---

yaml
---
r: 280117
b: refs/heads/master
c: d0ad5e8
h: refs/heads/master
i:
  280115: 1d5ff38
v: v3

[refs]

@@ -1,2 +1,2 @@
 ---
-refs/heads/master: 6f61415e9c4c0ab02c8eda7671bb652db4863cc0
+refs/heads/master: d0ad5e89256c351ddd40167152c24a88efcb0f6d

trunk/drivers/gpio/gpio-wm8994.c

@@ -117,6 +117,60 @@ static int wm8994_gpio_to_irq(struct gpio_chip *chip, unsigned offset)
 
 
 #ifdef CONFIG_DEBUG_FS
+static const char *wm8994_gpio_fn(u16 fn)
+{
+	switch (fn) {
+	case WM8994_GP_FN_PIN_SPECIFIC:
+		return "pin-specific";
+	case WM8994_GP_FN_GPIO:
+		return "GPIO";
+	case WM8994_GP_FN_SDOUT:
+		return "SDOUT";
+	case WM8994_GP_FN_IRQ:
+		return "IRQ";
+	case WM8994_GP_FN_TEMPERATURE:
+		return "Temperature";
+	case WM8994_GP_FN_MICBIAS1_DET:
+		return "MICBIAS1 detect";
+	case WM8994_GP_FN_MICBIAS1_SHORT:
+		return "MICBIAS1 short";
+	case WM8994_GP_FN_MICBIAS2_DET:
+		return "MICBIAS2 detect";
+	case WM8994_GP_FN_MICBIAS2_SHORT:
+		return "MICBIAS2 short";
+	case WM8994_GP_FN_FLL1_LOCK:
+		return "FLL1 lock";
+	case WM8994_GP_FN_FLL2_LOCK:
+		return "FLL2 lock";
+	case WM8994_GP_FN_SRC1_LOCK:
+		return "SRC1 lock";
+	case WM8994_GP_FN_SRC2_LOCK:
+		return "SRC2 lock";
+	case WM8994_GP_FN_DRC1_ACT:
+		return "DRC1 activity";
+	case WM8994_GP_FN_DRC2_ACT:
+		return "DRC2 activity";
+	case WM8994_GP_FN_DRC3_ACT:
+		return "DRC3 activity";
+	case WM8994_GP_FN_WSEQ_STATUS:
+		return "Write sequencer";
+	case WM8994_GP_FN_FIFO_ERROR:
+		return "FIFO error";
+	case WM8994_GP_FN_OPCLK:
+		return "OPCLK";
+	case WM8994_GP_FN_THW:
+		return "Thermal warning";
+	case WM8994_GP_FN_DCS_DONE:
+		return "DC servo";
+	case WM8994_GP_FN_FLL1_OUT:
+		return "FLL1 output";
+	case WM8994_GP_FN_FLL2_OUT:
+		return "FLL1 output";
+	default:
+		return "Unknown";
+	}
+}
+
 static void wm8994_gpio_dbg_show(struct seq_file *s, struct gpio_chip *chip)
 {
 	struct wm8994_gpio *wm8994_gpio = to_wm8994_gpio(chip);
@@ -148,8 +202,29 @@ static void wm8994_gpio_dbg_show(struct seq_file *s, struct gpio_chip *chip)
 			continue;
 		}
 
-		/* No decode yet; note that GPIO2 is special */
-		seq_printf(s, "(%x)\n", reg);
+		if (reg & WM8994_GPN_DIR)
+			seq_printf(s, "in ");
+		else
+			seq_printf(s, "out ");
+
+		if (reg & WM8994_GPN_PU)
+			seq_printf(s, "pull up ");
+
+		if (reg & WM8994_GPN_PD)
+			seq_printf(s, "pull down ");
+
+		if (reg & WM8994_GPN_POL)
+			seq_printf(s, "inverted ");
+		else
+			seq_printf(s, "noninverted ");
+
+		if (reg & WM8994_GPN_OP_CFG)
+			seq_printf(s, "open drain ");
+		else
+			seq_printf(s, "CMOS ");
+
+		seq_printf(s, "%s (%x)\n",
+			   wm8994_gpio_fn(reg & WM8994_GPN_FN_MASK), reg);
 	}
 }
 #else