---

yaml
---
r: 310496
b: refs/heads/master
c: ae58d1e
h: refs/heads/master
v: v3

[refs]

@@ -1,2 +1,2 @@
 ---
-refs/heads/master: 5698e9180cb70020bbf8b613174afe6308f902b0
+refs/heads/master: ae58d1e406986f31d1e88b32f5ac601506c196d8

trunk/Documentation/devicetree/bindings/i2c/i2c-mux-pinctrl.txt

@@ -0,0 +1,93 @@
+Pinctrl-based I2C Bus Mux
+
+This binding describes an I2C bus multiplexer that uses pin multiplexing to
+route the I2C signals, and represents the pin multiplexing configuration
+using the pinctrl device tree bindings.
+
+                                 +-----+  +-----+
+                                 | dev |  | dev |
+    +------------------------+   +-----+  +-----+
+    | SoC                    |      |        |
+    |                   /----|------+--------+
+    |   +---+   +------+     | child bus A, on first set of pins
+    |   |I2C|---|Pinmux|     |
+    |   +---+   +------+     | child bus B, on second set of pins
+    |                   \----|------+--------+--------+
+    |                        |      |        |        |
+    +------------------------+  +-----+  +-----+  +-----+
+                                | dev |  | dev |  | dev |
+                                +-----+  +-----+  +-----+
+
+Required properties:
+- compatible: i2c-mux-pinctrl
+- i2c-parent: The phandle of the I2C bus that this multiplexer's master-side
+  port is connected to.
+
+Also required are:
+
+* Standard pinctrl properties that specify the pin mux state for each child
+  bus. See ../pinctrl/pinctrl-bindings.txt.
+
+* Standard I2C mux properties. See mux.txt in this directory.
+
+* I2C child bus nodes. See mux.txt in this directory.
+
+For each named state defined in the pinctrl-names property, an I2C child bus
+will be created. I2C child bus numbers are assigned based on the index into
+the pinctrl-names property.
+
+The only exception is that no bus will be created for a state named "idle". If
+such a state is defined, it must be the last entry in pinctrl-names. For
+example:
+
+	pinctrl-names = "ddc", "pta", "idle"  ->  ddc = bus 0, pta = bus 1
+	pinctrl-names = "ddc", "idle", "pta"  ->  Invalid ("idle" not last)
+	pinctrl-names = "idle", "ddc", "pta"  ->  Invalid ("idle" not last)
+
+Whenever an access is made to a device on a child bus, the relevant pinctrl
+state will be programmed into hardware.
+
+If an idle state is defined, whenever an access is not being made to a device
+on a child bus, the idle pinctrl state will be programmed into hardware.
+
+If an idle state is not defined, the most recently used pinctrl state will be
+left programmed into hardware whenever no access is being made of a device on
+a child bus.
+
+Example:
+
+	i2cmux {
+		compatible = "i2c-mux-pinctrl";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		i2c-parent = <&i2c1>;
+
+		pinctrl-names = "ddc", "pta", "idle";
+		pinctrl-0 = <&state_i2cmux_ddc>;
+		pinctrl-1 = <&state_i2cmux_pta>;
+		pinctrl-2 = <&state_i2cmux_idle>;
+
+		i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			eeprom {
+				compatible = "eeprom";
+				reg = <0x50>;
+			};
+		};
+
+		i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			eeprom {
+				compatible = "eeprom";
+				reg = <0x50>;
+			};
+		};
+	};
+

trunk/Documentation/kernel-parameters.txt

@@ -2543,15 +2543,6 @@ bytes respectively. Such letter suffixes can also be entirely omitted.
 
 	sched_debug	[KNL] Enables verbose scheduler debug messages.
 
-	skew_tick=	[KNL] Offset the periodic timer tick per cpu to mitigate
-			xtime_lock contention on larger systems, and/or RCU lock
-			contention on all systems with CONFIG_MAXSMP set.
-			Format: { "0" | "1" }
-			0 -- disable. (may be 1 via CONFIG_CMDLINE="skew_tick=1"
-			1 -- enable.
-			Note: increases power consumption, thus should only be
-			enabled if running jitter sensitive (HPC/RT) workloads.
-
 	security=	[SECURITY] Choose a security module to enable at boot.
 			If this boot parameter is not specified, only the first
 			security module asking for security registration will be