---

yaml
---
r: 332488
b: refs/heads/master
c: 9e2d865
h: refs/heads/master
v: v3

[refs]

@@ -1,2 +1,2 @@
 ---
-refs/heads/master: 9e695d2ecc8451cc2c1603d60b5c8e7f5581923a
+refs/heads/master: 9e2d8656f5e8aa214e66b462680cf86b210b74a8

trunk/Documentation/devicetree/bindings/pinctrl/lantiq,falcon-pinumx.txt

@@ -0,0 +1,83 @@
+Lantiq FALCON pinmux controller
+
+Required properties:
+- compatible: "lantiq,pinctrl-falcon"
+- reg: Should contain the physical address and length of the gpio/pinmux
+  register range
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+Lantiq's pin configuration nodes act as a container for an abitrary number of
+subnodes. Each of these subnodes represents some desired configuration for a
+pin, a group, or a list of pins or groups. This configuration can include the
+mux function to select on those group(s), and two pin configuration parameters:
+pull-up and open-drain
+
+The name of each subnode is not important as long as it is unique; all subnodes
+should be enumerated and processed purely based on their content.
+
+Each subnode only affects those parameters that are explicitly listed. In
+other words, a subnode that lists a mux function but no pin configuration
+parameters implies no information about any pin configuration parameters.
+Similarly, a pin subnode that describes a pullup parameter implies no
+information about e.g. the mux function.
+
+We support 2 types of nodes.
+
+Definition of mux function groups:
+
+Required subnode-properties:
+- lantiq,groups : An array of strings. Each string contains the name of a group.
+  Valid values for these names are listed below.
+- lantiq,function: A string containing the name of the function to mux to the
+  group. Valid values for function names are listed below.
+
+Valid values for group and function names:
+
+  mux groups:
+    por, ntr, ntr8k, hrst, mdio, bootled, asc0, spi, spi cs0, spi cs1, i2c,
+    jtag, slic, pcm, asc1
+
+  functions:
+    rst, ntr, mdio, led, asc, spi, i2c, jtag, slic, pcm
+
+
+Definition of pin configurations:
+
+Required subnode-properties:
+- lantiq,pins : An array of strings. Each string contains the name of a pin.
+  Valid values for these names are listed below.
+
+Optional subnode-properties:
+- lantiq,pull: Integer, representing the pull-down/up to apply to the pin.
+    0: none, 1: down
+- lantiq,drive-current: Boolean, enables drive-current
+- lantiq,slew-rate: Boolean, enables slew-rate
+
+Example:
+	pinmux0 {
+		compatible = "lantiq,pinctrl-falcon";
+		pinctrl-names = "default";
+		pinctrl-0 = <&state_default>;
+
+		state_default: pinmux {
+			asc0 {
+				lantiq,groups = "asc0";
+				lantiq,function = "asc";
+			};
+			ntr {
+				lantiq,groups = "ntr8k";
+				lantiq,function = "ntr";
+			};
+			i2c {
+				lantiq,groups = "i2c";
+				lantiq,function = "i2c";
+			};
+			hrst {
+				lantiq,groups = "hrst";
+				lantiq,function = "rst";
+			};
+		};
+	};

trunk/Documentation/devicetree/bindings/pinctrl/lantiq,xway-pinumx.txt

@@ -0,0 +1,97 @@
+Lantiq XWAY pinmux controller
+
+Required properties:
+- compatible: "lantiq,pinctrl-xway" or "lantiq,pinctrl-xr9"
+- reg: Should contain the physical address and length of the gpio/pinmux
+  register range
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+Lantiq's pin configuration nodes act as a container for an abitrary number of
+subnodes. Each of these subnodes represents some desired configuration for a
+pin, a group, or a list of pins or groups. This configuration can include the
+mux function to select on those group(s), and two pin configuration parameters:
+pull-up and open-drain
+
+The name of each subnode is not important as long as it is unique; all subnodes
+should be enumerated and processed purely based on their content.
+
+Each subnode only affects those parameters that are explicitly listed. In
+other words, a subnode that lists a mux function but no pin configuration
+parameters implies no information about any pin configuration parameters.
+Similarly, a pin subnode that describes a pullup parameter implies no
+information about e.g. the mux function.
+
+We support 2 types of nodes.
+
+Definition of mux function groups:
+
+Required subnode-properties:
+- lantiq,groups : An array of strings. Each string contains the name of a group.
+  Valid values for these names are listed below.
+- lantiq,function: A string containing the name of the function to mux to the
+  group. Valid values for function names are listed below.
+
+Valid values for group and function names:
+
+  mux groups:
+    exin0, exin1, exin2, jtag, ebu a23, ebu a24, ebu a25, ebu clk, ebu cs1,
+    ebu wait, nand ale, nand cs1, nand cle, spi, spi_cs1, spi_cs2, spi_cs3,
+    spi_cs4, spi_cs5, spi_cs6, asc0, asc0 cts rts, stp, nmi , gpt1, gpt2,
+    gpt3, clkout0, clkout1, clkout2, clkout3, gnt1, gnt2, gnt3, req1, req2,
+    req3
+
+  additional mux groups (XR9 only):
+    mdio, nand rdy, nand rd, exin3, exin4, gnt4, req4
+
+  functions:
+    spi, asc, cgu, jtag, exin, stp, gpt, nmi, pci, ebu, mdio
+
+
+
+Definition of pin configurations:
+
+Required subnode-properties:
+- lantiq,pins : An array of strings. Each string contains the name of a pin.
+  Valid values for these names are listed below.
+
+Optional subnode-properties:
+- lantiq,pull: Integer, representing the pull-down/up to apply to the pin.
+    0: none, 1: down, 2: up.
+- lantiq,open-drain: Boolean, enables open-drain on the defined pin.
+
+Valid values for XWAY pin names:
+  Pinconf pins can be referenced via the names io0-io31.
+
+Valid values for XR9 pin names:
+  Pinconf pins can be referenced via the names io0-io55.
+
+Example:
+	gpio: pinmux@E100B10 {
+		compatible = "lantiq,pinctrl-xway";
+		pinctrl-names = "default";
+		pinctrl-0 = <&state_default>;
+
+		#gpio-cells = <2>;
+		gpio-controller;
+		reg = <0xE100B10 0xA0>;
+
+		state_default: pinmux {
+			stp {
+				lantiq,groups = "stp";
+				lantiq,function = "stp";
+			};
+			pci {
+				lantiq,groups = "gnt1";
+				lantiq,function = "pci";
+			};
+			conf_out {
+				lantiq,pins = "io4", "io5", "io6"; /* stp */
+				lantiq,open-drain;
+				lantiq,pull = <0>;
+			};
+		};
+	};
+

trunk/Documentation/devicetree/bindings/spi/spi-octeon.txt

@@ -0,0 +1,33 @@
+Cavium, Inc. OCTEON SOC SPI master controller.
+
+Required properties:
+- compatible : "cavium,octeon-3010-spi"
+- reg : The register base for the controller.
+- interrupts : One interrupt, used by the controller.
+- #address-cells : <1>, as required by generic SPI binding.
+- #size-cells : <0>, also as required by generic SPI binding.
+
+Child nodes as per the generic SPI binding.
+
+Example:
+
+	spi@1070000001000 {
+		compatible = "cavium,octeon-3010-spi";
+		reg = <0x10700 0x00001000 0x0 0x100>;
+		interrupts = <0 58>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		eeprom@0 {
+			compatible = "st,m95256", "atmel,at25";
+			reg = <0>;
+			spi-max-frequency = <5000000>;
+			spi-cpha;
+			spi-cpol;
+
+			pagesize = <64>;
+			size = <32768>;
+			address-width = <16>;
+		};
+	};
+

trunk/MAINTAINERS

@@ -7178,6 +7178,8 @@ F:	drivers/char/tlclk.c
 
 TENSILICA XTENSA PORT (xtensa)
 M:	Chris Zankel <chris@zankel.net>
+M:	Max Filippov <jcmvbkbc@gmail.com>
+L:	linux-xtensa@linux-xtensa.org
 S:	Maintained
 F:	arch/xtensa/
 

trunk/arch/alpha/include/asm/Kbuild

@@ -1,5 +1,7 @@
 include include/asm-generic/Kbuild.asm
 
+generic-y += clkdev.h
+
 header-y += compiler.h
 header-y += console.h
 header-y += fpu.h

trunk/arch/avr32/include/asm/Kbuild

@@ -1,3 +1,5 @@
 include include/asm-generic/Kbuild.asm
 
+generic-y	+= clkdev.h
+
 header-y	+= cachectl.h

trunk/arch/blackfin/Kconfig

@@ -299,7 +299,7 @@ config BF_REV_0_3
 
 config BF_REV_0_4
 	bool "0.4"
-	depends on (BF561 || BF533 || BF532 || BF531 || BF538 || BF539)
+	depends on (BF561 || BF533 || BF532 || BF531 || BF538 || BF539 || BF54x)
 
 config BF_REV_0_5
 	bool "0.5"

trunk/arch/blackfin/configs/BF533-EZKIT_defconfig

@@ -52,10 +52,13 @@ CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
 CONFIG_MTD=y
 CONFIG_MTD_CHAR=m
 CONFIG_MTD_BLOCK=y
-CONFIG_MTD_JEDECPROBE=m
+CONFIG_MTD_JEDECPROBE=y
+CONFIG_MTD_CFI_AMDSTD=y
 CONFIG_MTD_RAM=y
-CONFIG_MTD_ROM=m
+CONFIG_MTD_ROM=y
 CONFIG_MTD_COMPLEX_MAPPINGS=y
+CONFIG_MTD_PHYSMAP=y
+CONFIG_MTD_PLATRAM=y
 CONFIG_BLK_DEV_RAM=y
 CONFIG_NETDEVICES=y
 # CONFIG_NET_VENDOR_BROADCOM is not set

trunk/arch/blackfin/configs/BF609-EZKIT_defconfig

@@ -1,5 +1,6 @@
 CONFIG_EXPERIMENTAL=y
 CONFIG_SYSVIPC=y
+CONFIG_HIGH_RES_TIMERS=y
 CONFIG_IKCONFIG=y
 CONFIG_IKCONFIG_PROC=y
 CONFIG_LOG_BUF_SHIFT=14
@@ -24,7 +25,6 @@ CONFIG_BF609=y
 CONFIG_PINT1_ASSIGN=0x01010000
 CONFIG_PINT2_ASSIGN=0x07000101
 CONFIG_PINT3_ASSIGN=0x02020303
-CONFIG_HIGH_RES_TIMERS=y
 CONFIG_IP_CHECKSUM_L1=y
 CONFIG_SYSCALL_TAB_L1=y
 CONFIG_CPLB_SWITCH_TAB_L1=y
@@ -116,9 +116,6 @@ CONFIG_SND_PCM_OSS=m
 # CONFIG_SND_SPI is not set
 # CONFIG_SND_USB is not set
 CONFIG_SND_SOC=m
-CONFIG_SND_BF6XX_I2S=m
-CONFIG_SND_SOC_BFIN_EVAL_ADAU1X61=m
-CONFIG_SND_SOC_ALL_CODECS=m
 CONFIG_USB=y
 CONFIG_USB_MUSB_HDRC=y
 CONFIG_USB_MUSB_BLACKFIN=m
@@ -136,7 +133,6 @@ CONFIG_VFAT_FS=y
 CONFIG_JFFS2_FS=m
 CONFIG_UBIFS_FS=m
 CONFIG_NFS_FS=m
-CONFIG_NFS_V3=y
 CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_ISO8859_1=y
 CONFIG_DEBUG_FS=y
@@ -149,9 +145,9 @@ CONFIG_DEBUG_BFIN_HWTRACE_COMPRESSION_ONE=y
 CONFIG_EARLY_PRINTK=y
 CONFIG_CPLB_INFO=y
 CONFIG_BFIN_PSEUDODBG_INSNS=y
-CONFIG_CRYPTO_HMAC=y
-CONFIG_CRYPTO_MD4=y
-CONFIG_CRYPTO_MD5=y
-CONFIG_CRYPTO_ARC4=y
+CONFIG_CRYPTO_HMAC=m
+CONFIG_CRYPTO_MD4=m
+CONFIG_CRYPTO_MD5=m
+CONFIG_CRYPTO_ARC4=m
 # CONFIG_CRYPTO_ANSI_CPRNG is not set
-CONFIG_CRYPTO_DEV_BFIN_CRC=y
+CONFIG_CRYPTO_DEV_BFIN_CRC=m

trunk/arch/blackfin/kernel/bfin_gpio.c

@@ -1265,8 +1265,8 @@ static __init int gpio_register_proc(void)
 {
 	struct proc_dir_entry *proc_gpio;
 
-	proc_gpio = proc_create("gpio", S_IRUGO, NULL, &gpio_proc_ops);
-	return proc_gpio != NULL;
+	proc_gpio = proc_create("gpio", 0, NULL, &gpio_proc_ops);
+	return proc_gpio == NULL;
 }
 __initcall(gpio_register_proc);
 #endif

trunk/arch/blackfin/kernel/reboot.c

@@ -86,7 +86,6 @@ void native_machine_restart(char *cmd)
 void machine_restart(char *cmd)
 {
 	native_machine_restart(cmd);
-	local_irq_disable();
 	if (smp_processor_id())
 		smp_call_function((void *)bfin_reset, 0, 1);
 	else