---

yaml
---
r: 145623
b: refs/heads/master
c: b9e0353
h: refs/heads/master
i:
  145621: d8333dd
  145619: 43aef11
  145615: d3f5033
v: v3

[refs]

@@ -1,2 +1,2 @@
 ---
-refs/heads/master: b2e5d8588de0b5341eddad87dbe48d2185eaa3dd
+refs/heads/master: b9e0353fc85dab4ef5ebcef2bd09ebc4ce6d5a7b

trunk/arch/x86/kernel/acpi/boot.c

@@ -1162,22 +1162,9 @@ int mp_register_gsi(struct device *dev, u32 gsi, int triggering, int polarity)
 {
 	int ioapic;
 	int ioapic_pin;
-#ifdef CONFIG_X86_32
-#define MAX_GSI_NUM	4096
-#define IRQ_COMPRESSION_START	64
-
-	static int pci_irq = IRQ_COMPRESSION_START;
-	/*
-	 * Mapping between Global System Interrupts, which
-	 * represent all possible interrupts, and IRQs
-	 * assigned to actual devices.
-	 */
-	static int gsi_to_irq[MAX_GSI_NUM];
-#else
 
 	if (acpi_irq_model != ACPI_IRQ_MODEL_IOAPIC)
 		return gsi;
-#endif
 
 	/* Don't set up the ACPI SCI because it's already set up */
 	if (acpi_gbl_FADT.sci_interrupt == gsi)
@@ -1196,66 +1183,28 @@ int mp_register_gsi(struct device *dev, u32 gsi, int triggering, int polarity)
 		gsi = ioapic_renumber_irq(ioapic, gsi);
 #endif
 
-	/*
-	 * Avoid pin reprogramming.  PRTs typically include entries
-	 * with redundant pin->gsi mappings (but unique PCI devices);
-	 * we only program the IOAPIC on the first.
-	 */
 	if (ioapic_pin > MP_MAX_IOAPIC_PIN) {
 		printk(KERN_ERR "Invalid reference to IOAPIC pin "
 		       "%d-%d\n", mp_ioapic_routing[ioapic].apic_id,
 		       ioapic_pin);
 		return gsi;
 	}
+
+	/*
+	 * Avoid pin reprogramming.  PRTs typically include entries
+	 * with redundant pin->gsi mappings (but unique PCI devices);
+	 * we only program the IOAPIC on the first.
+	 */
 	if (test_bit(ioapic_pin, mp_ioapic_routing[ioapic].pin_programmed)) {
 		pr_debug("Pin %d-%d already programmed\n",
 			 mp_ioapic_routing[ioapic].apic_id, ioapic_pin);
-#ifdef CONFIG_X86_32
-		return (gsi < IRQ_COMPRESSION_START ? gsi : gsi_to_irq[gsi]);
-#else
 		return gsi;
-#endif
 	}
-
 	set_bit(ioapic_pin, mp_ioapic_routing[ioapic].pin_programmed);
-#ifdef CONFIG_X86_32
-	/*
-	 * For GSI >= 64, use IRQ compression
-	 */
-	if ((gsi >= IRQ_COMPRESSION_START)
-	    && (triggering == ACPI_LEVEL_SENSITIVE)) {
-		/*
-		 * For PCI devices assign IRQs in order, avoiding gaps
-		 * due to unused I/O APIC pins.
-		 */
-		int irq = gsi;
-		if (gsi < MAX_GSI_NUM) {
-			/*
-			 * Retain the VIA chipset work-around (gsi > 15), but
-			 * avoid a problem where the 8254 timer (IRQ0) is setup
-			 * via an override (so it's not on pin 0 of the ioapic),
-			 * and at the same time, the pin 0 interrupt is a PCI
-			 * type.  The gsi > 15 test could cause these two pins
-			 * to be shared as IRQ0, and they are not shareable.
-			 * So test for this condition, and if necessary, avoid
-			 * the pin collision.
-			 */
-			gsi = pci_irq++;
-			/*
-			 * Don't assign IRQ used by ACPI SCI
-			 */
-			if (gsi == acpi_gbl_FADT.sci_interrupt)
-				gsi = pci_irq++;
-			gsi_to_irq[irq] = gsi;
-		} else {
-			printk(KERN_ERR "GSI %u is too high\n", gsi);
-			return gsi;
-		}
-	}
-#endif
 	io_apic_set_pci_routing(dev, ioapic, ioapic_pin, gsi,
 				triggering == ACPI_EDGE_SENSITIVE ? 0 : 1,
 				polarity == ACPI_ACTIVE_HIGH ? 0 : 1);
+
 	return gsi;
 }