---

yaml
---
r: 309582
b: refs/heads/master
c: ed5fb24
h: refs/heads/master
v: v3

[refs]

@@ -1,2 +1,2 @@
 ---
-refs/heads/master: 0c6be87161a6865a6f685a27c6a0404f9d1a0d5e
+refs/heads/master: ed5fb2471b7060767957fb964eb1aaec71533ab1

trunk/Documentation/ABI/testing/sysfs-bus-rbd

@@ -65,11 +65,11 @@ snap_*
 Entries under /sys/bus/rbd/devices/<dev-id>/snap_<snap-name>
 -------------------------------------------------------------
 
-snap_id
+id
 
 	The rados internal snapshot id assigned for this snapshot
 
-snap_size
+size
 
 	The size of the image when this snapshot was taken.
 

trunk/Documentation/SubmittingPatches

@@ -150,8 +150,7 @@ be able to justify all violations that remain in your patch.
 
 Look through the MAINTAINERS file and the source code, and determine
 if your change applies to a specific subsystem of the kernel, with
-an assigned maintainer.  If so, e-mail that person.  The script
-scripts/get_maintainer.pl can be very useful at this step.
+an assigned maintainer.  If so, e-mail that person.
 
 If no maintainer is listed, or the maintainer does not respond, send
 your patch to the primary Linux kernel developer's mailing list,

trunk/Documentation/arm/SPEAr/overview.txt

@@ -8,8 +8,9 @@ Introduction
   weblink : http://www.st.com/spear
 
   The ST Microelectronics SPEAr range of ARM9/CortexA9 System-on-Chip CPUs are
-  supported by the 'spear' platform of ARM Linux. Currently SPEAr1310,
-  SPEAr1340, SPEAr300, SPEAr310, SPEAr320 and SPEAr600 SOCs are supported.
+  supported by the 'spear' platform of ARM Linux. Currently SPEAr300,
+  SPEAr310, SPEAr320 and SPEAr600 SOCs are supported. Support for the SPEAr13XX
+  series is in progress.
 
   Hierarchy in SPEAr is as follows:
 
@@ -25,36 +26,33 @@ Introduction
 		- SPEAr600 (SOC)
 			- SPEAr600 Evaluation Board
 	- SPEAr13XX (13XX SOC series, based on ARM CORTEXA9)
-		- SPEAr1310 (SOC)
-			- SPEAr1310 Evaluation Board
-		- SPEAr1340 (SOC)
-			- SPEAr1340 Evaluation Board
+		- SPEAr1300 (SOC)
 
   Configuration
   -------------
 
   A generic configuration is provided for each machine, and can be used as the
   default by
-	make spear13xx_defconfig
-	make spear3xx_defconfig
-	make spear6xx_defconfig
+	make spear600_defconfig
+	make spear300_defconfig
+	make spear310_defconfig
+	make spear320_defconfig
 
   Layout
   ------
 
-  The common files for multiple machine families (SPEAr3xx, SPEAr6xx and
-  SPEAr13xx) are located in the platform code contained in arch/arm/plat-spear
+  The common files for multiple machine families (SPEAr3XX, SPEAr6XX and
+  SPEAr13XX) are located in the platform code contained in arch/arm/plat-spear
   with headers in plat/.
 
   Each machine series have a directory with name arch/arm/mach-spear followed by
   series name. Like mach-spear3xx, mach-spear6xx and mach-spear13xx.
 
-  Common file for machines of spear3xx family is mach-spear3xx/spear3xx.c, for
-  spear6xx is mach-spear6xx/spear6xx.c and for spear13xx family is
-  mach-spear13xx/spear13xx.c. mach-spear* also contain soc/machine specific
-  files, like spear1310.c, spear1340.c spear300.c, spear310.c, spear320.c and
-  spear600.c.  mach-spear* doesn't contains board specific files as they fully
-  support Flattened Device Tree.
+  Common file for machines of spear3xx family is mach-spear3xx/spear3xx.c and for
+  spear6xx is mach-spear6xx/spear6xx.c. mach-spear* also contain soc/machine
+  specific files, like spear300.c, spear310.c, spear320.c and spear600.c.
+  mach-spear* doesn't contains board specific files as they fully support
+  Flattened Device Tree.
 
 
   Document Author

trunk/Documentation/cgroups/memory.txt

@@ -184,14 +184,12 @@ behind this approach is that a cgroup that aggressively uses a shared
 page will eventually get charged for it (once it is uncharged from
 the cgroup that brought it in -- this will happen on memory pressure).
 
-But see section 8.2: when moving a task to another cgroup, its pages may
-be recharged to the new cgroup, if move_charge_at_immigrate has been chosen.
-
 Exception: If CONFIG_CGROUP_CGROUP_MEM_RES_CTLR_SWAP is not used.
 When you do swapoff and make swapped-out pages of shmem(tmpfs) to
 be backed into memory in force, charges for pages are accounted against the
 caller of swapoff rather than the users of shmem.
 
+
 2.4 Swap Extension (CONFIG_CGROUP_MEM_RES_CTLR_SWAP)
 
 Swap Extension allows you to record charge for swap. A swapped-in page is
@@ -376,15 +374,14 @@ cgroup might have some charge associated with it, even though all
 tasks have migrated away from it. (because we charge against pages, not
 against tasks.)
 
-We move the stats to root (if use_hierarchy==0) or parent (if
-use_hierarchy==1), and no change on the charge except uncharging
-from the child.
+Such charges are freed or moved to their parent. At moving, both of RSS
+and CACHES are moved to parent.
+rmdir() may return -EBUSY if freeing/moving fails. See 5.1 also.
 
 Charges recorded in swap information is not updated at removal of cgroup.
 Recorded information is discarded and a cgroup which uses swap (swapcache)
 will be charged as a new owner of it.
 
-About use_hierarchy, see Section 6.
 
 5. Misc. interfaces.
 
@@ -397,15 +394,13 @@ About use_hierarchy, see Section 6.
 
   Almost all pages tracked by this memory cgroup will be unmapped and freed.
   Some pages cannot be freed because they are locked or in-use. Such pages are
-  moved to parent(if use_hierarchy==1) or root (if use_hierarchy==0) and this
-  cgroup will be empty.
+  moved to parent and this cgroup will be empty. This may return -EBUSY if
+  VM is too busy to free/move all pages immediately.
 
   Typical use case of this interface is that calling this before rmdir().
   Because rmdir() moves all pages to parent, some out-of-use page caches can be
   moved to the parent. If you want to avoid that, force_empty will be useful.
 
-  About use_hierarchy, see Section 6.
-
 5.2 stat file
 
 memory.stat file includes following statistics
@@ -435,10 +430,17 @@ hierarchical_memory_limit - # of bytes of memory limit with regard to hierarchy
 hierarchical_memsw_limit - # of bytes of memory+swap limit with regard to
 			hierarchy under which memory cgroup is.
 
-total_<counter>		- # hierarchical version of <counter>, which in
-			addition to the cgroup's own value includes the
-			sum of all hierarchical children's values of
-			<counter>, i.e. total_cache
+total_cache		- sum of all children's "cache"
+total_rss		- sum of all children's "rss"
+total_mapped_file	- sum of all children's "cache"
+total_pgpgin		- sum of all children's "pgpgin"
+total_pgpgout		- sum of all children's "pgpgout"
+total_swap		- sum of all children's "swap"
+total_inactive_anon	- sum of all children's "inactive_anon"
+total_active_anon	- sum of all children's "active_anon"
+total_inactive_file	- sum of all children's "inactive_file"
+total_active_file	- sum of all children's "active_file"
+total_unevictable	- sum of all children's "unevictable"
 
 # The following additional stats are dependent on CONFIG_DEBUG_VM.
 
@@ -620,7 +622,8 @@ memory cgroup.
   bit | what type of charges would be moved ?
  -----+------------------------------------------------------------------------
    0  | A charge of an anonymous page(or swap of it) used by the target task.
-      | You must enable Swap Extension(see 2.4) to enable move of swap charges.
+      | Those pages and swaps must be used only by the target task. You must
+      | enable Swap Extension(see 2.4) to enable move of swap charges.
  -----+------------------------------------------------------------------------
    1  | A charge of file pages(normal file, tmpfs file(e.g. ipc shared memory)
       | and swaps of tmpfs file) mmapped by the target task. Unlike the case of
@@ -633,6 +636,8 @@ memory cgroup.
 
 8.3 TODO
 
+- Implement madvise(2) to let users decide the vma to be moved or not to be
+  moved.
 - All of moving charge operations are done under cgroup_mutex. It's not good
   behavior to hold the mutex too long, so we may need some trick.
 

trunk/Documentation/cgroups/resource_counter.txt

@@ -92,14 +92,6 @@ to work with it.
 
 	The _locked routines imply that the res_counter->lock is taken.
 
- f. void res_counter_uncharge_until
-		(struct res_counter *rc, struct res_counter *top,
-		 unsinged long val)
-
-	Almost same as res_cunter_uncharge() but propagation of uncharge
-	stops when rc == top. This is useful when kill a res_coutner in
-	child cgroup.
-
  2.1 Other accounting routines
 
     There are more routines that may help you with common needs, like