Merge remote-tracking branches 'regulator/topic/fixed', 'regulator/to…

…pic/id-const', 'regulator/topic/ltc3589', 'regulator/topic/max8649' and 'regulator/topic/of' into regulator-next

Documentation/devicetree/bindings/regulator/ltc3589.txt

@@ -0,0 +1,99 @@
+Linear Technology LTC3589, LTC3589-1, and LTC3589-2 8-output regulators
+
+Required properties:
+- compatible: "lltc,ltc3589", "lltc,ltc3589-1" or "lltc,ltc3589-2"
+- reg: I2C slave address
+
+Required child node:
+- regulators: Contains eight regulator child nodes sw1, sw2, sw3, bb-out,
+  ldo1, ldo2, ldo3, and ldo4, specifying the initialization data as
+  documented in Documentation/devicetree/bindings/regulator/regulator.txt.
+
+Each regulator is defined using the standard binding for regulators. The
+nodes for sw1, sw2, sw3, bb-out, ldo1, and ldo2 additionally need to specify
+the resistor values of their external feedback voltage dividers:
+
+Required properties (not on ldo3, ldo4):
+- lltc,fb-voltage-divider: An array of two integers containing the resistor
+  values R1 and R2 of the feedback voltage divider in ohms.
+
+Regulators sw1, sw2, sw3, and ldo2 can regulate the feedback reference from
+0.3625 V to 0.75 V in 12.5 mV steps. The output voltage thus ranges between
+0.3625 * (1 + R1/R2) V and 0.75 * (1 + R1/R2) V. Regulators bb-out and ldo1
+have a fixed 0.8 V reference and thus output 0.8 * (1 + R1/R2) V. The ldo3
+regulator is fixed to 1.8 V on LTC3589 and to 2.8 V on LTC3589-1,2. The ldo4
+regulator can output between 1.8 V and 3.3 V on LTC3589 and between 1.2 V
+and 3.2 V on LTC3589-1,2 in four steps. The ldo1 standby regulator can not
+be disabled and thus should have the regulator-always-on property set.
+
+Example:
+
+	ltc3589: pmic@34 {
+		compatible = "lltc,ltc3589-1";
+		reg = <0x34>;
+
+		regulators {
+			sw1_reg: sw1 {
+				regulator-min-microvolt = <591930>;
+				regulator-max-microvolt = <1224671>;
+				lltc,fb-voltage-divider = <100000 158000>;
+				regulator-ramp-delay = <7000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw2_reg: sw2 {
+				regulator-min-microvolt = <704123>;
+				regulator-max-microvolt = <1456803>;
+				lltc,fb-voltage-divider = <180000 191000>;
+				regulator-ramp-delay = <7000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw3_reg: sw3 {
+				regulator-min-microvolt = <1341250>;
+				regulator-max-microvolt = <2775000>;
+				lltc,fb-voltage-divider = <270000 100000>;
+				regulator-ramp-delay = <7000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			bb_out_reg: bb-out {
+				regulator-min-microvolt = <3387341>;
+				regulator-max-microvolt = <3387341>;
+				lltc,fb-voltage-divider = <511000 158000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo1_reg: ldo1 {
+				regulator-min-microvolt = <1306329>;
+				regulator-max-microvolt = <1306329>;
+				lltc,fb-voltage-divider = <100000 158000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo2_reg: ldo2 {
+				regulator-min-microvolt = <704123>;
+				regulator-max-microvolt = <1456806>;
+				lltc,fb-voltage-divider = <180000 191000>;
+				regulator-ramp-delay = <7000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo3_reg: ldo3 {
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				regulator-boot-on;
+			};
+
+			ldo4_reg: ldo4 {
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <3200000>;
+			};
+		};
+	};

Documentation/devicetree/bindings/vendor-prefixes.txt

@@ -73,6 +73,7 @@ lantiq	Lantiq Semiconductor
 lg	LG Corporation
 linux	Linux-specific binding
 lsi	LSI Corp. (LSI Logic)
+lltc	Linear Technology Corporation
 marvell	Marvell Technology Group Ltd.
 maxim	Maxim Integrated Products
 microchip	Microchip Technology Inc.

drivers/regulator/Kconfig

@@ -272,6 +272,14 @@ config REGULATOR_LP8788
 	help
 	  This driver supports LP8788 voltage regulator chip.
 
+config REGULATOR_LTC3589
+	tristate "LTC3589 8-output voltage regulator"
+	depends on I2C
+	select REGMAP_I2C
+	help
+	  This enables support for the LTC3589, LTC3589-1, and LTC3589-2
+	  8-output regulators controlled via I2C.
+
 config REGULATOR_MAX14577
 	tristate "Maxim 14577 regulator"
 	depends on MFD_MAX14577

drivers/regulator/Makefile

@@ -38,6 +38,7 @@ obj-$(CONFIG_REGULATOR_LP872X) += lp872x.o
 obj-$(CONFIG_REGULATOR_LP8788) += lp8788-buck.o
 obj-$(CONFIG_REGULATOR_LP8788) += lp8788-ldo.o
 obj-$(CONFIG_REGULATOR_LP8755) += lp8755.o
+obj-$(CONFIG_REGULATOR_LTC3589) += ltc3589.o
 obj-$(CONFIG_REGULATOR_MAX14577) += max14577.o
 obj-$(CONFIG_REGULATOR_MAX1586) += max1586.o
 obj-$(CONFIG_REGULATOR_MAX8649)	+= max8649.o

drivers/regulator/anatop-regulator.c

@@ -300,7 +300,7 @@ static int anatop_regulator_probe(struct platform_device *pdev)
 	return 0;
 }
 
-static struct of_device_id of_anatop_regulator_match_tbl[] = {
+static const struct of_device_id of_anatop_regulator_match_tbl[] = {
 	{ .compatible = "fsl,anatop-regulator", },
 	{ /* end */ }
 };

drivers/regulator/core.c

@@ -3458,7 +3458,7 @@ regulator_register(const struct regulator_desc *regulator_desc,
 
 	/* register with sysfs */
 	rdev->dev.class = &regulator_class;
-	rdev->dev.of_node = config->of_node;
+	rdev->dev.of_node = of_node_get(config->of_node);
 	rdev->dev.parent = dev;
 	dev_set_name(&rdev->dev, "regulator.%d",
 		     atomic_inc_return(&regulator_no) - 1);
@@ -3600,6 +3600,7 @@ void regulator_unregister(struct regulator_dev *rdev)
 	list_del(&rdev->list);
 	kfree(rdev->constraints);
 	regulator_ena_gpio_free(rdev);
+	of_node_put(rdev->dev.of_node);
 	device_unregister(&rdev->dev);
 	mutex_unlock(&regulator_list_mutex);
 }

drivers/regulator/fixed.c

@@ -50,7 +50,6 @@ of_get_fixed_voltage_config(struct device *dev)
 {
 	struct fixed_voltage_config *config;
 	struct device_node *np = dev->of_node;
-	const __be32 *delay;
 	struct regulator_init_data *init_data;
 
 	config = devm_kzalloc(dev, sizeof(struct fixed_voltage_config),
@@ -91,15 +90,11 @@ of_get_fixed_voltage_config(struct device *dev)
 	if ((config->gpio == -ENODEV) || (config->gpio == -EPROBE_DEFER))
 		return ERR_PTR(-EPROBE_DEFER);
 
-	delay = of_get_property(np, "startup-delay-us", NULL);
-	if (delay)
-		config->startup_delay = be32_to_cpu(*delay);
+	of_property_read_u32(np, "startup-delay-us", &config->startup_delay);
 
-	if (of_find_property(np, "enable-active-high", NULL))
-		config->enable_high = true;
-
-	if (of_find_property(np, "gpio-open-drain", NULL))
-		config->gpio_is_open_drain = true;
+	config->enable_high = of_property_read_bool(np, "enable-active-high");
+	config->gpio_is_open_drain = of_property_read_bool(np,
+							   "gpio-open-drain");
 
 	if (of_find_property(np, "vin-supply", NULL))
 		config->input_supply = "vin";