Merge branch 'usb-next' into musb-merge

* usb-next: (132 commits)
  USB: uas: Use GFP_NOIO instead of GFP_KERNEL in I/O submission path
  USB: uas: Ensure we only bind to a UAS interface
  USB: uas: Rename sense pipe and sense urb to status pipe and status urb
  USB: uas: Use kzalloc instead of kmalloc
  USB: uas: Fix up the Sense IU
  usb: musb: core: kill unneeded #include's
  DA8xx: assign name to MUSB IRQ resource
  usb: gadget: g_ncm added
  usb: gadget: f_ncm.c added
  usb: gadget: u_ether: prepare for NCM
  usb: pch_udc: Fix setup transfers with data out
  usb: pch_udc: Fix compile error, warnings and checkpatch warnings
  usb: add ab8500 usb transceiver driver
  USB: gadget: Implement runtime PM for MSM bus glue driver
  USB: gadget: Implement runtime PM for ci13xxx gadget
  USB: gadget: Add USB controller driver for MSM SoC
  USB: gadget: Introduce ci13xxx_udc_driver struct
  USB: gadget: Initialize ci13xxx gadget device's coherent DMA mask
  USB: gadget: Fix "scheduling while atomic" bugs in ci13xxx_udc
  USB: gadget: Separate out PCI bus code from ci13xxx_udc
  ...

Documentation/usb/power-management.txt

@@ -2,7 +2,7 @@
 
 		 Alan Stern <stern@rowland.harvard.edu>
 
-			    December 11, 2009
+			    October 28, 2010
 
 
 
@@ -107,9 +107,14 @@ allowed to issue dynamic suspends.
 The user interface for controlling dynamic PM is located in the power/
 subdirectory of each USB device's sysfs directory, that is, in
 /sys/bus/usb/devices/.../power/ where "..." is the device's ID.  The
-relevant attribute files are: wakeup, control, and autosuspend.
-(There may also be a file named "level"; this file was deprecated
-as of the 2.6.35 kernel and replaced by the "control" file.)
+relevant attribute files are: wakeup, control, and
+autosuspend_delay_ms.  (There may also be a file named "level"; this
+file was deprecated as of the 2.6.35 kernel and replaced by the
+"control" file.  In 2.6.38 the "autosuspend" file will be deprecated
+and replaced by the "autosuspend_delay_ms" file.  The only difference
+is that the newer file expresses the delay in milliseconds whereas the
+older file uses seconds.  Confusingly, both files are present in 2.6.37
+but only "autosuspend" works.)
 
 	power/wakeup
 
@@ -140,33 +145,36 @@ as of the 2.6.35 kernel and replaced by the "control" file.)
 		suspended and autoresume was not allowed.  This
 		setting is no longer supported.)
 
-	power/autosuspend
+	power/autosuspend_delay_ms
 
 		This file contains an integer value, which is the
-		number of seconds the device should remain idle before
-		the kernel will autosuspend it (the idle-delay time).
-		The default is 2.  0 means to autosuspend as soon as
-		the device becomes idle, and negative values mean
-		never to autosuspend.  You can write a number to the
-		file to change the autosuspend idle-delay time.
-
-Writing "-1" to power/autosuspend and writing "on" to power/control do
-essentially the same thing -- they both prevent the device from being
-autosuspended.  Yes, this is a redundancy in the API.
+		number of milliseconds the device should remain idle
+		before the kernel will autosuspend it (the idle-delay
+		time).  The default is 2000.  0 means to autosuspend
+		as soon as the device becomes idle, and negative
+		values mean never to autosuspend.  You can write a
+		number to the file to change the autosuspend
+		idle-delay time.
+
+Writing "-1" to power/autosuspend_delay_ms and writing "on" to
+power/control do essentially the same thing -- they both prevent the
+device from being autosuspended.  Yes, this is a redundancy in the
+API.
 
 (In 2.6.21 writing "0" to power/autosuspend would prevent the device
 from being autosuspended; the behavior was changed in 2.6.22.  The
 power/autosuspend attribute did not exist prior to 2.6.21, and the
 power/level attribute did not exist prior to 2.6.22.  power/control
-was added in 2.6.34.)
+was added in 2.6.34, and power/autosuspend_delay_ms was added in
+2.6.37 but did not become functional until 2.6.38.)
 
 
 	Changing the default idle-delay time
 	------------------------------------
 
-The default autosuspend idle-delay time is controlled by a module
-parameter in usbcore.  You can specify the value when usbcore is
-loaded.  For example, to set it to 5 seconds instead of 2 you would
+The default autosuspend idle-delay time (in seconds) is controlled by
+a module parameter in usbcore.  You can specify the value when usbcore
+is loaded.  For example, to set it to 5 seconds instead of 2 you would
 do:
 
 	modprobe usbcore autosuspend=5
@@ -234,25 +242,23 @@ every device.
 
 If a driver knows that its device has proper suspend/resume support,
 it can enable autosuspend all by itself.  For example, the video
-driver for a laptop's webcam might do this, since these devices are
-rarely used and so should normally be autosuspended.
+driver for a laptop's webcam might do this (in recent kernels they
+do), since these devices are rarely used and so should normally be
+autosuspended.
 
 Sometimes it turns out that even when a device does work okay with
-autosuspend there are still problems.  For example, there are
-experimental patches adding autosuspend support to the usbhid driver,
-which manages keyboards and mice, among other things.  Tests with a
-number of keyboards showed that typing on a suspended keyboard, while
-causing the keyboard to do a remote wakeup all right, would
-nonetheless frequently result in lost keystrokes.  Tests with mice
-showed that some of them would issue a remote-wakeup request in
-response to button presses but not to motion, and some in response to
-neither.
+autosuspend there are still problems.  For example, the usbhid driver,
+which manages keyboards and mice, has autosuspend support.  Tests with
+a number of keyboards show that typing on a suspended keyboard, while
+causing the keyboard to do a remote wakeup all right, will nonetheless
+frequently result in lost keystrokes.  Tests with mice show that some
+of them will issue a remote-wakeup request in response to button
+presses but not to motion, and some in response to neither.
 
 The kernel will not prevent you from enabling autosuspend on devices
 that can't handle it.  It is even possible in theory to damage a
-device by suspending it at the wrong time -- for example, suspending a
-USB hard disk might cause it to spin down without parking the heads.
-(Highly unlikely, but possible.)  Take care.
+device by suspending it at the wrong time.  (Highly unlikely, but
+possible.)  Take care.
 
 
 	The driver interface for Power Management
@@ -336,10 +342,6 @@ autosuspend the interface's device.  When the usage counter is = 0
 then the interface is considered to be idle, and the kernel may
 autosuspend the device.
 
-(There is a similar usage counter field in struct usb_device,
-associated with the device itself rather than any of its interfaces.
-This counter is used only by the USB core.)
-
 Drivers need not be concerned about balancing changes to the usage
 counter; the USB core will undo any remaining "get"s when a driver
 is unbound from its interface.  As a corollary, drivers must not call
@@ -409,11 +411,11 @@ during autosuspend.  For example, there's not much point
 autosuspending a keyboard if the user can't cause the keyboard to do a
 remote wakeup by typing on it.  If the driver sets
 intf->needs_remote_wakeup to 1, the kernel won't autosuspend the
-device if remote wakeup isn't available or has been disabled through
-the power/wakeup attribute.  (If the device is already autosuspended,
-though, setting this flag won't cause the kernel to autoresume it.
-Normally a driver would set this flag in its probe method, at which
-time the device is guaranteed not to be autosuspended.)
+device if remote wakeup isn't available.  (If the device is already
+autosuspended, though, setting this flag won't cause the kernel to
+autoresume it.  Normally a driver would set this flag in its probe
+method, at which time the device is guaranteed not to be
+autosuspended.)
 
 If a driver does its I/O asynchronously in interrupt context, it
 should call usb_autopm_get_interface_async() before starting output and
@@ -422,20 +424,19 @@ it receives an input event, it should call
 
 	usb_mark_last_busy(struct usb_device *udev);
 
-in the event handler.  This sets udev->last_busy to the current time.
-udev->last_busy is the field used for idle-delay calculations;
-updating it will cause any pending autosuspend to be moved back.  Most
-of the usb_autopm_* routines will also set the last_busy field to the
-current time.
+in the event handler.  This tells the PM core that the device was just
+busy and therefore the next autosuspend idle-delay expiration should
+be pushed back.  Many of the usb_autopm_* routines also make this call,
+so drivers need to worry only when interrupt-driven input arrives.
 
 Asynchronous operation is always subject to races.  For example, a
-driver may call one of the usb_autopm_*_interface_async() routines at
-a time when the core has just finished deciding the device has been
-idle for long enough but not yet gotten around to calling the driver's
-suspend method.  The suspend method must be responsible for
-synchronizing with the output request routine and the URB completion
-handler; it should cause autosuspends to fail with -EBUSY if the
-driver needs to use the device.
+driver may call the usb_autopm_get_interface_async() routine at a time
+when the core has just finished deciding the device has been idle for
+long enough but not yet gotten around to calling the driver's suspend
+method.  The suspend method must be responsible for synchronizing with
+the I/O request routine and the URB completion handler; it should
+cause autosuspends to fail with -EBUSY if the driver needs to use the
+device.
 
 External suspend calls should never be allowed to fail in this way,
 only autosuspend calls.  The driver can tell them apart by checking
@@ -472,7 +473,9 @@ Firstly, a device may already be autosuspended when a system suspend
 occurs.  Since system suspends are supposed to be as transparent as
 possible, the device should remain suspended following the system
 resume.  But this theory may not work out well in practice; over time
-the kernel's behavior in this regard has changed.
+the kernel's behavior in this regard has changed.  As of 2.6.37 the
+policy is to resume all devices during a system resume and let them
+handle their own runtime suspends afterward.
 
 Secondly, a dynamic power-management event may occur as a system
 suspend is underway.  The window for this is short, since system

arch/arm/mach-davinci/usb.c

@@ -64,17 +64,19 @@ static struct resource usb_resources[] = {
 	{
 		.start          = IRQ_USBINT,
 		.flags          = IORESOURCE_IRQ,
+		.name		= "mc"
 	},
 	{
 		/* placeholder for the dedicated CPPI IRQ */
 		.flags          = IORESOURCE_IRQ,
+		.name		= "dma"
 	},
 };
 
 static u64 usb_dmamask = DMA_BIT_MASK(32);
 
 static struct platform_device usb_dev = {
-	.name           = "musb_hdrc",
+	.name           = "musb-davinci",
 	.id             = -1,
 	.dev = {
 		.platform_data		= &usb_data,
@@ -110,6 +112,7 @@ static struct resource da8xx_usb20_resources[] = {
 	{
 		.start		= IRQ_DA8XX_USB_INT,
 		.flags		= IORESOURCE_IRQ,
+		.name		= "mc",
 	},
 };
 
@@ -121,6 +124,7 @@ int __init da8xx_register_usb20(unsigned mA, unsigned potpgt)
 
 	usb_dev.resource = da8xx_usb20_resources;
 	usb_dev.num_resources = ARRAY_SIZE(da8xx_usb20_resources);
+	usb_dev.name = "musb-da8xx";
 
 	return platform_device_register(&usb_dev);
 }

arch/arm/mach-omap2/Kconfig

@@ -44,6 +44,7 @@ config ARCH_OMAP4
 	select ARM_GIC
 	select PL310_ERRATA_588369
 	select ARM_ERRATA_720789
+	select USB_ARCH_HAS_EHCI
 
 comment "OMAP Core Type"
 	depends on ARCH_OMAP2

arch/arm/mach-omap2/Makefile

@@ -168,9 +168,11 @@ obj-$(CONFIG_MACH_IGEP0030)		+= board-igep0030.o \
 obj-$(CONFIG_MACH_OMAP3_TOUCHBOOK)	+= board-omap3touchbook.o \
 					   hsmmc.o
 obj-$(CONFIG_MACH_OMAP_4430SDP)		+= board-4430sdp.o \
-					   hsmmc.o
+					   hsmmc.o \
+					   omap_phy_internal.o
 obj-$(CONFIG_MACH_OMAP4_PANDA)		+= board-omap4panda.o \
-					   hsmmc.o
+					   hsmmc.o \
+					   omap_phy_internal.o
 
 obj-$(CONFIG_MACH_OMAP3517EVM)		+= board-am3517evm.o
 

arch/arm/mach-omap2/board-4430sdp.c

@@ -42,6 +42,7 @@
 #define ETH_KS8851_IRQ			34
 #define ETH_KS8851_POWER_ON		48
 #define ETH_KS8851_QUART		138
+#define OMAP4SDP_MDM_PWR_EN_GPIO	157
 #define OMAP4_SFH7741_SENSOR_OUTPUT_GPIO	184
 #define OMAP4_SFH7741_ENABLE_GPIO		188
 
@@ -225,12 +226,29 @@ static void __init omap_4430sdp_init_irq(void)
 	omap_gpio_init();
 }
 
+static const struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
+	.port_mode[0]	= EHCI_HCD_OMAP_MODE_PHY,
+	.port_mode[1]	= EHCI_HCD_OMAP_MODE_UNKNOWN,
+	.port_mode[2]	= EHCI_HCD_OMAP_MODE_UNKNOWN,
+	.phy_reset	= false,
+	.reset_gpio_port[0]  = -EINVAL,
+	.reset_gpio_port[1]  = -EINVAL,
+	.reset_gpio_port[2]  = -EINVAL,
+};
+
 static struct omap_musb_board_data musb_board_data = {
 	.interface_type		= MUSB_INTERFACE_UTMI,
-	.mode			= MUSB_PERIPHERAL,
+	.mode			= MUSB_OTG,
 	.power			= 100,
 };
 
+static struct twl4030_usb_data omap4_usbphy_data = {
+	.phy_init	= omap4430_phy_init,
+	.phy_exit	= omap4430_phy_exit,
+	.phy_power	= omap4430_phy_power,
+	.phy_set_clock	= omap4430_phy_set_clk,
+};
+
 static struct omap2_hsmmc_info mmc[] = {
 	{
 		.mmc		= 1,
@@ -450,6 +468,7 @@ static struct twl4030_platform_data sdp4430_twldata = {
 	.vaux1		= &sdp4430_vaux1,
 	.vaux2		= &sdp4430_vaux2,
 	.vaux3		= &sdp4430_vaux3,
+	.usb		= &omap4_usbphy_data
 };
 
 static struct i2c_board_info __initdata sdp4430_i2c_boardinfo[] = {
@@ -514,11 +533,15 @@ static void __init omap_4430sdp_init(void)
 	platform_add_devices(sdp4430_devices, ARRAY_SIZE(sdp4430_devices));
 	omap_serial_init();
 	omap4_twl6030_hsmmc_init(mmc);
-	/* OMAP4 SDP uses internal transceiver so register nop transceiver */
-	usb_nop_xceiv_register();
-	/* FIXME: allow multi-omap to boot until musb is updated for omap4 */
-	if (!cpu_is_omap44xx())
-		usb_musb_init(&musb_board_data);
+
+	/* Power on the ULPI PHY */
+	if (gpio_is_valid(OMAP4SDP_MDM_PWR_EN_GPIO)) {
+		/* FIXME: Assumes pad is already muxed for GPIO mode */
+		gpio_request(OMAP4SDP_MDM_PWR_EN_GPIO, "USBB1 PHY VMDM_3V3");
+		gpio_direction_output(OMAP4SDP_MDM_PWR_EN_GPIO, 1);
+	}
+	usb_ehci_init(&ehci_pdata);
+	usb_musb_init(&musb_board_data);
 
 	status = omap_ethernet_init();
 	if (status) {

arch/arm/mach-omap2/board-n8x0.c

@@ -46,8 +46,7 @@ static struct device *mmc_device;
 #define TUSB6010_GPIO_ENABLE	0
 #define TUSB6010_DMACHAN	0x3f
 
-#if defined(CONFIG_USB_TUSB6010) || \
-	defined(CONFIG_USB_TUSB6010_MODULE)
+#ifdef CONFIG_USB_MUSB_TUSB6010
 /*
  * Enable or disable power to TUSB6010. When enabling, turn on 3.3 V and
  * 1.5 V voltage regulators of PM companion chip. Companion chip will then
@@ -134,7 +133,7 @@ static void __init n8x0_usb_init(void)
 
 static void __init n8x0_usb_init(void) {}
 
-#endif /*CONFIG_USB_TUSB6010 */
+#endif /*CONFIG_USB_MUSB_TUSB6010 */
 
 
 static struct omap2_mcspi_device_config p54spi_mcspi_config = {

arch/arm/mach-omap2/board-omap4panda.c

@@ -133,10 +133,17 @@ static void __init omap4_ehci_init(void)
 
 static struct omap_musb_board_data musb_board_data = {
 	.interface_type		= MUSB_INTERFACE_UTMI,
-	.mode			= MUSB_PERIPHERAL,
+	.mode			= MUSB_OTG,
 	.power			= 100,
 };
 
+static struct twl4030_usb_data omap4_usbphy_data = {
+	.phy_init	= omap4430_phy_init,
+	.phy_exit	= omap4430_phy_exit,
+	.phy_power	= omap4430_phy_power,
+	.phy_set_clock	= omap4430_phy_set_clk,
+};
+
 static struct omap2_hsmmc_info mmc[] = {
 	{
 		.mmc		= 1,
@@ -345,6 +352,7 @@ static struct twl4030_platform_data omap4_panda_twldata = {
 	.vaux1		= &omap4_panda_vaux1,
 	.vaux2		= &omap4_panda_vaux2,
 	.vaux3		= &omap4_panda_vaux3,
+	.usb		= &omap4_usbphy_data,
 };
 
 static struct i2c_board_info __initdata omap4_panda_i2c_boardinfo[] = {
@@ -377,9 +385,7 @@ static void __init omap4_panda_init(void)
 	/* OMAP4 Panda uses internal transceiver so register nop transceiver */
 	usb_nop_xceiv_register();
 	omap4_ehci_init();
-	/* FIXME: allow multi-omap to boot until musb is updated for omap4 */
-	if (!cpu_is_omap44xx())
-		usb_musb_init(&musb_board_data);
+	usb_musb_init(&musb_board_data);
 }
 
 static void __init omap4_panda_map_io(void)

arch/arm/mach-omap2/clock2420_data.c

@@ -1877,7 +1877,7 @@ static struct omap_clk omap2420_clks[] = {
 	CLK("omap-aes",	"ick",	&aes_ick,	CK_242X),
 	CLK(NULL,	"pka_ick",	&pka_ick,	CK_242X),
 	CLK(NULL,	"usb_fck",	&usb_fck,	CK_242X),
-	CLK("musb_hdrc",	"fck",	&osc_ck,	CK_242X),
+	CLK("musb-hdrc",	"fck",	&osc_ck,	CK_242X),
 };
 
 /*

arch/arm/mach-omap2/clock2430_data.c

@@ -1983,7 +1983,7 @@ static struct omap_clk omap2430_clks[] = {
 	CLK("omap-aes",	"ick",	&aes_ick,	CK_243X),
 	CLK(NULL,	"pka_ick",	&pka_ick,	CK_243X),
 	CLK(NULL,	"usb_fck",	&usb_fck,	CK_243X),
-	CLK("musb_hdrc",	"ick",	&usbhs_ick,	CK_243X),
+	CLK("musb-omap2430",	"ick",	&usbhs_ick,	CK_243X),
 	CLK("mmci-omap-hs.0", "ick",	&mmchs1_ick,	CK_243X),
 	CLK("mmci-omap-hs.0", "fck",	&mmchs1_fck,	CK_243X),
 	CLK("mmci-omap-hs.1", "ick",	&mmchs2_ick,	CK_243X),