---

yaml
---
r: 138722
b: refs/heads/master
c: 9fa7266
h: refs/heads/master
v: v3

[refs]

@@ -1,2 +1,2 @@
 ---
-refs/heads/master: 7a81d9a7da03d2f27840d659f97ef140d032f609
+refs/heads/master: 9fa7266c2f0cdfcb09eacba2d3624bec7df78641

trunk/Documentation/RCU/checklist.txt

@@ -298,3 +298,15 @@ over a rather long period of time, but improvements are always welcome!
 
 	Note that, rcu_assign_pointer() and rcu_dereference() relate to
 	SRCU just as they do to other forms of RCU.
+
+15.	The whole point of call_rcu(), synchronize_rcu(), and friends
+	is to wait until all pre-existing readers have finished before
+	carrying out some otherwise-destructive operation.  It is
+	therefore critically important to -first- remove any path
+	that readers can follow that could be affected by the
+	destructive operation, and -only- -then- invoke call_rcu(),
+	synchronize_rcu(), or friends.
+
+	Because these primitives only wait for pre-existing readers,
+	it is the caller's responsibility to guarantee safety to
+	any subsequent readers.

trunk/Documentation/feature-removal-schedule.txt

@@ -335,3 +335,12 @@ Why:	In 2.6.18 the Secmark concept was introduced to replace the "compat_net"
 	Secmark, it is time to deprecate the older mechanism and start the
 	process of removing the old code.
 Who:	Paul Moore <paul.moore@hp.com>
+---------------------------
+
+What:	sysfs ui for changing p4-clockmod parameters
+When:	September 2009
+Why:	See commits 129f8ae9b1b5be94517da76009ea956e89104ce8 and
+	e088e4c9cdb618675874becb91b2fd581ee707e6.
+	Removal is subject to fixing any remaining bugs in ACPI which may
+	cause the thermal throttling not to happen at the right time.
+Who:	Dave Jones <davej@redhat.com>, Matthew Garrett <mjg@redhat.com>

trunk/Documentation/filesystems/squashfs.txt

@@ -22,7 +22,7 @@ Squashfs filesystem features versus Cramfs:
 
 				Squashfs		Cramfs
 
-Max filesystem size:		2^64			16 MiB
+Max filesystem size:		2^64			256 MiB
 Max file size:			~ 2 TiB			16 MiB
 Max files:			unlimited		unlimited
 Max directories:		unlimited		unlimited

trunk/Documentation/networking/ipv6.txt

@@ -0,0 +1,35 @@
+
+Options for the ipv6 module are supplied as parameters at load time.
+
+Module options may be given as command line arguments to the insmod
+or modprobe command, but are usually specified in either the
+/etc/modules.conf or /etc/modprobe.conf configuration file, or in a
+distro-specific configuration file.
+
+The available ipv6 module parameters are listed below.  If a parameter
+is not specified the default value is used.
+
+The parameters are as follows:
+
+disable
+
+	Specifies whether to load the IPv6 module, but disable all
+	its functionality.  This might be used when another module
+	has a dependency on the IPv6 module being loaded, but no
+	IPv6 addresses or operations are desired.
+
+	The possible values and their effects are:
+
+	0
+		IPv6 is enabled.
+
+		This is the default value.
+
+	1
+		IPv6 is disabled.
+
+		No IPv6 addresses will be added to interfaces, and
+		it will not be possible to open an IPv6 socket.
+
+		A reboot is required to enable IPv6.
+

trunk/arch/arm/mach-at91/at91sam9263_devices.c

@@ -347,6 +347,111 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data)
 void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {}
 #endif
 
+/* --------------------------------------------------------------------
+ *  Compact Flash (PCMCIA or IDE)
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_AT91_CF) || defined(CONFIG_AT91_CF_MODULE) || \
+    defined(CONFIG_BLK_DEV_IDE_AT91) || defined(CONFIG_BLK_DEV_IDE_AT91_MODULE)
+
+static struct at91_cf_data cf0_data;
+
+static struct resource cf0_resources[] = {
+	[0] = {
+		.start	= AT91_CHIPSELECT_4,
+		.end	= AT91_CHIPSELECT_4 + SZ_256M - 1,
+		.flags	= IORESOURCE_MEM | IORESOURCE_MEM_8AND16BIT,
+	}
+};
+
+static struct platform_device cf0_device = {
+	.id		= 0,
+	.dev		= {
+				.platform_data	= &cf0_data,
+	},
+	.resource	= cf0_resources,
+	.num_resources	= ARRAY_SIZE(cf0_resources),
+};
+
+static struct at91_cf_data cf1_data;
+
+static struct resource cf1_resources[] = {
+	[0] = {
+		.start	= AT91_CHIPSELECT_5,
+		.end	= AT91_CHIPSELECT_5 + SZ_256M - 1,
+		.flags	= IORESOURCE_MEM | IORESOURCE_MEM_8AND16BIT,
+	}
+};
+
+static struct platform_device cf1_device = {
+	.id		= 1,
+	.dev		= {
+				.platform_data	= &cf1_data,
+	},
+	.resource	= cf1_resources,
+	.num_resources	= ARRAY_SIZE(cf1_resources),
+};
+
+void __init at91_add_device_cf(struct at91_cf_data *data)
+{
+	unsigned long ebi0_csa;
+	struct platform_device *pdev;
+
+	if (!data)
+		return;
+
+	/*
+	 * assign CS4 or CS5 to SMC with Compact Flash logic support,
+	 * we assume SMC timings are configured by board code,
+	 * except True IDE where timings are controlled by driver
+	 */
+	ebi0_csa = at91_sys_read(AT91_MATRIX_EBI0CSA);
+	switch (data->chipselect) {
+	case 4:
+		at91_set_A_periph(AT91_PIN_PD6, 0);  /* EBI0_NCS4/CFCS0 */
+		ebi0_csa |= AT91_MATRIX_EBI0_CS4A_SMC_CF1;
+		cf0_data = *data;
+		pdev = &cf0_device;
+		break;
+	case 5:
+		at91_set_A_periph(AT91_PIN_PD7, 0);  /* EBI0_NCS5/CFCS1 */
+		ebi0_csa |= AT91_MATRIX_EBI0_CS5A_SMC_CF2;
+		cf1_data = *data;
+		pdev = &cf1_device;
+		break;
+	default:
+		printk(KERN_ERR "AT91 CF: bad chip-select requested (%u)\n",
+		       data->chipselect);
+		return;
+	}
+	at91_sys_write(AT91_MATRIX_EBI0CSA, ebi0_csa);
+
+	if (data->det_pin) {
+		at91_set_gpio_input(data->det_pin, 1);
+		at91_set_deglitch(data->det_pin, 1);
+	}
+
+	if (data->irq_pin) {
+		at91_set_gpio_input(data->irq_pin, 1);
+		at91_set_deglitch(data->irq_pin, 1);
+	}
+
+	if (data->vcc_pin)
+		/* initially off */
+		at91_set_gpio_output(data->vcc_pin, 0);
+
+	/* enable EBI controlled pins */
+	at91_set_A_periph(AT91_PIN_PD5, 1);  /* NWAIT */
+	at91_set_A_periph(AT91_PIN_PD8, 0);  /* CFCE1 */
+	at91_set_A_periph(AT91_PIN_PD9, 0);  /* CFCE2 */
+	at91_set_A_periph(AT91_PIN_PD14, 0); /* CFNRW */
+
+	pdev->name = (data->flags & AT91_CF_TRUE_IDE) ? "at91_ide" : "at91_cf";
+	platform_device_register(pdev);
+}
+#else
+void __init at91_add_device_cf(struct at91_cf_data *data) {}
+#endif
 
 /* --------------------------------------------------------------------
  *  NAND / SmartMedia

trunk/arch/arm/mach-at91/include/mach/board.h

@@ -56,6 +56,9 @@ struct at91_cf_data {
 	u8	vcc_pin;		/* power switching */
 	u8	rst_pin;		/* card reset */
 	u8	chipselect;		/* EBI Chip Select number */
+	u8	flags;
+#define AT91_CF_TRUE_IDE	0x01
+#define AT91_IDE_SWAP_A0_A2	0x02
 };
 extern void __init at91_add_device_cf(struct at91_cf_data *data);
 

trunk/arch/arm/mach-omap2/board-ldp.c

@@ -81,7 +81,7 @@ static inline void __init ldp_init_smc911x(void)
 	}
 
 	ldp_smc911x_resources[0].start = cs_mem_base + 0x0;
-	ldp_smc911x_resources[0].end   = cs_mem_base + 0xf;
+	ldp_smc911x_resources[0].end   = cs_mem_base + 0xff;
 	udelay(100);
 
 	eth_gpio = LDP_SMC911X_GPIO;

trunk/arch/blackfin/Kconfig

@@ -1129,6 +1129,7 @@ endchoice
 
 config PM_WAKEUP_BY_GPIO
 	bool "Allow Wakeup from Standby by GPIO"
+	depends on PM && !BF54x
 
 config PM_WAKEUP_GPIO_NUMBER
 	int "GPIO number"
@@ -1168,6 +1169,12 @@ config PM_BFIN_WAKE_GP
 	default n
 	help
 	  Enable General-Purpose Wake-Up (Voltage Regulator Power-Up)
+	  (all processors, except ADSP-BF549). This option sets
+	  the general-purpose wake-up enable (GPWE) control bit to enable
+	  wake-up upon detection of an active low signal on the /GPW (PH7) pin.
+	  On ADSP-BF549 this option enables the the same functionality on the
+	  /MRXON pin also PH7.
+
 endmenu
 
 menu "CPU Frequency scaling"

trunk/arch/blackfin/Kconfig.debug

@@ -21,12 +21,6 @@ config DEBUG_STACK_USAGE
 config HAVE_ARCH_KGDB
 	def_bool y
 
-config KGDB_TESTCASE
-	tristate "KGDB: for test case in expect"
-	default n
-	help
-	  This is a kgdb test case for automated testing.
-
 config DEBUG_VERBOSE
 	bool "Verbose fault messages"
 	default y

trunk/arch/blackfin/configs/BF518F-EZBRD_defconfig

@@ -1,7 +1,7 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.28-rc2
-# Fri Jan  9 17:58:41 2009
+# Linux kernel version: 2.6.28
+# Fri Feb 20 10:01:44 2009
 #
 # CONFIG_MMU is not set
 # CONFIG_FPU is not set
@@ -133,10 +133,15 @@ CONFIG_BF518=y
 # CONFIG_BF538 is not set
 # CONFIG_BF539 is not set
 # CONFIG_BF542 is not set
+# CONFIG_BF542M is not set
 # CONFIG_BF544 is not set
+# CONFIG_BF544M is not set
 # CONFIG_BF547 is not set
+# CONFIG_BF547M is not set
 # CONFIG_BF548 is not set
+# CONFIG_BF548M is not set
 # CONFIG_BF549 is not set
+# CONFIG_BF549M is not set
 # CONFIG_BF561 is not set
 CONFIG_BF_REV_MIN=0
 CONFIG_BF_REV_MAX=2
@@ -426,7 +431,17 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
 # CONFIG_TIPC is not set
 # CONFIG_ATM is not set
 # CONFIG_BRIDGE is not set
-# CONFIG_NET_DSA is not set
+CONFIG_NET_DSA=y
+# CONFIG_NET_DSA_TAG_DSA is not set
+# CONFIG_NET_DSA_TAG_EDSA is not set
+# CONFIG_NET_DSA_TAG_TRAILER is not set
+CONFIG_NET_DSA_TAG_STPID=y
+# CONFIG_NET_DSA_MV88E6XXX is not set
+# CONFIG_NET_DSA_MV88E6060 is not set
+# CONFIG_NET_DSA_MV88E6XXX_NEED_PPU is not set
+# CONFIG_NET_DSA_MV88E6131 is not set
+# CONFIG_NET_DSA_MV88E6123_61_65 is not set
+CONFIG_NET_DSA_KSZ8893M=y
 # CONFIG_VLAN_8021Q is not set
 # CONFIG_DECNET is not set
 # CONFIG_LLC2 is not set
@@ -529,6 +544,8 @@ CONFIG_MTD_COMPLEX_MAPPINGS=y
 #
 # Self-contained MTD device drivers
 #
+# CONFIG_MTD_DATAFLASH is not set
+# CONFIG_MTD_M25P80 is not set
 # CONFIG_MTD_SLRAM is not set
 # CONFIG_MTD_PHRAM is not set
 # CONFIG_MTD_MTDRAM is not set
@@ -561,7 +578,9 @@ CONFIG_BLK_DEV_RAM_SIZE=4096
 # CONFIG_BLK_DEV_HD is not set
 CONFIG_MISC_DEVICES=y
 # CONFIG_EEPROM_93CX6 is not set
+# CONFIG_ICS932S401 is not set
 # CONFIG_ENCLOSURE_SERVICES is not set
+# CONFIG_C2PORT is not set
 CONFIG_HAVE_IDE=y
 # CONFIG_IDE is not set
 
@@ -607,6 +626,7 @@ CONFIG_BFIN_RX_DESC_NUM=20
 # CONFIG_SMC91X is not set
 # CONFIG_SMSC911X is not set
 # CONFIG_DM9000 is not set
+# CONFIG_ENC28J60 is not set
 # CONFIG_IBM_NEW_EMAC_ZMII is not set
 # CONFIG_IBM_NEW_EMAC_RGMII is not set
 # CONFIG_IBM_NEW_EMAC_TAH is not set
@@ -764,7 +784,23 @@ CONFIG_I2C_BLACKFIN_TWI_CLK_KHZ=100
 # CONFIG_I2C_DEBUG_ALGO is not set
 # CONFIG_I2C_DEBUG_BUS is not set
 # CONFIG_I2C_DEBUG_CHIP is not set
-# CONFIG_SPI is not set
+CONFIG_SPI=y
+# CONFIG_SPI_DEBUG is not set
+CONFIG_SPI_MASTER=y
+
+#
+# SPI Master Controller Drivers
+#
+CONFIG_SPI_BFIN=y
+# CONFIG_SPI_BFIN_LOCK is not set
+# CONFIG_SPI_BITBANG is not set
+
+#
+# SPI Protocol Masters
+#
+# CONFIG_SPI_AT25 is not set
+# CONFIG_SPI_SPIDEV is not set
+# CONFIG_SPI_TLE62X0 is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 # CONFIG_GPIOLIB is not set
 # CONFIG_W1 is not set
@@ -788,8 +824,10 @@ CONFIG_BFIN_WDT=y
 # CONFIG_MFD_SM501 is not set
 # CONFIG_HTC_PASIC3 is not set
 # CONFIG_MFD_TMIO is not set
+# CONFIG_PMIC_DA903X is not set
 # CONFIG_MFD_WM8400 is not set
 # CONFIG_MFD_WM8350_I2C is not set
+# CONFIG_REGULATOR is not set
 
 #
 # Multimedia devices
@@ -861,10 +899,18 @@ CONFIG_RTC_INTF_DEV=y
 # CONFIG_RTC_DRV_M41T80 is not set
 # CONFIG_RTC_DRV_S35390A is not set
 # CONFIG_RTC_DRV_FM3130 is not set
+# CONFIG_RTC_DRV_RX8581 is not set
 
 #
 # SPI RTC drivers
 #
+# CONFIG_RTC_DRV_M41T94 is not set
+# CONFIG_RTC_DRV_DS1305 is not set
+# CONFIG_RTC_DRV_DS1390 is not set
+# CONFIG_RTC_DRV_MAX6902 is not set
+# CONFIG_RTC_DRV_R9701 is not set
+# CONFIG_RTC_DRV_RS5C348 is not set
+# CONFIG_RTC_DRV_DS3234 is not set
 
 #
 # Platform RTC drivers
@@ -1062,12 +1108,20 @@ CONFIG_DEBUG_INFO=y
 # CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
 # CONFIG_FAULT_INJECTION is not set
 CONFIG_SYSCTL_SYSCALL_CHECK=y
+
+#
+# Tracers
+#
+# CONFIG_SCHED_TRACER is not set
+# CONFIG_CONTEXT_SWITCH_TRACER is not set
+# CONFIG_BOOT_TRACER is not set
 # CONFIG_DYNAMIC_PRINTK_DEBUG is not set
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
 # CONFIG_KGDB is not set
 # CONFIG_DEBUG_STACKOVERFLOW is not set
 # CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_KGDB_TESTCASE is not set
 CONFIG_DEBUG_VERBOSE=y
 CONFIG_DEBUG_MMRS=y
 # CONFIG_DEBUG_HWERR is not set
@@ -1100,6 +1154,7 @@ CONFIG_CRYPTO=y
 #
 # CONFIG_CRYPTO_FIPS is not set
 # CONFIG_CRYPTO_MANAGER is not set
+# CONFIG_CRYPTO_MANAGER2 is not set
 # CONFIG_CRYPTO_GF128MUL is not set
 # CONFIG_CRYPTO_NULL is not set
 # CONFIG_CRYPTO_CRYPTD is not set