Merge tag 'xceiv-for-v3.7' of git://git.kernel.org/pub/scm/linux/kern…

…el/git/balbi/usb into next/cleanup2

usb: xceiv: patches for v3.7 merge window

nop xceiv got its own header to avoid polluting otg.h. It has also
learned to work as USB2 and USB3 phys so we can use it on USB3
controllers.

Together with those two changes to nop xceiv, we're adding basic
PHY support to dwc3 driver, this is to allow platforms which actually
have a SW-controllable PHY talk to them through dwc3 driver.

We're adding a new phy driver for the OMAP architecture. This driver
is for the PHY found in OMAP4 SoCs, and a new phy driver for the
marvell architecture. An extra phy driver - for Tegra SoCs - is now
moving from arch/arm/mach-tegra* to drivers/usb/phy.

Also here, there's the creation of <linux/usb/phy.h> which should be
used from now on for PHY drivers, even those which don't support
OTG.

* tag 'xceiv-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb:
  usb: otg: mxs-phy: Fix mx23 operation
  usb: dwc3: add basic PHY support
  usb: dwc3: exynos: add nop transceiver support
  usb: dwc3: omap: add nop transceiver support
  usb: dwc3: pci: add nop transceiver support
  usb: otg: move the dereference below the NULL test
  arm: omap: phy: remove unused functions from omap-phy-internal.c
  usb: twl4030: Add device tree support for twl4030 usb
  usb: twl6030: Add dt support for twl6030 usb
  usb: otg: make twl6030_usb as a comparator driver to omap_usb2
  usb: phy: add a new driver for omap usb2 phy
  usb: phy: fix build break
  usb: move phy driver from mach-tegra to drivers/usb
  usb: otg: Move phy interface to separate file.
  usb: phy: isp1301: Remove unused static array and define
  usb: phy: mv_u3d: Add usb phy driver for mv_u3d
  usb: otg: Remove the unneeded NULL check
  usb: xceiv: nop: let it work as USB2 and USB3 phy
  usb: xceiv: create nop-usb-xceiv.h and avoid pollution on otg.h

Signed-off-by: Olof Johansson <olof@lixom.net>

Documentation/devicetree/bindings/usb/twlxxxx-usb.txt

@@ -0,0 +1,40 @@
+USB COMPARATOR OF TWL CHIPS
+
+TWL6030 USB COMPARATOR
+ - compatible : Should be "ti,twl6030-usb"
+ - interrupts : Two interrupt numbers to the cpu should be specified. First
+   interrupt number is the otg interrupt number that raises ID interrupts when
+   the controller has to act as host and the second interrupt number is the
+   usb interrupt number that raises VBUS interrupts when the controller has to
+   act as device
+ - usb-supply : phandle to the regulator device tree node. It should be vusb
+   if it is twl6030 or ldousb if it is twl6025 subclass.
+
+twl6030-usb {
+	compatible = "ti,twl6030-usb";
+	interrupts = < 4 10 >;
+};
+
+Board specific device node entry
+&twl6030-usb {
+	usb-supply = <&vusb>;
+};
+
+TWL4030 USB PHY AND COMPARATOR
+ - compatible : Should be "ti,twl4030-usb"
+ - interrupts : The interrupt numbers to the cpu should be specified. First
+   interrupt number is the otg interrupt number that raises ID interrupts
+   and VBUS interrupts. The second interrupt number is optional.
+ - <supply-name>-supply : phandle to the regulator device tree node.
+   <supply-name> should be vusb1v5, vusb1v8 and vusb3v1
+ - usb_mode : The mode used by the phy to connect to the controller. "1"
+   specifies "ULPI" mode and "2" specifies "CEA2011_3PIN" mode.
+
+twl4030-usb {
+	compatible = "ti,twl4030-usb";
+	interrupts = < 10 4 >;
+	usb1v5-supply = <&vusb1v5>;
+	usb1v8-supply = <&vusb1v8>;
+	usb3v1-supply = <&vusb3v1>;
+	usb_mode = <1>;
+};

Documentation/devicetree/bindings/usb/usb-phy.txt

@@ -0,0 +1,17 @@
+USB PHY
+
+OMAP USB2 PHY
+
+Required properties:
+ - compatible: Should be "ti,omap-usb2"
+ - reg : Address and length of the register set for the device. Also
+add the address of control module dev conf register until a driver for
+control module is added
+
+This is usually a subnode of ocp2scp to which it is connected.
+
+usb2phy@4a0ad080 {
+	compatible = "ti,omap-usb2";
+	reg = <0x4a0ad080 0x58>,
+	      <0x4a002300 0x4>;
+};

arch/arm/mach-omap2/board-omap3evm.c

@@ -32,6 +32,7 @@
 #include <linux/spi/ads7846.h>
 #include <linux/i2c/twl.h>
 #include <linux/usb/otg.h>
+#include <linux/usb/nop-usb-xceiv.h>
 #include <linux/smsc911x.h>
 
 #include <linux/wl12xx.h>

arch/arm/mach-omap2/omap_phy_internal.c

@@ -31,144 +31,6 @@
 #include <plat/usb.h>
 #include "control.h"
 
-/* OMAP control module register for UTMI PHY */
-#define CONTROL_DEV_CONF		0x300
-#define PHY_PD				0x1
-
-#define USBOTGHS_CONTROL		0x33c
-#define	AVALID				BIT(0)
-#define	BVALID				BIT(1)
-#define	VBUSVALID			BIT(2)
-#define	SESSEND				BIT(3)
-#define	IDDIG				BIT(4)
-
-static struct clk *phyclk, *clk48m, *clk32k;
-static void __iomem *ctrl_base;
-static int usbotghs_control;
-
-int omap4430_phy_init(struct device *dev)
-{
-	ctrl_base = ioremap(OMAP443X_SCM_BASE, SZ_1K);
-	if (!ctrl_base) {
-		pr_err("control module ioremap failed\n");
-		return -ENOMEM;
-	}
-	/* Power down the phy */
-	__raw_writel(PHY_PD, ctrl_base + CONTROL_DEV_CONF);
-
-	if (!dev) {
-		iounmap(ctrl_base);
-		return 0;
-	}
-
-	phyclk = clk_get(dev, "ocp2scp_usb_phy_ick");
-	if (IS_ERR(phyclk)) {
-		dev_err(dev, "cannot clk_get ocp2scp_usb_phy_ick\n");
-		iounmap(ctrl_base);
-		return PTR_ERR(phyclk);
-	}
-
-	clk48m = clk_get(dev, "ocp2scp_usb_phy_phy_48m");
-	if (IS_ERR(clk48m)) {
-		dev_err(dev, "cannot clk_get ocp2scp_usb_phy_phy_48m\n");
-		clk_put(phyclk);
-		iounmap(ctrl_base);
-		return PTR_ERR(clk48m);
-	}
-
-	clk32k = clk_get(dev, "usb_phy_cm_clk32k");
-	if (IS_ERR(clk32k)) {
-		dev_err(dev, "cannot clk_get usb_phy_cm_clk32k\n");
-		clk_put(phyclk);
-		clk_put(clk48m);
-		iounmap(ctrl_base);
-		return PTR_ERR(clk32k);
-	}
-	return 0;
-}
-
-int omap4430_phy_set_clk(struct device *dev, int on)
-{
-	static int state;
-
-	if (on && !state) {
-		/* Enable the phy clocks */
-		clk_enable(phyclk);
-		clk_enable(clk48m);
-		clk_enable(clk32k);
-		state = 1;
-	} else if (state) {
-		/* Disable the phy clocks */
-		clk_disable(phyclk);
-		clk_disable(clk48m);
-		clk_disable(clk32k);
-		state = 0;
-	}
-	return 0;
-}
-
-int omap4430_phy_power(struct device *dev, int ID, int on)
-{
-	if (on) {
-		if (ID)
-			/* enable VBUS valid, IDDIG groung */
-			__raw_writel(AVALID | VBUSVALID, ctrl_base +
-							USBOTGHS_CONTROL);
-		else
-			/*
-			 * Enable VBUS Valid, AValid and IDDIG
-			 * high impedance
-			 */
-			__raw_writel(IDDIG | AVALID | VBUSVALID,
-						ctrl_base + USBOTGHS_CONTROL);
-	} else {
-		/* Enable session END and IDIG to high impedance. */
-		__raw_writel(SESSEND | IDDIG, ctrl_base +
-					USBOTGHS_CONTROL);
-	}
-	return 0;
-}
-
-int omap4430_phy_suspend(struct device *dev, int suspend)
-{
-	if (suspend) {
-		/* Disable the clocks */
-		omap4430_phy_set_clk(dev, 0);
-		/* Power down the phy */
-		__raw_writel(PHY_PD, ctrl_base + CONTROL_DEV_CONF);
-
-		/* save the context */
-		usbotghs_control = __raw_readl(ctrl_base + USBOTGHS_CONTROL);
-	} else {
-		/* Enable the internel phy clcoks */
-		omap4430_phy_set_clk(dev, 1);
-		/* power on the phy */
-		if (__raw_readl(ctrl_base + CONTROL_DEV_CONF) & PHY_PD) {
-			__raw_writel(~PHY_PD, ctrl_base + CONTROL_DEV_CONF);
-			mdelay(200);
-		}
-
-		/* restore the context */
-		__raw_writel(usbotghs_control, ctrl_base + USBOTGHS_CONTROL);
-	}
-
-	return 0;
-}
-
-int omap4430_phy_exit(struct device *dev)
-{
-	if (ctrl_base)
-		iounmap(ctrl_base);
-	if (phyclk)
-		clk_put(phyclk);
-	if (clk48m)
-		clk_put(clk48m);
-	if (clk32k)
-		clk_put(clk32k);
-
-	return 0;
-}
-
 void am35x_musb_reset(void)
 {
 	u32	regval;

arch/arm/mach-omap2/twl-common.c

@@ -251,11 +251,6 @@ void __init omap3_pmic_get_config(struct twl4030_platform_data *pmic_data,
 
 #if defined(CONFIG_ARCH_OMAP4)
 static struct twl4030_usb_data omap4_usb_pdata = {
-	.phy_init	= omap4430_phy_init,
-	.phy_exit	= omap4430_phy_exit,
-	.phy_power	= omap4430_phy_power,
-	.phy_set_clock	= omap4430_phy_set_clk,
-	.phy_suspend	= omap4430_phy_suspend,
 };
 
 static struct regulator_init_data omap4_vdac_idata = {

arch/arm/mach-omap2/usb-musb.c

@@ -117,7 +117,4 @@ void __init usb_musb_init(struct omap_musb_board_data *musb_board_data)
 	dev->dma_mask = &musb_dmamask;
 	dev->coherent_dma_mask = musb_dmamask;
 	put_device(dev);
-
-	if (cpu_is_omap44xx())
-		omap4430_phy_init(dev);
 }

arch/arm/mach-tegra/Makefile

@@ -21,7 +21,6 @@ obj-$(CONFIG_HOTPLUG_CPU)               += hotplug.o
 obj-$(CONFIG_TEGRA_SYSTEM_DMA)		+= dma.o
 obj-$(CONFIG_CPU_FREQ)                  += cpu-tegra.o
 obj-$(CONFIG_TEGRA_PCI)			+= pcie.o
-obj-$(CONFIG_USB_SUPPORT)		+= usb_phy.o
 
 obj-$(CONFIG_ARCH_TEGRA_2x_SOC)		+= board-dt-tegra20.o
 obj-$(CONFIG_ARCH_TEGRA_3x_SOC)		+= board-dt-tegra30.o

arch/arm/mach-tegra/devices.c

@@ -27,7 +27,7 @@
 #include <mach/irqs.h>
 #include <mach/iomap.h>
 #include <mach/dma.h>
-#include <mach/usb_phy.h>
+#include <linux/usb/tegra_usb_phy.h>
 
 #include "gpio-names.h"
 #include "devices.h"

arch/arm/mach-tegra/devices.h

@@ -22,7 +22,7 @@
 #include <linux/platform_device.h>
 #include <linux/platform_data/tegra_usb.h>
 
-#include <mach/usb_phy.h>
+#include <linux/usb/tegra_usb_phy.h>
 
 extern struct tegra_ulpi_config tegra_ehci2_ulpi_phy_config;
 

drivers/usb/dwc3/core.c

@@ -50,6 +50,7 @@
 #include <linux/dma-mapping.h>
 #include <linux/of.h>
 
+#include <linux/usb/otg.h>
 #include <linux/usb/ch9.h>
 #include <linux/usb/gadget.h>
 
@@ -136,6 +137,8 @@ static void dwc3_core_soft_reset(struct dwc3 *dwc)
 	reg |= DWC3_GUSB2PHYCFG_PHYSOFTRST;
 	dwc3_writel(dwc->regs, DWC3_GUSB2PHYCFG(0), reg);
 
+	usb_phy_init(dwc->usb2_phy);
+	usb_phy_init(dwc->usb3_phy);
 	mdelay(100);
 
 	/* Clear USB3 PHY reset */
@@ -470,6 +473,18 @@ static int __devinit dwc3_probe(struct platform_device *pdev)
 		return -ENOMEM;
 	}
 
+	dwc->usb2_phy = devm_usb_get_phy(dev, USB_PHY_TYPE_USB2);
+	if (IS_ERR_OR_NULL(dwc->usb2_phy)) {
+		dev_err(dev, "no usb2 phy configured\n");
+		return -EPROBE_DEFER;
+	}
+
+	dwc->usb3_phy = devm_usb_get_phy(dev, USB_PHY_TYPE_USB3);
+	if (IS_ERR_OR_NULL(dwc->usb3_phy)) {
+		dev_err(dev, "no usb3 phy configured\n");
+		return -EPROBE_DEFER;
+	}
+
 	spin_lock_init(&dwc->lock);
 	platform_set_drvdata(pdev, dwc);
 

drivers/usb/dwc3/core.h

@@ -624,6 +624,8 @@ struct dwc3_scratchpad_array {
  * @maximum_speed: maximum speed requested (mainly for testing purposes)
  * @revision: revision register contents
  * @mode: mode of operation
+ * @usb2_phy: pointer to USB2 PHY
+ * @usb3_phy: pointer to USB3 PHY
  * @is_selfpowered: true when we are selfpowered
  * @three_stage_setup: set if we perform a three phase setup
  * @ep0_bounced: true when we used bounce buffer
@@ -667,6 +669,9 @@ struct dwc3 {
 	struct usb_gadget	gadget;
 	struct usb_gadget_driver *gadget_driver;
 
+	struct usb_phy		*usb2_phy;
+	struct usb_phy		*usb3_phy;
+
 	void __iomem		*regs;
 	size_t			regs_size;