---

yaml
---
r: 144023
b: refs/heads/master
c: 58be18c
h: refs/heads/master
i:
  144021: 6555b6e
  144019: 8cd7d51
  144015: b0d2c61
v: v3

[refs]

@@ -1,2 +1,2 @@
 ---
-refs/heads/master: e655dc8873b2390d92888095af6adad822a8b386
+refs/heads/master: 58be18c4de37b9277b045c0b5bb123a664dac9ed

trunk/Documentation/powerpc/booting-without-of.txt

@@ -43,12 +43,11 @@ Table of Contents
     2) Representing devices without a current OF specification
       a) PHY nodes
       b) Interrupt controllers
-      c) CFI or JEDEC memory-mapped NOR flash
-      d) 4xx/Axon EMAC ethernet nodes
-      e) Xilinx IP cores
-      f) USB EHCI controllers
-      g) MDIO on GPIOs
-      h) SPI busses
+      c) 4xx/Axon EMAC ethernet nodes
+      d) Xilinx IP cores
+      e) USB EHCI controllers
+      f) MDIO on GPIOs
+      g) SPI busses
 
   VII - Marvell Discovery mv64[345]6x System Controller chips
     1) The /system-controller node
@@ -999,7 +998,7 @@ compatibility.
       translation of SOC addresses for memory mapped SOC registers.
     - bus-frequency: Contains the bus frequency for the SOC node.
       Typically, the value of this field is filled in by the boot
-      loader. 
+      loader.
 
 
   Recommended properties:
@@ -1287,71 +1286,7 @@ platforms are moved over to use the flattened-device-tree model.
 		device_type = "open-pic";
 	};
 
-   c) CFI or JEDEC memory-mapped NOR flash
-
-    Flash chips (Memory Technology Devices) are often used for solid state
-    file systems on embedded devices.
-
-     - compatible : should contain the specific model of flash chip(s)
-       used, if known, followed by either "cfi-flash" or "jedec-flash"
-     - reg : Address range of the flash chip
-     - bank-width : Width (in bytes) of the flash bank.  Equal to the
-       device width times the number of interleaved chips.
-     - device-width : (optional) Width of a single flash chip.  If
-       omitted, assumed to be equal to 'bank-width'.
-     - #address-cells, #size-cells : Must be present if the flash has
-       sub-nodes representing partitions (see below).  In this case
-       both #address-cells and #size-cells must be equal to 1.
-
-    For JEDEC compatible devices, the following additional properties
-    are defined:
-
-     - vendor-id : Contains the flash chip's vendor id (1 byte).
-     - device-id : Contains the flash chip's device id (1 byte).
-
-    In addition to the information on the flash bank itself, the
-    device tree may optionally contain additional information
-    describing partitions of the flash address space.  This can be
-    used on platforms which have strong conventions about which
-    portions of the flash are used for what purposes, but which don't
-    use an on-flash partition table such as RedBoot.
-
-    Each partition is represented as a sub-node of the flash device.
-    Each node's name represents the name of the corresponding
-    partition of the flash device.
-
-    Flash partitions
-     - reg : The partition's offset and size within the flash bank.
-     - label : (optional) The label / name for this flash partition.
-       If omitted, the label is taken from the node name (excluding
-       the unit address).
-     - read-only : (optional) This parameter, if present, is a hint to
-       Linux that this flash partition should only be mounted
-       read-only.  This is usually used for flash partitions
-       containing early-boot firmware images or data which should not
-       be clobbered.
-
-    Example:
-
-	flash@ff000000 {
-		compatible = "amd,am29lv128ml", "cfi-flash";
-		reg = <ff000000 01000000>;
-		bank-width = <4>;
-		device-width = <1>;
-		#address-cells = <1>;
-		#size-cells = <1>;
-		fs@0 {
-			label = "fs";
-			reg = <0 f80000>;
-		};
-		firmware@f80000 {
-			label ="firmware";
-			reg = <f80000 80000>;
-			read-only;
-		};
-	};
-
-    d) 4xx/Axon EMAC ethernet nodes
+    c) 4xx/Axon EMAC ethernet nodes
 
     The EMAC ethernet controller in IBM and AMCC 4xx chips, and also
     the Axon bridge.  To operate this needs to interact with a ths
@@ -1499,7 +1434,7 @@ platforms are moved over to use the flattened-device-tree model.
 			   available.
 			   For Axon: 0x0000012a
 
-   e) Xilinx IP cores
+   d) Xilinx IP cores
 
    The Xilinx EDK toolchain ships with a set of IP cores (devices) for use
    in Xilinx Spartan and Virtex FPGAs.  The devices cover the whole range
@@ -1761,7 +1696,7 @@ platforms are moved over to use the flattened-device-tree model.
       listed above, nodes for these devices should include a phy-handle
       property, and may include other common network device properties
       like local-mac-address.
-      
+
       iv) Xilinx Uartlite
 
       Xilinx uartlite devices are simple fixed speed serial ports.
@@ -1793,7 +1728,7 @@ platforms are moved over to use the flattened-device-tree model.
        - reg-offset : A value of 3 is required
        - reg-shift : A value of 2 is required
 
-    f) USB EHCI controllers
+    e) USB EHCI controllers
 
     Required properties:
       - compatible : should be "usb-ehci".
@@ -1819,7 +1754,7 @@ platforms are moved over to use the flattened-device-tree model.
 		   big-endian;
 	   };
 
-   g) MDIO on GPIOs
+   f) MDIO on GPIOs
 
    Currently defined compatibles:
    - virtual,gpio-mdio
@@ -1839,7 +1774,7 @@ platforms are moved over to use the flattened-device-tree model.
 			 &qe_pio_c 6>;
 	};
 
-    h) SPI (Serial Peripheral Interface) busses
+    g) SPI (Serial Peripheral Interface) busses
 
     SPI busses can be described with a node for the SPI master device
     and a set of child nodes for each SPI slave on the bus.  For this

trunk/Documentation/powerpc/dts-bindings/mtd-physmap.txt

@@ -0,0 +1,80 @@
+CFI or JEDEC memory-mapped NOR flash
+
+Flash chips (Memory Technology Devices) are often used for solid state
+file systems on embedded devices.
+
+ - compatible : should contain the specific model of flash chip(s)
+   used, if known, followed by either "cfi-flash" or "jedec-flash"
+ - reg : Address range(s) of the flash chip(s)
+   It's possible to (optionally) define multiple "reg" tuples so that
+   non-identical NOR chips can be described in one flash node.
+ - bank-width : Width (in bytes) of the flash bank.  Equal to the
+   device width times the number of interleaved chips.
+ - device-width : (optional) Width of a single flash chip.  If
+   omitted, assumed to be equal to 'bank-width'.
+ - #address-cells, #size-cells : Must be present if the flash has
+   sub-nodes representing partitions (see below).  In this case
+   both #address-cells and #size-cells must be equal to 1.
+
+For JEDEC compatible devices, the following additional properties
+are defined:
+
+ - vendor-id : Contains the flash chip's vendor id (1 byte).
+ - device-id : Contains the flash chip's device id (1 byte).
+
+In addition to the information on the flash bank itself, the
+device tree may optionally contain additional information
+describing partitions of the flash address space.  This can be
+used on platforms which have strong conventions about which
+portions of the flash are used for what purposes, but which don't
+use an on-flash partition table such as RedBoot.
+
+Each partition is represented as a sub-node of the flash device.
+Each node's name represents the name of the corresponding
+partition of the flash device.
+
+Flash partitions
+ - reg : The partition's offset and size within the flash bank.
+ - label : (optional) The label / name for this flash partition.
+   If omitted, the label is taken from the node name (excluding
+   the unit address).
+ - read-only : (optional) This parameter, if present, is a hint to
+   Linux that this flash partition should only be mounted
+   read-only.  This is usually used for flash partitions
+   containing early-boot firmware images or data which should not
+   be clobbered.
+
+Example:
+
+	flash@ff000000 {
+		compatible = "amd,am29lv128ml", "cfi-flash";
+		reg = <ff000000 01000000>;
+		bank-width = <4>;
+		device-width = <1>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		fs@0 {
+			label = "fs";
+			reg = <0 f80000>;
+		};
+		firmware@f80000 {
+			label ="firmware";
+			reg = <f80000 80000>;
+			read-only;
+		};
+	};
+
+Here an example with multiple "reg" tuples:
+
+	flash@f0000000,0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "intel,PC48F4400P0VB", "cfi-flash";
+		reg = <0 0x00000000 0x02000000
+		       0 0x02000000 0x02000000>;
+		bank-width = <2>;
+		partition@0 {
+			label = "test-part1";
+			reg = <0 0x04000000>;
+		};
+	};

trunk/MAINTAINERS

@@ -1337,12 +1337,9 @@ L:	cbe-oss-dev@ozlabs.org
 W:	http://www.ibm.com/developerworks/power/cell/
 S:	Supported
 F:	arch/powerpc/include/asm/cell*.h
-F:	arch/powerpc/include/asm/lv1call.h
-F:	arch/powerpc/include/asm/ps3*.h
 F:	arch/powerpc/include/asm/spu*.h
 F:	arch/powerpc/oprofile/*cell*
 F:	arch/powerpc/platforms/cell/
-F:	arch/powerpc/platforms/ps3/
 
 CERTIFIED WIRELESS USB (WUSB) SUBSYSTEM:
 P:	David Vrabel
@@ -2761,7 +2758,7 @@ IDE SUBSYSTEM
 P:	Bartlomiej Zolnierkiewicz
 M:	bzolnier@gmail.com
 L:	linux-ide@vger.kernel.org
-T:	quilt kernel.org/pub/linux/kernel/people/bart/pata-2.6/
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6.git
 S:	Maintained
 F:	Documentation/ide/
 F:	drivers/ide/
@@ -3994,8 +3991,8 @@ NETWORKING [GENERAL]
 P:	David S. Miller
 M:	davem@davemloft.net
 L:	netdev@vger.kernel.org
-W:	http://linux-net.osdl.org/
-T:	git kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6.git
+W:	http://www.linuxfoundation.org/en/Net
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6.git
 S:	Maintained
 F:	net/
 F:	include/net/
@@ -4036,6 +4033,13 @@ F:	net/wireless/
 F:	include/net/ieee80211*
 F:	include/net/wireless.h
 
+NETWORKING DRIVERS
+L:	netdev@vger.kernel.org
+W:	http://www.linuxfoundation.org/en/Net
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6.git
+S:	Odd Fixes
+F:	drivers/net/
+
 NETXEN (1/10) GbE SUPPORT
 P:	Dhananjay Phadke
 M:	dhananjay@netxen.com
@@ -4507,7 +4511,9 @@ F:	arch/powerpc/include/asm/ps3*.h
 F:	arch/powerpc/platforms/ps3/
 F:	drivers/*/ps3*
 F:	drivers/ps3/
+F:	drivers/rtc/rtc-ps3.c
 F:	drivers/usb/host/*ps3.c
+F:	sound/ppc/snd_ps3*
 
 PS3VRAM DRIVER
 P:	Jim Paris

trunk/arch/ia64/kvm/kvm-ia64.c

@@ -610,20 +610,22 @@ static int __vcpu_run(struct kvm_vcpu *vcpu, struct kvm_run *kvm_run)
 	int r;
 
 again:
-	preempt_disable();
-	local_irq_disable();
-
 	if (signal_pending(current)) {
-		local_irq_enable();
-		preempt_enable();
 		r = -EINTR;
 		kvm_run->exit_reason = KVM_EXIT_INTR;
 		goto out;
 	}
 
+	/*
+	 * down_read() may sleep and return with interrupts enabled
+	 */
+	down_read(&vcpu->kvm->slots_lock);
+
+	preempt_disable();
+	local_irq_disable();
+
 	vcpu->guest_mode = 1;
 	kvm_guest_enter();
-	down_read(&vcpu->kvm->slots_lock);
 	r = vti_vcpu_run(vcpu, kvm_run);
 	if (r < 0) {
 		local_irq_enable();