---

yaml
---
r: 310388
b: refs/heads/master
c: 233e562
h: refs/heads/master
v: v3

[refs]

@@ -1,2 +1,2 @@
 ---
-refs/heads/master: a3936249694775d8fb25d19ddf0ed6263e33dd14
+refs/heads/master: 233e562eac549f4f719176bbddeb50c3f17a9c8d

trunk/Documentation/ABI/testing/sysfs-class-mtd

@@ -123,3 +123,54 @@ Description:
 		half page, or a quarter page).
 
 		In the case of ECC NOR, it is the ECC block size.
+
+What:		/sys/class/mtd/mtdX/ecc_strength
+Date:		April 2012
+KernelVersion:	3.4
+Contact:	linux-mtd@lists.infradead.org
+Description:
+		Maximum number of bit errors that the device is capable of
+		correcting within each region covering an ecc step.  This will
+		always be a non-negative integer.  Note that some devices will
+		have multiple ecc steps within each writesize region.
+
+		In the case of devices lacking any ECC capability, it is 0.
+
+What:		/sys/class/mtd/mtdX/bitflip_threshold
+Date:		April 2012
+KernelVersion:	3.4
+Contact:	linux-mtd@lists.infradead.org
+Description:
+		This allows the user to examine and adjust the criteria by which
+		mtd returns -EUCLEAN from mtd_read().  If the maximum number of
+		bit errors that were corrected on any single region comprising
+		an ecc step (as reported by the driver) equals or exceeds this
+		value, -EUCLEAN is returned.  Otherwise, absent an error, 0 is
+		returned.  Higher layers (e.g., UBI) use this return code as an
+		indication that an erase block may be degrading and should be
+		scrutinized as a candidate for being marked as bad.
+
+		The initial value may be specified by the flash device driver.
+		If not, then the default value is ecc_strength.
+
+		The introduction of this feature brings a subtle change to the
+		meaning of the -EUCLEAN return code.  Previously, it was
+		interpreted to mean simply "one or more bit errors were
+		corrected".  Its new interpretation can be phrased as "a
+		dangerously high number of bit errors were corrected on one or
+		more regions comprising an ecc step".  The precise definition of
+		"dangerously high" can be adjusted by the user with
+		bitflip_threshold.  Users are discouraged from doing this,
+		however, unless they know what they are doing and have intimate
+		knowledge of the properties of their device.  Broadly speaking,
+		bitflip_threshold should be low enough to detect genuine erase
+		block degradation, but high enough to avoid the consequences of
+		a persistent return value of -EUCLEAN on devices where sticky
+		bitflips occur.  Note that if bitflip_threshold exceeds
+		ecc_strength, -EUCLEAN is never returned by mtd_read().
+		Conversely, if bitflip_threshold is zero, -EUCLEAN is always
+		returned, absent a hard error.
+
+		This is generally applicable only to NAND flash devices with ECC
+		capability.  It is ignored on devices lacking ECC capability;
+		i.e., devices for which ecc_strength is zero.

trunk/Documentation/DocBook/mtdnand.tmpl

@@ -1119,8 +1119,6 @@ in this page</entry>
 		These constants are defined in nand.h. They are ored together to describe
 		the chip functionality.
      		<programlisting>
-/* Chip can not auto increment pages */
-#define NAND_NO_AUTOINCR	0x00000001
 /* Buswitdh is 16 bit */
 #define NAND_BUSWIDTH_16	0x00000002
 /* Device supports partial programming without padding */

trunk/Documentation/arm/OMAP/DSS

@@ -47,6 +47,51 @@ flexible way to enable non-common multi-display configuration. In addition to
 modelling the hardware overlays, omapdss supports virtual overlays and overlay
 managers. These can be used when updating a display with CPU or system DMA.
 
+omapdss driver support for audio
+--------------------------------
+There exist several display technologies and standards that support audio as
+well. Hence, it is relevant to update the DSS device driver to provide an audio
+interface that may be used by an audio driver or any other driver interested in
+the functionality.
+
+The audio_enable function is intended to prepare the relevant
+IP for playback (e.g., enabling an audio FIFO, taking in/out of reset
+some IP, enabling companion chips, etc). It is intended to be called before
+audio_start. The audio_disable function performs the reverse operation and is
+intended to be called after audio_stop.
+
+While a given DSS device driver may support audio, it is possible that for
+certain configurations audio is not supported (e.g., an HDMI display using a
+VESA video timing). The audio_supported function is intended to query whether
+the current configuration of the display supports audio.
+
+The audio_config function is intended to configure all the relevant audio
+parameters of the display. In order to make the function independent of any
+specific DSS device driver, a struct omap_dss_audio is defined. Its purpose
+is to contain all the required parameters for audio configuration. At the
+moment, such structure contains pointers to IEC-60958 channel status word
+and CEA-861 audio infoframe structures. This should be enough to support
+HDMI and DisplayPort, as both are based on CEA-861 and IEC-60958.
+
+The audio_enable/disable, audio_config and audio_supported functions could be
+implemented as functions that may sleep. Hence, they should not be called
+while holding a spinlock or a readlock.
+
+The audio_start/audio_stop function is intended to effectively start/stop audio
+playback after the configuration has taken place. These functions are designed
+to be used in an atomic context. Hence, audio_start should return quickly and be
+called only after all the needed resources for audio playback (audio FIFOs,
+DMA channels, companion chips, etc) have been enabled to begin data transfers.
+audio_stop is designed to only stop the audio transfers. The resources used
+for playback are released using audio_disable.
+
+The enum omap_dss_audio_state may be used to help the implementations of
+the interface to keep track of the audio state. The initial state is _DISABLED;
+then, the state transitions to _CONFIGURED, and then, when it is ready to
+play audio, to _ENABLED. The state _PLAYING is used when the audio is being
+rendered.
+
+
 Panel and controller drivers
 ----------------------------
 
@@ -156,6 +201,7 @@ timings		Display timings (pixclock,xres/hfp/hbp/hsw,yres/vfp/vbp/vsw)
 		"pal" and "ntsc"
 panel_name
 tear_elim	Tearing elimination 0=off, 1=on
+output_type	Output type (video encoder only): "composite" or "svideo"
 
 There are also some debugfs files at <debugfs>/omapdss/ which show information
 about clocks and registers.

trunk/Documentation/devicetree/bindings/mtd/gpmi-nand.txt

@@ -0,0 +1,33 @@
+* Freescale General-Purpose Media Interface (GPMI)
+
+The GPMI nand controller provides an interface to control the
+NAND flash chips. We support only one NAND chip now.
+
+Required properties:
+  - compatible : should be "fsl,<chip>-gpmi-nand"
+  - reg : should contain registers location and length for gpmi and bch.
+  - reg-names: Should contain the reg names "gpmi-nand" and "bch"
+  - interrupts : The first is the DMA interrupt number for GPMI.
+                 The second is the BCH interrupt number.
+  - interrupt-names : The interrupt names "gpmi-dma", "bch";
+  - fsl,gpmi-dma-channel : Should contain the dma channel it uses.
+
+The device tree may optionally contain sub-nodes describing partitions of the
+address space. See partition.txt for more detail.
+
+Examples:
+
+gpmi-nand@8000c000 {
+	compatible = "fsl,imx28-gpmi-nand";
+	#address-cells = <1>;
+	#size-cells = <1>;
+	reg = <0x8000c000 2000>, <0x8000a000 2000>;
+	reg-names = "gpmi-nand", "bch";
+	interrupts = <88>, <41>;
+	interrupt-names = "gpmi-dma", "bch";
+	fsl,gpmi-dma-channel = <4>;
+
+	partition@0 {
+	...
+	};
+};

trunk/Documentation/devicetree/bindings/mtd/mxc-nand.txt

@@ -0,0 +1,19 @@
+* Freescale's mxc_nand
+
+Required properties:
+- compatible: "fsl,imxXX-nand"
+- reg: address range of the nfc block
+- interrupts: irq to be used
+- nand-bus-width: see nand.txt
+- nand-ecc-mode: see nand.txt
+- nand-on-flash-bbt: see nand.txt
+
+Example:
+
+	nand@d8000000 {
+		compatible = "fsl,imx27-nand";
+		reg = <0xd8000000 0x1000>;
+		interrupts = <29>;
+		nand-bus-width = <8>;
+		nand-ecc-mode = "hw";
+	};

trunk/Documentation/vm/slub.txt

@@ -17,7 +17,7 @@ data and perform operation on the slabs. By default slabinfo only lists
 slabs that have data in them. See "slabinfo -h" for more options when
 running the command. slabinfo can be compiled with
 
-gcc -o slabinfo tools/slub/slabinfo.c
+gcc -o slabinfo tools/vm/slabinfo.c
 
 Some of the modes of operation of slabinfo require that slub debugging
 be enabled on the command line. F.e. no tracking information will be