diff --git a/sound/pci/ca0106/ca0106.h b/sound/pci/ca0106/ca0106.h
index f246e60942896..991b1c5d41d58 100644
--- a/sound/pci/ca0106/ca0106.h
+++ b/sound/pci/ca0106/ca0106.h
@@ -59,15 +59,15 @@
/* PCI function 0 registers, address = <val> + PCIBASE0 */
/************************************************************************************************/
-#define PTR 0x00 /* Indexed register set pointer register */
+#define CA0106_PTR 0x00 /* Indexed register set pointer register */
/* NOTE: The CHANNELNUM and ADDRESS words can */
/* be modified independently of each other. */
/* CNL[1:0], ADDR[27:16] */
-#define DATA 0x04 /* Indexed register set data register */
+#define CA0106_DATA 0x04 /* Indexed register set data register */
/* DATA[31:0] */
-#define IPR 0x08 /* Global interrupt pending register */
+#define CA0106_IPR 0x08 /* Global interrupt pending register */
/* Clear pending interrupts by writing a 1 to */
/* the relevant bits and zero to the other bits */
#define IPR_MIDI_RX_B 0x00020000 /* MIDI UART-B Receive buffer non-empty */
@@ -88,7 +88,7 @@
#define IPR_MIDI_TX_A 0x00000002 /* MIDI UART-A Transmit buffer empty */
#define IPR_PCI 0x00000001 /* PCI Bus error */
-#define INTE 0x0c /* Interrupt enable register */
+#define CA0106_INTE 0x0c /* Interrupt enable register */
#define INTE_MIDI_RX_B 0x00020000 /* MIDI UART-B Receive buffer non-empty */
#define INTE_MIDI_TX_B 0x00010000 /* MIDI UART-B Transmit buffer empty */
@@ -108,8 +108,8 @@
#define INTE_MIDI_TX_A 0x00000002 /* MIDI UART-A Transmit buffer empty */
#define INTE_PCI 0x00000001 /* PCI Bus error */
-#define UNKNOWN10 0x10 /* Unknown ??. Defaults to 0 */
-#define HCFG 0x14 /* Hardware config register */
+#define CA0106_UNKNOWN10 0x10 /* Unknown ??. Defaults to 0 */
+#define CA0106_HCFG 0x14 /* Hardware config register */
/* 0x1000 causes AC3 to fails. It adds a dither bit. */
#define HCFG_STAC 0x10000000 /* Special mode for STAC9460 Codec. */
@@ -133,7 +133,7 @@
#define HCFG_AUDIOENABLE 0x00000001 /* 0 = CODECs transmit zero-valued samples */
/* Should be set to 1 when the EMU10K1 is */
/* completely initialized. */
-#define GPIO 0x18 /* Defaults: 005f03a3-Analog, 005f02a2-SPDIF. */
+#define CA0106_GPIO 0x18 /* Defaults: 005f03a3-Analog, 005f02a2-SPDIF. */
/* Here pins 0,1,2,3,4,,6 are output. 5,7 are input */
/* For the Audigy LS, pin 0 (or bit 8) controls the SPDIF/Analog jack. */
/* SB Live 24bit:
@@ -152,9 +152,9 @@
* GPO [15:8] Default 0x9. (Default to SPDIF jack enabled for SPDIF)
* GPO Enable [23:16] Default 0x0f. Setting a bit to 1, causes the pin to be an output pin.
*/
-#define AC97DATA 0x1c /* AC97 register set data register (16 bit) */
+#define CA0106_AC97DATA 0x1c /* AC97 register set data register (16 bit) */
-#define AC97ADDRESS 0x1e /* AC97 register set address register (8 bit) */
+#define CA0106_AC97ADDRESS 0x1e /* AC97 register set address register (8 bit) */
/********************************************************************************************************/
/* CA0106 pointer-offset register set, accessed through the PTR and DATA registers */
diff --git a/sound/pci/ca0106/ca0106_main.c b/sound/pci/ca0106/ca0106_main.c
index 36fb150b72fb5..8577f9fa5ea6e 100644
--- a/sound/pci/ca0106/ca0106_main.c
+++ b/sound/pci/ca0106/ca0106_main.c
@@ -338,8 +338,8 @@ unsigned int snd_ca0106_ptr_read(struct snd_ca0106 * emu,
regptr = (reg << 16) | chn;
spin_lock_irqsave(&emu->emu_lock, flags);
- outl(regptr, emu->port + PTR);
- val = inl(emu->port + DATA);
+ outl(regptr, emu->port + CA0106_PTR);
+ val = inl(emu->port + CA0106_DATA);
spin_unlock_irqrestore(&emu->emu_lock, flags);
return val;
}
@@ -355,8 +355,8 @@ void snd_ca0106_ptr_write(struct snd_ca0106 *emu,
regptr = (reg << 16) | chn;
spin_lock_irqsave(&emu->emu_lock, flags);
- outl(regptr, emu->port + PTR);
- outl(data, emu->port + DATA);
+ outl(regptr, emu->port + CA0106_PTR);
+ outl(data, emu->port + CA0106_DATA);
spin_unlock_irqrestore(&emu->emu_lock, flags);
}
@@ -455,8 +455,8 @@ static void snd_ca0106_intr_enable(struct snd_ca0106 *emu, unsigned int intrenb)
unsigned int intr_enable;
spin_lock_irqsave(&emu->emu_lock, flags);
- intr_enable = inl(emu->port + INTE) | intrenb;
- outl(intr_enable, emu->port + INTE);
+ intr_enable = inl(emu->port + CA0106_INTE) | intrenb;
+ outl(intr_enable, emu->port + CA0106_INTE);
spin_unlock_irqrestore(&emu->emu_lock, flags);
}
@@ -466,8 +466,8 @@ static void snd_ca0106_intr_disable(struct snd_ca0106 *emu, unsigned int intrenb
unsigned int intr_enable;
spin_lock_irqsave(&emu->emu_lock, flags);
- intr_enable = inl(emu->port + INTE) & ~intrenb;
- outl(intr_enable, emu->port + INTE);
+ intr_enable = inl(emu->port + CA0106_INTE) & ~intrenb;
+ outl(intr_enable, emu->port + CA0106_INTE);
spin_unlock_irqrestore(&emu->emu_lock, flags);
}
@@ -786,9 +786,9 @@ static int snd_ca0106_pcm_prepare_playback(struct snd_pcm_substream *substream)
hcfg_set = 0;
break;
}
- hcfg = inl(emu->port + HCFG) ;
+ hcfg = inl(emu->port + CA0106_HCFG) ;
hcfg = (hcfg & ~hcfg_mask) | hcfg_set;
- outl(hcfg, emu->port + HCFG);
+ outl(hcfg, emu->port + CA0106_HCFG);
reg40 = snd_ca0106_ptr_read(emu, 0x40, 0);
reg40 = (reg40 & ~reg40_mask) | reg40_set;
snd_ca0106_ptr_write(emu, 0x40, 0, reg40);
@@ -888,9 +888,9 @@ static int snd_ca0106_pcm_prepare_capture(struct snd_pcm_substream *substream)
hcfg_set = 0;
break;
}
- hcfg = inl(emu->port + HCFG) ;
+ hcfg = inl(emu->port + CA0106_HCFG) ;
hcfg = (hcfg & ~hcfg_mask) | hcfg_set;
- outl(hcfg, emu->port + HCFG);
+ outl(hcfg, emu->port + CA0106_HCFG);
reg71 = snd_ca0106_ptr_read(emu, 0x71, 0);
reg71 = (reg71 & ~reg71_mask) | reg71_set;
snd_ca0106_ptr_write(emu, 0x71, 0, reg71);
@@ -1142,8 +1142,8 @@ static unsigned short snd_ca0106_ac97_read(struct snd_ac97 *ac97,
unsigned short val;
spin_lock_irqsave(&emu->emu_lock, flags);
- outb(reg, emu->port + AC97ADDRESS);
- val = inw(emu->port + AC97DATA);
+ outb(reg, emu->port + CA0106_AC97ADDRESS);
+ val = inw(emu->port + CA0106_AC97DATA);
spin_unlock_irqrestore(&emu->emu_lock, flags);
return val;
}
@@ -1155,8 +1155,8 @@ static void snd_ca0106_ac97_write(struct snd_ac97 *ac97,
unsigned long flags;
spin_lock_irqsave(&emu->emu_lock, flags);
- outb(reg, emu->port + AC97ADDRESS);
- outw(val, emu->port + AC97DATA);
+ outb(reg, emu->port + CA0106_AC97ADDRESS);
+ outw(val, emu->port + CA0106_AC97DATA);
spin_unlock_irqrestore(&emu->emu_lock, flags);
}
@@ -1200,7 +1200,7 @@ static irqreturn_t snd_ca0106_interrupt(int irq, void *dev_id)
unsigned int stat76;
struct snd_ca0106_channel *pchannel;
- status = inl(chip->port + IPR);
+ status = inl(chip->port + CA0106_IPR);
if (! status)
return IRQ_NONE;
@@ -1255,7 +1255,7 @@ static irqreturn_t snd_ca0106_interrupt(int irq, void *dev_id)
}
// acknowledge the interrupt if necessary
- outl(status, chip->port+IPR);
+ outl(status, chip->port + CA0106_IPR);
return IRQ_HANDLED;
}
@@ -1383,7 +1383,7 @@ static void ca0106_init_chip(struct snd_ca0106 *chip, int resume)
int ch;
unsigned int def_bits;
- outl(0, chip->port + INTE);
+ outl(0, chip->port + CA0106_INTE);
/*
* Init to 0x02109204 :
@@ -1420,8 +1420,8 @@ static void ca0106_init_chip(struct snd_ca0106 *chip, int resume)
snd_ca0106_ptr_write(chip, CAPTURE_MUTE, 0, 0x00fc0000);
/* Write 0x8000 to AC97_REC_GAIN to mute it. */
- outb(AC97_REC_GAIN, chip->port + AC97ADDRESS);
- outw(0x8000, chip->port + AC97DATA);
+ outb(AC97_REC_GAIN, chip->port + CA0106_AC97ADDRESS);
+ outw(0x8000, chip->port + CA0106_AC97DATA);
#if 0 /* FIXME: what are these? */
snd_ca0106_ptr_write(chip, SPCS0, 0, 0x2108006);
snd_ca0106_ptr_write(chip, 0x42, 0, 0x2108006);
@@ -1495,30 +1495,30 @@ static void ca0106_init_chip(struct snd_ca0106 *chip, int resume)
/* FIXME: Still need to find out what the other GPIO bits do.
* E.g. For digital spdif out.
*/
- outl(0x0, chip->port+GPIO);
- /* outl(0x00f0e000, chip->port+GPIO); */ /* Analog */
- outl(0x005f5301, chip->port+GPIO); /* Analog */
+ outl(0x0, chip->port + CA0106_GPIO);
+ /* outl(0x00f0e000, chip->port + CA0106_GPIO); */ /* Analog */
+ outl(0x005f5301, chip->port + CA0106_GPIO); /* Analog */
} else if (chip->details->gpio_type == 1) {
/* The SB0410 and SB0413 use GPIO differently. */
/* FIXME: Still need to find out what the other GPIO bits do.
* E.g. For digital spdif out.
*/
- outl(0x0, chip->port+GPIO);
- /* outl(0x00f0e000, chip->port+GPIO); */ /* Analog */
- outl(0x005f5301, chip->port+GPIO); /* Analog */
+ outl(0x0, chip->port + CA0106_GPIO);
+ /* outl(0x00f0e000, chip->port + CA0106_GPIO); */ /* Analog */
+ outl(0x005f5301, chip->port + CA0106_GPIO); /* Analog */
} else {
- outl(0x0, chip->port+GPIO);
- outl(0x005f03a3, chip->port+GPIO); /* Analog */
- /* outl(0x005f02a2, chip->port+GPIO); */ /* SPDIF */
+ outl(0x0, chip->port + CA0106_GPIO);
+ outl(0x005f03a3, chip->port + CA0106_GPIO); /* Analog */
+ /* outl(0x005f02a2, chip->port + CA0106_GPIO); */ /* SPDIF */
}
snd_ca0106_intr_enable(chip, 0x105); /* Win2000 uses 0x1e0 */
/* outl(HCFG_LOCKSOUNDCACHE|HCFG_AUDIOENABLE, chip->port+HCFG); */
/* 0x1000 causes AC3 to fails. Maybe it effects 24 bit output. */
- /* outl(0x00001409, chip->port+HCFG); */
- /* outl(0x00000009, chip->port+HCFG); */
+ /* outl(0x00001409, chip->port + CA0106_HCFG); */
+ /* outl(0x00000009, chip->port + CA0106_HCFG); */
/* AC97 2.0, Enable outputs. */
- outl(HCFG_AC97 | HCFG_AUDIOENABLE, chip->port+HCFG);
+ outl(HCFG_AC97 | HCFG_AUDIOENABLE, chip->port + CA0106_HCFG);
if (chip->details->i2c_adc == 1) {
/* The SB0410 and SB0413 use I2C to control ADC. */
@@ -1560,12 +1560,12 @@ static void ca0106_stop_chip(struct snd_ca0106 *chip)
{
/* disable interrupts */
snd_ca0106_ptr_write(chip, BASIC_INTERRUPT, 0, 0);
- outl(0, chip->port + INTE);
+ outl(0, chip->port + CA0106_INTE);
snd_ca0106_ptr_write(chip, EXTENDED_INT_MASK, 0, 0);
udelay(1000);
/* disable audio */
/* outl(HCFG_LOCKSOUNDCACHE, chip->port + HCFG); */
- outl(0, chip->port + HCFG);
+ outl(0, chip->port + CA0106_HCFG);
/* FIXME: We need to stop and DMA transfers here.
* But as I am not sure how yet, we cannot from the dma pages.
* So we can fix: snd-malloc: Memory leak? pages not freed = 8
diff --git a/sound/pci/ca0106/ca0106_mixer.c b/sound/pci/ca0106/ca0106_mixer.c
index c852c6a75b917..05f56015ddd87 100644
--- a/sound/pci/ca0106/ca0106_mixer.c
+++ b/sound/pci/ca0106/ca0106_mixer.c
@@ -70,8 +70,8 @@ static void ca0106_spdif_enable(struct snd_ca0106 *emu)
snd_ca0106_ptr_write(emu, SPDIF_SELECT2, 0, 0x0b000000);
val = snd_ca0106_ptr_read(emu, CAPTURE_CONTROL, 0) & ~0x1000;
snd_ca0106_ptr_write(emu, CAPTURE_CONTROL, 0, val);
- val = inl(emu->port + GPIO) & ~0x101;
- outl(val, emu->port + GPIO);
+ val = inl(emu->port + CA0106_GPIO) & ~0x101;
+ outl(val, emu->port + CA0106_GPIO);
} else {
/* Analog */
@@ -79,8 +79,8 @@ static void ca0106_spdif_enable(struct snd_ca0106 *emu)
snd_ca0106_ptr_write(emu, SPDIF_SELECT2, 0, 0x000f0000);
val = snd_ca0106_ptr_read(emu, CAPTURE_CONTROL, 0) | 0x1000;
snd_ca0106_ptr_write(emu, CAPTURE_CONTROL, 0, val);
- val = inl(emu->port + GPIO) | 0x101;
- outl(val, emu->port + GPIO);
+ val = inl(emu->port + CA0106_GPIO) | 0x101;
+ outl(val, emu->port + CA0106_GPIO);
}
}
@@ -119,14 +119,14 @@ static void ca0106_set_capture_mic_line_in(struct snd_ca0106 *emu)
if (emu->capture_mic_line_in) {
/* snd_ca0106_i2c_write(emu, ADC_MUX, 0); */ /* Mute input */
- tmp = inl(emu->port+GPIO) & ~0x400;
+ tmp = inl(emu->port + CA0106_GPIO) & ~0x400;
tmp = tmp | 0x400;
- outl(tmp, emu->port+GPIO);
+ outl(tmp, emu->port + CA0106_GPIO);
/* snd_ca0106_i2c_write(emu, ADC_MUX, ADC_MUX_MIC); */
} else {
/* snd_ca0106_i2c_write(emu, ADC_MUX, 0); */ /* Mute input */
- tmp = inl(emu->port+GPIO) & ~0x400;
- outl(tmp, emu->port+GPIO);
+ tmp = inl(emu->port + CA0106_GPIO) & ~0x400;
+ outl(tmp, emu->port + CA0106_GPIO);
/* snd_ca0106_i2c_write(emu, ADC_MUX, ADC_MUX_LINEIN); */
}
}