---

yaml
---
r: 291553
b: refs/heads/master
c: 01a2829
h: refs/heads/master
i:
  291551: 729656d
v: v3

[refs]

@@ -1,2 +1,2 @@
 ---
-refs/heads/master: 377526578f2c343ea281a918b18ece1fca65005c
+refs/heads/master: 01a282980937f9ca55a3cb06b9c6ff1cc49ea396

trunk/Documentation/ABI/testing/sysfs-class-net-mesh

@@ -65,6 +65,13 @@ Description:
 		Defines the penalty which will be applied to an
 		originator message's tq-field on every hop.
 
+What:		/sys/class/net/<mesh_iface>/mesh/routing_algo
+Date:		Dec 2011
+Contact:	Marek Lindner <lindner_marek@yahoo.de>
+Description:
+		Defines the routing procotol this mesh instance
+		uses to find the optimal paths through the mesh.
+
 What:           /sys/class/net/<mesh_iface>/mesh/vis_mode
 Date:           May 2010
 Contact:        Marek Lindner <lindner_marek@yahoo.de>

trunk/Documentation/DocBook/device-drivers.tmpl

@@ -102,9 +102,12 @@ X!Iinclude/linux/kobject.h
 !Iinclude/linux/device.h
      </sect1>
      <sect1><title>Device Drivers Base</title>
+!Idrivers/base/init.c
 !Edrivers/base/driver.c
 !Edrivers/base/core.c
+!Edrivers/base/syscore.c
 !Edrivers/base/class.c
+!Idrivers/base/node.c
 !Edrivers/base/firmware_class.c
 !Edrivers/base/transport_class.c
 <!-- Cannot be included, because
@@ -113,13 +116,18 @@ X!Iinclude/linux/kobject.h
      exceed allowed 44 characters maximum
 X!Edrivers/base/attribute_container.c
 -->
-!Edrivers/base/sys.c
+!Edrivers/base/dd.c
 <!--
 X!Edrivers/base/interface.c
 -->
 !Iinclude/linux/platform_device.h
 !Edrivers/base/platform.c
 !Edrivers/base/bus.c
+     </sect1>
+     <sect1><title>Device Drivers DMA Management</title>
+!Edrivers/base/dma-buf.c
+!Edrivers/base/dma-coherent.c
+!Edrivers/base/dma-mapping.c
      </sect1>
      <sect1><title>Device Drivers Power Management</title>
 !Edrivers/base/power/main.c
@@ -219,7 +227,7 @@ X!Isound/sound_firmware.c
   <chapter id="uart16x50">
      <title>16x50 UART Driver</title>
 !Edrivers/tty/serial/serial_core.c
-!Edrivers/tty/serial/8250.c
+!Edrivers/tty/serial/8250/8250.c
   </chapter>
 
   <chapter id="fbdev">

trunk/Documentation/devicetree/bindings/gpio/led.txt

@@ -7,9 +7,9 @@ Each LED is represented as a sub-node of the gpio-leds device.  Each
 node's name represents the name of the corresponding LED.
 
 LED sub-node properties:
-- gpios :  Should specify the LED's GPIO, see "Specifying GPIO information
-  for devices" in Documentation/devicetree/booting-without-of.txt.  Active
-  low LEDs should be indicated using flags in the GPIO specifier.
+- gpios :  Should specify the LED's GPIO, see "gpios property" in
+  Documentation/devicetree/gpio.txt.  Active low LEDs should be
+  indicated using flags in the GPIO specifier.
 - label :  (optional) The label for this LED.  If omitted, the label is
   taken from the node name (excluding the unit address).
 - linux,default-trigger :  (optional) This parameter, if present, is a

trunk/Documentation/devicetree/bindings/vendor-prefixes.txt

@@ -30,6 +30,7 @@ national	National Semiconductor
 nintendo	Nintendo
 nvidia	NVIDIA
 nxp	NXP Semiconductors
+picochip	Picochip Ltd
 powervr	Imagination Technologies
 qcom	Qualcomm, Inc.
 ramtron	Ramtron International

trunk/Documentation/driver-model/devres.txt

@@ -233,6 +233,10 @@ certainly invest a bit more effort into libata core layer).
   6. List of managed interfaces
   -----------------------------
 
+MEM
+  devm_kzalloc()
+  devm_kfree()
+
 IO region
   devm_request_region()
   devm_request_mem_region()

trunk/Documentation/feature-removal-schedule.txt

@@ -510,3 +510,17 @@ Why:	The pci_scan_bus_parented() interface creates a new root bus.  The
 	convert to using pci_scan_root_bus() so they can supply a list of
 	bus resources when the bus is created.
 Who:	Bjorn Helgaas <bhelgaas@google.com>
+
+----------------------------
+
+What:	The CAP9 SoC family will be removed
+When:	3.4
+Files:	arch/arm/mach-at91/at91cap9.c
+	arch/arm/mach-at91/at91cap9_devices.c
+	arch/arm/mach-at91/include/mach/at91cap9.h
+	arch/arm/mach-at91/include/mach/at91cap9_matrix.h
+	arch/arm/mach-at91/include/mach/at91cap9_ddrsdr.h
+	arch/arm/mach-at91/board-cap9adk.c
+Why:	The code is not actively maintained and platforms are now hard to find.
+Who:	Nicolas Ferre <nicolas.ferre@atmel.com>
+	Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

trunk/Documentation/hwmon/jc42

@@ -7,21 +7,29 @@ Supported chips:
     Addresses scanned: I2C 0x18 - 0x1f
     Datasheets:
 	http://www.analog.com/static/imported-files/data_sheets/ADT7408.pdf
-  * IDT TSE2002B3, TS3000B3
-    Prefix: 'tse2002b3', 'ts3000b3'
+  * Atmel AT30TS00
+    Prefix: 'at30ts00'
     Addresses scanned: I2C 0x18 - 0x1f
     Datasheets:
-	http://www.idt.com/products/getdoc.cfm?docid=18715691
-	http://www.idt.com/products/getdoc.cfm?docid=18715692
+	http://www.atmel.com/Images/doc8585.pdf
+  * IDT TSE2002B3, TSE2002GB2, TS3000B3, TS3000GB2
+    Prefix: 'tse2002', 'ts3000'
+    Addresses scanned: I2C 0x18 - 0x1f
+    Datasheets:
+	http://www.idt.com/sites/default/files/documents/IDT_TSE2002B3C_DST_20100512_120303152056.pdf
+	http://www.idt.com/sites/default/files/documents/IDT_TSE2002GB2A1_DST_20111107_120303145914.pdf
+	http://www.idt.com/sites/default/files/documents/IDT_TS3000B3A_DST_20101129_120303152013.pdf
+	http://www.idt.com/sites/default/files/documents/IDT_TS3000GB2A1_DST_20111104_120303151012.pdf
   * Maxim MAX6604
     Prefix: 'max6604'
     Addresses scanned: I2C 0x18 - 0x1f
     Datasheets:
 	http://datasheets.maxim-ic.com/en/ds/MAX6604.pdf
-  * Microchip MCP9805, MCP98242, MCP98243, MCP9843
-    Prefixes: 'mcp9805', 'mcp98242', 'mcp98243', 'mcp9843'
+  * Microchip MCP9804, MCP9805, MCP98242, MCP98243, MCP9843
+    Prefixes: 'mcp9804', 'mcp9805', 'mcp98242', 'mcp98243', 'mcp9843'
     Addresses scanned: I2C 0x18 - 0x1f
     Datasheets:
+	http://ww1.microchip.com/downloads/en/DeviceDoc/22203C.pdf
 	http://ww1.microchip.com/downloads/en/DeviceDoc/21977b.pdf
 	http://ww1.microchip.com/downloads/en/DeviceDoc/21996a.pdf
 	http://ww1.microchip.com/downloads/en/DeviceDoc/22153c.pdf
@@ -48,6 +56,12 @@ Supported chips:
     Datasheets:
 	http://www.st.com/stonline/products/literature/ds/13447/stts424.pdf
 	http://www.st.com/stonline/products/literature/ds/13448/stts424e02.pdf
+  * ST Microelectronics STTS2002, STTS3000
+    Prefix: 'stts2002', 'stts3000'
+    Addresses scanned: I2C 0x18 - 0x1f
+    Datasheets:
+	http://www.st.com/internet/com/TECHNICAL_RESOURCES/TECHNICAL_LITERATURE/DATASHEET/CD00225278.pdf
+	http://www.st.com/internet/com/TECHNICAL_RESOURCES/TECHNICAL_LITERATURE/DATA_BRIEF/CD00270920.pdf
   * JEDEC JC 42.4 compliant temperature sensor chips
     Prefix: 'jc42'
     Addresses scanned: I2C 0x18 - 0x1f

trunk/Documentation/input/alps.txt

@@ -13,7 +13,8 @@ Detection
 
 All ALPS touchpads should respond to the "E6 report" command sequence:
 E8-E6-E6-E6-E9. An ALPS touchpad should respond with either 00-00-0A or
-00-00-64.
+00-00-64 if no buttons are pressed. The bits 0-2 of the first byte will be 1s
+if some buttons are pressed.
 
 If the E6 report is successful, the touchpad model is identified using the "E7
 report" sequence: E8-E7-E7-E7-E9. The response is the model signature and is

trunk/Documentation/input/event-codes.txt

@@ -17,11 +17,11 @@ reports supported by a device are also provided by sysfs in
 class/input/event*/device/capabilities/, and the properties of a device are
 provided in class/input/event*/device/properties.
 
-Types:
-==========
-Types are groupings of codes under a logical input construct. Each type has a
-set of applicable codes to be used in generating events. See the Codes section
-for details on valid codes for each type.
+Event types:
+===========
+Event types are groupings of codes under a logical input construct. Each
+type has a set of applicable codes to be used in generating events. See the
+Codes section for details on valid codes for each type.
 
 * EV_SYN:
   - Used as markers to separate events. Events may be separated in time or in
@@ -63,9 +63,9 @@ for details on valid codes for each type.
 * EV_FF_STATUS:
   - Used to receive force feedback device status.
 
-Codes:
-==========
-Codes define the precise type of event.
+Event codes:
+===========
+Event codes define the precise type of event.
 
 EV_SYN:
 ----------
@@ -220,6 +220,56 @@ EV_PWR:
 EV_PWR events are a special type of event used specifically for power
 mangement. Its usage is not well defined. To be addressed later.
 
+Device properties:
+=================
+Normally, userspace sets up an input device based on the data it emits,
+i.e., the event types. In the case of two devices emitting the same event
+types, additional information can be provided in the form of device
+properties.
+
+INPUT_PROP_DIRECT + INPUT_PROP_POINTER:
+--------------------------------------
+The INPUT_PROP_DIRECT property indicates that device coordinates should be
+directly mapped to screen coordinates (not taking into account trivial
+transformations, such as scaling, flipping and rotating). Non-direct input
+devices require non-trivial transformation, such as absolute to relative
+transformation for touchpads. Typical direct input devices: touchscreens,
+drawing tablets; non-direct devices: touchpads, mice.
+
+The INPUT_PROP_POINTER property indicates that the device is not transposed
+on the screen and thus requires use of an on-screen pointer to trace user's
+movements.  Typical pointer devices: touchpads, tablets, mice; non-pointer
+device: touchscreen.
+
+If neither INPUT_PROP_DIRECT or INPUT_PROP_POINTER are set, the property is
+considered undefined and the device type should be deduced in the
+traditional way, using emitted event types.
+
+INPUT_PROP_BUTTONPAD:
+--------------------
+For touchpads where the button is placed beneath the surface, such that
+pressing down on the pad causes a button click, this property should be
+set. Common in clickpad notebooks and macbooks from 2009 and onwards.
+
+Originally, the buttonpad property was coded into the bcm5974 driver
+version field under the name integrated button. For backwards
+compatibility, both methods need to be checked in userspace.
+
+INPUT_PROP_SEMI_MT:
+------------------
+Some touchpads, most common between 2008 and 2011, can detect the presence
+of multiple contacts without resolving the individual positions; only the
+number of contacts and a rectangular shape is known. For such
+touchpads, the semi-mt property should be set.
+
+Depending on the device, the rectangle may enclose all touches, like a
+bounding box, or just some of them, for instance the two most recent
+touches. The diversity makes the rectangle of limited use, but some
+gestures can normally be extracted from it.
+
+If INPUT_PROP_SEMI_MT is not set, the device is assumed to be a true MT
+device.
+
 Guidelines:
 ==========
 The guidelines below ensure proper single-touch and multi-finger functionality.
@@ -240,6 +290,8 @@ used to report when a touch is active on the screen.
 BTN_{MOUSE,LEFT,MIDDLE,RIGHT} must not be reported as the result of touch
 contact. BTN_TOOL_<name> events should be reported where possible.
 
+For new hardware, INPUT_PROP_DIRECT should be set.
+
 Trackpads:
 ----------
 Legacy trackpads that only provide relative position information must report
@@ -250,6 +302,8 @@ location of the touch. BTN_TOUCH should be used to report when a touch is active
 on the trackpad. Where multi-finger support is available, BTN_TOOL_<name> should
 be used to report the number of touches active on the trackpad.
 
+For new hardware, INPUT_PROP_POINTER should be set.
+
 Tablets:
 ----------
 BTN_TOOL_<name> events must be reported when a stylus or other tool is active on
@@ -260,3 +314,5 @@ button may be used for buttons on the tablet except BTN_{MOUSE,LEFT}.
 BTN_{0,1,2,etc} are good generic codes for unlabeled buttons. Do not use
 meaningful buttons, like BTN_FORWARD, unless the button is labeled for that
 purpose on the device.
+
+For new hardware, both INPUT_PROP_DIRECT and INPUT_PROP_POINTER should be set.

trunk/Documentation/ioctl/ioctl-number.txt

@@ -255,7 +255,7 @@ Code  Seq#(hex)	Include File		Comments
 		linux/ixjuser.h		<http://web.archive.org/web/*/http://www.quicknet.net>
 'r'	00-1F	linux/msdos_fs.h and fs/fat/dir.c
 's'	all	linux/cdk.h
-'t'	00-7F	linux/if_ppp.h
+'t'	00-7F	linux/ppp-ioctl.h
 't'	80-8F	linux/isdn_ppp.h
 't'	90	linux/toshiba.h
 'u'	00-1F	linux/smb_fs.h		gone

trunk/Documentation/kernel-parameters.txt

@@ -2211,6 +2211,12 @@ bytes respectively. Such letter suffixes can also be entirely omitted.
 
 			default: off.
 
+	printk.always_kmsg_dump=
+			Trigger kmsg_dump for cases other than kernel oops or
+			panics
+			Format: <bool>  (1/Y/y=enable, 0/N/n=disable)
+			default: disabled
+
 	printk.time=	Show timing data prefixed to each printk message line
 			Format: <bool>  (1/Y/y=enable, 0/N/n=disable)
 

trunk/Documentation/magic-number.txt

@@ -89,7 +89,7 @@ TTY_DRIVER_MAGIC      0x5402      tty_driver        include/linux/tty_driver.h
 MGSLPC_MAGIC          0x5402      mgslpc_info       drivers/char/pcmcia/synclink_cs.c
 TTY_LDISC_MAGIC       0x5403      tty_ldisc         include/linux/tty_ldisc.h
 USB_SERIAL_MAGIC      0x6702      usb_serial        drivers/usb/serial/usb-serial.h
-FULL_DUPLEX_MAGIC     0x6969                        drivers/net/tulip/de2104x.c
+FULL_DUPLEX_MAGIC     0x6969                        drivers/net/ethernet/dec/tulip/de2104x.c
 USB_BLUETOOTH_MAGIC   0x6d02      usb_bluetooth     drivers/usb/class/bluetty.c
 RFCOMM_TTY_MAGIC      0x6d02                        net/bluetooth/rfcomm/tty.c
 USB_SERIAL_PORT_MAGIC 0x7301      usb_serial_port   drivers/usb/serial/usb-serial.h