---

yaml
---
r: 342406
b: refs/heads/master
c: 84d2e38
h: refs/heads/master
v: v3

[refs]

@@ -1,2 +1,2 @@
 ---
-refs/heads/master: 46e8a79eb5449204f4b20d71c38c96b981b04e96
+refs/heads/master: 84d2e38e935620004245f0e22113cf8389834635

trunk/Documentation/devicetree/bindings/clock/zynq-7000.txt

@@ -0,0 +1,55 @@
+Device Tree Clock bindings for the Zynq 7000 EPP
+
+The Zynq EPP has several different clk providers, each with there own bindings.
+The purpose of this document is to document their usage.
+
+See clock_bindings.txt for more information on the generic clock bindings.
+See Chapter 25 of Zynq TRM for more information about Zynq clocks.
+
+== PLLs ==
+
+Used to describe the ARM_PLL, DDR_PLL, and IO_PLL.
+
+Required properties:
+- #clock-cells : shall be 0 (only one clock is output from this node)
+- compatible : "xlnx,zynq-pll"
+- reg : pair of u32 values, which are the address offsets within the SLCR
+        of the relevant PLL_CTRL register and PLL_CFG register respectively
+- clocks : phandle for parent clock.  should be the phandle for ps_clk
+
+Optional properties:
+- clock-output-names : name of the output clock
+
+Example:
+	armpll: armpll {
+		#clock-cells = <0>;
+		compatible = "xlnx,zynq-pll";
+		clocks = <&ps_clk>;
+		reg = <0x100 0x110>;
+		clock-output-names = "armpll";
+	};
+
+== Peripheral clocks ==
+
+Describes clock node for the SDIO, SMC, SPI, QSPI, and UART clocks.
+
+Required properties:
+- #clock-cells : shall be 1
+- compatible : "xlnx,zynq-periph-clock"
+- reg : a single u32 value, describing the offset within the SLCR where
+        the CLK_CTRL register is found for this peripheral
+- clocks : phandle for parent clocks.  should hold phandles for
+           the IO_PLL, ARM_PLL, and DDR_PLL in order
+- clock-output-names : names of the output clock(s).  For peripherals that have
+                       two output clocks (for example, the UART), two clocks
+                       should be listed.
+
+Example:
+	uart_clk: uart_clk {
+		#clock-cells = <1>;
+		compatible = "xlnx,zynq-periph-clock";
+		clocks = <&iopll &armpll &ddrpll>;
+		reg = <0x154>;
+		clock-output-names = "uart0_ref_clk",
+				     "uart1_ref_clk";
+	};

trunk/Documentation/devicetree/bindings/vendor-prefixes.txt

@@ -51,5 +51,4 @@ ti	Texas Instruments
 via	VIA Technologies, Inc.
 wlf	Wolfson Microelectronics
 wm	Wondermedia Technologies, Inc.
-winbond Winbond Electronics corp.
 xlnx	Xilinx

trunk/arch/arm/Kconfig

@@ -644,7 +644,6 @@ config ARCH_TEGRA
 	select HAVE_CLK
 	select HAVE_SMP
 	select MIGHT_HAVE_CACHE_L2X0
-	select SPARSE_IRQ
 	select USE_OF
 	help
 	  This enables support for NVIDIA Tegra based systems (Tegra APX,
@@ -886,7 +885,6 @@ config ARCH_U8500
 	select GENERIC_CLOCKEVENTS
 	select HAVE_SMP
 	select MIGHT_HAVE_CACHE_L2X0
-	select SPARSE_IRQ
 	help
 	  Support for ST-Ericsson's Ux500 architecture
 
@@ -901,7 +899,6 @@ config ARCH_NOMADIK
 	select MIGHT_HAVE_CACHE_L2X0
 	select PINCTRL
 	select PINCTRL_STN8815
-	select SPARSE_IRQ
 	help
 	  Support for the Nomadik platform by ST-Ericsson
 
@@ -944,7 +941,7 @@ config ARCH_OMAP
 	help
 	  Support for TI's OMAP platform (OMAP1/2/3/4).
 
-config ARCH_VT8500_SINGLE
+config ARCH_VT8500
 	bool "VIA/WonderMedia 85xx"
 	select ARCH_HAS_CPUFREQ
 	select ARCH_REQUIRE_GPIOLIB
@@ -954,8 +951,6 @@ config ARCH_VT8500_SINGLE
 	select GENERIC_CLOCKEVENTS
 	select GENERIC_GPIO
 	select HAVE_CLK
-	select MULTI_IRQ_HANDLER
-	select SPARSE_IRQ
 	select USE_OF
 	help
 	  Support for VIA/WonderMedia VT8500/WM85xx System-on-Chip.
@@ -964,7 +959,7 @@ config ARCH_ZYNQ
 	bool "Xilinx Zynq ARM Cortex A9 Platform"
 	select ARM_AMBA
 	select ARM_GIC
-	select CLKDEV_LOOKUP
+	select COMMON_CLK
 	select CPU_V7
 	select GENERIC_CLOCKEVENTS
 	select ICST
@@ -1070,6 +1065,7 @@ source "arch/arm/mach-mxs/Kconfig"
 source "arch/arm/mach-netx/Kconfig"
 
 source "arch/arm/mach-nomadik/Kconfig"
+source "arch/arm/plat-nomadik/Kconfig"
 
 source "arch/arm/plat-omap/Kconfig"
 
@@ -1130,8 +1126,6 @@ source "arch/arm/mach-versatile/Kconfig"
 source "arch/arm/mach-vexpress/Kconfig"
 source "arch/arm/plat-versatile/Kconfig"
 
-source "arch/arm/mach-vt8500/Kconfig"
-
 source "arch/arm/mach-w90x900/Kconfig"
 
 # Definitions to make life easier

trunk/arch/arm/Kconfig.debug

@@ -132,6 +132,23 @@ choice
 		  their output to UART1 serial port on DaVinci TNETV107X
 		  devices.
 
+	config DEBUG_ZYNQ_UART0
+		bool "Kernel low-level debugging on Xilinx Zynq using UART0"
+		depends on ARCH_ZYNQ
+		help
+		  Say Y here if you want the debug print routines to direct
+		  their output to UART0 on the Zynq platform.
+
+	config DEBUG_ZYNQ_UART1
+		bool "Kernel low-level debugging on Xilinx Zynq using UART1"
+		depends on ARCH_ZYNQ
+		help
+		  Say Y here if you want the debug print routines to direct
+		  their output to UART1 on the Zynq platform.
+
+		  If you have a ZC702 board and want early boot messages to
+		  appear on the USB serial adaptor, select this option.
+
 	config DEBUG_DC21285_PORT
 		bool "Kernel low-level debugging messages via footbridge serial port"
 		depends on FOOTBRIDGE
@@ -345,13 +362,6 @@ choice
 		  Say Y here if you want kernel low-level debugging support
 		  on SOCFPGA based platforms.
 
-	config DEBUG_TEGRA_UART
-		depends on ARCH_TEGRA
-		bool "Use Tegra UART for low-level debug"
-		help
-		  Say Y here if you want kernel low-level debugging support
-		  on Tegra based platforms.
-
 	config DEBUG_VEXPRESS_UART0_DETECT
 		bool "Autodetect UART0 on Versatile Express Cortex-A core tiles"
 		depends on ARCH_VEXPRESS && CPU_CP15_MMU
@@ -416,36 +426,6 @@ choice
 
 endchoice
 
-choice
-	prompt "Low-level debug console UART"
-	depends on DEBUG_LL && DEBUG_TEGRA_UART
-
-	config TEGRA_DEBUG_UART_AUTO_ODMDATA
-	bool "Via ODMDATA"
-	help
-	  Automatically determines which UART to use for low-level debug based
-	  on the ODMDATA value. This value is part of the BCT, and is written
-	  to the boot memory device using nvflash, or other flashing tool.
-	  When bits 19:18 are 3, then bits 17:15 indicate which UART to use;
-	  0/1/2/3/4 are UART A/B/C/D/E.
-
-	config TEGRA_DEBUG_UARTA
-		bool "UART A"
-
-	config TEGRA_DEBUG_UARTB
-		bool "UART B"
-
-	config TEGRA_DEBUG_UARTC
-		bool "UART C"
-
-	config TEGRA_DEBUG_UARTD
-		bool "UART D"
-
-	config TEGRA_DEBUG_UARTE
-		bool "UART E"
-
-endchoice
-
 config DEBUG_LL_INCLUDE
 	string
 	default "debug/icedcc.S" if DEBUG_ICEDCC
@@ -455,7 +435,6 @@ config DEBUG_LL_INCLUDE
 	default "debug/socfpga.S" if DEBUG_SOCFPGA_UART
 	default "debug/vexpress.S" if DEBUG_VEXPRESS_UART0_DETECT || \
 		DEBUG_VEXPRESS_UART0_CA9 || DEBUG_VEXPRESS_UART0_RS1
-	default "debug/tegra.S" if DEBUG_TEGRA_UART
 	default "mach/debug-macro.S"
 
 config EARLY_PRINTK

trunk/arch/arm/Makefile

@@ -199,8 +199,8 @@ machine-$(CONFIG_ARCH_ZYNQ)		+= zynq
 plat-$(CONFIG_ARCH_MXC)		+= mxc
 plat-$(CONFIG_ARCH_OMAP)	+= omap
 plat-$(CONFIG_ARCH_S3C64XX)	+= samsung
-plat-$(CONFIG_ARCH_ZYNQ)	+= versatile
 plat-$(CONFIG_PLAT_IOP)		+= iop
+plat-$(CONFIG_PLAT_NOMADIK)	+= nomadik
 plat-$(CONFIG_PLAT_ORION)	+= orion
 plat-$(CONFIG_PLAT_PXA)		+= pxa
 plat-$(CONFIG_PLAT_S3C24XX)	+= s3c24xx samsung

trunk/arch/arm/boot/dts/Makefile

@@ -103,5 +103,6 @@ dtb-$(CONFIG_ARCH_VEXPRESS) += vexpress-v2p-ca5s.dtb \
 dtb-$(CONFIG_ARCH_VT8500) += vt8500-bv07.dtb \
 	wm8505-ref.dtb \
 	wm8650-mid.dtb
+dtb-$(CONFIG_ARCH_ZYNQ) += zynq-zc702.dtb
 
 endif