---

yaml
---
r: 259374
b: refs/heads/master
c: b6fe70c
h: refs/heads/master
v: v3

[refs]

@@ -1,2 +1,2 @@
 ---
-refs/heads/master: 23d77de3a199ca70889cfd422a1244bbd7511f9d
+refs/heads/master: b6fe70c3aa866db38b72d1cf84b41c4cae80c87b

trunk/drivers/staging/brcm80211/brcmfmac/bcmchip.h

@@ -17,12 +17,6 @@
 #ifndef _bcmchip_h_
 #define _bcmchip_h_
 
-/* Core reg address translation */
-#define CORE_CC_REG(base, field)	(base + offsetof(chipcregs_t, field))
-#define CORE_BUS_REG(base, field)	(base + offsetof(sdpcmd_regs_t, field))
-#define CORE_SB(base, field) \
-		(base + SBCONFIGOFF + offsetof(sbconfig_t, field))
-
 /* bcm4329 */
 /* SDIO device core, ID 0x829 */
 #define BCM4329_CORE_BUS_BASE		0x18011000

trunk/drivers/staging/brcm80211/brcmfmac/dhd_sdio.c

@@ -230,6 +230,42 @@ typedef struct {
 /* Flags for SDH calls */
 #define F2SYNC	(SDIO_REQ_4BYTE | SDIO_REQ_FIXED)
 
+/* sbimstate */
+#define	SBIM_IBE		0x20000	/* inbanderror */
+#define	SBIM_TO			0x40000	/* timeout */
+#define	SBIM_BY			0x01800000	/* busy (sonics >= 2.3) */
+#define	SBIM_RJ			0x02000000	/* reject (sonics >= 2.3) */
+
+/* sbtmstatelow */
+#define	SBTML_RESET		0x0001	/* reset */
+#define	SBTML_REJ_MASK		0x0006	/* reject field */
+#define	SBTML_REJ		0x0002	/* reject */
+#define	SBTML_TMPREJ		0x0004	/* temporary reject, for error recovery */
+
+#define	SBTML_SICF_SHIFT	16	/* Shift to locate the SI control flags in sbtml */
+
+/* sbtmstatehigh */
+#define	SBTMH_SERR		0x0001	/* serror */
+#define	SBTMH_INT		0x0002	/* interrupt */
+#define	SBTMH_BUSY		0x0004	/* busy */
+#define	SBTMH_TO		0x0020	/* timeout (sonics >= 2.3) */
+
+#define	SBTMH_SISF_SHIFT	16	/* Shift to locate the SI status flags in sbtmh */
+
+/* sbidlow */
+#define	SBIDL_INIT		0x80	/* initiator */
+
+/* sbidhigh */
+#define	SBIDH_RC_MASK		0x000f	/* revision code */
+#define	SBIDH_RCE_MASK		0x7000	/* revision code extension field */
+#define	SBIDH_RCE_SHIFT		8
+#define	SBCOREREV(sbidh) \
+	((((sbidh) & SBIDH_RCE_MASK) >> SBIDH_RCE_SHIFT) | ((sbidh) & SBIDH_RC_MASK))
+#define	SBIDH_CC_MASK		0x8ff0	/* core code */
+#define	SBIDH_CC_SHIFT		4
+#define	SBIDH_VC_MASK		0xffff0000	/* vendor code */
+#define	SBIDH_VC_SHIFT		16
+
 /*
  * Conversion of 802.1D priority to precedence level
  */
@@ -241,6 +277,12 @@ DHD_SPINWAIT_SLEEP_INIT(sdioh_spinwait_sleep);
 extern int dhdcdc_set_ioctl(dhd_pub_t *dhd, int ifidx, uint cmd, void *buf,
 			    uint len);
 
+/* Core reg address translation */
+#define CORE_CC_REG(base, field)	(base + offsetof(chipcregs_t, field))
+#define CORE_BUS_REG(base, field)	(base + offsetof(sdpcmd_regs_t, field))
+#define CORE_SB(base, field) \
+		(base + SBCONFIGOFF + offsetof(sbconfig_t, field))
+
 #ifdef DHD_DEBUG
 /* Device console log buffer state */
 typedef struct dhd_console {
@@ -407,6 +449,50 @@ typedef struct dhd_bus {
 	bool ctrl_frame_stat;
 } dhd_bus_t;
 
+#ifndef _LANGUAGE_ASSEMBLY
+
+typedef volatile struct _sbconfig {
+	u32 PAD[2];
+	u32 sbipsflag;	/* initiator port ocp slave flag */
+	u32 PAD[3];
+	u32 sbtpsflag;	/* target port ocp slave flag */
+	u32 PAD[11];
+	u32 sbtmerrloga;	/* (sonics >= 2.3) */
+	u32 PAD;
+	u32 sbtmerrlog;	/* (sonics >= 2.3) */
+	u32 PAD[3];
+	u32 sbadmatch3;	/* address match3 */
+	u32 PAD;
+	u32 sbadmatch2;	/* address match2 */
+	u32 PAD;
+	u32 sbadmatch1;	/* address match1 */
+	u32 PAD[7];
+	u32 sbimstate;	/* initiator agent state */
+	u32 sbintvec;	/* interrupt mask */
+	u32 sbtmstatelow;	/* target state */
+	u32 sbtmstatehigh;	/* target state */
+	u32 sbbwa0;		/* bandwidth allocation table0 */
+	u32 PAD;
+	u32 sbimconfiglow;	/* initiator configuration */
+	u32 sbimconfighigh;	/* initiator configuration */
+	u32 sbadmatch0;	/* address match0 */
+	u32 PAD;
+	u32 sbtmconfiglow;	/* target configuration */
+	u32 sbtmconfighigh;	/* target configuration */
+	u32 sbbconfig;	/* broadcast configuration */
+	u32 PAD;
+	u32 sbbstate;	/* broadcast state */
+	u32 PAD[3];
+	u32 sbactcnfg;	/* activate configuration */
+	u32 PAD[3];
+	u32 sbflagst;	/* current sbflags */
+	u32 PAD[3];
+	u32 sbidlow;		/* identification */
+	u32 sbidhigh;	/* identification */
+} sbconfig_t;
+
+#endif				/* _LANGUAGE_ASSEMBLY */
+
 /* clkstate */
 #define CLK_NONE	0
 #define CLK_SDONLY	1

trunk/drivers/staging/brcm80211/include/sbsdpcmdev.h → trunk/drivers/staging/brcm80211/brcmfmac/sbsdpcmdev.h

@@ -24,13 +24,34 @@
 #define	PAD		_XSTR(__LINE__)
 #endif				/* PAD */
 
+/* dma registers per channel(xmt or rcv) */
+typedef volatile struct {
+	u32 control;		/* enable, et al */
+	u32 addr;		/* descriptor ring base address (4K aligned) */
+	u32 ptr;		/* last descriptor posted to chip */
+	u32 status;		/* current active descriptor, et al */
+} dma32regs_t;
+
+typedef volatile struct {
+	dma32regs_t xmt;	/* dma tx channel */
+	dma32regs_t rcv;	/* dma rx channel */
+} dma32regp_t;
+
 typedef volatile struct {
 	dma64regs_t xmt;	/* dma tx */
 	u32 PAD[2];
 	dma64regs_t rcv;	/* dma rx */
 	u32 PAD[2];
 } dma64p_t;
 
+
+typedef volatile struct {	/* diag access */
+	u32 fifoaddr;	/* diag address */
+	u32 fifodatalow;	/* low 32bits of data */
+	u32 fifodatahigh;	/* high 32bits of data */
+	u32 pad;		/* reserved */
+} dma64diag_t;
+
 /* dma64 sdiod corerev >= 1 */
 typedef volatile struct {
 	dma64p_t dma64regs[2];
@@ -144,7 +165,7 @@ typedef volatile struct {
 	u32 PAD[464];
 
 	/* Sonics SiliconBackplane registers */
-	sbconfig_t sbconfig;	/* SbConfig Regs, 0xf00-0xfff, rev8 */
+	u16 PAD[0x80];		/* SbConfig Regs, 0xf00-0xfff, rev8 */
 } sdpcmd_regs_t;
 
 /* corecontrol */

trunk/drivers/staging/brcm80211/brcmsmac/aiutils.c

@@ -35,6 +35,134 @@
 #include <bcmsrom.h>
 #include <wlc_pmu.h>
 
+/* slow_clk_ctl */
+#define SCC_SS_MASK		0x00000007	/* slow clock source mask */
+#define	SCC_SS_LPO		0x00000000	/* source of slow clock is LPO */
+#define	SCC_SS_XTAL		0x00000001	/* source of slow clock is crystal */
+#define	SCC_SS_PCI		0x00000002	/* source of slow clock is PCI */
+#define SCC_LF			0x00000200	/* LPOFreqSel, 1: 160Khz, 0: 32KHz */
+#define SCC_LP			0x00000400	/* LPOPowerDown, 1: LPO is disabled,
+						 * 0: LPO is enabled
+						 */
+#define SCC_FS			0x00000800	/* ForceSlowClk, 1: sb/cores running on slow clock,
+						 * 0: power logic control
+						 */
+#define SCC_IP			0x00001000	/* IgnorePllOffReq, 1/0: power logic ignores/honors
+						 * PLL clock disable requests from core
+						 */
+#define SCC_XC			0x00002000	/* XtalControlEn, 1/0: power logic does/doesn't
+						 * disable crystal when appropriate
+						 */
+#define SCC_XP			0x00004000	/* XtalPU (RO), 1/0: crystal running/disabled */
+#define SCC_CD_MASK		0xffff0000	/* ClockDivider (SlowClk = 1/(4+divisor)) */
+#define SCC_CD_SHIFT		16
+
+/* system_clk_ctl */
+#define	SYCC_IE			0x00000001	/* ILPen: Enable Idle Low Power */
+#define	SYCC_AE			0x00000002	/* ALPen: Enable Active Low Power */
+#define	SYCC_FP			0x00000004	/* ForcePLLOn */
+#define	SYCC_AR			0x00000008	/* Force ALP (or HT if ALPen is not set */
+#define	SYCC_HR			0x00000010	/* Force HT */
+#define SYCC_CD_MASK		0xffff0000	/* ClkDiv  (ILP = 1/(4 * (divisor + 1)) */
+#define SYCC_CD_SHIFT		16
+
+#define CST4329_SPROM_OTP_SEL_MASK	0x00000003
+#define CST4329_DEFCIS_SEL		0	/* OTP is powered up, use def. CIS, no SPROM */
+#define CST4329_SPROM_SEL		1	/* OTP is powered up, SPROM is present */
+#define CST4329_OTP_SEL			2	/* OTP is powered up, no SPROM */
+#define CST4329_OTP_PWRDN		3	/* OTP is powered down, SPROM is present */
+#define CST4329_SPI_SDIO_MODE_MASK	0x00000004
+#define CST4329_SPI_SDIO_MODE_SHIFT	2
+
+/* 43224 chip-specific ChipControl register bits */
+#define CCTRL43224_GPIO_TOGGLE          0x8000
+#define CCTRL_43224A0_12MA_LED_DRIVE    0x00F000F0	/* 12 mA drive strength */
+#define CCTRL_43224B0_12MA_LED_DRIVE    0xF0	/* 12 mA drive strength for later 43224s */
+
+/* 43236 Chip specific ChipStatus register bits */
+#define CST43236_SFLASH_MASK		0x00000040
+#define CST43236_OTP_MASK		0x00000080
+#define CST43236_HSIC_MASK		0x00000100	/* USB/HSIC */
+#define CST43236_BP_CLK			0x00000200	/* 120/96Mbps */
+#define CST43236_BOOT_MASK		0x00001800
+#define CST43236_BOOT_SHIFT		11
+#define CST43236_BOOT_FROM_SRAM		0	/* boot from SRAM, ARM in reset */
+#define CST43236_BOOT_FROM_ROM		1	/* boot from ROM */
+#define CST43236_BOOT_FROM_FLASH	2	/* boot from FLASH */
+#define CST43236_BOOT_FROM_INVALID	3
+
+/* 4331 chip-specific ChipControl register bits */
+#define CCTRL4331_BT_COEXIST		(1<<0)	/* 0 disable */
+#define CCTRL4331_SECI			(1<<1)	/* 0 SECI is disabled (JATG functional) */
+#define CCTRL4331_EXT_LNA		(1<<2)	/* 0 disable */
+#define CCTRL4331_SPROM_GPIO13_15       (1<<3)	/* sprom/gpio13-15 mux */
+#define CCTRL4331_EXTPA_EN		(1<<4)	/* 0 ext pa disable, 1 ext pa enabled */
+#define CCTRL4331_GPIOCLK_ON_SPROMCS	(1<<5)	/* set drive out GPIO_CLK on sprom_cs pin */
+#define CCTRL4331_PCIE_MDIO_ON_SPROMCS	(1<<6)	/* use sprom_cs pin as PCIE mdio interface */
+#define CCTRL4331_EXTPA_ON_GPIO2_5	(1<<7)	/* aband extpa will be at gpio2/5 and sprom_dout */
+#define CCTRL4331_OVR_PIPEAUXCLKEN	(1<<8)	/* override core control on pipe_AuxClkEnable */
+#define CCTRL4331_OVR_PIPEAUXPWRDOWN	(1<<9)	/* override core control on pipe_AuxPowerDown */
+#define CCTRL4331_PCIE_AUXCLKEN		(1<<10)	/* pcie_auxclkenable */
+#define CCTRL4331_PCIE_PIPE_PLLDOWN	(1<<11)	/* pcie_pipe_pllpowerdown */
+#define CCTRL4331_BT_SHD0_ON_GPIO4	(1<<16)	/* enable bt_shd0 at gpio4 */
+#define CCTRL4331_BT_SHD1_ON_GPIO5	(1<<17)	/* enable bt_shd1 at gpio5 */
+
+/* 4331 Chip specific ChipStatus register bits */
+#define	CST4331_XTAL_FREQ		0x00000001	/* crystal frequency 20/40Mhz */
+#define	CST4331_SPROM_PRESENT		0x00000002
+#define	CST4331_OTP_PRESENT		0x00000004
+#define	CST4331_LDO_RF			0x00000008
+#define	CST4331_LDO_PAR			0x00000010
+
+/* 4319 chip-specific ChipStatus register bits */
+#define	CST4319_SPI_CPULESSUSB		0x00000001
+#define	CST4319_SPI_CLK_POL		0x00000002
+#define	CST4319_SPI_CLK_PH		0x00000008
+#define	CST4319_SPROM_OTP_SEL_MASK	0x000000c0	/* gpio [7:6], SDIO CIS selection */
+#define	CST4319_SPROM_OTP_SEL_SHIFT	6
+#define	CST4319_DEFCIS_SEL		0x00000000	/* use default CIS, OTP is powered up */
+#define	CST4319_SPROM_SEL		0x00000040	/* use SPROM, OTP is powered up */
+#define	CST4319_OTP_SEL			0x00000080	/* use OTP, OTP is powered up */
+#define	CST4319_OTP_PWRDN		0x000000c0	/* use SPROM, OTP is powered down */
+#define	CST4319_SDIO_USB_MODE		0x00000100	/* gpio [8], sdio/usb mode */
+#define	CST4319_REMAP_SEL_MASK		0x00000600
+#define	CST4319_ILPDIV_EN		0x00000800
+#define	CST4319_XTAL_PD_POL		0x00001000
+#define	CST4319_LPO_SEL			0x00002000
+#define	CST4319_RES_INIT_MODE		0x0000c000
+#define	CST4319_PALDO_EXTPNP		0x00010000	/* PALDO is configured with external PNP */
+#define	CST4319_CBUCK_MODE_MASK		0x00060000
+#define CST4319_CBUCK_MODE_BURST	0x00020000
+#define CST4319_CBUCK_MODE_LPBURST	0x00060000
+#define	CST4319_RCAL_VALID		0x01000000
+#define	CST4319_RCAL_VALUE_MASK		0x3e000000
+#define	CST4319_RCAL_VALUE_SHIFT	25
+
+/* 4336 chip-specific ChipStatus register bits */
+#define	CST4336_SPI_MODE_MASK		0x00000001
+#define	CST4336_SPROM_PRESENT		0x00000002
+#define	CST4336_OTP_PRESENT		0x00000004
+#define	CST4336_ARMREMAP_0		0x00000008
+#define	CST4336_ILPDIV_EN_MASK		0x00000010
+#define	CST4336_ILPDIV_EN_SHIFT		4
+#define	CST4336_XTAL_PD_POL_MASK	0x00000020
+#define	CST4336_XTAL_PD_POL_SHIFT	5
+#define	CST4336_LPO_SEL_MASK		0x00000040
+#define	CST4336_LPO_SEL_SHIFT		6
+#define	CST4336_RES_INIT_MODE_MASK	0x00000180
+#define	CST4336_RES_INIT_MODE_SHIFT	7
+#define	CST4336_CBUCK_MODE_MASK		0x00000600
+#define	CST4336_CBUCK_MODE_SHIFT	9
+
+/* 4313 chip-specific ChipStatus register bits */
+#define	CST4313_SPROM_PRESENT			1
+#define	CST4313_OTP_PRESENT			2
+#define	CST4313_SPROM_OTP_SEL_MASK		0x00000002
+#define	CST4313_SPROM_OTP_SEL_SHIFT		0
+
+/* 4313 Chip specific ChipControl register bits */
+#define CCTRL_4313_12MA_LED_DRIVE    0x00000007	/* 12 mA drive strengh for later 4313 */
+
 #define BCM47162_DMP() ((sih->chip == BCM47162_CHIP_ID) && \
 		(sih->chiprev == 0) && \
 		(sii->coreid[sii->curidx] == MIPS74K_CORE_ID))

trunk/drivers/staging/brcm80211/brcmsmac/aiutils.h

@@ -225,6 +225,52 @@
 #define	BISZ_BSSEND_IDX		6	/*      6: bss end */
 #define BISZ_SIZE		7	/* descriptor size in 32-bit integers */
 
+#define	CC_SROM_OTP		0x800	/* SROM/OTP address space */
+
+/* gpiotimerval */
+#define GPIO_ONTIME_SHIFT	16
+
+/* Fields in clkdiv */
+#define	CLKD_OTP		0x000f0000
+#define	CLKD_OTP_SHIFT		16
+
+/* When Srom support present, fields in sromcontrol */
+#define	SRC_START		0x80000000
+#define	SRC_BUSY		0x80000000
+#define	SRC_OPCODE		0x60000000
+#define	SRC_OP_READ		0x00000000
+#define	SRC_OP_WRITE		0x20000000
+#define	SRC_OP_WRDIS		0x40000000
+#define	SRC_OP_WREN		0x60000000
+#define	SRC_OTPSEL		0x00000010
+#define	SRC_LOCK		0x00000008
+#define	SRC_SIZE_MASK		0x00000006
+#define	SRC_SIZE_1K		0x00000000
+#define	SRC_SIZE_4K		0x00000002
+#define	SRC_SIZE_16K		0x00000004
+#define	SRC_SIZE_SHIFT		1
+#define	SRC_PRESENT		0x00000001
+
+/* 4330 chip-specific ChipStatus register bits */
+#define CST4330_CHIPMODE_SDIOD(cs)	(((cs) & 0x7) < 6)	/* SDIO || gSPI */
+#define CST4330_CHIPMODE_USB20D(cs)	(((cs) & 0x7) >= 6)	/* USB || USBDA */
+#define CST4330_CHIPMODE_SDIO(cs)	(((cs) & 0x4) == 0)	/* SDIO */
+#define CST4330_CHIPMODE_GSPI(cs)	(((cs) & 0x6) == 4)	/* gSPI */
+#define CST4330_CHIPMODE_USB(cs)	(((cs) & 0x7) == 6)	/* USB packet-oriented */
+#define CST4330_CHIPMODE_USBDA(cs)	(((cs) & 0x7) == 7)	/* USB Direct Access */
+#define	CST4330_OTP_PRESENT		0x00000010
+#define	CST4330_LPO_AUTODET_EN		0x00000020
+#define	CST4330_ARMREMAP_0		0x00000040
+#define	CST4330_SPROM_PRESENT		0x00000080	/* takes priority over OTP if both set */
+#define	CST4330_ILPDIV_EN		0x00000100
+#define	CST4330_LPO_SEL			0x00000200
+#define	CST4330_RES_INIT_MODE_SHIFT	10
+#define	CST4330_RES_INIT_MODE_MASK	0x00000c00
+#define CST4330_CBUCK_MODE_SHIFT	12
+#define CST4330_CBUCK_MODE_MASK		0x00003000
+#define	CST4330_CBUCK_POWER_OK		0x00004000
+#define	CST4330_BB_PLL_LOCKED		0x00008000
+
 #define	SI_INFO(sih)	(si_info_t *)sih
 
 #define	GOODCOREADDR(x, b) \

trunk/drivers/staging/brcm80211/brcmsmac/bcmotp.c

@@ -29,6 +29,37 @@
 #include <sbchipc.h>
 #include <bcmotp.h>
 
+#define OTPS_GUP_MASK		0x00000f00
+#define OTPS_GUP_SHIFT		8
+#define OTPS_GUP_HW		0x00000100	/* h/w subregion is programmed */
+#define OTPS_GUP_SW		0x00000200	/* s/w subregion is programmed */
+#define OTPS_GUP_CI		0x00000400	/* chipid/pkgopt subregion is programmed */
+#define OTPS_GUP_FUSE		0x00000800	/* fuse subregion is programmed */
+
+/* Fields in otpprog in rev >= 21 and HND OTP */
+#define OTPP_COL_MASK		0x000000ff
+#define OTPP_COL_SHIFT		0
+#define OTPP_ROW_MASK		0x0000ff00
+#define OTPP_ROW_SHIFT		8
+#define OTPP_OC_MASK		0x0f000000
+#define OTPP_OC_SHIFT		24
+#define OTPP_READERR		0x10000000
+#define OTPP_VALUE_MASK		0x20000000
+#define OTPP_VALUE_SHIFT	29
+#define OTPP_START_BUSY		0x80000000
+#define	OTPP_READ		0x40000000	/* HND OTP */
+
+/* Opcodes for OTPP_OC field */
+#define OTPPOC_READ		0
+#define OTPPOC_BIT_PROG		1
+#define OTPPOC_VERIFY		3
+#define OTPPOC_INIT		4
+#define OTPPOC_SET		5
+#define OTPPOC_RESET		6
+#define OTPPOC_OCST		7
+#define OTPPOC_ROW_LOCK		8
+#define OTPPOC_PRESCN_TEST	9
+
 /*
  * There are two different OTP controllers so far:
  * 	1. new IPX OTP controller:	chipc 21, >=23