Merge branch 'l2x0' of rmk tree into prima2-l2x0

Documentation/devicetree/bindings/arm/l2cc.txt

@@ -0,0 +1,44 @@
+* ARM L2 Cache Controller
+
+ARM cores often have a separate level 2 cache controller. There are various
+implementations of the L2 cache controller with compatible programming models.
+The ARM L2 cache representation in the device tree should be done as follows:
+
+Required properties:
+
+- compatible : should be one of:
+	"arm,pl310-cache"
+	"arm,l220-cache"
+	"arm,l210-cache"
+- cache-unified : Specifies the cache is a unified cache.
+- cache-level : Should be set to 2 for a level 2 cache.
+- reg : Physical base address and size of cache controller's memory mapped
+  registers.
+
+Optional properties:
+
+- arm,data-latency : Cycles of latency for Data RAM accesses. Specifies 3 cells of
+  read, write and setup latencies. Minimum valid values are 1. Controllers
+  without setup latency control should use a value of 0.
+- arm,tag-latency : Cycles of latency for Tag RAM accesses. Specifies 3 cells of
+  read, write and setup latencies. Controllers without setup latency control
+  should use 0. Controllers without separate read and write Tag RAM latency
+  values should only use the first cell.
+- arm,dirty-latency : Cycles of latency for Dirty RAMs. This is a single cell.
+- arm,filter-ranges : <start length> Starting address and length of window to
+  filter. Addresses in the filter window are directed to the M1 port. Other
+  addresses will go to the M0 port.
+- interrupts : 1 combined interrupt.
+
+Example:
+
+L2: cache-controller {
+        compatible = "arm,pl310-cache";
+        reg = <0xfff12000 0x1000>;
+        arm,data-latency = <1 1 1>;
+        arm,tag-latency = <2 2 2>;
+        arm,filter-latency = <0x80000000 0x8000000>;
+        cache-unified;
+        cache-level = <2>;
+	interrupts = <45>;
+};

Documentation/hwmon/max16065

@@ -62,6 +62,13 @@ can be safely used to identify the chip. You will have to instantiate
 the devices explicitly. Please see Documentation/i2c/instantiating-devices for
 details.
 
+WARNING: Do not access chip registers using the i2cdump command, and do not use
+any of the i2ctools commands on a command register (0xa5 to 0xac). The chips
+supported by this driver interpret any access to a command register (including
+read commands) as request to execute the command in question. This may result in
+power loss, board resets, and/or Flash corruption. Worst case, your board may
+turn into a brick.
+
 
 Sysfs entries
 -------------

arch/arm/include/asm/hardware/cache-l2x0.h

@@ -45,8 +45,15 @@
 #define L2X0_CLEAN_INV_LINE_PA		0x7F0
 #define L2X0_CLEAN_INV_LINE_IDX		0x7F8
 #define L2X0_CLEAN_INV_WAY		0x7FC
-#define L2X0_LOCKDOWN_WAY_D		0x900
-#define L2X0_LOCKDOWN_WAY_I		0x904
+/*
+ * The lockdown registers repeat 8 times for L310, the L210 has only one
+ * D and one I lockdown register at 0x0900 and 0x0904.
+ */
+#define L2X0_LOCKDOWN_WAY_D_BASE	0x900
+#define L2X0_LOCKDOWN_WAY_I_BASE	0x904
+#define L2X0_LOCKDOWN_STRIDE		0x08
+#define L2X0_ADDR_FILTER_START		0xC00
+#define L2X0_ADDR_FILTER_END		0xC04
 #define L2X0_TEST_OPERATION		0xF00
 #define L2X0_LINE_DATA			0xF10
 #define L2X0_LINE_TAG			0xF30
@@ -60,8 +67,23 @@
 #define L2X0_CACHE_ID_PART_MASK		(0xf << 6)
 #define L2X0_CACHE_ID_PART_L210		(1 << 6)
 #define L2X0_CACHE_ID_PART_L310		(3 << 6)
+#define L2X0_CACHE_ID_RTL_MASK          0x3f
+#define L2X0_CACHE_ID_RTL_R0P0          0x0
+#define L2X0_CACHE_ID_RTL_R1P0          0x2
+#define L2X0_CACHE_ID_RTL_R2P0          0x4
+#define L2X0_CACHE_ID_RTL_R3P0          0x5
+#define L2X0_CACHE_ID_RTL_R3P1          0x6
+#define L2X0_CACHE_ID_RTL_R3P2          0x8
 
 #define L2X0_AUX_CTRL_MASK			0xc0000fff
+#define L2X0_AUX_CTRL_DATA_RD_LATENCY_SHIFT	0
+#define L2X0_AUX_CTRL_DATA_RD_LATENCY_MASK	0x7
+#define L2X0_AUX_CTRL_DATA_WR_LATENCY_SHIFT	3
+#define L2X0_AUX_CTRL_DATA_WR_LATENCY_MASK	(0x7 << 3)
+#define L2X0_AUX_CTRL_TAG_LATENCY_SHIFT		6
+#define L2X0_AUX_CTRL_TAG_LATENCY_MASK		(0x7 << 6)
+#define L2X0_AUX_CTRL_DIRTY_LATENCY_SHIFT	9
+#define L2X0_AUX_CTRL_DIRTY_LATENCY_MASK	(0x7 << 9)
 #define L2X0_AUX_CTRL_ASSOCIATIVITY_SHIFT	16
 #define L2X0_AUX_CTRL_WAY_SIZE_SHIFT		17
 #define L2X0_AUX_CTRL_WAY_SIZE_MASK		(0x7 << 17)
@@ -72,8 +94,33 @@
 #define L2X0_AUX_CTRL_INSTR_PREFETCH_SHIFT	29
 #define L2X0_AUX_CTRL_EARLY_BRESP_SHIFT		30
 
+#define L2X0_LATENCY_CTRL_SETUP_SHIFT	0
+#define L2X0_LATENCY_CTRL_RD_SHIFT	4
+#define L2X0_LATENCY_CTRL_WR_SHIFT	8
+
+#define L2X0_ADDR_FILTER_EN		1
+
 #ifndef __ASSEMBLY__
 extern void __init l2x0_init(void __iomem *base, __u32 aux_val, __u32 aux_mask);
+extern int l2x0_of_init(__u32 aux_val, __u32 aux_mask);
+
+struct l2x0_regs {
+	unsigned long phy_base;
+	unsigned long aux_ctrl;
+	/*
+	 * Whether the following registers need to be saved/restored
+	 * depends on platform
+	 */
+	unsigned long tag_latency;
+	unsigned long data_latency;
+	unsigned long filter_start;
+	unsigned long filter_end;
+	unsigned long prefetch_ctrl;
+	unsigned long pwr_ctrl;
+};
+
+extern struct l2x0_regs l2x0_saved_regs;
+
 #endif
 
 #endif

arch/arm/include/asm/outercache.h

@@ -34,6 +34,7 @@ struct outer_cache_fns {
 	void (*sync)(void);
 #endif
 	void (*set_debug)(unsigned long);
+	void (*resume)(void);
 };
 
 #ifdef CONFIG_OUTER_CACHE
@@ -74,6 +75,12 @@ static inline void outer_disable(void)
 		outer_cache.disable();
 }
 
+static inline void outer_resume(void)
+{
+	if (outer_cache.resume)
+		outer_cache.resume();
+}
+
 #else
 
 static inline void outer_inv_range(phys_addr_t start, phys_addr_t end)

arch/arm/kernel/asm-offsets.c

@@ -20,6 +20,7 @@
 #include <asm/thread_info.h>
 #include <asm/memory.h>
 #include <asm/procinfo.h>
+#include <asm/hardware/cache-l2x0.h>
 #include <linux/kbuild.h>
 
 /*
@@ -92,6 +93,17 @@ int main(void)
   DEFINE(S_OLD_R0,		offsetof(struct pt_regs, ARM_ORIG_r0));
   DEFINE(S_FRAME_SIZE,		sizeof(struct pt_regs));
   BLANK();
+#ifdef CONFIG_CACHE_L2X0
+  DEFINE(L2X0_R_PHY_BASE,	offsetof(struct l2x0_regs, phy_base));
+  DEFINE(L2X0_R_AUX_CTRL,	offsetof(struct l2x0_regs, aux_ctrl));
+  DEFINE(L2X0_R_TAG_LATENCY,	offsetof(struct l2x0_regs, tag_latency));
+  DEFINE(L2X0_R_DATA_LATENCY,	offsetof(struct l2x0_regs, data_latency));
+  DEFINE(L2X0_R_FILTER_START,	offsetof(struct l2x0_regs, filter_start));
+  DEFINE(L2X0_R_FILTER_END,	offsetof(struct l2x0_regs, filter_end));
+  DEFINE(L2X0_R_PREFETCH_CTRL,	offsetof(struct l2x0_regs, prefetch_ctrl));
+  DEFINE(L2X0_R_PWR_CTRL,	offsetof(struct l2x0_regs, pwr_ctrl));
+  BLANK();
+#endif
 #ifdef CONFIG_CPU_HAS_ASID
   DEFINE(MM_CONTEXT_ID,		offsetof(struct mm_struct, context.id));
   BLANK();

arch/arm/mach-integrator/integrator_ap.c

@@ -337,15 +337,15 @@ static unsigned long timer_reload;
 static void integrator_clocksource_init(u32 khz)
 {
 	void __iomem *base = (void __iomem *)TIMER2_VA_BASE;
-	u32 ctrl = TIMER_CTRL_ENABLE;
+	u32 ctrl = TIMER_CTRL_ENABLE | TIMER_CTRL_PERIODIC;
 
 	if (khz >= 1500) {
 		khz /= 16;
-		ctrl = TIMER_CTRL_DIV16;
+		ctrl |= TIMER_CTRL_DIV16;
 	}
 
-	writel(ctrl, base + TIMER_CTRL);
 	writel(0xffff, base + TIMER_LOAD);
+	writel(ctrl, base + TIMER_CTRL);
 
 	clocksource_mmio_init(base + TIMER_VALUE, "timer2",
 		khz * 1000, 200, 16, clocksource_mmio_readl_down);

arch/arm/mm/abort-macro.S

@@ -17,7 +17,7 @@
 	cmp	\tmp, # 0x5600			@ Is it ldrsb?
 	orreq	\tmp, \tmp, #1 << 11		@ Set L-bit if yes
 	tst	\tmp, #1 << 11			@ L = 0 -> write
-	orreq	\psr, \psr, #1 << 11		@ yes.
+	orreq	\fsr, \fsr, #1 << 11		@ yes.
 	b	do_DataAbort
 not_thumb:
 	.endm