Merge tag 'iio-fixes-for-4.8a' of git://git.kernel.org/pub/scm/linux/…

…kernel/git/jic23/iio into work-linus

Jonathan writes:

First round of IIO fixes for the 4.8 cycle.

This is somewhat of a bumper set due to my unavailabilty earlier in the
month.  The only slightly unusual ones are the dts updates for the
rockchip adc reset.  The fix in the driver only makes sense with these
and the rockchip maintainer is happy with them going through IIO to
reach mainline.

Core stuff

* Fix an issue with a blocking op when !TASK_RUNNING. This been there
  a while and snuck in with seemingly minor additions to some core
  code paths.
* Tools
  - generic_buffer failed to initialize the channel array pointer thus
    in the case of no channels blows up trying to free a random memory
    address.
* sw-trigger:
  - Fix config group initialization when configfs is built as a module.

Drivers

* ad5933
  - Fix an incorrect overwrite of an error value.
* ad799x
  - A missed assignment of the update_scan_mode callback means buffered mode
    doesn't work on the ad7991, ad7995 or ad7999.
* ads1015
  - wrong pointer returned from i2c_get_clientdata (missmatch of assumptions)
* am2315
  - Timestamps are reported, but never actually acquired from anywhere
    (so always 0)
  - missing buffer selects in Kconfig
* am335x adc
  - Protect fifo1 from concurrent access.
  - Increase timeout waiting for ADC to be long enough in all cases.
* as3935
  - Timestamps are reported, but never actually acquired from anywhere
    (so always 0)
* at91
  - Fix reading of channel 3.
* atlas-ph-sensor
  - Typo means that the scale of electrical conductivity readings is way off.
* bma220
  - Timestamps are reported, but never actually acquired from anywhere
    (so always 0)
  - Missing buffer selects in Kconfig
* bmp280
  - pass the write pointer to PTR_ERR (i.e. the one that was just checked
    with IS_ERR).
  - suspend /resume crash due to wrong assumption about what dev_get_drvdata
    would return.
* hdc100x
  - It superficially appeared that smbus_read_byte commands would allow
  reading of the outputs in two goes.  In reality it doesn't work, but
  instead returns the same for the upper and lower bytes (nice catch from
  Alison!)
* kxsd9
  - Fix raw read return value to ensure it actually reports the value rather
  than a blank string.
* max44000
  - Missing buffer selects in Kconfig
* rockchip_saradc
  - Add use of reset controller to enforce a clean state of the ADC.
    Some bootloaders can leave it in an 'intersting' state and effectively
    frozen without this. A couple of associated dts updates.
* stk8ba50
  - Missing buffer selects in Kconfig
* stx104
  - Fix a possible race due to use of devm_iio_device_register when there
    was other stuff in the remove function.

Documentation/devicetree/bindings/iio/adc/rockchip-saradc.txt

@@ -16,13 +16,20 @@ Required properties:
 - vref-supply: The regulator supply ADC reference voltage.
 - #io-channel-cells: Should be 1, see ../iio-bindings.txt
 
+Optional properties:
+- resets: Must contain an entry for each entry in reset-names if need support
+	  this option. See ../reset/reset.txt for details.
+- reset-names: Must include the name "saradc-apb".
+
 Example:
 	saradc: saradc@2006c000 {
 		compatible = "rockchip,saradc";
 		reg = <0x2006c000 0x100>;
 		interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&cru SCLK_SARADC>, <&cru PCLK_SARADC>;
 		clock-names = "saradc", "apb_pclk";
+		resets = <&cru SRST_SARADC>;
+		reset-names = "saradc-apb";
 		#io-channel-cells = <1>;
 		vref-supply = <&vcc18>;
 	};

arch/arm/boot/dts/rk3066a.dtsi

@@ -197,6 +197,8 @@
 		clock-names = "saradc", "apb_pclk";
 		interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
 		#io-channel-cells = <1>;
+		resets = <&cru SRST_SARADC>;
+		reset-names = "saradc-apb";
 		status = "disabled";
 	};
 

arch/arm/boot/dts/rk3288.dtsi

@@ -279,6 +279,8 @@
 		#io-channel-cells = <1>;
 		clocks = <&cru SCLK_SARADC>, <&cru PCLK_SARADC>;
 		clock-names = "saradc", "apb_pclk";
+		resets = <&cru SRST_SARADC>;
+		reset-names = "saradc-apb";
 		status = "disabled";
 	};
 

arch/arm/boot/dts/rk3xxx.dtsi

@@ -399,6 +399,8 @@
 		#io-channel-cells = <1>;
 		clocks = <&cru SCLK_SARADC>, <&cru PCLK_SARADC>;
 		clock-names = "saradc", "apb_pclk";
+		resets = <&cru SRST_SARADC>;
+		reset-names = "saradc-apb";
 		status = "disabled";
 	};
 

arch/arm64/boot/dts/rockchip/rk3368.dtsi

@@ -270,6 +270,8 @@
 		#io-channel-cells = <1>;
 		clocks = <&cru SCLK_SARADC>, <&cru PCLK_SARADC>;
 		clock-names = "saradc", "apb_pclk";
+		resets = <&cru SRST_SARADC>;
+		reset-names = "saradc-apb";
 		status = "disabled";
 	};
 

drivers/iio/accel/Kconfig

@@ -20,6 +20,8 @@ config BMA180
 config BMA220
     tristate "Bosch BMA220 3-Axis Accelerometer Driver"
 	depends on SPI
+	select IIO_BUFFER
+	select IIO_TRIGGERED_BUFFER
     help
       Say yes here to add support for the Bosch BMA220 triaxial
       acceleration sensor.
@@ -234,7 +236,8 @@ config STK8312
 config STK8BA50
 	tristate "Sensortek STK8BA50 3-Axis Accelerometer Driver"
 	depends on I2C
-	depends on IIO_TRIGGER
+	select IIO_BUFFER
+	select IIO_TRIGGERED_BUFFER
 	help
 	  Say yes here to get support for the Sensortek STK8BA50 3-axis
 	  accelerometer.

drivers/iio/accel/bma220_spi.c

@@ -253,7 +253,7 @@ static int bma220_probe(struct spi_device *spi)
 	if (ret < 0)
 		return ret;
 
-	ret = iio_triggered_buffer_setup(indio_dev, NULL,
+	ret = iio_triggered_buffer_setup(indio_dev, iio_pollfunc_store_time,
 					 bma220_trigger_handler, NULL);
 	if (ret < 0) {
 		dev_err(&spi->dev, "iio triggered buffer setup failed\n");

drivers/iio/accel/kxsd9.c

@@ -160,6 +160,7 @@ static int kxsd9_read_raw(struct iio_dev *indio_dev,
 		if (ret < 0)
 			goto error_ret;
 		*val = ret;
+		ret = IIO_VAL_INT;
 		break;
 	case IIO_CHAN_INFO_SCALE:
 		ret = spi_w8r8(st->us, KXSD9_READ(KXSD9_REG_CTRL_C));

drivers/iio/adc/Kconfig

@@ -389,6 +389,7 @@ config QCOM_SPMI_VADC
 config ROCKCHIP_SARADC
 	tristate "Rockchip SARADC driver"
 	depends on ARCH_ROCKCHIP || (ARM && COMPILE_TEST)
+	depends on RESET_CONTROLLER
 	help
 	  Say yes here to build support for the SARADC found in SoCs from
 	  Rockchip.

drivers/iio/adc/ad799x.c

@@ -527,6 +527,7 @@ static struct attribute_group ad799x_event_attrs_group = {
 static const struct iio_info ad7991_info = {
 	.read_raw = &ad799x_read_raw,
 	.driver_module = THIS_MODULE,
+	.update_scan_mode = ad799x_update_scan_mode,
 };
 
 static const struct iio_info ad7993_4_7_8_noirq_info = {

drivers/iio/adc/at91_adc.c

@@ -381,8 +381,8 @@ static irqreturn_t at91_adc_rl_interrupt(int irq, void *private)
 		st->ts_bufferedmeasure = false;
 		input_report_key(st->ts_input, BTN_TOUCH, 0);
 		input_sync(st->ts_input);
-	} else if (status & AT91_ADC_EOC(3)) {
-		/* Conversion finished */
+	} else if (status & AT91_ADC_EOC(3) && st->ts_input) {
+		/* Conversion finished and we've a touchscreen */
 		if (st->ts_bufferedmeasure) {
 			/*
 			 * Last measurement is always discarded, since it can

drivers/iio/adc/rockchip_saradc.c

@@ -21,6 +21,8 @@
 #include <linux/of_device.h>
 #include <linux/clk.h>
 #include <linux/completion.h>
+#include <linux/delay.h>
+#include <linux/reset.h>
 #include <linux/regulator/consumer.h>
 #include <linux/iio/iio.h>
 
@@ -53,6 +55,7 @@ struct rockchip_saradc {
 	struct clk		*clk;
 	struct completion	completion;
 	struct regulator	*vref;
+	struct reset_control	*reset;
 	const struct rockchip_saradc_data *data;
 	u16			last_val;
 };
@@ -190,6 +193,16 @@ static const struct of_device_id rockchip_saradc_match[] = {
 };
 MODULE_DEVICE_TABLE(of, rockchip_saradc_match);
 
+/**
+ * Reset SARADC Controller.
+ */
+static void rockchip_saradc_reset_controller(struct reset_control *reset)
+{
+	reset_control_assert(reset);
+	usleep_range(10, 20);
+	reset_control_deassert(reset);
+}
+
 static int rockchip_saradc_probe(struct platform_device *pdev)
 {
 	struct rockchip_saradc *info = NULL;
@@ -218,6 +231,20 @@ static int rockchip_saradc_probe(struct platform_device *pdev)
 	if (IS_ERR(info->regs))
 		return PTR_ERR(info->regs);
 
+	/*
+	 * The reset should be an optional property, as it should work
+	 * with old devicetrees as well
+	 */
+	info->reset = devm_reset_control_get(&pdev->dev, "saradc-apb");
+	if (IS_ERR(info->reset)) {
+		ret = PTR_ERR(info->reset);
+		if (ret != -ENOENT)
+			return ret;
+
+		dev_dbg(&pdev->dev, "no reset control found\n");
+		info->reset = NULL;
+	}
+
 	init_completion(&info->completion);
 
 	irq = platform_get_irq(pdev, 0);
@@ -252,6 +279,9 @@ static int rockchip_saradc_probe(struct platform_device *pdev)
 		return PTR_ERR(info->vref);
 	}
 
+	if (info->reset)
+		rockchip_saradc_reset_controller(info->reset);
+
 	/*
 	 * Use a default value for the converter clock.
 	 * This may become user-configurable in the future.

drivers/iio/adc/ti-ads1015.c

@@ -489,7 +489,8 @@ static struct iio_info ads1115_info = {
 #ifdef CONFIG_OF
 static int ads1015_get_channels_config_of(struct i2c_client *client)
 {
-	struct ads1015_data *data = i2c_get_clientdata(client);
+	struct iio_dev *indio_dev = i2c_get_clientdata(client);
+	struct ads1015_data *data = iio_priv(indio_dev);
 	struct device_node *node;
 
 	if (!client->dev.of_node ||

drivers/iio/adc/ti_am335x_adc.c

@@ -32,6 +32,7 @@
 
 struct tiadc_device {
 	struct ti_tscadc_dev *mfd_tscadc;
+	struct mutex fifo1_lock; /* to protect fifo access */
 	int channels;
 	u8 channel_line[8];
 	u8 channel_step[8];
@@ -359,6 +360,7 @@ static int tiadc_read_raw(struct iio_dev *indio_dev,
 		int *val, int *val2, long mask)
 {
 	struct tiadc_device *adc_dev = iio_priv(indio_dev);
+	int ret = IIO_VAL_INT;
 	int i, map_val;
 	unsigned int fifo1count, read, stepid;
 	bool found = false;
@@ -372,13 +374,14 @@ static int tiadc_read_raw(struct iio_dev *indio_dev,
 	if (!step_en)
 		return -EINVAL;
 
+	mutex_lock(&adc_dev->fifo1_lock);
 	fifo1count = tiadc_readl(adc_dev, REG_FIFO1CNT);
 	while (fifo1count--)
 		tiadc_readl(adc_dev, REG_FIFO1);
 
 	am335x_tsc_se_set_once(adc_dev->mfd_tscadc, step_en);
 
-	timeout = jiffies + usecs_to_jiffies
+	timeout = jiffies + msecs_to_jiffies
 				(IDLE_TIMEOUT * adc_dev->channels);
 	/* Wait for Fifo threshold interrupt */
 	while (1) {
@@ -388,7 +391,8 @@ static int tiadc_read_raw(struct iio_dev *indio_dev,
 
 		if (time_after(jiffies, timeout)) {
 			am335x_tsc_se_adc_done(adc_dev->mfd_tscadc);
-			return -EAGAIN;
+			ret = -EAGAIN;
+			goto err_unlock;
 		}
 	}
 	map_val = adc_dev->channel_step[chan->scan_index];
@@ -414,8 +418,11 @@ static int tiadc_read_raw(struct iio_dev *indio_dev,
 	am335x_tsc_se_adc_done(adc_dev->mfd_tscadc);
 
 	if (found == false)
-		return -EBUSY;
-	return IIO_VAL_INT;
+		ret =  -EBUSY;
+
+err_unlock:
+	mutex_unlock(&adc_dev->fifo1_lock);
+	return ret;
 }
 
 static const struct iio_info tiadc_info = {
@@ -483,6 +490,7 @@ static int tiadc_probe(struct platform_device *pdev)
 
 	tiadc_step_config(indio_dev);
 	tiadc_writel(adc_dev, REG_FIFO1THR, FIFO1_THRESHOLD);
+	mutex_init(&adc_dev->fifo1_lock);
 
 	err = tiadc_channel_init(indio_dev, adc_dev->channels);
 	if (err < 0)

drivers/iio/chemical/atlas-ph-sensor.c

@@ -434,7 +434,7 @@ static int atlas_read_raw(struct iio_dev *indio_dev,
 			break;
 		case IIO_ELECTRICALCONDUCTIVITY:
 			*val = 1; /* 0.00001 */
-			*val = 100000;
+			*val2 = 100000;
 			break;
 		case IIO_CONCENTRATION:
 			*val = 0; /* 0.000000001 */

drivers/iio/dac/stx104.c

@@ -65,6 +65,16 @@ struct stx104_gpio {
 	unsigned int out_state;
 };
 
+/**
+ * struct stx104_dev - STX104 device private data structure
+ * @indio_dev:	IIO device
+ * @chip:	instance of the gpio_chip
+ */
+struct stx104_dev {
+	struct iio_dev *indio_dev;
+	struct gpio_chip *chip;
+};
+
 static int stx104_read_raw(struct iio_dev *indio_dev,
 	struct iio_chan_spec const *chan, int *val, int *val2, long mask)
 {
@@ -107,6 +117,7 @@ static const struct iio_chan_spec stx104_channels[STX104_NUM_CHAN] = {
 static int stx104_gpio_get_direction(struct gpio_chip *chip,
 	unsigned int offset)
 {
+	/* GPIO 0-3 are input only, while the rest are output only */
 	if (offset < 4)
 		return 1;
 
@@ -169,6 +180,7 @@ static int stx104_probe(struct device *dev, unsigned int id)
 	struct iio_dev *indio_dev;
 	struct stx104_iio *priv;
 	struct stx104_gpio *stx104gpio;
+	struct stx104_dev *stx104dev;
 	int err;
 
 	indio_dev = devm_iio_device_alloc(dev, sizeof(*priv));
@@ -179,6 +191,10 @@ static int stx104_probe(struct device *dev, unsigned int id)
 	if (!stx104gpio)
 		return -ENOMEM;
 
+	stx104dev = devm_kzalloc(dev, sizeof(*stx104dev), GFP_KERNEL);
+	if (!stx104dev)
+		return -ENOMEM;
+
 	if (!devm_request_region(dev, base[id], STX104_EXTENT,
 		dev_name(dev))) {
 		dev_err(dev, "Unable to lock port addresses (0x%X-0x%X)\n",
@@ -199,12 +215,6 @@ static int stx104_probe(struct device *dev, unsigned int id)
 	outw(0, base[id] + 4);
 	outw(0, base[id] + 6);
 
-	err = devm_iio_device_register(dev, indio_dev);
-	if (err) {
-		dev_err(dev, "IIO device registering failed (%d)\n", err);
-		return err;
-	}
-
 	stx104gpio->chip.label = dev_name(dev);
 	stx104gpio->chip.parent = dev;
 	stx104gpio->chip.owner = THIS_MODULE;
@@ -220,22 +230,32 @@ static int stx104_probe(struct device *dev, unsigned int id)
 
 	spin_lock_init(&stx104gpio->lock);
 
-	dev_set_drvdata(dev, stx104gpio);
+	stx104dev->indio_dev = indio_dev;
+	stx104dev->chip = &stx104gpio->chip;
+	dev_set_drvdata(dev, stx104dev);
 
 	err = gpiochip_add_data(&stx104gpio->chip, stx104gpio);
 	if (err) {
 		dev_err(dev, "GPIO registering failed (%d)\n", err);
 		return err;
 	}
 
+	err = iio_device_register(indio_dev);
+	if (err) {
+		dev_err(dev, "IIO device registering failed (%d)\n", err);
+		gpiochip_remove(&stx104gpio->chip);
+		return err;
+	}
+
 	return 0;
 }
 
 static int stx104_remove(struct device *dev, unsigned int id)
 {
-	struct stx104_gpio *const stx104gpio = dev_get_drvdata(dev);
+	struct stx104_dev *const stx104dev = dev_get_drvdata(dev);
 
-	gpiochip_remove(&stx104gpio->chip);
+	iio_device_unregister(stx104dev->indio_dev);
+	gpiochip_remove(stx104dev->chip);
 
 	return 0;
 }

drivers/iio/humidity/Kconfig

@@ -6,6 +6,8 @@ menu "Humidity sensors"
 config AM2315
     tristate "Aosong AM2315 relative humidity and temperature sensor"
     depends on I2C
+    select IIO_BUFFER
+    select IIO_TRIGGERED_BUFFER
     help
       If you say yes here you get support for the Aosong AM2315
       relative humidity and ambient temperature sensor.

drivers/iio/humidity/am2315.c

@@ -244,7 +244,7 @@ static int am2315_probe(struct i2c_client *client,
 	indio_dev->channels = am2315_channels;
 	indio_dev->num_channels = ARRAY_SIZE(am2315_channels);
 
-	ret = iio_triggered_buffer_setup(indio_dev, NULL,
+	ret = iio_triggered_buffer_setup(indio_dev, iio_pollfunc_store_time,
 					 am2315_trigger_handler, NULL);
 	if (ret < 0) {
 		dev_err(&client->dev, "iio triggered buffer setup failed\n");