---

yaml
---
r: 178758
b: refs/heads/master
c: 70670e4
h: refs/heads/master
v: v3

[refs]

@@ -1,2 +1,2 @@
 ---
-refs/heads/master: b9bf770e0d4cc95e43ab04c66e705ba72a9bded3
+refs/heads/master: 70670e4b8d75291f7d03771e26f7f7794d2d3eba

trunk/Documentation/ABI/testing/sysfs-bus-usb

@@ -21,25 +21,27 @@ Contact:	Alan Stern <stern@rowland.harvard.edu>
 Description:
 		Each USB device directory will contain a file named
 		power/level.  This file holds a power-level setting for
-		the device, one of "on", "auto", or "suspend".
+		the device, either "on" or "auto".
 
 		"on" means that the device is not allowed to autosuspend,
 		although normal suspends for system sleep will still
 		be honored.  "auto" means the device will autosuspend
 		and autoresume in the usual manner, according to the
-		capabilities of its driver.  "suspend" means the device
-		is forced into a suspended state and it will not autoresume
-		in response to I/O requests.  However remote-wakeup requests
-		from the device may still be enabled (the remote-wakeup
-		setting is controlled separately by the power/wakeup
-		attribute).
+		capabilities of its driver.
 
 		During normal use, devices should be left in the "auto"
-		level.  The other levels are meant for administrative uses.
+		level.  The "on" level is meant for administrative uses.
 		If you want to suspend a device immediately but leave it
 		free to wake up in response to I/O requests, you should
 		write "0" to power/autosuspend.
 
+		Device not capable of proper suspend and resume should be
+		left in the "on" level.  Although the USB spec requires
+		devices to support suspend/resume, many of them do not.
+		In fact so many don't that by default, the USB core
+		initializes all non-hub devices in the "on" level.  Some
+		drivers may change this setting when they are bound.
+
 What:		/sys/bus/usb/devices/.../power/persist
 Date:		May 2007
 KernelVersion:	2.6.23

trunk/Documentation/DocBook/mtdnand.tmpl

@@ -174,15 +174,15 @@
 		</para>
 		<programlisting>
 static struct mtd_info *board_mtd;
-static unsigned long baseaddr;
+static void __iomem *baseaddr;
 		</programlisting>
 		<para>
 			Static example
 		</para>
 		<programlisting>
 static struct mtd_info board_mtd;
 static struct nand_chip board_chip;
-static unsigned long baseaddr;
+static void __iomem *baseaddr;
 		</programlisting>
 	</sect1>
 	<sect1 id="Partition_defines">
@@ -283,8 +283,8 @@ int __init board_init (void)
 	}
 
 	/* map physical address */
-	baseaddr = (unsigned long)ioremap(CHIP_PHYSICAL_ADDRESS, 1024);
-	if(!baseaddr){
+	baseaddr = ioremap(CHIP_PHYSICAL_ADDRESS, 1024);
+	if (!baseaddr) {
 		printk("Ioremap to access NAND chip failed\n");
 		err = -EIO;
 		goto out_mtd;
@@ -316,7 +316,7 @@ int __init board_init (void)
 	goto out;
 
 out_ior:
-	iounmap((void *)baseaddr);
+	iounmap(baseaddr);
 out_mtd:
 	kfree (board_mtd);
 out:
@@ -341,7 +341,7 @@ static void __exit board_cleanup (void)
 	nand_release (board_mtd);
 
 	/* unmap physical address */
-	iounmap((void *)baseaddr);
+	iounmap(baseaddr);
 
 	/* Free the MTD device structure */
 	kfree (board_mtd);

trunk/Documentation/IO-mapping.txt

@@ -157,7 +157,7 @@ For such memory, you can do things like
 	 * access only the 640k-1MB area, so anything else
 	 * has to be remapped.
 	 */
-	char * baseptr = ioremap(0xFC000000, 1024*1024);
+	void __iomem *baseptr = ioremap(0xFC000000, 1024*1024);
 
 	/* write a 'A' to the offset 10 of the area */
 	writeb('A',baseptr+10);

trunk/Documentation/block/00-INDEX

@@ -1,7 +1,5 @@
 00-INDEX
 	- This file
-as-iosched.txt
-	- Anticipatory IO scheduler
 barrier.txt
 	- I/O Barriers
 biodoc.txt

trunk/Documentation/block/biodoc.txt

@@ -186,7 +186,7 @@ a virtual address mapping (unlike the earlier scheme of virtual address
 do not have a corresponding kernel virtual address space mapping) and
 low-memory pages.
 
-Note: Please refer to Documentation/DMA-mapping.txt for a discussion
+Note: Please refer to Documentation/PCI/PCI-DMA-mapping.txt for a discussion
 on PCI high mem DMA aspects and mapping of scatter gather lists, and support
 for 64 bit PCI.
 

trunk/Documentation/driver-model/driver.txt

@@ -226,5 +226,5 @@ struct driver_attribute driver_attr_debug;
 This can then be used to add and remove the attribute from the
 driver's directory using:
 
-int driver_create_file(struct device_driver *, struct driver_attribute *);
-void driver_remove_file(struct device_driver *, struct driver_attribute *);
+int driver_create_file(struct device_driver *, const struct driver_attribute *);
+void driver_remove_file(struct device_driver *, const struct driver_attribute *);

trunk/Documentation/filesystems/ext4.txt

@@ -196,7 +196,7 @@ nobarrier		This also requires an IO stack which can support
 			also be used to enable or disable barriers, for
 			consistency with other ext4 mount options.
 
-inode_readahead=n	This tuning parameter controls the maximum
+inode_readahead_blks=n	This tuning parameter controls the maximum
 			number of inode table blocks that ext4's inode
 			table readahead algorithm will pre-read into
 			the buffer cache.  The default value is 32 blocks.

trunk/Documentation/filesystems/sysfs.txt

@@ -91,8 +91,8 @@ struct device_attribute {
 			 const char *buf, size_t count);
 };
 
-int device_create_file(struct device *, struct device_attribute *);
-void device_remove_file(struct device *, struct device_attribute *);
+int device_create_file(struct device *, const struct device_attribute *);
+void device_remove_file(struct device *, const struct device_attribute *);
 
 It also defines this helper for defining device attributes: 
 
@@ -316,8 +316,8 @@ DEVICE_ATTR(_name, _mode, _show, _store);
 
 Creation/Removal:
 
-int device_create_file(struct device *device, struct device_attribute * attr);
-void device_remove_file(struct device * dev, struct device_attribute * attr);
+int device_create_file(struct device *dev, const struct device_attribute * attr);
+void device_remove_file(struct device *dev, const struct device_attribute * attr);
 
 
 - bus drivers (include/linux/device.h)
@@ -358,7 +358,7 @@ DRIVER_ATTR(_name, _mode, _show, _store)
 
 Creation/Removal:
 
-int driver_create_file(struct device_driver *, struct driver_attribute *);
-void driver_remove_file(struct device_driver *, struct driver_attribute *);
+int driver_create_file(struct device_driver *, const struct driver_attribute *);
+void driver_remove_file(struct device_driver *, const struct driver_attribute *);
 
 

trunk/Documentation/kernel-parameters.txt

@@ -240,7 +240,7 @@ and is between 256 and 4096 characters. It is defined in the file
 
 	acpi_sleep=	[HW,ACPI] Sleep options
 			Format: { s3_bios, s3_mode, s3_beep, s4_nohwsig,
-				  old_ordering, s4_nonvs }
+				  old_ordering, s4_nonvs, sci_force_enable }
 			See Documentation/power/video.txt for information on
 			s3_bios and s3_mode.
 			s3_beep is for debugging; it makes the PC's speaker beep
@@ -253,6 +253,9 @@ and is between 256 and 4096 characters. It is defined in the file
 			of _PTS is used by default).
 			s4_nonvs prevents the kernel from saving/restoring the
 			ACPI NVS memory during hibernation.
+			sci_force_enable causes the kernel to set SCI_EN directly
+			on resume from S1/S3 (which is against the ACPI spec,
+			but some broken systems don't work without it).
 
 	acpi_use_timer_override [HW,ACPI]
 			Use timer override. For some broken Nvidia NF5 boards

trunk/Documentation/kvm/api.txt

@@ -685,7 +685,7 @@ struct kvm_vcpu_events {
 		__u8 pad;
 	} nmi;
 	__u32 sipi_vector;
-	__u32 flags;   /* must be zero */
+	__u32 flags;
 };
 
 4.30 KVM_SET_VCPU_EVENTS
@@ -701,6 +701,14 @@ vcpu.
 
 See KVM_GET_VCPU_EVENTS for the data structure.
 
+Fields that may be modified asynchronously by running VCPUs can be excluded
+from the update. These fields are nmi.pending and sipi_vector. Keep the
+corresponding bits in the flags field cleared to suppress overwriting the
+current in-kernel state. The bits are:
+
+KVM_VCPUEVENT_VALID_NMI_PENDING - transfer nmi.pending to the kernel
+KVM_VCPUEVENT_VALID_SIPI_VECTOR - transfer sipi_vector
+
 
 5. The kvm_run structure