---

yaml
---
r: 322070
b: refs/heads/master
c: a484147
h: refs/heads/master
v: v3

[refs]

@@ -1,2 +1,2 @@
 ---
-refs/heads/master: 991b3137f21e13db4711f313edbe67d49bed795b
+refs/heads/master: a484147a52e6910d990ae7cf2a5d16b5bc58dcbe

trunk/Documentation/ABI/obsolete/proc-sys-vm-nr_pdflush_threads

@@ -0,0 +1,5 @@
+What:		/proc/sys/vm/nr_pdflush_threads
+Date:		June 2012
+Contact:	Wanpeng Li <liwp@linux.vnet.ibm.com>
+Description: Since pdflush is replaced by per-BDI flusher, the interface of old pdflush
+             exported in /proc/sys/vm/ should be removed.

trunk/Documentation/ABI/testing/sysfs-devices-platform-sh_mobile_lcdc_fb

@@ -0,0 +1,44 @@
+What:		/sys/devices/platform/sh_mobile_lcdc_fb.[0-3]/graphics/fb[0-9]/ovl_alpha
+Date:		May 2012
+Contact:	Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+Description:
+		This file is only available on fb[0-9] devices corresponding
+		to overlay planes.
+
+		Stores the alpha blending value for the overlay. Values range
+		from 0 (transparent) to 255 (opaque). The value is ignored if
+		the mode is not set to Alpha Blending.
+
+What:		/sys/devices/platform/sh_mobile_lcdc_fb.[0-3]/graphics/fb[0-9]/ovl_mode
+Date:		May 2012
+Contact:	Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+Description:
+		This file is only available on fb[0-9] devices corresponding
+		to overlay planes.
+
+		Selects the composition mode for the overlay. Possible values
+		are
+
+		0 - Alpha Blending
+		1 - ROP3
+
+What:		/sys/devices/platform/sh_mobile_lcdc_fb.[0-3]/graphics/fb[0-9]/ovl_position
+Date:		May 2012
+Contact:	Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+Description:
+		This file is only available on fb[0-9] devices corresponding
+		to overlay planes.
+
+		Stores the x,y overlay position on the display in pixels. The
+		position format is `[0-9]+,[0-9]+'.
+
+What:		/sys/devices/platform/sh_mobile_lcdc_fb.[0-3]/graphics/fb[0-9]/ovl_rop3
+Date:		May 2012
+Contact:	Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+Description:
+		This file is only available on fb[0-9] devices corresponding
+		to overlay planes.
+
+		Stores the raster operation (ROP3) for the overlay. Values
+		range from 0 to 255. The value is ignored if the mode is not
+		set to ROP3.

trunk/Documentation/ABI/testing/sysfs-platform-ideapad-laptop

@@ -5,4 +5,15 @@ Contact:	"Ike Panhc <ike.pan@canonical.com>"
 Description:
 		Control the power of camera module. 1 means on, 0 means off.
 
+What:		/sys/devices/platform/ideapad/fan_mode
+Date:		June 2012
+KernelVersion:	3.6
+Contact:	"Maxim Mikityanskiy <maxtram95@gmail.com>"
+Description:
+		Change fan mode
+		There are four available modes:
+			* 0 -> Super Silent Mode
+			* 1 -> Standard Mode
+			* 2 -> Dust Cleaning
+			* 4 -> Efficient Thermal Dissipation Mode
 

trunk/Documentation/DocBook/filesystems.tmpl

@@ -224,8 +224,8 @@ all your transactions.
 </para>
 
 <para>
-Then at umount time , in your put_super() (2.4) or write_super() (2.5)
-you can then call journal_destroy() to clean up your in-core journal object.
+Then at umount time , in your put_super() you can then call journal_destroy()
+to clean up your in-core journal object.
 </para>
 
 <para>

trunk/Documentation/IRQ-domain.txt

@@ -93,6 +93,7 @@ Linux IRQ number into the hardware.
 Most drivers cannot use this mapping.
 
 ==== Legacy ====
+irq_domain_add_simple()
 irq_domain_add_legacy()
 irq_domain_add_legacy_isa()
 
@@ -115,3 +116,7 @@ The legacy map should only be used if fixed IRQ mappings must be
 supported.  For example, ISA controllers would use the legacy map for
 mapping Linux IRQs 0-15 so that existing ISA drivers get the correct IRQ
 numbers.
+
+Most users of legacy mappings should use irq_domain_add_simple() which
+will use a legacy domain only if an IRQ range is supplied by the
+system and will otherwise use a linear domain mapping.

trunk/Documentation/block/queue-sysfs.txt

@@ -38,6 +38,13 @@ read or write requests. Note that the total allocated number may be twice
 this amount, since it applies only to reads or writes (not the accumulated
 sum).
 
+To avoid priority inversion through request starvation, a request
+queue maintains a separate request pool per each cgroup when
+CONFIG_BLK_CGROUP is enabled, and this parameter applies to each such
+per-block-cgroup request pool.  IOW, if there are N block cgroups,
+each request queue may have upto N request pools, each independently
+regulated by nr_requests.
+
 read_ahead_kb (RW)
 ------------------
 Maximum number of kilobytes to read-ahead for filesystems on this block

trunk/Documentation/cgroups/hugetlb.txt

@@ -0,0 +1,45 @@
+HugeTLB Controller
+-------------------
+
+The HugeTLB controller allows to limit the HugeTLB usage per control group and
+enforces the controller limit during page fault. Since HugeTLB doesn't
+support page reclaim, enforcing the limit at page fault time implies that,
+the application will get SIGBUS signal if it tries to access HugeTLB pages
+beyond its limit. This requires the application to know beforehand how much
+HugeTLB pages it would require for its use.
+
+HugeTLB controller can be created by first mounting the cgroup filesystem.
+
+# mount -t cgroup -o hugetlb none /sys/fs/cgroup
+
+With the above step, the initial or the parent HugeTLB group becomes
+visible at /sys/fs/cgroup. At bootup, this group includes all the tasks in
+the system. /sys/fs/cgroup/tasks lists the tasks in this cgroup.
+
+New groups can be created under the parent group /sys/fs/cgroup.
+
+# cd /sys/fs/cgroup
+# mkdir g1
+# echo $$ > g1/tasks
+
+The above steps create a new group g1 and move the current shell
+process (bash) into it.
+
+Brief summary of control files
+
+ hugetlb.<hugepagesize>.limit_in_bytes     # set/show limit of "hugepagesize" hugetlb usage
+ hugetlb.<hugepagesize>.max_usage_in_bytes # show max "hugepagesize" hugetlb  usage recorded
+ hugetlb.<hugepagesize>.usage_in_bytes     # show current res_counter usage for "hugepagesize" hugetlb
+ hugetlb.<hugepagesize>.failcnt		   # show the number of allocation failure due to HugeTLB limit
+
+For a system supporting two hugepage size (16M and 16G) the control
+files include:
+
+hugetlb.16GB.limit_in_bytes
+hugetlb.16GB.max_usage_in_bytes
+hugetlb.16GB.usage_in_bytes
+hugetlb.16GB.failcnt
+hugetlb.16MB.limit_in_bytes
+hugetlb.16MB.max_usage_in_bytes
+hugetlb.16MB.usage_in_bytes
+hugetlb.16MB.failcnt

trunk/Documentation/cgroups/memory.txt

@@ -73,6 +73,8 @@ Brief summary of control files.
 
  memory.kmem.tcp.limit_in_bytes  # set/show hard limit for tcp buf memory
  memory.kmem.tcp.usage_in_bytes  # show current tcp buf memory allocation
+ memory.kmem.tcp.failcnt            # show the number of tcp buf memory usage hits limits
+ memory.kmem.tcp.max_usage_in_bytes # show max tcp buf memory usage recorded
 
 1. History
 
@@ -187,12 +189,12 @@ the cgroup that brought it in -- this will happen on memory pressure).
 But see section 8.2: when moving a task to another cgroup, its pages may
 be recharged to the new cgroup, if move_charge_at_immigrate has been chosen.
 
-Exception: If CONFIG_CGROUP_CGROUP_MEM_RES_CTLR_SWAP is not used.
+Exception: If CONFIG_CGROUP_CGROUP_MEMCG_SWAP is not used.
 When you do swapoff and make swapped-out pages of shmem(tmpfs) to
 be backed into memory in force, charges for pages are accounted against the
 caller of swapoff rather than the users of shmem.
 
-2.4 Swap Extension (CONFIG_CGROUP_MEM_RES_CTLR_SWAP)
+2.4 Swap Extension (CONFIG_MEMCG_SWAP)
 
 Swap Extension allows you to record charge for swap. A swapped-in page is
 charged back to original page allocator if possible.
@@ -259,7 +261,7 @@ When oom event notifier is registered, event will be delivered.
   per-zone-per-cgroup LRU (cgroup's private LRU) is just guarded by
   zone->lru_lock, it has no lock of its own.
 
-2.7 Kernel Memory Extension (CONFIG_CGROUP_MEM_RES_CTLR_KMEM)
+2.7 Kernel Memory Extension (CONFIG_MEMCG_KMEM)
 
 With the Kernel memory extension, the Memory Controller is able to limit
 the amount of kernel memory used by the system. Kernel memory is fundamentally
@@ -286,8 +288,8 @@ per cgroup, instead of globally.
 
 a. Enable CONFIG_CGROUPS
 b. Enable CONFIG_RESOURCE_COUNTERS
-c. Enable CONFIG_CGROUP_MEM_RES_CTLR
-d. Enable CONFIG_CGROUP_MEM_RES_CTLR_SWAP (to use swap extension)
+c. Enable CONFIG_MEMCG
+d. Enable CONFIG_MEMCG_SWAP (to use swap extension)
 
 1. Prepare the cgroups (see cgroups.txt, Why are cgroups needed?)
 # mount -t tmpfs none /sys/fs/cgroup

trunk/Documentation/device-mapper/dm-raid.txt

@@ -27,6 +27,10 @@ The target is named "raid" and it accepts the following parameters:
 		- rotating parity N (right-to-left) with data restart
   raid6_nc	RAID6 N continue
 		- rotating parity N (right-to-left) with data continuation
+  raid10        Various RAID10 inspired algorithms chosen by additional params
+		- RAID10: Striped Mirrors (aka 'Striping on top of mirrors')
+		- RAID1E: Integrated Adjacent Stripe Mirroring
+		-  and other similar RAID10 variants
 
   Reference: Chapter 4 of
   http://www.snia.org/sites/default/files/SNIA_DDF_Technical_Position_v2.0.pdf
@@ -59,6 +63,28 @@ The target is named "raid" and it accepts the following parameters:
 		logical size of the array.  The bitmap records the device
 		synchronisation state for each region.
 
+        [raid10_copies   <# copies>]
+        [raid10_format   near]
+		These two options are used to alter the default layout of
+		a RAID10 configuration.  The number of copies is can be
+		specified, but the default is 2.  There are other variations
+		to how the copies are laid down - the default and only current
+		option is "near".  Near copies are what most people think of
+		with respect to mirroring.  If these options are left
+		unspecified, or 'raid10_copies 2' and/or 'raid10_format near'
+		are given, then the layouts for 2, 3 and 4 devices are:
+		2 drives         3 drives          4 drives
+		--------         ----------        --------------
+		A1  A1           A1  A1  A2        A1  A1  A2  A2
+		A2  A2           A2  A3  A3        A3  A3  A4  A4
+		A3  A3           A4  A4  A5        A5  A5  A6  A6
+		A4  A4           A5  A6  A6        A7  A7  A8  A8
+		..  ..           ..  ..  ..        ..  ..  ..  ..
+		The 2-device layout is equivalent 2-way RAID1.  The 4-device
+		layout is what a traditional RAID10 would look like.  The
+		3-device layout is what might be called a 'RAID1E - Integrated
+		Adjacent Stripe Mirroring'.
+
 <#raid_devs>: The number of devices composing the array.
 	Each device consists of two entries.  The first is the device
 	containing the metadata (if any); the second is the one containing the

trunk/Documentation/devicetree/bindings/arm/mrvl/intc.txt

@@ -38,3 +38,23 @@ Example:
 		reg-names = "mux status", "mux mask";
 		mrvl,intc-nr-irqs = <2>;
 	};
+
+* Marvell Orion Interrupt controller
+
+Required properties
+- compatible :  Should be "marvell,orion-intc".
+- #interrupt-cells: Specifies the number of cells needed to encode an
+  interrupt source. Supported value is <1>.
+- interrupt-controller : Declare this node to be an interrupt controller.
+- reg : Interrupt mask address. A list of 4 byte ranges, one per controller.
+        One entry in the list represents 32 interrupts.
+
+Example:
+
+	intc: interrupt-controller {
+        	compatible = "marvell,orion-intc", "marvell,intc";
+		interrupt-controller;
+		#interrupt-cells = <1>;
+                reg = <0xfed20204 0x04>,
+		      <0xfed20214 0x04>;
+        };

trunk/Documentation/devicetree/bindings/ata/marvell.txt

@@ -0,0 +1,16 @@
+* Marvell Orion SATA
+
+Required Properties:
+- compatibility : "marvell,orion-sata"
+- reg           : Address range of controller
+- interrupts    : Interrupt controller is using
+- nr-ports      : Number of SATA ports in use.
+
+Example:
+
+	sata@80000 {
+		compatible = "marvell,orion-sata";
+		reg = <0x80000 0x5000>;
+		interrupts = <21>;
+		nr-ports = <2>;
+	}

trunk/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt

@@ -27,3 +27,26 @@ Example:
 		interrupt-controller;
 		#interrupt-cells = <1>;
       };
+
+* Marvell Orion GPIO Controller
+
+Required properties:
+- compatible         : Should be "marvell,orion-gpio"
+- reg                : Address and length of the register set for controller.
+- gpio-controller    : So we know this is a gpio controller.
+- ngpio              : How many gpios this controller has.
+- interrupts	     : Up to 4 Interrupts for the controller.
+
+Optional properties:
+- mask-offset        : For SMP Orions, offset for Nth CPU
+
+Example:
+
+		gpio0: gpio@10100 {
+			compatible = "marvell,orion-gpio";
+			#gpio-cells = <2>;
+			gpio-controller;
+			reg = <0x10100 0x40>;
+			ngpio = <32>;
+			interrupts = <35>, <36>, <37>, <38>;
+		};

trunk/Documentation/devicetree/bindings/regulator/tps6586x.txt

@@ -9,9 +9,9 @@ Required properties:
 - regulators: list of regulators provided by this controller, must have
   property "regulator-compatible" to match their hardware counterparts:
   sm[0-2], ldo[0-9] and ldo_rtc
-- sm0-supply: The input supply for the SM0.
-- sm1-supply: The input supply for the SM1.
-- sm2-supply: The input supply for the SM2.
+- vin-sm0-supply: The input supply for the SM0.
+- vin-sm1-supply: The input supply for the SM1.
+- vin-sm2-supply: The input supply for the SM2.
 - vinldo01-supply: The input supply for the LDO1 and LDO2
 - vinldo23-supply: The input supply for the LDO2 and LDO3
 - vinldo4-supply: The input supply for the LDO4
@@ -30,9 +30,9 @@ Example:
 		#gpio-cells = <2>;
 		gpio-controller;
 
-		sm0-supply = <&some_reg>;
-		sm1-supply = <&some_reg>;
-		sm2-supply = <&some_reg>;
+		vin-sm0-supply = <&some_reg>;
+		vin-sm1-supply = <&some_reg>;
+		vin-sm2-supply = <&some_reg>;
 		vinldo01-supply = <...>;
 		vinldo23-supply = <...>;
 		vinldo4-supply = <...>;

trunk/Documentation/devicetree/bindings/watchdog/marvel.txt

@@ -0,0 +1,14 @@
+* Marvell Orion Watchdog Time
+
+Required Properties:
+
+- Compatibility : "marvell,orion-wdt"
+- reg		: Address of the timer registers
+
+Example:
+
+	wdt@20300 {
+		compatible = "marvell,orion-wdt";
+		reg = <0x20300 0x28>;
+		status = "okay";
+	};