---

yaml
---
r: 343162
b: refs/heads/master
c: ce6dd5d
h: refs/heads/master
v: v3

[refs]

@@ -1,2 +1,2 @@
 ---
-refs/heads/master: 64e481603ab46bcd1466fdaffca50f25bf123f83
+refs/heads/master: ce6dd5da9dfcf9232df09d8d486cd6ed25e29cdc

trunk/Documentation/cgroups/memory.txt

@@ -466,6 +466,10 @@ Note:
 5.3 swappiness
 
 Similar to /proc/sys/vm/swappiness, but affecting a hierarchy of groups only.
+Please note that unlike the global swappiness, memcg knob set to 0
+really prevents from any swapping even if there is a swap storage
+available. This might lead to memcg OOM killer if there are no file
+pages to reclaim.
 
 Following cgroups' swappiness can't be changed.
 - root cgroup (uses /proc/sys/vm/swappiness).

trunk/Documentation/devicetree/bindings/regulator/gpio-regulator.txt

@@ -0,0 +1,37 @@
+GPIO controlled regulators
+
+Required properties:
+- compatible		: Must be "regulator-gpio".
+- states		: Selection of available voltages and GPIO configs.
+                          if there are no states, then use a fixed regulator
+
+Optional properties:
+- enable-gpio		: GPIO to use to enable/disable the regulator.
+- gpios			: GPIO group used to control voltage.
+- startup-delay-us	: Startup time in microseconds.
+- enable-active-high	: Polarity of GPIO is active high (default is low).
+
+Any property defined as part of the core regulator binding defined in
+regulator.txt can also be used.
+
+Example:
+
+	mmciv: gpio-regulator {
+		compatible = "regulator-gpio";
+
+		regulator-name = "mmci-gpio-supply";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <2600000>;
+		regulator-boot-on;
+
+		enable-gpio = <&gpio0 23 0x4>;
+		gpios = <&gpio0 24 0x4
+			 &gpio0 25 0x4>;
+		states = <1800000 0x3
+			  2200000 0x2
+			  2600000 0x1
+			  2900000 0x0>;
+
+		startup-delay-us = <100000>;
+		enable-active-high;
+	};

trunk/Documentation/devicetree/bindings/regulator/max8925-regulator.txt

@@ -0,0 +1,40 @@
+Max8925 Voltage regulators
+
+Required nodes:
+-nodes:
+  - SDV1 for SDV SDV1
+  - SDV2 for SDV SDV2
+  - SDV3 for SDV SDV3
+  - LDO1 for LDO LDO1
+  - LDO2 for LDO LDO2
+  - LDO3 for LDO LDO3
+  - LDO4 for LDO LDO4
+  - LDO5 for LDO LDO5
+  - LDO6 for LDO LDO6
+  - LDO7 for LDO LDO7
+  - LDO8 for LDO LDO8
+  - LDO9 for LDO LDO9
+  - LDO10 for LDO LDO10
+  - LDO11 for LDO LDO11
+  - LDO12 for LDO LDO12
+  - LDO13 for LDO LDO13
+  - LDO14 for LDO LDO14
+  - LDO15 for LDO LDO15
+  - LDO16 for LDO LDO16
+  - LDO17 for LDO LDO17
+  - LDO18 for LDO LDO18
+  - LDO19 for LDO LDO19
+  - LDO20 for LDO LDO20
+
+Optional properties:
+- Any optional property defined in bindings/regulator/regulator.txt
+
+Example:
+
+	SDV1 {
+		regulator-min-microvolt = <637500>;
+		regulator-max-microvolt = <1425000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+

trunk/Documentation/devicetree/bindings/regulator/vexpress.txt

@@ -0,0 +1,32 @@
+Versatile Express voltage regulators
+------------------------------------
+
+Requires node properties:
+- "compatible" value: "arm,vexpress-volt"
+- "arm,vexpress-sysreg,func" when controlled via vexpress-sysreg
+  (see Documentation/devicetree/bindings/arm/vexpress-sysreg.txt
+  for more details)
+
+Required regulator properties:
+- "regulator-name"
+- "regulator-always-on"
+
+Optional regulator properties:
+- "regulator-min-microvolt"
+- "regulator-max-microvolt"
+
+See Documentation/devicetree/bindings/regulator/regulator.txt
+for more details about the regulator properties.
+
+When no "regulator-[min|max]-microvolt" properties are defined,
+the device is treated as fixed (or rather "read-only") regulator.
+
+Example:
+	volt@0 {
+		compatible = "arm,vexpress-volt";
+		arm,vexpress-sysreg,func = <2 0>;
+		regulator-name = "Cores";
+		regulator-min-microvolt = <800000>;
+		regulator-max-microvolt = <1050000>;
+		regulator-always-on;
+	};

trunk/Documentation/filesystems/proc.txt

@@ -33,7 +33,7 @@ Table of Contents
   2	Modifying System Parameters
 
   3	Per-Process Parameters
-  3.1	/proc/<pid>/oom_score_adj - Adjust the oom-killer
+  3.1	/proc/<pid>/oom_adj & /proc/<pid>/oom_score_adj - Adjust the oom-killer
 								score
   3.2	/proc/<pid>/oom_score - Display current oom-killer score
   3.3	/proc/<pid>/io - Display the IO accounting fields
@@ -1320,10 +1320,10 @@ of the kernel.
 CHAPTER 3: PER-PROCESS PARAMETERS
 ------------------------------------------------------------------------------
 
-3.1 /proc/<pid>/oom_score_adj- Adjust the oom-killer score
+3.1 /proc/<pid>/oom_adj & /proc/<pid>/oom_score_adj- Adjust the oom-killer score
 --------------------------------------------------------------------------------
 
-This file can be used to adjust the badness heuristic used to select which
+These file can be used to adjust the badness heuristic used to select which
 process gets killed in out of memory conditions.
 
 The badness heuristic assigns a value to each candidate task ranging from 0
@@ -1361,6 +1361,12 @@ same system, cpuset, mempolicy, or memory controller resources to use at least
 equivalent to discounting 50% of the task's allowed memory from being considered
 as scoring against the task.
 
+For backwards compatibility with previous kernels, /proc/<pid>/oom_adj may also
+be used to tune the badness score.  Its acceptable values range from -16
+(OOM_ADJUST_MIN) to +15 (OOM_ADJUST_MAX) and a special value of -17
+(OOM_DISABLE) to disable oom killing entirely for that task.  Its value is
+scaled linearly with /proc/<pid>/oom_score_adj.
+
 The value of /proc/<pid>/oom_score_adj may be reduced no lower than the last
 value set by a CAP_SYS_RESOURCE process. To reduce the value any lower
 requires CAP_SYS_RESOURCE.
@@ -1375,7 +1381,9 @@ minimal amount of work.
 -------------------------------------------------------------
 
 This file can be used to check the current score used by the oom-killer is for
-any given <pid>.
+any given <pid>. Use it together with /proc/<pid>/oom_score_adj to tune which
+process should be killed in an out-of-memory situation.
+
 
 3.3  /proc/<pid>/io - Display the IO accounting fields
 -------------------------------------------------------

trunk/Documentation/networking/netdev-features.txt

@@ -164,4 +164,4 @@ read the CRC recorded by the NIC on receipt of the packet.
 This requests that the NIC receive all possible frames, including errored
 frames (such as bad FCS, etc).  This can be helpful when sniffing a link with
 bad packets on it.  Some NICs may receive more packets if also put into normal
-PROMISC mdoe.
+PROMISC mode.

trunk/MAINTAINERS

@@ -3598,16 +3598,58 @@ F:	drivers/hid/hid-hyperv.c
 F:	drivers/net/hyperv/
 F:	drivers/staging/hv/
 
+I2C OVER PARALLEL PORT
+M:	Jean Delvare <khali@linux-fr.org>
+L:	linux-i2c@vger.kernel.org
+S:	Maintained
+F:	Documentation/i2c/busses/i2c-parport
+F:	Documentation/i2c/busses/i2c-parport-light
+F:	drivers/i2c/busses/i2c-parport.c
+F:	drivers/i2c/busses/i2c-parport-light.c
+
+I2C/SMBUS CONTROLLER DRIVERS FOR PC
+M:	Jean Delvare <khali@linux-fr.org>
+L:	linux-i2c@vger.kernel.org
+S:	Maintained
+F:	Documentation/i2c/busses/i2c-ali1535
+F:	Documentation/i2c/busses/i2c-ali1563
+F:	Documentation/i2c/busses/i2c-ali15x3
+F:	Documentation/i2c/busses/i2c-amd756
+F:	Documentation/i2c/busses/i2c-amd8111
+F:	Documentation/i2c/busses/i2c-i801
+F:	Documentation/i2c/busses/i2c-nforce2
+F:	Documentation/i2c/busses/i2c-piix4
+F:	Documentation/i2c/busses/i2c-sis5595
+F:	Documentation/i2c/busses/i2c-sis630
+F:	Documentation/i2c/busses/i2c-sis96x
+F:	Documentation/i2c/busses/i2c-via
+F:	Documentation/i2c/busses/i2c-viapro
+F:	drivers/i2c/busses/i2c-ali1535.c
+F:	drivers/i2c/busses/i2c-ali1563.c
+F:	drivers/i2c/busses/i2c-ali15x3.c
+F:	drivers/i2c/busses/i2c-amd756.c
+F:	drivers/i2c/busses/i2c-amd756-s4882.c
+F:	drivers/i2c/busses/i2c-amd8111.c
+F:	drivers/i2c/busses/i2c-i801.c
+F:	drivers/i2c/busses/i2c-isch.c
+F:	drivers/i2c/busses/i2c-nforce2.c
+F:	drivers/i2c/busses/i2c-nforce2-s4985.c
+F:	drivers/i2c/busses/i2c-piix4.c
+F:	drivers/i2c/busses/i2c-sis5595.c
+F:	drivers/i2c/busses/i2c-sis630.c
+F:	drivers/i2c/busses/i2c-sis96x.c
+F:	drivers/i2c/busses/i2c-via.c
+F:	drivers/i2c/busses/i2c-viapro.c
+
 I2C/SMBUS STUB DRIVER
 M:	"Mark M. Hoffman" <mhoffman@lightlink.com>
 L:	linux-i2c@vger.kernel.org
 S:	Maintained
 F:	drivers/i2c/busses/i2c-stub.c
 
 I2C SUBSYSTEM
-M:	"Jean Delvare (PC drivers, core)" <khali@linux-fr.org>
+M:	Wolfram Sang <w.sang@pengutronix.de>
 M:	"Ben Dooks (embedded platforms)" <ben-linux@fluff.org>
-M:	"Wolfram Sang (embedded platforms)" <w.sang@pengutronix.de>
 L:	linux-i2c@vger.kernel.org
 W:	http://i2c.wiki.kernel.org/
 T:	quilt kernel.org/pub/linux/kernel/people/jdelvare/linux-2.6/jdelvare-i2c/
@@ -3618,6 +3660,13 @@ F:	drivers/i2c/
 F:	include/linux/i2c.h
 F:	include/linux/i2c-*.h
 
+I2C-TAOS-EVM DRIVER
+M:	Jean Delvare <khali@linux-fr.org>
+L:	linux-i2c@vger.kernel.org
+S:	Maintained
+F:	Documentation/i2c/busses/i2c-taos-evm
+F:	drivers/i2c/busses/i2c-taos-evm.c
+
 I2C-TINY-USB DRIVER
 M:	Till Harbaum <till@harbaum.org>
 L:	linux-i2c@vger.kernel.org
@@ -7210,6 +7259,14 @@ L:	linux-xtensa@linux-xtensa.org
 S:	Maintained
 F:	arch/xtensa/
 
+THERMAL
+M:      Zhang Rui <rui.zhang@intel.com>
+L:      linux-pm@vger.kernel.org
+T:      git git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux.git
+S:      Supported
+F:      drivers/thermal/
+F:      include/linux/thermal.h
+
 THINKPAD ACPI EXTRAS DRIVER
 M:	Henrique de Moraes Holschuh <ibm-acpi@hmh.eng.br>
 L:	ibm-acpi-devel@lists.sourceforge.net
@@ -7887,13 +7944,6 @@ M:	Roger Luethi <rl@hellgate.ch>
 S:	Maintained
 F:	drivers/net/ethernet/via/via-rhine.c
 
-VIAPRO SMBUS DRIVER
-M:	Jean Delvare <khali@linux-fr.org>
-L:	linux-i2c@vger.kernel.org
-S:	Maintained
-F:	Documentation/i2c/busses/i2c-viapro
-F:	drivers/i2c/busses/i2c-viapro.c
-
 VIA SD/MMC CARD CONTROLLER DRIVER
 M:	Bruce Chang <brucechang@via.com.tw>
 M:	Harald Welte <HaraldWelte@viatech.com>

trunk/Makefile

@@ -1,7 +1,7 @@
 VERSION = 3
 PATCHLEVEL = 7
 SUBLEVEL = 0
-EXTRAVERSION = -rc5
+EXTRAVERSION = -rc6
 NAME = Terrified Chipmunk
 
 # *DOCUMENTATION*

trunk/arch/arm/boot/Makefile

@@ -33,7 +33,7 @@ ifeq ($(CONFIG_XIP_KERNEL),y)
 
 $(obj)/xipImage: vmlinux FORCE
 	$(call if_changed,objcopy)
-	$(kecho) '  Kernel: $@ is ready (physical address: $(CONFIG_XIP_PHYS_ADDR))'
+	@$(kecho) '  Kernel: $@ is ready (physical address: $(CONFIG_XIP_PHYS_ADDR))'
 
 $(obj)/Image $(obj)/zImage: FORCE
 	@echo 'Kernel configured for XIP (CONFIG_XIP_KERNEL=y)'
@@ -48,14 +48,14 @@ $(obj)/xipImage: FORCE
 
 $(obj)/Image: vmlinux FORCE
 	$(call if_changed,objcopy)
-	$(kecho) '  Kernel: $@ is ready'
+	@$(kecho) '  Kernel: $@ is ready'
 
 $(obj)/compressed/vmlinux: $(obj)/Image FORCE
 	$(Q)$(MAKE) $(build)=$(obj)/compressed $@
 
 $(obj)/zImage:	$(obj)/compressed/vmlinux FORCE
 	$(call if_changed,objcopy)
-	$(kecho) '  Kernel: $@ is ready'
+	@$(kecho) '  Kernel: $@ is ready'
 
 endif
 
@@ -90,15 +90,15 @@ fi
 $(obj)/uImage:	$(obj)/zImage FORCE
 	@$(check_for_multiple_loadaddr)
 	$(call if_changed,uimage)
-	$(kecho) '  Image $@ is ready'
+	@$(kecho) '  Image $@ is ready'
 
 $(obj)/bootp/bootp: $(obj)/zImage initrd FORCE
 	$(Q)$(MAKE) $(build)=$(obj)/bootp $@
 	@:
 
 $(obj)/bootpImage: $(obj)/bootp/bootp FORCE
 	$(call if_changed,objcopy)
-	$(kecho) '  Kernel: $@ is ready'
+	@$(kecho) '  Kernel: $@ is ready'
 
 PHONY += initrd FORCE
 initrd:

trunk/arch/arm/boot/dts/tegra30.dtsi

@@ -73,8 +73,8 @@
 
 	pinmux: pinmux {
 		compatible = "nvidia,tegra30-pinmux";
-		reg = <0x70000868 0xd0    /* Pad control registers */
-		       0x70003000 0x3e0>; /* Mux registers */
+		reg = <0x70000868 0xd4    /* Pad control registers */
+		       0x70003000 0x3e4>; /* Mux registers */
 	};
 
 	serial@70006000 {

trunk/arch/arm/mach-at91/at91rm9200_devices.c

@@ -68,7 +68,7 @@ void __init at91_add_device_usbh(struct at91_usbh_data *data)
 
 	/* Enable overcurrent notification */
 	for (i = 0; i < data->ports; i++) {
-		if (data->overcurrent_pin[i])
+		if (gpio_is_valid(data->overcurrent_pin[i]))
 			at91_set_gpio_input(data->overcurrent_pin[i], 1);
 	}
 

trunk/arch/arm/mach-at91/at91sam9260_devices.c

@@ -72,7 +72,7 @@ void __init at91_add_device_usbh(struct at91_usbh_data *data)
 
 	/* Enable overcurrent notification */
 	for (i = 0; i < data->ports; i++) {
-		if (data->overcurrent_pin[i])
+		if (gpio_is_valid(data->overcurrent_pin[i]))
 			at91_set_gpio_input(data->overcurrent_pin[i], 1);
 	}
 

trunk/arch/arm/mach-at91/at91sam9261_devices.c

@@ -72,7 +72,7 @@ void __init at91_add_device_usbh(struct at91_usbh_data *data)
 
 	/* Enable overcurrent notification */
 	for (i = 0; i < data->ports; i++) {
-		if (data->overcurrent_pin[i])
+		if (gpio_is_valid(data->overcurrent_pin[i]))
 			at91_set_gpio_input(data->overcurrent_pin[i], 1);
 	}
 

trunk/arch/arm/mach-at91/at91sam9263_devices.c

@@ -78,7 +78,7 @@ void __init at91_add_device_usbh(struct at91_usbh_data *data)
 
 	/* Enable overcurrent notification */
 	for (i = 0; i < data->ports; i++) {
-		if (data->overcurrent_pin[i])
+		if (gpio_is_valid(data->overcurrent_pin[i]))
 			at91_set_gpio_input(data->overcurrent_pin[i], 1);
 	}