---

yaml
---
r: 63554
b: refs/heads/master
c: 878701d
h: refs/heads/master
v: v3

[refs]

@@ -1,2 +1,2 @@
 ---
-refs/heads/master: 3fcece66911c9d485c1e2050ba033fde607b5130
+refs/heads/master: 878701db07db3f0b59f14f0c525b681e4ca81551

trunk/arch/frv/mb93090-mb00/pci-vdk.c

@@ -400,7 +400,8 @@ int __init pcibios_init(void)
 	__reg_MB86943_pci_sl_mem_base	= __region_CS2 + 0x08000000;
 	mb();
 
-	*(volatile unsigned long *)(__region_CS2+0x01300014) == 1;
+	/* enable PCI arbitration */
+	__reg_MB86943_pci_arbiter	= MB86943_PCIARB_EN;
 
 	ioport_resource.start	= (__reg_MB86943_sl_pci_io_base << 9) & 0xfffffc00;
 	ioport_resource.end	= (__reg_MB86943_sl_pci_io_range << 9) | 0x3ff;

trunk/drivers/ata/ata_piix.c

@@ -890,37 +890,46 @@ static void ich_set_dmamode (struct ata_port *ap, struct ata_device *adev)
 }
 
 #ifdef CONFIG_PM
-static struct dmi_system_id piix_broken_suspend_dmi_table[] = {
-	{
-		.ident = "TECRA M5",
-		.matches = {
-			DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
-			DMI_MATCH(DMI_PRODUCT_NAME, "TECRA M5"),
-		},
-	},
-	{
-		.ident = "Satellite U200",
-		.matches = {
-			DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
-			DMI_MATCH(DMI_PRODUCT_NAME, "Satellite U200"),
+static int piix_broken_suspend(void)
+{
+	static struct dmi_system_id sysids[] = {
+		{
+			.ident = "TECRA M5",
+			.matches = {
+				DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
+				DMI_MATCH(DMI_PRODUCT_NAME, "TECRA M5"),
+			},
 		},
-	},
-	{
-		.ident = "Satellite U205",
-		.matches = {
-			DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
-			DMI_MATCH(DMI_PRODUCT_NAME, "Satellite U205"),
+		{
+			.ident = "Satellite U205",
+			.matches = {
+				DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
+				DMI_MATCH(DMI_PRODUCT_NAME, "Satellite U205"),
+			},
 		},
-	},
-	{
-		.ident = "Portege M500",
-		.matches = {
-			DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
-			DMI_MATCH(DMI_PRODUCT_NAME, "PORTEGE M500"),
+		{
+			.ident = "Portege M500",
+			.matches = {
+				DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
+				DMI_MATCH(DMI_PRODUCT_NAME, "PORTEGE M500"),
+			},
 		},
-	},
-	{ }
-};
+		{ }
+	};
+	static const char *oemstrs[] = {
+		"Tecra M3,",
+	};
+	int i;
+
+	if (dmi_check_system(sysids))
+		return 1;
+
+	for (i = 0; i < ARRAY_SIZE(oemstrs); i++)
+		if (dmi_find_device(DMI_DEV_TYPE_OEM_STRING, oemstrs[i], NULL))
+			return 1;
+
+	return 0;
+}
 
 static int piix_pci_device_suspend(struct pci_dev *pdev, pm_message_t mesg)
 {
@@ -937,8 +946,7 @@ static int piix_pci_device_suspend(struct pci_dev *pdev, pm_message_t mesg)
 	 * cycles and power trying to do something to the sleeping
 	 * beauty.
 	 */
-	if (dmi_check_system(piix_broken_suspend_dmi_table) &&
-	    mesg.event == PM_EVENT_SUSPEND) {
+	if (piix_broken_suspend() && mesg.event == PM_EVENT_SUSPEND) {
 		pci_save_state(pdev);
 
 		/* mark its power state as "unknown", since we don't
@@ -973,10 +981,10 @@ static int piix_pci_device_resume(struct pci_dev *pdev)
 		pci_restore_state(pdev);
 
 		/* PCI device wasn't disabled during suspend.  Use
-		 * __pci_reenable_device() to avoid affecting the
-		 * enable count.
+		 * pci_reenable_device() to avoid affecting the enable
+		 * count.
 		 */
-		rc = __pci_reenable_device(pdev);
+		rc = pci_reenable_device(pdev);
 		if (rc)
 			dev_printk(KERN_ERR, &pdev->dev, "failed to enable "
 				   "device after resume (%d)\n", rc);

trunk/drivers/ata/libata-core.c

@@ -3788,6 +3788,7 @@ static const struct ata_blacklist_entry ata_device_blacklist [] = {
 	{ "WDC WD740ADFD-00NLR1", NULL,		ATA_HORKAGE_NONCQ, },
 	{ "FUJITSU MHV2080BH",	"00840028",	ATA_HORKAGE_NONCQ, },
 	{ "ST9160821AS",	"3.CLF",	ATA_HORKAGE_NONCQ, },
+	{ "SAMSUNG HD401LJ",	"ZZ100-15",	ATA_HORKAGE_NONCQ, },
 
 	/* Devices with NCQ limits */
 

trunk/drivers/ata/libata-sff.c

@@ -573,6 +573,10 @@ int ata_pci_init_bmdma(struct ata_host *host)
 	struct pci_dev *pdev = to_pci_dev(gdev);
 	int i, rc;
 
+	/* No BAR4 allocation: No DMA */
+	if (pci_resource_start(pdev, 4) == 0)
+		return 0;
+
 	/* TODO: If we get no DMA mask we should fall back to PIO */
 	rc = pci_set_dma_mask(pdev, ATA_DMA_MASK);
 	if (rc)

trunk/drivers/ata/pata_cmd64x.c

@@ -31,7 +31,7 @@
 #include <linux/libata.h>
 
 #define DRV_NAME "pata_cmd64x"
-#define DRV_VERSION "0.2.3"
+#define DRV_VERSION "0.2.4"
 
 /*
  * CMD64x specific registers definition.
@@ -397,7 +397,7 @@ static int cmd64x_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
 			.flags = ATA_FLAG_SLAVE_POSS,
 			.pio_mask = 0x1f,
 			.mwdma_mask = 0x07,
-			.udma_mask = ATA_UDMA1,
+			.udma_mask = ATA_UDMA2,
 			.port_ops = &cmd64x_port_ops
 		},
 		{	/* CMD 646 rev 1  */
@@ -412,15 +412,15 @@ static int cmd64x_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
 			.flags = ATA_FLAG_SLAVE_POSS,
 			.pio_mask = 0x1f,
 			.mwdma_mask = 0x07,
-			.udma_mask = ATA_UDMA2,
+			.udma_mask = ATA_UDMA4,
 			.port_ops = &cmd648_port_ops
 		},
 		{	/* CMD 649 */
 			.sht = &cmd64x_sht,
 			.flags = ATA_FLAG_SLAVE_POSS,
 			.pio_mask = 0x1f,
 			.mwdma_mask = 0x07,
-			.udma_mask = ATA_UDMA3,
+			.udma_mask = ATA_UDMA5,
 			.port_ops = &cmd648_port_ops
 		}
 	};

trunk/drivers/ata/pata_sis.c

@@ -2,6 +2,7 @@
  *    pata_sis.c - SiS ATA driver
  *
  *	(C) 2005 Red Hat <alan@redhat.com>
+ *	(C) 2007 Bartlomiej Zolnierkiewicz
  *
  *    Based upon linux/drivers/ide/pci/sis5513.c
  * Copyright (C) 1999-2000	Andre Hedrick <andre@linux-ide.org>
@@ -35,7 +36,7 @@
 #include "sis.h"
 
 #define DRV_NAME	"pata_sis"
-#define DRV_VERSION	"0.5.1"
+#define DRV_VERSION	"0.5.2"
 
 struct sis_chipset {
 	u16 device;				/* PCI host ID */
@@ -237,7 +238,7 @@ static void sis_old_set_piomode (struct ata_port *ap, struct ata_device *adev)
 }
 
 /**
- *	sis_100_set_pioode - Initialize host controller PATA PIO timings
+ *	sis_100_set_piomode - Initialize host controller PATA PIO timings
  *	@ap: Port whose timings we are configuring
  *	@adev: Device we are configuring for.
  *
@@ -262,7 +263,7 @@ static void sis_100_set_piomode (struct ata_port *ap, struct ata_device *adev)
 }
 
 /**
- *	sis_133_set_pioode - Initialize host controller PATA PIO timings
+ *	sis_133_set_piomode - Initialize host controller PATA PIO timings
  *	@ap: Port whose timings we are configuring
  *	@adev: Device we are configuring for.
  *
@@ -334,23 +335,23 @@ static void sis_old_set_dmamode (struct ata_port *ap, struct ata_device *adev)
 	int drive_pci = sis_old_port_base(adev);
 	u16 timing;
 
-	const u16 mwdma_bits[] = { 0x707, 0x202, 0x202 };
+	const u16 mwdma_bits[] = { 0x008, 0x302, 0x301 };
 	const u16 udma_bits[]  = { 0xE000, 0xC000, 0xA000 };
 
 	pci_read_config_word(pdev, drive_pci, &timing);
 
 	if (adev->dma_mode < XFER_UDMA_0) {
 		/* bits 3-0 hold recovery timing bits 8-10 active timing and
 		   the higer bits are dependant on the device */
-		timing &= ~ 0x870F;
+		timing &= ~0x870F;
 		timing |= mwdma_bits[speed];
-		pci_write_config_word(pdev, drive_pci, timing);
 	} else {
 		/* Bit 15 is UDMA on/off, bit 13-14 are cycle time */
 		speed = adev->dma_mode - XFER_UDMA_0;
 		timing &= ~0x6000;
 		timing |= udma_bits[speed];
 	}
+	pci_write_config_word(pdev, drive_pci, timing);
 }
 
 /**
@@ -373,7 +374,7 @@ static void sis_66_set_dmamode (struct ata_port *ap, struct ata_device *adev)
 	int drive_pci = sis_old_port_base(adev);
 	u16 timing;
 
-	const u16 mwdma_bits[] = { 0x707, 0x202, 0x202 };
+	const u16 mwdma_bits[] = { 0x008, 0x302, 0x301 };
 	const u16 udma_bits[]  = { 0xF000, 0xD000, 0xB000, 0xA000, 0x9000};
 
 	pci_read_config_word(pdev, drive_pci, &timing);
@@ -432,8 +433,7 @@ static void sis_100_set_dmamode (struct ata_port *ap, struct ata_device *adev)
  *	@adev: Device to program
  *
  *	Set UDMA/MWDMA mode for device, in host controller PCI config space.
- *	Handles early SiS 961 bridges. Supports MWDMA as well unlike
- *	the old ide/pci driver.
+ *	Handles early SiS 961 bridges.
  *
  *	LOCKING:
  *	None (inherited from caller).
@@ -467,8 +467,6 @@ static void sis_133_early_set_dmamode (struct ata_port *ap, struct ata_device *a
  *	@adev: Device to program
  *
  *	Set UDMA/MWDMA mode for device, in host controller PCI config space.
- *	Handles early SiS 961 bridges. Supports MWDMA as well unlike
- *	the old ide/pci driver.
  *
  *	LOCKING:
  *	None (inherited from caller).

trunk/drivers/pci/pci-driver.c

@@ -310,7 +310,7 @@ static int pci_default_resume(struct pci_dev *pci_dev)
 	/* restore the PCI config space */
 	pci_restore_state(pci_dev);
 	/* if the device was enabled before suspend, reenable */
-	retval = __pci_reenable_device(pci_dev);
+	retval = pci_reenable_device(pci_dev);
 	/* if the device was busmaster before the suspend, make it busmaster again */
 	if (pci_dev->is_busmaster)
 		pci_set_master(pci_dev);

trunk/drivers/pci/pci.c

@@ -695,14 +695,13 @@ static int do_pci_enable_device(struct pci_dev *dev, int bars)
 }
 
 /**
- * __pci_reenable_device - Resume abandoned device
+ * pci_reenable_device - Resume abandoned device
  * @dev: PCI device to be resumed
  *
  *  Note this function is a backend of pci_default_resume and is not supposed
  *  to be called by normal code, write proper resume handler and use it instead.
  */
-int
-__pci_reenable_device(struct pci_dev *dev)
+int pci_reenable_device(struct pci_dev *dev)
 {
 	if (atomic_read(&dev->enable_cnt))
 		return do_pci_enable_device(dev, (1 << PCI_NUM_RESOURCES) - 1);
@@ -1604,7 +1603,7 @@ early_param("pci", pci_setup);
 device_initcall(pci_init);
 
 EXPORT_SYMBOL_GPL(pci_restore_bars);
-EXPORT_SYMBOL(__pci_reenable_device);
+EXPORT_SYMBOL(pci_reenable_device);
 EXPORT_SYMBOL(pci_enable_device_bars);
 EXPORT_SYMBOL(pci_enable_device);
 EXPORT_SYMBOL(pcim_enable_device);

trunk/include/asm-avr32/bug.h

@@ -57,7 +57,7 @@
 
 #define WARN_ON(condition)							\
 	({								\
-		typeof(condition) __ret_warn_on = (condition);		\
+		int __ret_warn_on = !!(condition);			\
 		if (unlikely(__ret_warn_on))				\
 			_BUG_OR_WARN(BUGFLAG_WARNING);			\
 		unlikely(__ret_warn_on);				\

trunk/include/asm-frv/mb86943a.h

@@ -36,4 +36,7 @@
 #define __reg_MB86943_pci_sl_io_base	*(volatile uint32_t *) (__region_CS1 + 0x70)
 #define __reg_MB86943_pci_sl_mem_base	*(volatile uint32_t *) (__region_CS1 + 0x78)
 
+#define __reg_MB86943_pci_arbiter	*(volatile uint32_t *) (__region_CS2 + 0x01300014)
+#define MB86943_PCIARB_EN		0x00000001
+
 #endif /* _ASM_MB86943A_H */

trunk/include/asm-parisc/bug.h

@@ -74,7 +74,7 @@
 
 
 #define WARN_ON(x) ({						\
-	typeof(x) __ret_warn_on = (x);				\
+	int __ret_warn_on = !!(x);				\
 	if (__builtin_constant_p(__ret_warn_on)) {		\
 		if (__ret_warn_on)				\
 			__WARN();				\

trunk/include/asm-s390/bug.h

@@ -50,7 +50,7 @@
 #define BUG()	__EMIT_BUG(0)
 
 #define WARN_ON(x) ({					\
-	typeof(x) __ret_warn_on = (x);			\
+	int __ret_warn_on = !!(x);			\
 	if (__builtin_constant_p(__ret_warn_on)) {	\
 		if (__ret_warn_on)			\
 			__EMIT_BUG(BUGFLAG_WARNING);	\

trunk/include/asm-sh/bug.h

@@ -61,7 +61,7 @@ do {							\
 } while (0)
 
 #define WARN_ON(x) ({						\
-	typeof(x) __ret_warn_on = (x);				\
+	int __ret_warn_on = !!(x);				\
 	if (__builtin_constant_p(__ret_warn_on)) {		\
 		if (__ret_warn_on)				\
 			__WARN();				\

trunk/include/linux/pci.h

@@ -534,7 +534,7 @@ static inline int pci_write_config_dword(struct pci_dev *dev, int where, u32 val
 
 int __must_check pci_enable_device(struct pci_dev *dev);
 int __must_check pci_enable_device_bars(struct pci_dev *dev, int mask);
-int __must_check __pci_reenable_device(struct pci_dev *);
+int __must_check pci_reenable_device(struct pci_dev *);
 int __must_check pcim_enable_device(struct pci_dev *pdev);
 void pcim_pin_device(struct pci_dev *pdev);
 

trunk/kernel/irq/resend.c

@@ -62,6 +62,15 @@ void check_irq_resend(struct irq_desc *desc, unsigned int irq)
 	 */
 	desc->chip->enable(irq);
 
+	/*
+	 * Temporary hack to figure out more about the problem, which
+	 * is causing the ancient network cards to die.
+	 */
+	if (desc->handle_irq != handle_edge_irq) {
+		WARN_ON_ONCE(1);
+		return;
+	}
+
 	if ((status & (IRQ_PENDING | IRQ_REPLAY)) == IRQ_PENDING) {
 		desc->status = (status & ~IRQ_PENDING) | IRQ_REPLAY;