>, a generic
-	 driver based on <type> is selected. Possible types are:
+	 device with <type> and manufacturer "atmel" should be used.
+	 Possible types are:
 	 "24c00", "24c01", "24c02", "24c04", "24c08", "24c16", "24c32", "24c64",
 	 "24c128", "24c256", "24c512", "24c1024", "spd"
 

Documentation/devicetree/bindings/i2c/i2c-mtk.txt

@@ -1,14 +1,15 @@
-* Mediatek's I2C controller
+* MediaTek's I2C controller
 
-The Mediatek's I2C controller is used to interface with I2C devices.
+The MediaTek's I2C controller is used to interface with I2C devices.
 
 Required properties:
   - compatible: value should be either of the following.
-      "mediatek,mt2701-i2c", "mediatek,mt6577-i2c": for Mediatek mt2701
-      "mediatek,mt6577-i2c": for i2c compatible with mt6577.
-      "mediatek,mt6589-i2c": for i2c compatible with mt6589.
-      "mediatek,mt7623-i2c", "mediatek,mt6577-i2c": for i2c compatible with mt7623.
-      "mediatek,mt8173-i2c": for i2c compatible with mt8173.
+      "mediatek,mt2701-i2c", "mediatek,mt6577-i2c": for MediaTek MT2701
+      "mediatek,mt6577-i2c": for MediaTek MT6577
+      "mediatek,mt6589-i2c": for MediaTek MT6589
+      "mediatek,mt7622-i2c": for MediaTek MT7622
+      "mediatek,mt7623-i2c", "mediatek,mt6577-i2c": for MediaTek MT7623
+      "mediatek,mt8173-i2c": for MediaTek MT8173
   - reg: physical base address of the controller and dma base, length of memory
     mapped region.
   - interrupts: interrupt number to the cpu.

Documentation/devicetree/bindings/i2c/i2c-rcar.txt

@@ -2,6 +2,8 @@ I2C for R-Car platforms
 
 Required properties:
 - compatible:
+	"renesas,i2c-r8a7743" if the device is a part of a R8A7743 SoC.
+	"renesas,i2c-r8a7745" if the device is a part of a R8A7745 SoC.
 	"renesas,i2c-r8a7778" if the device is a part of a R8A7778 SoC.
 	"renesas,i2c-r8a7779" if the device is a part of a R8A7779 SoC.
 	"renesas,i2c-r8a7790" if the device is a part of a R8A7790 SoC.
@@ -12,7 +14,8 @@ Required properties:
 	"renesas,i2c-r8a7795" if the device is a part of a R8A7795 SoC.
 	"renesas,i2c-r8a7796" if the device is a part of a R8A7796 SoC.
 	"renesas,rcar-gen1-i2c" for a generic R-Car Gen1 compatible device.
-	"renesas,rcar-gen2-i2c" for a generic R-Car Gen2 compatible device.
+	"renesas,rcar-gen2-i2c" for a generic R-Car Gen2 or RZ/G1 compatible
+				device.
 	"renesas,rcar-gen3-i2c" for a generic R-Car Gen3 compatible device.
 	"renesas,i2c-rcar" (deprecated)
 

Documentation/devicetree/bindings/i2c/i2c-rk3x.txt

@@ -7,6 +7,7 @@ Required properties :
 
  - reg : Offset and length of the register set for the device
  - compatible: should be one of the following:
+   - "rockchip,rv1108-i2c": for rv1108
    - "rockchip,rk3066-i2c": for rk3066
    - "rockchip,rk3188-i2c": for rk3188
    - "rockchip,rk3228-i2c": for rk3228

Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt

@@ -4,6 +4,8 @@ Required properties:
 - compatible      :
 			- "renesas,iic-r8a73a4" (R-Mobile APE6)
 			- "renesas,iic-r8a7740" (R-Mobile A1)
+			- "renesas,iic-r8a7743" (RZ/G1M)
+			- "renesas,iic-r8a7745" (RZ/G1E)
 			- "renesas,iic-r8a7790" (R-Car H2)
 			- "renesas,iic-r8a7791" (R-Car M2-W)
 			- "renesas,iic-r8a7792" (R-Car V2H)
@@ -12,7 +14,8 @@ Required properties:
 			- "renesas,iic-r8a7795" (R-Car H3)
 			- "renesas,iic-r8a7796" (R-Car M3-W)
 			- "renesas,iic-sh73a0" (SH-Mobile AG5)
-			- "renesas,rcar-gen2-iic" (generic R-Car Gen2 compatible device)
+			- "renesas,rcar-gen2-iic" (generic R-Car Gen2 or RZ/G1
+							compatible device)
 			- "renesas,rcar-gen3-iic" (generic R-Car Gen3 compatible device)
 			- "renesas,rmobile-iic" (generic device)
 

Documentation/devicetree/bindings/i2c/i2c-sprd.txt

@@ -0,0 +1,31 @@
+I2C for Spreadtrum platforms
+
+Required properties:
+- compatible: Should be "sprd,sc9860-i2c".
+- reg: Specify the physical base address of the controller and length
+  of memory mapped region.
+- interrupts: Should contain I2C interrupt.
+- clock-names: Should contain following entries:
+  "i2c" for I2C clock,
+  "source" for I2C source (parent) clock,
+  "enable" for I2C module enable clock.
+- clocks: Should contain a clock specifier for each entry in clock-names.
+- clock-frequency: Constains desired I2C bus clock frequency in Hz.
+- #address-cells: Should be 1 to describe address cells for I2C device address.
+- #size-cells: Should be 0 means no size cell for I2C device address.
+
+Optional properties:
+- Child nodes conforming to I2C bus binding
+
+Examples:
+i2c0: i2c@70500000 {
+	compatible = "sprd,sc9860-i2c";
+	reg = <0 0x70500000 0 0x1000>;
+	interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+	clock-names = "i2c", "source", "enable";
+	clocks = <&clk_i2c3>, <&ext_26m>, <&clk_ap_apb_gates 11>;
+	clock-frequency = <400000>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+};
+

Documentation/i2c/i2c-topology

@@ -42,6 +42,10 @@ i2c-arb-gpio-challenge    Parent-locked
 i2c-mux-gpio              Normally parent-locked, mux-locked iff
                           all involved gpio pins are controlled by the
                           same i2c root adapter that they mux.
+i2c-mux-gpmux             Normally parent-locked, mux-locked iff
+                          specified in device-tree.
+i2c-mux-ltc4306           Mux-locked
+i2c-mux-mlxcpld           Parent-locked
 i2c-mux-pca9541           Parent-locked
 i2c-mux-pca954x           Parent-locked
 i2c-mux-pinctrl           Normally parent-locked, mux-locked iff
@@ -50,9 +54,11 @@ i2c-mux-pinctrl           Normally parent-locked, mux-locked iff
 i2c-mux-reg               Parent-locked
 
 In drivers/iio/
+gyro/mpu3050              Mux-locked
 imu/inv_mpu6050/          Mux-locked
 
 In drivers/media/
+dvb-frontends/lgdt3306a   Mux-locked
 dvb-frontends/m88ds3103   Parent-locked
 dvb-frontends/rtl2830     Parent-locked
 dvb-frontends/rtl2832     Mux-locked

MAINTAINERS

@@ -2575,13 +2575,6 @@ W:	http://blackfin.uclinux.org
 S:	Supported
 F:	drivers/net/ethernet/adi/
 
-BLACKFIN I2C TWI DRIVER
-M:	Sonic Zhang <sonic.zhang@analog.com>
-L:	adi-buildroot-devel@lists.sourceforge.net (moderated for non-subscribers)
-W:	http://blackfin.uclinux.org/
-S:	Supported
-F:	drivers/i2c/busses/i2c-bfin-twi.c
-
 BLACKFIN MEDIA DRIVER
 M:	Scott Jiang <scott.jiang.linux@gmail.com>
 L:	adi-buildroot-devel@lists.sourceforge.net (moderated for non-subscribers)
@@ -2598,14 +2591,12 @@ S:	Supported
 F:	drivers/rtc/rtc-bfin.c
 
 BLACKFIN SDH DRIVER
-M:	Sonic Zhang <sonic.zhang@analog.com>
 L:	adi-buildroot-devel@lists.sourceforge.net (moderated for non-subscribers)
 W:	http://blackfin.uclinux.org
 S:	Supported
 F:	drivers/mmc/host/bfin_sdh.c
 
 BLACKFIN SERIAL DRIVER
-M:	Sonic Zhang <sonic.zhang@analog.com>
 L:	adi-buildroot-devel@lists.sourceforge.net (moderated for non-subscribers)
 W:	http://blackfin.uclinux.org
 S:	Supported
@@ -6441,6 +6432,12 @@ F:	drivers/i2c/busses/i2c-sis96x.c
 F:	drivers/i2c/busses/i2c-via.c
 F:	drivers/i2c/busses/i2c-viapro.c
 
+I2C/SMBUS INTEL CHT WHISKEY COVE PMIC DRIVER
+M:	Hans de Goede <hdegoede@redhat.com>
+L:	linux-i2c@vger.kernel.org
+S:	Maintained
+F:	drivers/i2c/busses/i2c-cht-wc.c
+
 I2C/SMBUS ISMT DRIVER
 M:	Seth Heasley <seth.heasley@intel.com>
 M:	Neil Horman <nhorman@tuxdriver.com>

arch/blackfin/include/asm/bfin_twi.h

@@ -1,7 +1,7 @@
 /*
  * bfin_twi.h - interface to Blackfin TWIs
  *
- * Copyright 2005-2010 Analog Devices Inc.
+ * Copyright 2005-2014 Analog Devices Inc.
  *
  * Licensed under the GPL-2 or later.
  */
@@ -10,6 +10,138 @@
 #define __ASM_BFIN_TWI_H__
 
 #include <asm/blackfin.h>
+#include <linux/types.h>
+#include <linux/i2c.h>
+
+/*
+ * ADI twi registers layout
+ */
+struct bfin_twi_regs {
+	u16 clkdiv;
+	u16 dummy1;
+	u16 control;
+	u16 dummy2;
+	u16 slave_ctl;
+	u16 dummy3;
+	u16 slave_stat;
+	u16 dummy4;
+	u16 slave_addr;
+	u16 dummy5;
+	u16 master_ctl;
+	u16 dummy6;
+	u16 master_stat;
+	u16 dummy7;
+	u16 master_addr;
+	u16 dummy8;
+	u16 int_stat;
+	u16 dummy9;
+	u16 int_mask;
+	u16 dummy10;
+	u16 fifo_ctl;
+	u16 dummy11;
+	u16 fifo_stat;
+	u16 dummy12;
+	u32 __pad[20];
+	u16 xmt_data8;
+	u16 dummy13;
+	u16 xmt_data16;
+	u16 dummy14;
+	u16 rcv_data8;
+	u16 dummy15;
+	u16 rcv_data16;
+	u16 dummy16;
+};
+
+struct bfin_twi_iface {
+	int			irq;
+	spinlock_t		lock;
+	char			read_write;
+	u8			command;
+	u8			*transPtr;
+	int			readNum;
+	int			writeNum;
+	int			cur_mode;
+	int			manual_stop;
+	int			result;
+	struct i2c_adapter	adap;
+	struct completion	complete;
+	struct i2c_msg		*pmsg;
+	int			msg_num;
+	int			cur_msg;
+	u16			saved_clkdiv;
+	u16			saved_control;
+	struct bfin_twi_regs __iomem *regs_base;
+};
+
+/*  ********************  TWO-WIRE INTERFACE (TWI) MASKS  ********************/
+/* TWI_CLKDIV Macros (Use: *pTWI_CLKDIV = CLKLOW(x)|CLKHI(y);  ) */
+#define	CLKLOW(x)	((x) & 0xFF)	/* Periods Clock Is Held Low */
+#define CLKHI(y)	(((y)&0xFF)<<0x8) /* Periods Before New Clock Low */
+
+/* TWI_PRESCALE Masks */
+#define	PRESCALE	0x007F	/* SCLKs Per Internal Time Reference (10MHz) */
+#define	TWI_ENA		0x0080	/* TWI Enable */
+#define	SCCB		0x0200	/* SCCB Compatibility Enable */
+
+/* TWI_SLAVE_CTL Masks */
+#define	SEN		0x0001	/* Slave Enable */
+#define	SADD_LEN	0x0002	/* Slave Address Length */
+#define	STDVAL		0x0004	/* Slave Transmit Data Valid */
+#define	NAK		0x0008	/* NAK Generated At Conclusion Of Transfer */
+#define	GEN		0x0010	/* General Call Address Matching Enabled */
+
+/* TWI_SLAVE_STAT Masks	*/
+#define	SDIR		0x0001	/* Slave Transfer Direction (RX/TX*) */
+#define GCALL		0x0002	/* General Call Indicator */
+
+/* TWI_MASTER_CTL Masks	*/
+#define	MEN		0x0001	/* Master Mode Enable          */
+#define	MADD_LEN	0x0002	/* Master Address Length       */
+#define	MDIR		0x0004	/* Master Transmit Direction (RX/TX*) */
+#define	FAST		0x0008	/* Use Fast Mode Timing Specs  */
+#define	STOP		0x0010	/* Issue Stop Condition        */
+#define	RSTART		0x0020	/* Repeat Start or Stop* At End Of Transfer */
+#define	DCNT		0x3FC0	/* Data Bytes To Transfer      */
+#define	SDAOVR		0x4000	/* Serial Data Override        */
+#define	SCLOVR		0x8000	/* Serial Clock Override       */
+
+/* TWI_MASTER_STAT Masks */
+#define	MPROG		0x0001	/* Master Transfer In Progress */
+#define	LOSTARB		0x0002	/* Lost Arbitration Indicator (Xfer Aborted) */
+#define	ANAK		0x0004	/* Address Not Acknowledged    */
+#define	DNAK		0x0008	/* Data Not Acknowledged       */
+#define	BUFRDERR	0x0010	/* Buffer Read Error           */
+#define	BUFWRERR	0x0020	/* Buffer Write Error          */
+#define	SDASEN		0x0040	/* Serial Data Sense           */
+#define	SCLSEN		0x0080	/* Serial Clock Sense          */
+#define	BUSBUSY		0x0100	/* Bus Busy Indicator          */
+
+/* TWI_INT_SRC and TWI_INT_ENABLE Masks	*/
+#define	SINIT		0x0001	/* Slave Transfer Initiated    */
+#define	SCOMP		0x0002	/* Slave Transfer Complete     */
+#define	SERR		0x0004	/* Slave Transfer Error        */
+#define	SOVF		0x0008	/* Slave Overflow              */
+#define	MCOMP		0x0010	/* Master Transfer Complete    */
+#define	MERR		0x0020	/* Master Transfer Error       */
+#define	XMTSERV		0x0040	/* Transmit FIFO Service       */
+#define	RCVSERV		0x0080	/* Receive FIFO Service        */
+
+/* TWI_FIFO_CTRL Masks */
+#define	XMTFLUSH	0x0001	/* Transmit Buffer Flush                 */
+#define	RCVFLUSH	0x0002	/* Receive Buffer Flush                  */
+#define	XMTINTLEN	0x0004	/* Transmit Buffer Interrupt Length      */
+#define	RCVINTLEN	0x0008	/* Receive Buffer Interrupt Length       */
+
+/* TWI_FIFO_STAT Masks */
+#define	XMTSTAT		0x0003	/* Transmit FIFO Status                  */
+#define	XMT_EMPTY	0x0000	/* Transmit FIFO Empty                   */
+#define	XMT_HALF	0x0001	/* Transmit FIFO Has 1 Byte To Write     */
+#define	XMT_FULL	0x0003	/* Transmit FIFO Full (2 Bytes To Write) */
+
+#define	RCVSTAT		0x000C	/* Receive FIFO Status                   */
+#define	RCV_EMPTY	0x0000	/* Receive FIFO Empty                    */
+#define	RCV_HALF	0x0004	/* Receive FIFO Has 1 Byte To Read       */
+#define	RCV_FULL	0x000C	/* Receive FIFO Full (2 Bytes To Read)   */
 
 #define DEFINE_TWI_REG(reg_name, reg) \
 static inline u16 read_##reg_name(struct bfin_twi_iface *iface) \

arch/blackfin/kernel/debug-mmrs.c

@@ -10,7 +10,6 @@
 #include <linux/fs.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
-#include <linux/i2c/bfin_twi.h>
 #include <linux/gpio.h>
 
 #include <asm/blackfin.h>

arch/x86/platform/intel-mid/device_libs/platform_tc35876x.c

@@ -11,7 +11,7 @@
  */
 
 #include <linux/gpio.h>
-#include <linux/i2c/tc35876x.h>
+#include <linux/platform_data/tc35876x.h>
 #include <asm/intel-mid.h>
 
 /*tc35876x DSI_LVDS bridge chip and panel platform data*/

drivers/gpu/drm/gma500/tc35876x-dsi-lvds.c

@@ -26,7 +26,7 @@
 #include "mdfld_output.h"
 #include "mdfld_dsi_pkg_sender.h"
 #include "tc35876x-dsi-lvds.h"
-#include <linux/i2c/tc35876x.h>
+#include <linux/platform_data/tc35876x.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <asm/intel_scu_ipc.h>

drivers/i2c/busses/Kconfig

@@ -189,6 +189,14 @@ config I2C_PIIX4
 	  This driver can also be built as a module.  If so, the module
 	  will be called i2c-piix4.
 
+config I2C_CHT_WC
+	tristate "Intel Cherry Trail Whiskey Cove PMIC smbus controller"
+	depends on INTEL_SOC_PMIC_CHTWC
+	help
+	  If you say yes to this option, support will be included for the
+	  SMBus controller found in the Intel Cherry Trail Whiskey Cove PMIC
+	  found on some Intel Cherry Trail systems.
+
 config I2C_NFORCE2
 	tristate "Nvidia nForce2, nForce3 and nForce4"
 	depends on PCI
@@ -900,6 +908,13 @@ config I2C_SIRF
 	  This driver can also be built as a module.  If so, the module
 	  will be called i2c-sirf.
 
+config I2C_SPRD
+	bool "Spreadtrum I2C interface"
+	depends on I2C=y && ARCH_SPRD
+	help
+	  If you say yes to this option, support will be included for the
+	  Spreadtrum I2C interface.
+
 config I2C_ST
 	tristate "STMicroelectronics SSC I2C support"
 	depends on ARCH_STI

drivers/i2c/busses/Makefile

@@ -12,6 +12,7 @@ obj-$(CONFIG_I2C_ALI15X3)	+= i2c-ali15x3.o
 obj-$(CONFIG_I2C_AMD756)	+= i2c-amd756.o
 obj-$(CONFIG_I2C_AMD756_S4882)	+= i2c-amd756-s4882.o
 obj-$(CONFIG_I2C_AMD8111)	+= i2c-amd8111.o
+obj-$(CONFIG_I2C_CHT_WC)	+= i2c-cht-wc.o
 obj-$(CONFIG_I2C_I801)		+= i2c-i801.o
 obj-$(CONFIG_I2C_ISCH)		+= i2c-isch.o
 obj-$(CONFIG_I2C_ISMT)		+= i2c-ismt.o
@@ -89,6 +90,7 @@ obj-$(CONFIG_I2C_SH7760)	+= i2c-sh7760.o
 obj-$(CONFIG_I2C_SH_MOBILE)	+= i2c-sh_mobile.o
 obj-$(CONFIG_I2C_SIMTEC)	+= i2c-simtec.o
 obj-$(CONFIG_I2C_SIRF)		+= i2c-sirf.o
+obj-$(CONFIG_I2C_SPRD)		+= i2c-sprd.o
 obj-$(CONFIG_I2C_ST)		+= i2c-st.o
 obj-$(CONFIG_I2C_STM32F4)	+= i2c-stm32f4.o
 obj-$(CONFIG_I2C_STU300)	+= i2c-stu300.o