[ARM] 4809/2: ixp4xx: Merge dsmg600-power.c into dsmg600-setup.c

There is no reason to have power control in a separate file from the
board setup code.  Merge it back into the board setup file and remove
superfluous header includes.

--

Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

arch/arm/mach-ixp4xx/Makefile

@@ -25,7 +25,7 @@ obj-$(CONFIG_ARCH_ADI_COYOTE)	+= coyote-setup.o
 obj-$(CONFIG_MACH_GTWX5715)	+= gtwx5715-setup.o
 obj-$(CONFIG_MACH_NSLU2)	+= nslu2-setup.o
 obj-$(CONFIG_MACH_NAS100D)	+= nas100d-setup.o
-obj-$(CONFIG_MACH_DSMG600)      += dsmg600-setup.o dsmg600-power.o
+obj-$(CONFIG_MACH_DSMG600)      += dsmg600-setup.o
 obj-$(CONFIG_MACH_GATEWAY7001)	+= gateway7001-setup.o
 obj-$(CONFIG_MACH_WG302V2)	+= wg302v2-setup.o
 

arch/arm/mach-ixp4xx/dsmg600-setup.c

@@ -1,27 +1,37 @@
 /*
  * DSM-G600 board-setup
  *
+ * Copyright (C) 2008 Rod Whitby <rod@whitby.id.au>
  * Copyright (C) 2006 Tower Technologies
- * Author: Alessandro Zummo <a.zummo@towertech.it>
  *
- * based ixdp425-setup.c:
+ * based on ixdp425-setup.c:
  *      Copyright (C) 2003-2004 MontaVista Software, Inc.
+ * based on nslu2-power.c:
+ *	Copyright (C) 2005 Tower Technologies
+ * based on nslu2-io.c:
+ *	Copyright (C) 2004 Karen Spearel
  *
  * Author: Alessandro Zummo <a.zummo@towertech.it>
+ * Author: Michael Westerhof <mwester@dls.net>
+ * Author: Rod Whitby <rod@whitby.id.au>
  * Maintainers: http://www.nslu2-linux.org/
  */
 
-#include <linux/kernel.h>
+#include <linux/irq.h>
+#include <linux/jiffies.h>
+#include <linux/timer.h>
 #include <linux/serial.h>
 #include <linux/serial_8250.h>
 #include <linux/leds.h>
+#include <linux/reboot.h>
 #include <linux/i2c.h>
 #include <linux/i2c-gpio.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/flash.h>
 #include <asm/mach/time.h>
+#include <asm/gpio.h>
 
 static struct flash_platform_data dsmg600_flash_data = {
 	.map_name		= "cfi_probe",
@@ -140,6 +150,57 @@ static void dsmg600_power_off(void)
 	gpio_line_set(DSMG600_PO_GPIO, IXP4XX_GPIO_HIGH);
 }
 
+/* This is used to make sure the power-button pusher is serious.  The button
+ * must be held until the value of this counter reaches zero.
+ */
+static int power_button_countdown;
+
+/* Must hold the button down for at least this many counts to be processed */
+#define PBUTTON_HOLDDOWN_COUNT 4 /* 2 secs */
+
+static void dsmg600_power_handler(unsigned long data);
+static DEFINE_TIMER(dsmg600_power_timer, dsmg600_power_handler, 0, 0);
+
+static void dsmg600_power_handler(unsigned long data)
+{
+	/* This routine is called twice per second to check the
+	 * state of the power button.
+	 */
+
+	if (gpio_get_value(DSMG600_PB_GPIO)) {
+
+		/* IO Pin is 1 (button pushed) */
+		if (power_button_countdown > 0)
+			power_button_countdown--;
+
+	} else {
+
+		/* Done on button release, to allow for auto-power-on mods. */
+		if (power_button_countdown == 0) {
+			/* Signal init to do the ctrlaltdel action,
+			 * this will bypass init if it hasn't started
+			 * and do a kernel_restart.
+			 */
+			ctrl_alt_del();
+
+			/* Change the state of the power LED to "blink" */
+			gpio_line_set(DSMG600_LED_PWR_GPIO, IXP4XX_GPIO_LOW);
+		} else {
+			power_button_countdown = PBUTTON_HOLDDOWN_COUNT;
+		}
+	}
+
+	mod_timer(&dsmg600_power_timer, jiffies + msecs_to_jiffies(500));
+}
+
+static irqreturn_t dsmg600_reset_handler(int irq, void *dev_id)
+{
+	/* This is the paper-clip reset, it shuts the machine down directly. */
+	machine_power_off();
+
+	return IRQ_HANDLED;
+}
+
 static void __init dsmg600_timer_init(void)
 {
     /* The xtal on this machine is non-standard. */
@@ -164,8 +225,6 @@ static void __init dsmg600_init(void)
 	dsmg600_flash_resource.end =
 		IXP4XX_EXP_BUS_BASE(0) + ixp4xx_exp_bus_size - 1;
 
-	pm_power_off = dsmg600_power_off;
-
 	i2c_register_board_info(0, dsmg600_i2c_board_info,
 				ARRAY_SIZE(dsmg600_i2c_board_info));
 
@@ -176,6 +235,29 @@ static void __init dsmg600_init(void)
         (void)platform_device_register(&dsmg600_uart);
 
 	platform_add_devices(dsmg600_devices, ARRAY_SIZE(dsmg600_devices));
+
+	pm_power_off = dsmg600_power_off;
+
+	if (request_irq(gpio_to_irq(DSMG600_RB_GPIO), &dsmg600_reset_handler,
+		IRQF_DISABLED | IRQF_TRIGGER_LOW,
+		"DSM-G600 reset button", NULL) < 0) {
+
+		printk(KERN_DEBUG "Reset Button IRQ %d not available\n",
+			gpio_to_irq(DSMG600_RB_GPIO));
+	}
+
+	/* The power button on the D-Link DSM-G600 is on GPIO 15, but
+	 * it cannot handle interrupts on that GPIO line.  So we'll
+	 * have to poll it with a kernel timer.
+	 */
+
+	/* Make sure that the power button GPIO is set up as an input */
+	gpio_line_config(DSMG600_PB_GPIO, IXP4XX_GPIO_IN);
+
+	/* Set the initial value for the power button IRQ handler */
+	power_button_countdown = PBUTTON_HOLDDOWN_COUNT;
+
+	mod_timer(&dsmg600_power_timer, jiffies + msecs_to_jiffies(500));
 }
 
 MACHINE_START(DSMG600, "D-Link DSM-G600 RevA")