diff --git a/Documentation/devicetree/bindings/net/sff,sfp.txt b/Documentation/devicetree/bindings/net/sff,sfp.txt deleted file mode 100644 index 832139919f20a..0000000000000 --- a/Documentation/devicetree/bindings/net/sff,sfp.txt +++ /dev/null @@ -1,85 +0,0 @@ -Small Form Factor (SFF) Committee Small Form-factor Pluggable (SFP) -Transceiver - -Required properties: - -- compatible : must be one of - "sff,sfp" for SFP modules - "sff,sff" for soldered down SFF modules - -- i2c-bus : phandle of an I2C bus controller for the SFP two wire serial - interface - -Optional Properties: - -- mod-def0-gpios : GPIO phandle and a specifier of the MOD-DEF0 (AKA Mod_ABS) - module presence input gpio signal, active (module absent) high. Must - not be present for SFF modules - -- los-gpios : GPIO phandle and a specifier of the Receiver Loss of Signal - Indication input gpio signal, active (signal lost) high - -- tx-fault-gpios : GPIO phandle and a specifier of the Module Transmitter - Fault input gpio signal, active (fault condition) high - -- tx-disable-gpios : GPIO phandle and a specifier of the Transmitter Disable - output gpio signal, active (Tx disable) high - -- rate-select0-gpios : GPIO phandle and a specifier of the Rx Signaling Rate - Select (AKA RS0) output gpio signal, low: low Rx rate, high: high Rx rate - Must not be present for SFF modules - -- rate-select1-gpios : GPIO phandle and a specifier of the Tx Signaling Rate - Select (AKA RS1) output gpio signal (SFP+ only), low: low Tx rate, high: - high Tx rate. Must not be present for SFF modules - -- maximum-power-milliwatt : Maximum module power consumption - Specifies the maximum power consumption allowable by a module in the - slot, in milli-Watts. Presently, modules can be up to 1W, 1.5W or 2W. - -Example #1: Direct serdes to SFP connection - -sfp_eth3: sfp-eth3 { - compatible = "sff,sfp"; - i2c-bus = <&sfp_1g_i2c>; - los-gpios = <&cpm_gpio2 22 GPIO_ACTIVE_HIGH>; - mod-def0-gpios = <&cpm_gpio2 21 GPIO_ACTIVE_LOW>; - maximum-power-milliwatt = <1000>; - pinctrl-names = "default"; - pinctrl-0 = <&cpm_sfp_1g_pins &cps_sfp_1g_pins>; - tx-disable-gpios = <&cps_gpio1 24 GPIO_ACTIVE_HIGH>; - tx-fault-gpios = <&cpm_gpio2 19 GPIO_ACTIVE_HIGH>; -}; - -&cps_emac3 { - phy-names = "comphy"; - phys = <&cps_comphy5 0>; - sfp = <&sfp_eth3>; -}; - -Example #2: Serdes to PHY to SFP connection - -sfp_eth0: sfp-eth0 { - compatible = "sff,sfp"; - i2c-bus = <&sfpp0_i2c>; - los-gpios = <&cps_gpio1 28 GPIO_ACTIVE_HIGH>; - mod-def0-gpios = <&cps_gpio1 27 GPIO_ACTIVE_LOW>; - pinctrl-names = "default"; - pinctrl-0 = <&cps_sfpp0_pins>; - tx-disable-gpios = <&cps_gpio1 29 GPIO_ACTIVE_HIGH>; - tx-fault-gpios = <&cps_gpio1 26 GPIO_ACTIVE_HIGH>; -}; - -p0_phy: ethernet-phy@0 { - compatible = "ethernet-phy-ieee802.3-c45"; - pinctrl-names = "default"; - pinctrl-0 = <&cpm_phy0_pins &cps_phy0_pins>; - reg = <0>; - interrupt = <&cpm_gpio2 18 IRQ_TYPE_EDGE_FALLING>; - sfp = <&sfp_eth0>; -}; - -&cpm_eth0 { - phy = <&p0_phy>; - phy-mode = "10gbase-kr"; -}; diff --git a/Documentation/devicetree/bindings/net/sff,sfp.yaml b/Documentation/devicetree/bindings/net/sff,sfp.yaml new file mode 100644 index 0000000000000..06c66ab81c01e --- /dev/null +++ b/Documentation/devicetree/bindings/net/sff,sfp.yaml @@ -0,0 +1,142 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/net/sff,sfp.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Small Form Factor (SFF) Committee Small Form-factor Pluggable (SFP) + Transceiver + +maintainers: + - Russell King + +properties: + compatible: + enum: + - sff,sfp # for SFP modules + - sff,sff # for soldered down SFF modules + + i2c-bus: + $ref: /schemas/types.yaml#/definitions/phandle + description: + phandle of an I2C bus controller for the SFP two wire serial + + maximum-power-milliwatt: + maxItems: 1 + description: + Maximum module power consumption Specifies the maximum power consumption + allowable by a module in the slot, in milli-Watts. Presently, modules can + be up to 1W, 1.5W or 2W. + + "mod-def0-gpios": + maxItems: 1 + description: + GPIO phandle and a specifier of the MOD-DEF0 (AKA Mod_ABS) module + presence input gpio signal, active (module absent) high. Must not be + present for SFF modules + + "los-gpios": + maxItems: 1 + description: + GPIO phandle and a specifier of the Receiver Loss of Signal Indication + input gpio signal, active (signal lost) high + + "tx-fault-gpios": + maxItems: 1 + description: + GPIO phandle and a specifier of the Module Transmitter Fault input gpio + signal, active (fault condition) high + + "tx-disable-gpios": + maxItems: 1 + description: + GPIO phandle and a specifier of the Transmitter Disable output gpio + signal, active (Tx disable) high + + "rate-select0-gpios": + maxItems: 1 + description: + GPIO phandle and a specifier of the Rx Signaling Rate Select (AKA RS0) + output gpio signal, low - low Rx rate, high - high Rx rate Must not be + present for SFF modules + + "rate-select1-gpios": + maxItems: 1 + description: + GPIO phandle and a specifier of the Tx Signaling Rate Select (AKA RS1) + output gpio signal (SFP+ only), low - low Tx rate, high - high Tx rate. Must + not be present for SFF modules + +allOf: + - if: + properties: + compatible: + contains: + const: sff,sff + then: + properties: + mod-def0-gpios: false + rate-select0-gpios: false + rate-select1-gpios: false + +required: + - compatible + - i2c-bus + +additionalProperties: false + +examples: + - | # Direct serdes to SFP connection + #include + + sfp1: sfp { + compatible = "sff,sfp"; + i2c-bus = <&sfp_1g_i2c>; + los-gpios = <&cpm_gpio2 22 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&cpm_gpio2 21 GPIO_ACTIVE_LOW>; + maximum-power-milliwatt = <1000>; + pinctrl-names = "default"; + pinctrl-0 = <&cpm_sfp_1g_pins &cps_sfp_1g_pins>; + tx-disable-gpios = <&cps_gpio1 24 GPIO_ACTIVE_HIGH>; + tx-fault-gpios = <&cpm_gpio2 19 GPIO_ACTIVE_HIGH>; + }; + + ethernet { + phy-names = "comphy"; + phys = <&cps_comphy5 0>; + sfp = <&sfp1>; + }; + + - | # Serdes to PHY to SFP connection + #include + #include + + sfp2: sfp { + compatible = "sff,sfp"; + i2c-bus = <&sfp_i2c>; + los-gpios = <&cps_gpio1 28 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&cps_gpio1 27 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&cps_sfpp0_pins>; + tx-disable-gpios = <&cps_gpio1 29 GPIO_ACTIVE_HIGH>; + tx-fault-gpios = <&cps_gpio1 26 GPIO_ACTIVE_HIGH>; + }; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c45"; + pinctrl-names = "default"; + pinctrl-0 = <&cpm_phy0_pins &cps_phy0_pins>; + reg = <0>; + interrupt = <&cpm_gpio2 18 IRQ_TYPE_EDGE_FALLING>; + sfp = <&sfp2>; + }; + }; + + ethernet { + phy = <&phy>; + phy-mode = "10gbase-kr"; + }; diff --git a/MAINTAINERS b/MAINTAINERS index 14b07494e86a5..5fc2af7eb9bd0 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -18189,6 +18189,7 @@ SFF/SFP/SFP+ MODULE SUPPORT M: Russell King L: netdev@vger.kernel.org S: Maintained +F: Documentation/devicetree/bindings/net/sff,sfp.yaml F: drivers/net/phy/phylink.c F: drivers/net/phy/sfp* F: include/linux/mdio/mdio-i2c.h diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-clearfog-itx.dtsi b/arch/arm64/boot/dts/freescale/fsl-lx2160a-clearfog-itx.dtsi index 41702e7386e37..a7dcbecc1f41b 100644 --- a/arch/arm64/boot/dts/freescale/fsl-lx2160a-clearfog-itx.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-clearfog-itx.dtsi @@ -34,28 +34,28 @@ sfp0: sfp-0 { compatible = "sff,sfp"; i2c-bus = <&sfp0_i2c>; - mod-def0-gpio = <&gpio2 0 GPIO_ACTIVE_LOW>; + mod-def0-gpios = <&gpio2 0 GPIO_ACTIVE_LOW>; maximum-power-milliwatt = <2000>; }; sfp1: sfp-1 { compatible = "sff,sfp"; i2c-bus = <&sfp1_i2c>; - mod-def0-gpio = <&gpio2 9 GPIO_ACTIVE_LOW>; + mod-def0-gpios = <&gpio2 9 GPIO_ACTIVE_LOW>; maximum-power-milliwatt = <2000>; }; sfp2: sfp-2 { compatible = "sff,sfp"; i2c-bus = <&sfp2_i2c>; - mod-def0-gpio = <&gpio2 10 GPIO_ACTIVE_LOW>; + mod-def0-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>; maximum-power-milliwatt = <2000>; }; sfp3: sfp-3 { compatible = "sff,sfp"; i2c-bus = <&sfp3_i2c>; - mod-def0-gpio = <&gpio2 11 GPIO_ACTIVE_LOW>; + mod-def0-gpios = <&gpio2 11 GPIO_ACTIVE_LOW>; maximum-power-milliwatt = <2000>; }; }; diff --git a/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts b/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts index caf9c8529fcaf..cbf75ddd68571 100644 --- a/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts +++ b/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts @@ -100,11 +100,11 @@ sfp: sfp { compatible = "sff,sfp"; i2c-bus = <&i2c0>; - los-gpio = <&moxtet_sfp 0 GPIO_ACTIVE_HIGH>; - tx-fault-gpio = <&moxtet_sfp 1 GPIO_ACTIVE_HIGH>; - mod-def0-gpio = <&moxtet_sfp 2 GPIO_ACTIVE_LOW>; - tx-disable-gpio = <&moxtet_sfp 4 GPIO_ACTIVE_HIGH>; - rate-select0-gpio = <&moxtet_sfp 5 GPIO_ACTIVE_HIGH>; + los-gpios = <&moxtet_sfp 0 GPIO_ACTIVE_HIGH>; + tx-fault-gpios = <&moxtet_sfp 1 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&moxtet_sfp 2 GPIO_ACTIVE_LOW>; + tx-disable-gpios = <&moxtet_sfp 4 GPIO_ACTIVE_HIGH>; + rate-select0-gpios = <&moxtet_sfp 5 GPIO_ACTIVE_HIGH>; maximum-power-milliwatt = <3000>; /* enabled by U-Boot if SFP module is present */ diff --git a/arch/arm64/boot/dts/marvell/armada-3720-uDPU.dts b/arch/arm64/boot/dts/marvell/armada-3720-uDPU.dts index a35317d24d6c9..b20c8e7d923b1 100644 --- a/arch/arm64/boot/dts/marvell/armada-3720-uDPU.dts +++ b/arch/arm64/boot/dts/marvell/armada-3720-uDPU.dts @@ -65,20 +65,20 @@ sfp_eth0: sfp-eth0 { compatible = "sff,sfp"; i2c-bus = <&i2c0>; - los-gpio = <&gpiosb 2 GPIO_ACTIVE_HIGH>; - mod-def0-gpio = <&gpiosb 3 GPIO_ACTIVE_LOW>; - tx-disable-gpio = <&gpiosb 4 GPIO_ACTIVE_HIGH>; - tx-fault-gpio = <&gpiosb 5 GPIO_ACTIVE_HIGH>; + los-gpios = <&gpiosb 2 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&gpiosb 3 GPIO_ACTIVE_LOW>; + tx-disable-gpios = <&gpiosb 4 GPIO_ACTIVE_HIGH>; + tx-fault-gpios = <&gpiosb 5 GPIO_ACTIVE_HIGH>; maximum-power-milliwatt = <3000>; }; sfp_eth1: sfp-eth1 { compatible = "sff,sfp"; i2c-bus = <&i2c1>; - los-gpio = <&gpiosb 7 GPIO_ACTIVE_HIGH>; - mod-def0-gpio = <&gpiosb 8 GPIO_ACTIVE_LOW>; - tx-disable-gpio = <&gpiosb 9 GPIO_ACTIVE_HIGH>; - tx-fault-gpio = <&gpiosb 10 GPIO_ACTIVE_HIGH>; + los-gpios = <&gpiosb 7 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&gpiosb 8 GPIO_ACTIVE_LOW>; + tx-disable-gpios = <&gpiosb 9 GPIO_ACTIVE_HIGH>; + tx-fault-gpios = <&gpiosb 10 GPIO_ACTIVE_HIGH>; maximum-power-milliwatt = <3000>; }; }; diff --git a/arch/arm64/boot/dts/marvell/armada-7040-mochabin.dts b/arch/arm64/boot/dts/marvell/armada-7040-mochabin.dts index 39a8e5e99d799..5f6ed735e31aa 100644 --- a/arch/arm64/boot/dts/marvell/armada-7040-mochabin.dts +++ b/arch/arm64/boot/dts/marvell/armada-7040-mochabin.dts @@ -34,20 +34,20 @@ sfp_eth0: sfp-eth0 { compatible = "sff,sfp"; i2c-bus = <&cp0_i2c1>; - los-gpio = <&sfp_gpio 3 GPIO_ACTIVE_HIGH>; - mod-def0-gpio = <&sfp_gpio 2 GPIO_ACTIVE_LOW>; - tx-disable-gpio = <&sfp_gpio 1 GPIO_ACTIVE_HIGH>; - tx-fault-gpio = <&sfp_gpio 0 GPIO_ACTIVE_HIGH>; + los-gpios = <&sfp_gpio 3 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sfp_gpio 2 GPIO_ACTIVE_LOW>; + tx-disable-gpios = <&sfp_gpio 1 GPIO_ACTIVE_HIGH>; + tx-fault-gpios = <&sfp_gpio 0 GPIO_ACTIVE_HIGH>; }; /* SFP 1G */ sfp_eth2: sfp-eth2 { compatible = "sff,sfp"; i2c-bus = <&cp0_i2c0>; - los-gpio = <&sfp_gpio 7 GPIO_ACTIVE_HIGH>; - mod-def0-gpio = <&sfp_gpio 6 GPIO_ACTIVE_LOW>; - tx-disable-gpio = <&sfp_gpio 5 GPIO_ACTIVE_HIGH>; - tx-fault-gpio = <&sfp_gpio 4 GPIO_ACTIVE_HIGH>; + los-gpios = <&sfp_gpio 7 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sfp_gpio 6 GPIO_ACTIVE_LOW>; + tx-disable-gpios = <&sfp_gpio 5 GPIO_ACTIVE_HIGH>; + tx-fault-gpios = <&sfp_gpio 4 GPIO_ACTIVE_HIGH>; }; }; diff --git a/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts b/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts index 871f84b4a6ed0..079c2745070a4 100644 --- a/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts +++ b/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts @@ -64,8 +64,8 @@ sfp_cp0_eth0: sfp-cp0-eth0 { compatible = "sff,sfp"; i2c-bus = <&cp0_i2c1>; - mod-def0-gpio = <&cp0_gpio2 17 GPIO_ACTIVE_LOW>; - tx-disable-gpio = <&cp1_gpio1 29 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&cp0_gpio2 17 GPIO_ACTIVE_LOW>; + tx-disable-gpios = <&cp1_gpio1 29 GPIO_ACTIVE_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&cp0_sfp_present_pins &cp1_sfp_tx_disable_pins>; maximum-power-milliwatt = <2000>; diff --git a/arch/arm64/boot/dts/marvell/armada-8040-mcbin.dtsi b/arch/arm64/boot/dts/marvell/armada-8040-mcbin.dtsi index 779cf167c33e2..33c179838e241 100644 --- a/arch/arm64/boot/dts/marvell/armada-8040-mcbin.dtsi +++ b/arch/arm64/boot/dts/marvell/armada-8040-mcbin.dtsi @@ -65,10 +65,10 @@ /* CON15,16 - CPM lane 4 */ compatible = "sff,sfp"; i2c-bus = <&sfpp0_i2c>; - los-gpio = <&cp1_gpio1 28 GPIO_ACTIVE_HIGH>; - mod-def0-gpio = <&cp1_gpio1 27 GPIO_ACTIVE_LOW>; - tx-disable-gpio = <&cp1_gpio1 29 GPIO_ACTIVE_HIGH>; - tx-fault-gpio = <&cp1_gpio1 26 GPIO_ACTIVE_HIGH>; + los-gpios = <&cp1_gpio1 28 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&cp1_gpio1 27 GPIO_ACTIVE_LOW>; + tx-disable-gpios = <&cp1_gpio1 29 GPIO_ACTIVE_HIGH>; + tx-fault-gpios = <&cp1_gpio1 26 GPIO_ACTIVE_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&cp1_sfpp0_pins>; maximum-power-milliwatt = <2000>; @@ -78,10 +78,10 @@ /* CON17,18 - CPS lane 4 */ compatible = "sff,sfp"; i2c-bus = <&sfpp1_i2c>; - los-gpio = <&cp1_gpio1 8 GPIO_ACTIVE_HIGH>; - mod-def0-gpio = <&cp1_gpio1 11 GPIO_ACTIVE_LOW>; - tx-disable-gpio = <&cp1_gpio1 10 GPIO_ACTIVE_HIGH>; - tx-fault-gpio = <&cp0_gpio2 30 GPIO_ACTIVE_HIGH>; + los-gpios = <&cp1_gpio1 8 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&cp1_gpio1 11 GPIO_ACTIVE_LOW>; + tx-disable-gpios = <&cp1_gpio1 10 GPIO_ACTIVE_HIGH>; + tx-fault-gpios = <&cp0_gpio2 30 GPIO_ACTIVE_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&cp1_sfpp1_pins &cp0_sfpp1_pins>; maximum-power-milliwatt = <2000>; @@ -91,10 +91,10 @@ /* CON13,14 - CPS lane 5 */ compatible = "sff,sfp"; i2c-bus = <&sfp_1g_i2c>; - los-gpio = <&cp0_gpio2 22 GPIO_ACTIVE_HIGH>; - mod-def0-gpio = <&cp0_gpio2 21 GPIO_ACTIVE_LOW>; - tx-disable-gpio = <&cp1_gpio1 24 GPIO_ACTIVE_HIGH>; - tx-fault-gpio = <&cp0_gpio2 19 GPIO_ACTIVE_HIGH>; + los-gpios = <&cp0_gpio2 22 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&cp0_gpio2 21 GPIO_ACTIVE_LOW>; + tx-disable-gpios = <&cp1_gpio1 24 GPIO_ACTIVE_HIGH>; + tx-fault-gpios = <&cp0_gpio2 19 GPIO_ACTIVE_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&cp0_sfp_1g_pins &cp1_sfp_1g_pins>; maximum-power-milliwatt = <2000>; diff --git a/arch/arm64/boot/dts/marvell/armada-8040-puzzle-m801.dts b/arch/arm64/boot/dts/marvell/armada-8040-puzzle-m801.dts index 74bed79e4f5ed..72e9b0f671a90 100644 --- a/arch/arm64/boot/dts/marvell/armada-8040-puzzle-m801.dts +++ b/arch/arm64/boot/dts/marvell/armada-8040-puzzle-m801.dts @@ -67,20 +67,20 @@ sfp_cp0_eth0: sfp-cp0-eth0 { compatible = "sff,sfp"; i2c-bus = <&sfpplus0_i2c>; - los-gpio = <&sfpplus_gpio 11 GPIO_ACTIVE_HIGH>; - mod-def0-gpio = <&sfpplus_gpio 10 GPIO_ACTIVE_LOW>; - tx-disable-gpio = <&sfpplus_gpio 9 GPIO_ACTIVE_HIGH>; - tx-fault-gpio = <&sfpplus_gpio 8 GPIO_ACTIVE_HIGH>; + los-gpios = <&sfpplus_gpio 11 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sfpplus_gpio 10 GPIO_ACTIVE_LOW>; + tx-disable-gpios = <&sfpplus_gpio 9 GPIO_ACTIVE_HIGH>; + tx-fault-gpios = <&sfpplus_gpio 8 GPIO_ACTIVE_HIGH>; maximum-power-milliwatt = <3000>; }; sfp_cp1_eth0: sfp-cp1-eth0 { compatible = "sff,sfp"; i2c-bus = <&sfpplus1_i2c>; - los-gpio = <&sfpplus_gpio 3 GPIO_ACTIVE_HIGH>; - mod-def0-gpio = <&sfpplus_gpio 2 GPIO_ACTIVE_LOW>; - tx-disable-gpio = <&sfpplus_gpio 1 GPIO_ACTIVE_HIGH>; - tx-fault-gpio = <&sfpplus_gpio 0 GPIO_ACTIVE_HIGH>; + los-gpios = <&sfpplus_gpio 3 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&sfpplus_gpio 2 GPIO_ACTIVE_LOW>; + tx-disable-gpios = <&sfpplus_gpio 1 GPIO_ACTIVE_HIGH>; + tx-fault-gpios = <&sfpplus_gpio 0 GPIO_ACTIVE_HIGH>; maximum-power-milliwatt = <3000>; }; diff --git a/arch/arm64/boot/dts/marvell/cn9130-crb.dtsi b/arch/arm64/boot/dts/marvell/cn9130-crb.dtsi index 1acd746284dc7..8e4ec243fb8fc 100644 --- a/arch/arm64/boot/dts/marvell/cn9130-crb.dtsi +++ b/arch/arm64/boot/dts/marvell/cn9130-crb.dtsi @@ -78,9 +78,9 @@ compatible = "sff,sfp"; i2c-bus = <&cp0_i2c1>; mod-def0-gpios = <&expander0 3 GPIO_ACTIVE_LOW>; - los-gpio = <&expander0 15 GPIO_ACTIVE_HIGH>; - tx-disable-gpio = <&expander0 2 GPIO_ACTIVE_HIGH>; - tx-fault-gpio = <&cp0_gpio1 24 GPIO_ACTIVE_HIGH>; + los-gpios = <&expander0 15 GPIO_ACTIVE_HIGH>; + tx-disable-gpios = <&expander0 2 GPIO_ACTIVE_HIGH>; + tx-fault-gpios = <&cp0_gpio1 24 GPIO_ACTIVE_HIGH>; maximum-power-milliwatt = <3000>; status = "okay"; }; diff --git a/arch/arm64/boot/dts/marvell/cn9130-db.dtsi b/arch/arm64/boot/dts/marvell/cn9130-db.dtsi index 7e20987253a38..85d7ce13e70a2 100644 --- a/arch/arm64/boot/dts/marvell/cn9130-db.dtsi +++ b/arch/arm64/boot/dts/marvell/cn9130-db.dtsi @@ -90,10 +90,10 @@ cp0_sfp_eth0: sfp-eth@0 { compatible = "sff,sfp"; i2c-bus = <&cp0_sfpp0_i2c>; - los-gpio = <&cp0_module_expander1 11 GPIO_ACTIVE_HIGH>; - mod-def0-gpio = <&cp0_module_expander1 10 GPIO_ACTIVE_LOW>; - tx-disable-gpio = <&cp0_module_expander1 9 GPIO_ACTIVE_HIGH>; - tx-fault-gpio = <&cp0_module_expander1 8 GPIO_ACTIVE_HIGH>; + los-gpios = <&cp0_module_expander1 11 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&cp0_module_expander1 10 GPIO_ACTIVE_LOW>; + tx-disable-gpios = <&cp0_module_expander1 9 GPIO_ACTIVE_HIGH>; + tx-fault-gpios = <&cp0_module_expander1 8 GPIO_ACTIVE_HIGH>; /* * SFP cages are unconnected on early PCBs because of an the I2C * lanes not being connected. Prevent the port for being diff --git a/arch/arm64/boot/dts/marvell/cn9131-db.dtsi b/arch/arm64/boot/dts/marvell/cn9131-db.dtsi index b7fc241a228cc..ff8422fae31b5 100644 --- a/arch/arm64/boot/dts/marvell/cn9131-db.dtsi +++ b/arch/arm64/boot/dts/marvell/cn9131-db.dtsi @@ -37,10 +37,10 @@ cp1_sfp_eth1: sfp-eth1 { compatible = "sff,sfp"; i2c-bus = <&cp1_i2c0>; - los-gpio = <&cp1_gpio1 11 GPIO_ACTIVE_HIGH>; - mod-def0-gpio = <&cp1_gpio1 10 GPIO_ACTIVE_LOW>; - tx-disable-gpio = <&cp1_gpio1 9 GPIO_ACTIVE_HIGH>; - tx-fault-gpio = <&cp1_gpio1 8 GPIO_ACTIVE_HIGH>; + los-gpios = <&cp1_gpio1 11 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&cp1_gpio1 10 GPIO_ACTIVE_LOW>; + tx-disable-gpios = <&cp1_gpio1 9 GPIO_ACTIVE_HIGH>; + tx-fault-gpios = <&cp1_gpio1 8 GPIO_ACTIVE_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&cp1_sfp_pins>; /* diff --git a/arch/arm64/boot/dts/marvell/cn9132-db.dtsi b/arch/arm64/boot/dts/marvell/cn9132-db.dtsi index 3f1795fb4fe72..512a4fa2861e7 100644 --- a/arch/arm64/boot/dts/marvell/cn9132-db.dtsi +++ b/arch/arm64/boot/dts/marvell/cn9132-db.dtsi @@ -57,10 +57,10 @@ cp2_sfp_eth0: sfp-eth0 { compatible = "sff,sfp"; i2c-bus = <&cp2_sfpp0_i2c>; - los-gpio = <&cp2_module_expander1 11 GPIO_ACTIVE_HIGH>; - mod-def0-gpio = <&cp2_module_expander1 10 GPIO_ACTIVE_LOW>; - tx-disable-gpio = <&cp2_module_expander1 9 GPIO_ACTIVE_HIGH>; - tx-fault-gpio = <&cp2_module_expander1 8 GPIO_ACTIVE_HIGH>; + los-gpios = <&cp2_module_expander1 11 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&cp2_module_expander1 10 GPIO_ACTIVE_LOW>; + tx-disable-gpios = <&cp2_module_expander1 9 GPIO_ACTIVE_HIGH>; + tx-fault-gpios = <&cp2_module_expander1 8 GPIO_ACTIVE_HIGH>; /* * SFP cages are unconnected on early PCBs because of an the I2C * lanes not being connected. Prevent the port for being