Merge branch 'topic/xilinx' into for-linus

Documentation/devicetree/bindings/dma/xilinx/xilinx_vdma.txt

@@ -0,0 +1,75 @@
+Xilinx AXI VDMA engine, it does transfers between memory and video devices.
+It can be configured to have one channel or two channels. If configured
+as two channels, one is to transmit to the video device and another is
+to receive from the video device.
+
+Required properties:
+- compatible: Should be "xlnx,axi-vdma-1.00.a"
+- #dma-cells: Should be <1>, see "dmas" property below
+- reg: Should contain VDMA registers location and length.
+- xlnx,num-fstores: Should be the number of framebuffers as configured in h/w.
+- dma-channel child node: Should have at least one channel and can have up to
+	two channels per device. This node specifies the properties of each
+	DMA channel (see child node properties below).
+
+Optional properties:
+- xlnx,include-sg: Tells configured for Scatter-mode in
+	the hardware.
+- xlnx,flush-fsync: Tells which channel to Flush on Frame sync.
+	It takes following values:
+	{1}, flush both channels
+	{2}, flush mm2s channel
+	{3}, flush s2mm channel
+
+Required child node properties:
+- compatible: It should be either "xlnx,axi-vdma-mm2s-channel" or
+	"xlnx,axi-vdma-s2mm-channel".
+- interrupts: Should contain per channel VDMA interrupts.
+- xlnx,data-width: Should contain the stream data width, take values
+	{32,64...1024}.
+
+Optional child node properties:
+- xlnx,include-dre: Tells hardware is configured for Data
+	Realignment Engine.
+- xlnx,genlock-mode: Tells Genlock synchronization is
+	enabled/disabled in hardware.
+
+Example:
+++++++++
+
+axi_vdma_0: axivdma@40030000 {
+	compatible = "xlnx,axi-vdma-1.00.a";
+	#dma_cells = <1>;
+	reg = < 0x40030000 0x10000 >;
+	xlnx,num-fstores = <0x8>;
+	xlnx,flush-fsync = <0x1>;
+	dma-channel@40030000 {
+		compatible = "xlnx,axi-vdma-mm2s-channel";
+		interrupts = < 0 54 4 >;
+		xlnx,datawidth = <0x40>;
+	} ;
+	dma-channel@40030030 {
+		compatible = "xlnx,axi-vdma-s2mm-channel";
+		interrupts = < 0 53 4 >;
+		xlnx,datawidth = <0x40>;
+	} ;
+} ;
+
+
+* DMA client
+
+Required properties:
+- dmas: a list of <[Video DMA device phandle] [Channel ID]> pairs,
+	where Channel ID is '0' for write/tx and '1' for read/rx
+	channel.
+- dma-names: a list of DMA channel names, one per "dmas" entry
+
+Example:
+++++++++
+
+vdmatest_0: vdmatest@0 {
+	compatible ="xlnx,axi-vdma-test-1.00.a";
+	dmas = <&axi_vdma_0 0
+		&axi_vdma_0 1>;
+	dma-names = "vdma0", "vdma1";
+} ;

drivers/dma/Kconfig

@@ -361,6 +361,20 @@ config FSL_EDMA
 	  multiplexing capability for DMA request sources(slot).
 	  This module can be found on Freescale Vybrid and LS-1 SoCs.
 
+config XILINX_VDMA
+	tristate "Xilinx AXI VDMA Engine"
+	depends on (ARCH_ZYNQ || MICROBLAZE)
+	select DMA_ENGINE
+	help
+	  Enable support for Xilinx AXI VDMA Soft IP.
+
+	  This engine provides high-bandwidth direct memory access
+	  between memory and AXI4-Stream video type target
+	  peripherals including peripherals which support AXI4-
+	  Stream Video Protocol.  It has two stream interfaces/
+	  channels, Memory Mapped to Stream (MM2S) and Stream to
+	  Memory Mapped (S2MM) for the data transfers.
+
 config DMA_ENGINE
 	bool
 

drivers/dma/Makefile

@@ -46,3 +46,4 @@ obj-$(CONFIG_K3_DMA) += k3dma.o
 obj-$(CONFIG_MOXART_DMA) += moxart-dma.o
 obj-$(CONFIG_FSL_EDMA) += fsl-edma.o
 obj-$(CONFIG_QCOM_BAM_DMA) += qcom_bam_dma.o
+obj-y += xilinx/

drivers/dma/xilinx/Makefile

@@ -0,0 +1 @@
+obj-$(CONFIG_XILINX_VDMA) += xilinx_vdma.o