---

yaml
---
r: 377434
b: refs/heads/master
c: a3d9dd8
h: refs/heads/master
v: v3

[refs]

@@ -1,2 +1,2 @@
 ---
-refs/heads/master: c8fc51cfa758be945c6113a4b446e0159070f768
+refs/heads/master: a3d9dd89b781bdcb14201847608b658442de812b

trunk/Documentation/bcache.txt

@@ -319,7 +319,10 @@ cache<0..n>
   Symlink to each of the cache devices comprising this cache set. 
 
 cache_available_percent
-  Percentage of cache device free.
+  Percentage of cache device which doesn't contain dirty data, and could
+  potentially be used for writeback.  This doesn't mean this space isn't used
+  for clean cached data; the unused statistic (in priority_stats) is typically
+  much lower.
 
 clear_stats
   Clears the statistics associated with this cache
@@ -423,8 +426,11 @@ nbuckets
   Total buckets in this cache
 
 priority_stats
-  Statistics about how recently data in the cache has been accessed.  This can
-  reveal your working set size.
+  Statistics about how recently data in the cache has been accessed.
+  This can reveal your working set size.  Unused is the percentage of
+  the cache that doesn't contain any data.  Metadata is bcache's
+  metadata overhead.  Average is the average priority of cache buckets.
+  Next is a list of quantiles with the priority threshold of each.
 
 written
   Sum of all data that has been written to the cache; comparison with

trunk/Documentation/devices.txt

@@ -498,12 +498,8 @@ Your cooperation is appreciated.
 
 		Each device type has 5 bits (32 minors).
 
- 13 block	8-bit MFM/RLL/IDE controller
-		  0 = /dev/xda		First XT disk whole disk
-		 64 = /dev/xdb		Second XT disk whole disk
-
-		Partitions are handled in the same way as IDE disks
-		(see major number 3).
+ 13 block	Previously used for the XT disk (/dev/xdN)
+		Deleted in kernel v3.9.
 
  14 char	Open Sound System (OSS)
 		  0 = /dev/mixer	Mixer control

trunk/Documentation/devicetree/bindings/net/macb.txt

@@ -4,7 +4,7 @@ Required properties:
 - compatible: Should be "cdns,[<chip>-]{macb|gem}"
   Use "cdns,at91sam9260-macb" Atmel at91sam9260 and at91sam9263 SoCs.
   Use "cdns,at32ap7000-macb" for other 10/100 usage or use the generic form: "cdns,macb".
-  Use "cnds,pc302-gem" for Picochip picoXcell pc302 and later devices based on
+  Use "cdns,pc302-gem" for Picochip picoXcell pc302 and later devices based on
   the Cadence GEM, or the generic form: "cdns,gem".
 - reg: Address and length of the register set for the device
 - interrupts: Should contain macb interrupt

trunk/Documentation/devicetree/bindings/rtc/atmel,at91rm9200-rtc.txt

@@ -1,7 +1,7 @@
 Atmel AT91RM9200 Real Time Clock
 
 Required properties:
-- compatible: should be: "atmel,at91rm9200-rtc"
+- compatible: should be: "atmel,at91rm9200-rtc" or "atmel,at91sam9x5-rtc"
 - reg: physical base address of the controller and length of memory mapped
   region.
 - interrupts: rtc alarm/event interrupt

trunk/Documentation/devicetree/bindings/video/simple-framebuffer.txt

@@ -0,0 +1,25 @@
+Simple Framebuffer
+
+A simple frame-buffer describes a raw memory region that may be rendered to,
+with the assumption that the display hardware has already been set up to scan
+out from that buffer.
+
+Required properties:
+- compatible: "simple-framebuffer"
+- reg: Should contain the location and size of the framebuffer memory.
+- width: The width of the framebuffer in pixels.
+- height: The height of the framebuffer in pixels.
+- stride: The number of bytes in each line of the framebuffer.
+- format: The format of the framebuffer surface. Valid values are:
+  - r5g6b5 (16-bit pixels, d[15:11]=r, d[10:5]=g, d[4:0]=b).
+
+Example:
+
+	framebuffer {
+		compatible = "simple-framebuffer";
+		reg = <0x1d385000 (1600 * 1200 * 2)>;
+		width = <1600>;
+		height = <1200>;
+		stride = <(1600 * 2)>;
+		format = "r5g6b5";
+	};

trunk/Documentation/dmatest.txt

@@ -34,7 +34,7 @@ command:
 After a while you will start to get messages about current status or error like
 in the original code.
 
-Note that running a new test will stop any in progress test.
+Note that running a new test will not stop any in progress test.
 
 The following command should return actual state of the test.
 	% cat /sys/kernel/debug/dmatest/run
@@ -52,8 +52,8 @@ To wait for test done the user may perform a busy loop that checks the state.
 
 The module parameters that is supplied to the kernel command line will be used
 for the first performed test. After user gets a control, the test could be
-interrupted or re-run with same or different parameters. For the details see
-the above section "Part 2 - When dmatest is built as a module..."
+re-run with the same or different parameters. For the details see the above
+section "Part 2 - When dmatest is built as a module..."
 
 In both cases the module parameters are used as initial values for the test case.
 You always could check them at run-time by running

trunk/Documentation/filesystems/xfs.txt

@@ -33,6 +33,9 @@ When mounting an XFS filesystem, the following options are accepted.
 	removing extended attributes) the on-disk superblock feature
 	bit field will be updated to reflect this format being in use.
 
+	CRC enabled filesystems always use the attr2 format, and so
+	will reject the noattr2 mount option if it is set.
+
   barrier
 	Enables the use of block layer write barriers for writes into
 	the journal and unwritten extent conversion.  This allows for

trunk/Documentation/kernel-parameters.txt

@@ -3351,9 +3351,6 @@ bytes respectively. Such letter suffixes can also be entirely omitted.
 			plus one apbt timer for broadcast timer.
 			x86_mrst_timer=apbt_only | lapic_and_apbt
 
-	xd=		[HW,XT] Original XT pre-IDE (RLL encoded) disks.
-	xd_geo=		See header of drivers/block/xd.c.
-
 	xen_emul_unplug=		[HW,X86,XEN]
 			Unplug Xen emulated devices
 			Format: [unplug0,][unplug1]

trunk/Documentation/m68k/kernel-options.txt

@@ -80,8 +80,6 @@ Valid names are:
   /dev/sdd: -> 0x0830 (forth SCSI disk)
   /dev/sde: -> 0x0840 (fifth SCSI disk)
   /dev/fd : -> 0x0200 (floppy disk)
-  /dev/xda: -> 0x0c00 (first XT disk, unused in Linux/m68k)
-  /dev/xdb: -> 0x0c40 (second XT disk, unused in Linux/m68k)
 
   The name must be followed by a decimal number, that stands for the
 partition number. Internally, the value of the number is just

trunk/Documentation/networking/ip-sysctl.txt

@@ -420,10 +420,10 @@ tcp_synack_retries - INTEGER
 	for a passive TCP connection will happen after 63seconds.
 
 tcp_syncookies - BOOLEAN
-	Only valid when the kernel was compiled with CONFIG_SYNCOOKIES
+	Only valid when the kernel was compiled with CONFIG_SYN_COOKIES
 	Send out syncookies when the syn backlog queue of a socket
 	overflows. This is to prevent against the common 'SYN flood attack'
-	Default: FALSE
+	Default: 1
 
 	Note, that syncookies is fallback facility.
 	It MUST NOT be used to help highly loaded servers to stand

trunk/Documentation/powerpc/transactional_memory.txt

@@ -147,6 +147,25 @@ Example signal handler:
       fix_the_problem(ucp->dar);
     }
 
+When in an active transaction that takes a signal, we need to be careful with
+the stack.  It's possible that the stack has moved back up after the tbegin.
+The obvious case here is when the tbegin is called inside a function that
+returns before a tend.  In this case, the stack is part of the checkpointed
+transactional memory state.  If we write over this non transactionally or in
+suspend, we are in trouble because if we get a tm abort, the program counter and
+stack pointer will be back at the tbegin but our in memory stack won't be valid
+anymore.
+
+To avoid this, when taking a signal in an active transaction, we need to use
+the stack pointer from the checkpointed state, rather than the speculated
+state.  This ensures that the signal context (written tm suspended) will be
+written below the stack required for the rollback.  The transaction is aborted
+becuase of the treclaim, so any memory written between the tbegin and the
+signal will be rolled back anyway.
+
+For signals taken in non-TM or suspended mode, we use the
+normal/non-checkpointed stack pointer.
+
 
 Failure cause codes used by kernel
 ==================================
@@ -155,14 +174,18 @@ These are defined in <asm/reg.h>, and distinguish different reasons why the
 kernel aborted a transaction:
 
  TM_CAUSE_RESCHED       Thread was rescheduled.
+ TM_CAUSE_TLBI          Software TLB invalide.
  TM_CAUSE_FAC_UNAV      FP/VEC/VSX unavailable trap.
  TM_CAUSE_SYSCALL       Currently unused; future syscalls that must abort
                         transactions for consistency will use this.
  TM_CAUSE_SIGNAL        Signal delivered.
  TM_CAUSE_MISC          Currently unused.
+ TM_CAUSE_ALIGNMENT     Alignment fault.
+ TM_CAUSE_EMULATE       Emulation that touched memory.
 
-These can be checked by the user program's abort handler as TEXASR[0:7].
-
+These can be checked by the user program's abort handler as TEXASR[0:7].  If
+bit 7 is set, it indicates that the error is consider persistent.  For example
+a TM_CAUSE_ALIGNMENT will be persistent while a TM_CAUSE_RESCHED will not.q
 
 GDB
 ===

trunk/Documentation/rapidio/rapidio.txt

@@ -79,20 +79,63 @@ master port that is used to communicate with devices within the network.
 In order to initialize the RapidIO subsystem, a platform must initialize and
 register at least one master port within the RapidIO network. To register mport
 within the subsystem controller driver initialization code calls function
-rio_register_mport() for each available master port. After all active master
-ports are registered with a RapidIO subsystem, the rio_init_mports() routine
-is called to perform enumeration and discovery.
+rio_register_mport() for each available master port.
 
-In the current PowerPC-based implementation a subsys_initcall() is specified to
-perform controller initialization and mport registration. At the end it directly
-calls rio_init_mports() to execute RapidIO enumeration and discovery.
+RapidIO subsystem uses subsys_initcall() or device_initcall() to perform
+controller initialization (depending on controller device type).
+
+After all active master ports are registered with a RapidIO subsystem,
+an enumeration and/or discovery routine may be called automatically or
+by user-space command.
 
 4. Enumeration and Discovery
 ----------------------------
 
-When rio_init_mports() is called it scans a list of registered master ports and
-calls an enumeration or discovery routine depending on the configured role of a
-master port: host or agent.
+4.1 Overview
+------------
+
+RapidIO subsystem configuration options allow users to specify enumeration and
+discovery methods as statically linked components or loadable modules.
+An enumeration/discovery method implementation and available input parameters
+define how any given method can be attached to available RapidIO mports:
+simply to all available mports OR individually to the specified mport device.
+
+Depending on selected enumeration/discovery build configuration, there are
+several methods to initiate an enumeration and/or discovery process:
+
+  (a) Statically linked enumeration and discovery process can be started
+  automatically during kernel initialization time using corresponding module
+  parameters. This was the original method used since introduction of RapidIO
+  subsystem. Now this method relies on enumerator module parameter which is
+  'rio-scan.scan' for existing basic enumeration/discovery method.
+  When automatic start of enumeration/discovery is used a user has to ensure
+  that all discovering endpoints are started before the enumerating endpoint
+  and are waiting for enumeration to be completed.
+  Configuration option CONFIG_RAPIDIO_DISC_TIMEOUT defines time that discovering
+  endpoint waits for enumeration to be completed. If the specified timeout
+  expires the discovery process is terminated without obtaining RapidIO network
+  information. NOTE: a timed out discovery process may be restarted later using
+  a user-space command as it is described later if the given endpoint was
+  enumerated successfully.
+
+  (b) Statically linked enumeration and discovery process can be started by
+  a command from user space. This initiation method provides more flexibility
+  for a system startup compared to the option (a) above. After all participating
+  endpoints have been successfully booted, an enumeration process shall be
+  started first by issuing a user-space command, after an enumeration is
+  completed a discovery process can be started on all remaining endpoints.
+
+  (c) Modular enumeration and discovery process can be started by a command from
+  user space. After an enumeration/discovery module is loaded, a network scan
+  process can be started by issuing a user-space command.
+  Similar to the option (b) above, an enumerator has to be started first.
+
+  (d) Modular enumeration and discovery process can be started by a module
+  initialization routine. In this case an enumerating module shall be loaded
+  first.
+
+When a network scan process is started it calls an enumeration or discovery
+routine depending on the configured role of a master port: host or agent.
 
 Enumeration is performed by a master port if it is configured as a host port by
 assigning a host device ID greater than or equal to zero. A host device ID is
@@ -104,8 +147,58 @@ for it.
 The enumeration and discovery routines use RapidIO maintenance transactions
 to access the configuration space of devices.
 
-The enumeration process is implemented according to the enumeration algorithm
-outlined in the RapidIO Interconnect Specification: Annex I [1].
+4.2 Automatic Start of Enumeration and Discovery
+------------------------------------------------
+
+Automatic enumeration/discovery start method is applicable only to built-in
+enumeration/discovery RapidIO configuration selection. To enable automatic
+enumeration/discovery start by existing basic enumerator method set use boot
+command line parameter "rio-scan.scan=1".
+
+This configuration requires synchronized start of all RapidIO endpoints that
+form a network which will be enumerated/discovered. Discovering endpoints have
+to be started before an enumeration starts to ensure that all RapidIO
+controllers have been initialized and are ready to be discovered. Configuration
+parameter CONFIG_RAPIDIO_DISC_TIMEOUT defines time (in seconds) which
+a discovering endpoint will wait for enumeration to be completed.
+
+When automatic enumeration/discovery start is selected, basic method's
+initialization routine calls rio_init_mports() to perform enumeration or
+discovery for all known mport devices.
+
+Depending on RapidIO network size and configuration this automatic
+enumeration/discovery start method may be difficult to use due to the
+requirement for synchronized start of all endpoints.
+
+4.3 User-space Start of Enumeration and Discovery
+-------------------------------------------------
+
+User-space start of enumeration and discovery can be used with built-in and
+modular build configurations. For user-space controlled start RapidIO subsystem
+creates the sysfs write-only attribute file '/sys/bus/rapidio/scan'. To initiate
+an enumeration or discovery process on specific mport device, a user needs to
+write mport_ID (not RapidIO destination ID) into that file. The mport_ID is a
+sequential number (0 ... RIO_MAX_MPORTS) assigned during mport device
+registration. For example for machine with single RapidIO controller, mport_ID
+for that controller always will be 0.
+
+To initiate RapidIO enumeration/discovery on all available mports a user may
+write '-1' (or RIO_MPORT_ANY) into the scan attribute file.
+
+4.4 Basic Enumeration Method
+----------------------------
+
+This is an original enumeration/discovery method which is available since
+first release of RapidIO subsystem code. The enumeration process is
+implemented according to the enumeration algorithm outlined in the RapidIO
+Interconnect Specification: Annex I [1].
+
+This method can be configured as statically linked or loadable module.
+The method's single parameter "scan" allows to trigger the enumeration/discovery
+process from module initialization routine.
+
+This enumeration/discovery method can be started only once and does not support
+unloading if it is built as a module.
 
 The enumeration process traverses the network using a recursive depth-first
 algorithm. When a new device is found, the enumerator takes ownership of that
@@ -160,6 +253,19 @@ time period. If this wait time period expires before enumeration is completed,
 an agent skips RapidIO discovery and continues with remaining kernel
 initialization.
 
+4.5 Adding New Enumeration/Discovery Method
+-------------------------------------------
+
+RapidIO subsystem code organization allows addition of new enumeration/discovery
+methods as new configuration options without significant impact to to the core
+RapidIO code.
+
+A new enumeration/discovery method has to be attached to one or more mport
+devices before an enumeration/discovery process can be started. Normally,
+method's module initialization routine calls rio_register_scan() to attach
+an enumerator to a specified mport device (or devices). The basic enumerator
+implementation demonstrates this process.
+
 5. References
 -------------
 

trunk/Documentation/rapidio/sysfs.txt

@@ -88,3 +88,20 @@ that exports additional attributes.
 
 IDT_GEN2:
  errlog - reads contents of device error log until it is empty.
+
+
+5. RapidIO Bus Attributes
+-------------------------
+
+RapidIO bus subdirectory /sys/bus/rapidio implements the following bus-specific
+attribute:
+
+  scan - allows to trigger enumeration discovery process from user space. This
+	 is a write-only attribute. To initiate an enumeration or discovery
+	 process on specific mport device, a user needs to write mport_ID (not
+	 RapidIO destination ID) into this file. The mport_ID is a sequential
+	 number (0 ... RIO_MAX_MPORTS) assigned to the mport device.
+	 For example, for a machine with a single RapidIO controller, mport_ID
+	 for that controller always will be 0.
+	 To initiate RapidIO enumeration/discovery on all available mports
+	 a user must write '-1' (or RIO_MPORT_ANY) into this attribute file.