Merge branch 'powerpc-next' of master.kernel.org:/pub/scm/linux/kerne…

…l/git/galak/powerpc

arch/powerpc/kernel/cpu_setup_6xx.S

@@ -17,7 +17,13 @@
 #include <asm/cache.h>
 
 _GLOBAL(__setup_cpu_603)
-	b	setup_common_caches
+	mflr	r4
+BEGIN_FTR_SECTION
+	bl	__init_fpu_registers
+END_FTR_SECTION_IFCLR(CPU_FTR_FPU_UNAVAILABLE)
+	bl	setup_common_caches
+	mtlr	r4
+	blr
 _GLOBAL(__setup_cpu_604)
 	mflr	r4
 	bl	setup_common_caches

arch/ppc/8260_io/fcc_enet.c

@@ -165,23 +165,15 @@ static int fcc_enet_set_mac_address(struct net_device *dev, void *addr);
 #ifdef CONFIG_SBC82xx
 #define F1_RXCLK	9
 #define F1_TXCLK	10
-#elif defined(CONFIG_ADS8272)
-#define F1_RXCLK	11
-#define F1_TXCLK	10
 #else
 #define F1_RXCLK	12
 #define F1_TXCLK	11
 #endif
 
 /* FCC2 Clock Source Configuration.  There are board specific.
    Can only choose from CLK13-16 */
-#ifdef CONFIG_ADS8272
-#define F2_RXCLK	15
-#define F2_TXCLK	16
-#else
 #define F2_RXCLK	13
 #define F2_TXCLK	14
-#endif
 
 /* FCC3 Clock Source Configuration.  There are board specific.
    Can only choose from CLK13-16 */
@@ -289,10 +281,7 @@ static int fcc_enet_set_mac_address(struct net_device *dev, void *addr);
 /* TQM8260 has MDIO and MDCK on PC30 and PC31 respectively */
 #define PC_MDIO		((uint)0x00000002)
 #define PC_MDCK		((uint)0x00000001)
-#elif defined(CONFIG_ADS8272)
-#define PC_MDIO		((uint)0x00002000)
-#define PC_MDCK		((uint)0x00001000)
-#elif defined(CONFIG_EST8260) || defined(CONFIG_ADS8260) || defined(CONFIG_PQ2FADS)
+#elif defined(CONFIG_EST8260) || defined(CONFIG_ADS8260)
 #define PC_MDIO		((uint)0x00400000)
 #define PC_MDCK		((uint)0x00200000)
 #else
@@ -2118,11 +2107,6 @@ init_fcc_startup(fcc_info_t *fip, struct net_device *dev)
 		printk("Can't get FCC IRQ %d\n", fip->fc_interrupt);
 
 #ifdef	PHY_INTERRUPT
-#ifdef CONFIG_ADS8272
-	if (request_irq(PHY_INTERRUPT, mii_link_interrupt, IRQF_SHARED,
-				"mii", dev) < 0)
-		printk(KERN_CRIT "Can't get MII IRQ %d\n", PHY_INTERRUPT);
-#else
 	/* Make IRQn edge triggered.  This does not work if PHY_INTERRUPT is
 	 * on Port C.
 	 */
@@ -2132,7 +2116,6 @@ init_fcc_startup(fcc_info_t *fip, struct net_device *dev)
 	if (request_irq(PHY_INTERRUPT, mii_link_interrupt, 0,
 							"mii", dev) < 0)
 		printk(KERN_CRIT "Can't get MII IRQ %d\n", PHY_INTERRUPT);
-#endif
 #endif	/* PHY_INTERRUPT */
 
 	/* Set GFMR to enable Ethernet operating mode.

arch/ppc/8xx_io/enet.c

@@ -946,29 +946,6 @@ static int __init scc_enet_init(void)
 	*((volatile uint *)BCSR1) &= ~BCSR1_ETHEN;
 #endif
 
-#ifdef CONFIG_MPC885ADS
-
-	/* Deassert PHY reset and enable the PHY.
-	 */
-	{
-		volatile uint __iomem *bcsr = ioremap(BCSR_ADDR, BCSR_SIZE);
-		uint tmp;
-
-		tmp = in_be32(bcsr + 1 /* BCSR1 */);
-		tmp |= BCSR1_ETHEN;
-		out_be32(bcsr + 1, tmp);
-		tmp = in_be32(bcsr + 4 /* BCSR4 */);
-		tmp |= BCSR4_ETH10_RST;
-		out_be32(bcsr + 4, tmp);
-		iounmap(bcsr);
-	}
-
-	/* On MPC885ADS SCC ethernet PHY defaults to the full duplex mode
-	 * upon reset. SCC is set to half duplex by default. So this
-	 * inconsistency should be better fixed by the software.
-	 */
-#endif
-
 	dev->base_addr = (unsigned long)ep;
 #if 0
 	dev->name = "CPM_ENET";

arch/ppc/Kconfig

@@ -372,22 +372,6 @@ config MPC8XXFADS
 	bool "FADS"
 	select FADS
 
-config MPC86XADS
-	bool "MPC86XADS"
-	help
-	  MPC86x Application Development System by Freescale Semiconductor.
-	  The MPC86xADS is meant to serve as a platform for s/w and h/w
-	  development around the MPC86X processor families.
-	select FADS
-
-config MPC885ADS
-	bool "MPC885ADS"
-	help
-	  Freescale Semiconductor MPC885 Application Development System (ADS).
-	  Also known as DUET.
-	  The MPC885ADS is meant to serve as a platform for s/w and h/w
-	  development around the MPC885 processor family.
-
 config TQM823L
 	bool "TQM823L"
 	help
@@ -479,53 +463,6 @@ config WINCEPT
 
 endchoice
 
-menu "Freescale Ethernet driver platform-specific options"
-	depends on FS_ENET
-
-	config MPC8xx_SECOND_ETH
-	bool "Second Ethernet channel"
-	depends on (MPC885ADS || MPC86XADS)
-	default y
-	help
-	  This enables support for second Ethernet on MPC885ADS and MPC86xADS boards.
-	  The latter will use SCC1, for 885ADS you can select it below.
-
-	choice
-		prompt "Second Ethernet channel"
-		depends on MPC8xx_SECOND_ETH
-		default MPC8xx_SECOND_ETH_FEC2
-
-		config MPC8xx_SECOND_ETH_FEC2
-		bool "FEC2"
-		depends on MPC885ADS
-		help
-		  Enable FEC2 to serve as 2-nd Ethernet channel. Note that SMC2
-		  (often 2-nd UART) will not work if this is enabled.
-
-		config MPC8xx_SECOND_ETH_SCC1
-		bool "SCC1"
-		depends on MPC86XADS
-		select MPC8xx_SCC_ENET_FIXED
-		help
-		  Enable SCC1 to serve as 2-nd Ethernet channel. Note that SMC1
-		  (often 1-nd UART) will not work if this is enabled.
-
-		config MPC8xx_SECOND_ETH_SCC3
-		bool "SCC3"
-		depends on MPC885ADS
-		help
-		  Enable SCC3 to serve as 2-nd Ethernet channel. Note that SMC1
-		  (often 1-nd UART) will not work if this is enabled.
-
-	endchoice
-
-	config MPC8xx_SCC_ENET_FIXED
-	depends on MPC8xx_SECOND_ETH_SCC
-	default n
-	bool "Use fixed MII-less mode for SCC Ethernet"
-
-endmenu
-
 choice
 	prompt "Machine Type"
 	depends on 6xx
@@ -666,9 +603,6 @@ config TQM8260
 	  End of Life: not yet :-)
 	  URL: <http://www.denx.de/PDF/TQM82xx_SPEC_Rev005.pdf>
 
-config ADS8272
-	bool "ADS8272"
-
 config PQ2FADS
 	bool "Freescale-PQ2FADS"
 	help
@@ -698,11 +632,6 @@ config EV64360
 	  platform.
 endchoice
 
-config PQ2ADS
-	bool
-	depends on ADS8272
-	default y
-
 config TQM8xxL
 	bool
 	depends on 8xx && (TQM823L || TQM850L || FPS850L || TQM855L || TQM860L)
@@ -725,15 +654,6 @@ config 8260
 	  this option means that you wish to build a kernel for a machine with
 	  an 8260 class CPU.
 
-config 8272
-	bool
-	depends on 6xx
-	default y if ADS8272
-	select 8260
-	help
-	  The MPC8272 CPM has a different internal dpram setup than other CPM2
-	  devices
-
 config CPM1
 	bool
 	depends on 8xx
@@ -1069,7 +989,7 @@ config PCI_8260
 
 config 8260_PCI9
 	bool "Enable workaround for MPC826x erratum PCI 9"
-	depends on PCI_8260 && !ADS8272
+	depends on PCI_8260
 	default y
 
 choice