---

yaml
---
r: 107367
b: refs/heads/master
c: 6c5e0c4
h: refs/heads/master
i:
  107365: 6846958
  107363: 45adcbb
  107359: bbca085
v: v3

[refs]

@@ -1,2 +1,2 @@
 ---
-refs/heads/master: 31582b094d640fdab3fd29237b348a4c7c8646fb
+refs/heads/master: 6c5e0c4d518a37e1d5d794c14433e80284415079

trunk/Documentation/DocBook/kgdb.tmpl

@@ -98,24 +98,6 @@
     "Kernel debugging" select "KGDB: kernel debugging with remote gdb".
     </para>
     <para>
-    It is advised, but not required that you turn on the
-    CONFIG_FRAME_POINTER kernel option.  This option inserts code to
-    into the compiled executable which saves the frame information in
-    registers or on the stack at different points which will allow a
-    debugger such as gdb to more accurately construct stack back traces
-    while debugging the kernel.
-    </para>
-    <para>
-    If the architecture that you are using supports the kernel option
-    CONFIG_DEBUG_RODATA, you should consider turning it off.  This
-    option will prevent the use of software breakpoints because it
-    marks certain regions of the kernel's memory space as read-only.
-    If kgdb supports it for the architecture you are using, you can
-    use hardware breakpoints if you desire to run with the
-    CONFIG_DEBUG_RODATA option turned on, else you need to turn off
-    this option.
-    </para>
-    <para>
     Next you should choose one of more I/O drivers to interconnect debugging
     host and debugged target.  Early boot debugging requires a KGDB
     I/O driver that supports early debugging and the driver must be

trunk/Documentation/hwmon/dme1737

@@ -22,10 +22,6 @@ Module Parameters
 			and PWM output control functions. Using this parameter
 			shouldn't be required since the BIOS usually takes care
 			of this.
-* probe_all_addr: bool	Include non-standard LPC addresses 0x162e and 0x164e
-			when probing for ISA devices. This is required for the
-			following boards:
-			- VIA EPIA SN18000
 
 Note that there is no need to use this parameter if the driver loads without
 complaining. The driver will say so if it is necessary.

trunk/Documentation/hwmon/lm85

@@ -96,6 +96,11 @@ initial testing of the ADM1027 it was 1.00 degC steps. Analog Devices has
 confirmed this "bug". The ADT7463 is reported to work as described in the
 documentation. The current lm85 driver does not show the offset register.
 
+The ADT7463 has a THERM asserted counter. This counter has a 22.76ms
+resolution and a range of 5.8 seconds. The driver implements a 32-bit
+accumulator of the counter value to extend the range to over a year. The
+counter will stay at it's max value until read.
+
 See the vendor datasheets for more information. There is application note
 from National (AN-1260) with some additional information about the LM85.
 The Analog Devices datasheet is very detailed and describes a procedure for
@@ -201,15 +206,13 @@ Configuration choices:
 
 The National LM85's have two vendor specific configuration
 features. Tach. mode and Spinup Control. For more details on these,
-see the LM85 datasheet or Application Note AN-1260. These features
-are not currently supported by the lm85 driver.
+see the LM85 datasheet or Application Note AN-1260.
 
 The Analog Devices ADM1027 has several vendor specific enhancements.
 The number of pulses-per-rev of the fans can be set, Tach monitoring
 can be optimized for PWM operation, and an offset can be applied to
 the temperatures to compensate for systemic errors in the
-measurements. These features are not currently supported by the lm85
-driver.
+measurements.
 
 In addition to the ADM1027 features, the ADT7463 also has Tmin control
 and THERM asserted counts. Automatic Tmin control acts to adjust the

trunk/Documentation/power/power_supply_class.txt

@@ -101,10 +101,6 @@ of charge when battery became full/empty". It also could mean "value of
 charge when battery considered full/empty at given conditions (temperature,
 age)". I.e. these attributes represents real thresholds, not design values.
 
-CHARGE_COUNTER - the current charge counter (in µAh).  This could easily
-be negative; there is no empty or full value.  It is only useful for
-relative, time-based measurements.
-
 ENERGY_FULL, ENERGY_EMPTY - same as above but for energy.
 
 CAPACITY - capacity in percents.