Merge branch 'at91' into devel

Documentation/devicetree/bindings/arm/atmel-at91.txt

@@ -7,6 +7,12 @@ PIT Timer required properties:
 - interrupts: Should contain interrupt for the PIT which is the IRQ line
   shared across all System Controller members.
 
+System Timer (ST) required properties:
+- compatible: Should be "atmel,at91rm9200-st"
+- reg: Should contain registers location and length
+- interrupts: Should contain interrupt for the ST which is the IRQ line
+  shared across all System Controller members.
+
 TC/TCLIB Timer required properties:
 - compatible: Should be "atmel,<chip>-tcb".
   <chip> can be "at91rm9200" or "at91sam9x5"

Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt

@@ -84,8 +84,13 @@ Required properties for pin configuration node:
   The PERIPH 0 means gpio.
 
 Bits used for CONFIG:
-PULL_UP(1 << 0): indicate this pin need a pull up.
-MULTIDRIVE(1 << 1): indicate this pin need to be configured as multidrive.
+PULL_UP		(1 << 0): indicate this pin need a pull up.
+MULTIDRIVE	(1 << 1): indicate this pin need to be configured as multidrive.
+DEGLITCH	(1 << 2): indicate this pin need deglitch.
+PULL_DOWN	(1 << 3): indicate this pin need a pull down.
+DIS_SCHMIT	(1 << 4): indicate this pin need to disable schmit trigger.
+DEBOUNCE	(1 << 16): indicate this pin need debounce.
+DEBOUNCE_VAL	(0x3fff << 17): debounce val.
 
 NOTE:
 Some requirements for using atmel,at91rm9200-pinctrl binding:

arch/arm/boot/dts/Makefile

@@ -1,7 +1,10 @@
 ifeq ($(CONFIG_OF),y)
 
 # Keep at91 dtb files sorted alphabetically for each SoC
+# rm9200
+dtb-$(CONFIG_ARCH_AT91) += at91rm9200ek.dtb
 # sam9260
+dtb-$(CONFIG_ARCH_AT91) += animeo_ip.dtb
 dtb-$(CONFIG_ARCH_AT91) += aks-cdu.dtb
 dtb-$(CONFIG_ARCH_AT91) += ethernut5.dtb
 dtb-$(CONFIG_ARCH_AT91) += evk-pro3.dtb
@@ -19,6 +22,7 @@ dtb-$(CONFIG_ARCH_AT91) += tny_a9g20.dtb
 dtb-$(CONFIG_ARCH_AT91) += usb_a9g20.dtb
 # sam9g45
 dtb-$(CONFIG_ARCH_AT91) += at91sam9m10g45ek.dtb
+dtb-$(CONFIG_ARCH_AT91) += pm9g45.dtb
 # sam9n12
 dtb-$(CONFIG_ARCH_AT91) += at91sam9n12ek.dtb
 # sam9x5

arch/arm/boot/dts/animeo_ip.dts

@@ -0,0 +1,178 @@
+/*
+ * animeo_ip.dts - Device Tree file for Somfy Animeo IP Boards
+ *
+ *  Copyright (C) 2011-2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+ *
+ * Licensed under GPLv2 only.
+ */
+
+/dts-v1/;
+/include/ "at91sam9260.dtsi"
+
+/ {
+	model = "Somfy Animeo IP";
+	compatible = "somfy,animeo-ip", "atmel,at91sam9260", "atmel,at91sam9";
+
+	aliases {
+		serial0 = &usart1;
+		serial1 = &usart2;
+		serial2 = &usart0;
+		serial3 = &dbgu;
+		serial4 = &usart3;
+		serial5 = &uart0;
+		serial6 = &uart1;
+	};
+
+	chosen {
+		linux,stdout-path = &usart2;
+	};
+
+	memory {
+		reg = <0x20000000 0x4000000>;
+	};
+
+	clocks {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		main_clock: clock@0 {
+			compatible = "atmel,osc", "fixed-clock";
+			clock-frequency = <18432000>;
+		};
+	};
+
+	ahb {
+		apb {
+			usart0: serial@fffb0000 {
+				pinctrl-0 = <&pinctrl_usart0 &pinctrl_usart0_rts>;
+				linux,rs485-enabled-at-boot-time;
+				status = "okay";
+			};
+
+			usart1: serial@fffb4000 {
+				pinctrl-0 = <&pinctrl_usart1 &pinctrl_usart1_rts>;
+				linux,rs485-enabled-at-boot-time;
+				status = "okay";
+			};
+
+			usart2: serial@fffb8000 {
+				pinctrl-0 = <&pinctrl_usart2>;
+				status = "okay";
+			};
+
+			macb0: ethernet@fffc4000 {
+				pinctrl-0 = <&pinctrl_macb_rmii &pinctrl_macb_rmii_mii>;
+				phy-mode = "mii";
+				status = "okay";
+			};
+
+			mmc0: mmc@fffa8000 {
+				pinctrl-0 = <&pinctrl_mmc0_clk
+					     &pinctrl_mmc0_slot1_cmd_dat0
+					     &pinctrl_mmc0_slot1_dat1_3>;
+				status = "okay";
+
+				slot@1 {
+					reg = <1>;
+					bus-width = <4>;
+				};
+			};
+		};
+
+		nand0: nand@40000000 {
+			nand-bus-width = <8>;
+			nand-ecc-mode = "soft";
+			nand-on-flash-bbt;
+			status = "okay";
+
+			at91bootstrap@0 {
+				label = "at91bootstrap";
+				reg = <0x0 0x8000>;
+			};
+
+			barebox@8000 {
+				label = "barebox";
+				reg = <0x8000 0x40000>;
+			};
+
+			bareboxenv@48000 {
+				label = "bareboxenv";
+				reg = <0x48000 0x8000>;
+			};
+
+			user_block@0x50000 {
+				label = "user_block";
+				reg = <0x50000 0xb0000>;
+			};
+
+			kernel@100000 {
+				label = "kernel";
+				reg = <0x100000 0x1b0000>;
+			};
+
+			root@2b0000 {
+				label = "root";
+				reg = <0x2b0000 0x1D50000>;
+			};
+		};
+
+		usb0: ohci@00500000 {
+			num-ports = <2>;
+			atmel,vbus-gpio = <&pioB 15 1>;
+			status = "okay";
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		power_green {
+			label = "power_green";
+			gpios = <&pioC 17 0>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		power_red {
+			label = "power_red";
+			gpios = <&pioA 2 0>;
+		};
+
+		tx_green {
+			label = "tx_green";
+			gpios = <&pioC 19 0>;
+		};
+
+		tx_red {
+			label = "tx_red";
+			gpios = <&pioC 18 0>;
+		};
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		keyswitch_in {
+			label = "keyswitch_in";
+			gpios = <&pioB 1 0>;
+			linux,code = <28>;
+			gpio-key,wakeup;
+		};
+
+		error_in {
+			label = "error_in";
+			gpios = <&pioB 2 0>;
+			linux,code = <29>;
+			gpio-key,wakeup;
+		};
+
+		btn {
+			label = "btn";
+			gpios = <&pioC 23 0>;
+			linux,code = <31>;
+			gpio-key,wakeup;
+		};
+	};
+};