Merge master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6

* master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6: (23 commits)
  ide: add support for SCSI ioctls to ide-floppy
  ide: remove stale changelog from setup-pci.c
  ide: remove stale changelog/comments/TODO from ide.c
  ide-cris: handle PIO auto-tuning in tune_cris_ide()
  ide: add PIO masks
  ide: remove ide_find_best_pio_mode()
  ide: drop "PIO data" argument from ide_get_best_pio_mode()
  ide: ide_find_best_pio_mode() fixes (take 2)
  ide: add ide_pio_cycle_time() helper (take 2)
  sc1200: remove stale Power Management code
  ide: ide_start_power_step() fix WRT disabling DMA
  serverworks: fix DMA
  serverworks: always tune PIO
  ide: add ide_pci_device_t.host_flags (take 2)
  ide: add ide_dev_has_iordy() helper (take 4)
  ide: make ide_get_best_pio_mode() print info if overriding PIO mode
  siimage: PIO mode setup fixes (take 2)
  atiixp: PIO mode setup fixes
  ide: Stop mapping ROMs
  IDE: Remove references to dead ETRAX-related variables.
  ...

drivers/ata/pata_pcmcia.c

@@ -382,6 +382,7 @@ static struct pcmcia_device_id pcmcia_devices[] = {
 	PCMCIA_DEVICE_PROD_ID12("HITACHI", "microdrive", 0xf4f43949, 0xa6d76178),
 	PCMCIA_DEVICE_PROD_ID12("IBM", "microdrive", 0xb569a6e5, 0xa6d76178),
 	PCMCIA_DEVICE_PROD_ID12("IBM", "IBM17JSSFP20", 0xb569a6e5, 0xf2508753),
+	PCMCIA_DEVICE_PROD_ID12("KINGSTON", "CF8GB", 0x2e6d1829, 0xacbe682e),
 	PCMCIA_DEVICE_PROD_ID12("IO DATA", "CBIDE2      ", 0x547e66dc, 0x8671043b),
 	PCMCIA_DEVICE_PROD_ID12("IO DATA", "PCIDE", 0x547e66dc, 0x5c5ab149),
 	PCMCIA_DEVICE_PROD_ID12("IO DATA", "PCIDEII", 0x547e66dc, 0xb3662674),

drivers/ide/cris/ide-cris.c

@@ -414,12 +414,6 @@ cris_ide_reset(unsigned val)
 #ifdef CONFIG_ETRAX_IDE_G27_RESET
 	REG_SHADOW_SET(R_PORT_G_DATA, port_g_data_shadow, 27, val);
 #endif
-#ifdef CONFIG_ETRAX_IDE_CSE1_16_RESET
-	REG_SHADOW_SET(port_cse1_addr, port_cse1_shadow, 16, val);
-#endif
-#ifdef CONFIG_ETRAX_IDE_CSP0_8_RESET
-	REG_SHADOW_SET(port_csp0_addr, port_csp0_shadow, 8, val);
-#endif
 #ifdef CONFIG_ETRAX_IDE_PB7_RESET
 	port_pb_dir_shadow = port_pb_dir_shadow |
 		IO_STATE(R_PORT_PB_DIR, dir7, output);
@@ -690,6 +684,8 @@ static void tune_cris_ide(ide_drive_t *drive, u8 pio)
 {
 	int setup, strobe, hold;
 
+	pio = ide_get_best_pio_mode(drive, pio, 4);
+
 	switch(pio)
 	{
 		case 0:
@@ -820,6 +816,7 @@ init_e100_ide (void)
 		hwif->dma_host_on = &cris_dma_on;
 		hwif->dma_off_quietly = &cris_dma_off;
 		hwif->cbl = ATA_CBL_PATA40;
+		hwif->pio_mask = ATA_PIO4,
 		hwif->ultra_mask = cris_ultra_mask;
 		hwif->mwdma_mask = 0x07; /* Multiword DMA 0-2 */
 		hwif->autodma = 1;

drivers/ide/ide-floppy.c

@@ -99,6 +99,8 @@
 #include <linux/bitops.h>
 #include <linux/mutex.h>
 
+#include <scsi/scsi_ioctl.h>
+
 #include <asm/byteorder.h>
 #include <asm/irq.h>
 #include <asm/uaccess.h>
@@ -2099,7 +2101,21 @@ static int idefloppy_ioctl(struct inode *inode, struct file *file,
 	case IDEFLOPPY_IOCTL_FORMAT_GET_PROGRESS:
 		return idefloppy_get_format_progress(drive, argp);
 	}
-	return generic_ide_ioctl(drive, file, bdev, cmd, arg);
+
+	/*
+	 * skip SCSI_IOCTL_SEND_COMMAND (deprecated)
+	 * and CDROM_SEND_PACKET (legacy) ioctls
+	 */
+	if (cmd != CDROM_SEND_PACKET && cmd != SCSI_IOCTL_SEND_COMMAND)
+		err = scsi_cmd_ioctl(file, bdev->bd_disk->queue,
+					bdev->bd_disk, cmd, argp);
+	else
+		err = -ENOTTY;
+
+	if (err == -ENOTTY)
+		err = generic_ide_ioctl(drive, file, bdev, cmd, arg);
+
+	return err;
 }
 
 static int idefloppy_media_changed(struct gendisk *disk)

drivers/ide/ide-io.c

@@ -224,11 +224,12 @@ static ide_startstop_t ide_start_power_step(ide_drive_t *drive, struct request *
 		 * we could be smarter and check for current xfer_speed
 		 * in struct drive etc...
 		 */
-		if ((drive->id->capability & 1) == 0)
-			break;
 		if (drive->hwif->ide_dma_check == NULL)
 			break;
 		drive->hwif->dma_off_quietly(drive);
+		/*
+		 * TODO: respect ->using_dma setting
+		 */
 		ide_set_dma(drive);
 		break;
 	}

drivers/ide/ide-lib.c

@@ -249,12 +249,34 @@ static int ide_scan_pio_blacklist (char *model)
 	return -1;
 }
 
+unsigned int ide_pio_cycle_time(ide_drive_t *drive, u8 pio)
+{
+	struct hd_driveid *id = drive->id;
+	int cycle_time = 0;
+
+	if (id->field_valid & 2) {
+		if (id->capability & 8)
+			cycle_time = id->eide_pio_iordy;
+		else
+			cycle_time = id->eide_pio;
+	}
+
+	/* conservative "downgrade" for all pre-ATA2 drives */
+	if (pio < 3) {
+		if (cycle_time && cycle_time < ide_pio_timings[pio].cycle_time)
+			cycle_time = 0; /* use standard timing */
+	}
+
+	return cycle_time ? cycle_time : ide_pio_timings[pio].cycle_time;
+}
+
+EXPORT_SYMBOL_GPL(ide_pio_cycle_time);
+
 /**
  *	ide_get_best_pio_mode	-	get PIO mode from drive
  *	@drive: drive to consider
  *	@mode_wanted: preferred mode
  *	@max_mode: highest allowed mode
- *	@d: PIO data
  *
  *	This routine returns the recommended PIO settings for a given drive,
  *	based on the drive->id information and the ide_pio_blacklist[].
@@ -263,32 +285,26 @@ static int ide_scan_pio_blacklist (char *model)
  *	This is used by most chipset support modules when "auto-tuning".
  */
 
-u8 ide_get_best_pio_mode (ide_drive_t *drive, u8 mode_wanted, u8 max_mode, ide_pio_data_t *d)
+u8 ide_get_best_pio_mode (ide_drive_t *drive, u8 mode_wanted, u8 max_mode)
 {
 	int pio_mode;
-	int cycle_time = 0;
-	int use_iordy = 0;
 	struct hd_driveid* id = drive->id;
 	int overridden  = 0;
 
-	if (mode_wanted != 255) {
-		pio_mode = mode_wanted;
-		use_iordy = (pio_mode > 2);
-	} else if (!drive->id) {
-		pio_mode = 0;
-	} else if ((pio_mode = ide_scan_pio_blacklist(id->model)) != -1) {
-		overridden = 1;
-		use_iordy = (pio_mode > 2);
+	if (mode_wanted != 255)
+		return min_t(u8, mode_wanted, max_mode);
+
+	if ((drive->hwif->host_flags & IDE_HFLAG_PIO_NO_BLACKLIST) == 0 &&
+	    (pio_mode = ide_scan_pio_blacklist(id->model)) != -1) {
+		printk(KERN_INFO "%s: is on PIO blacklist\n", drive->name);
 	} else {
 		pio_mode = id->tPIO;
 		if (pio_mode > 2) {	/* 2 is maximum allowed tPIO value */
 			pio_mode = 2;
 			overridden = 1;
 		}
 		if (id->field_valid & 2) {	  /* drive implements ATA2? */
-			if (id->capability & 8) { /* drive supports use_iordy? */
-				use_iordy = 1;
-				cycle_time = id->eide_pio_iordy;
+			if (id->capability & 8) { /* IORDY supported? */
 				if (id->eide_pio_modes & 7) {
 					overridden = 0;
 					if (id->eide_pio_modes & 4)
@@ -298,31 +314,27 @@ u8 ide_get_best_pio_mode (ide_drive_t *drive, u8 mode_wanted, u8 max_mode, ide_p
 					else
 						pio_mode = 3;
 				}
-			} else {
-				cycle_time = id->eide_pio;
 			}
 		}
 
+		if (overridden)
+			printk(KERN_INFO "%s: tPIO > 2, assuming tPIO = 2\n",
+					 drive->name);
+
 		/*
 		 * Conservative "downgrade" for all pre-ATA2 drives
 		 */
-		if (pio_mode && pio_mode < 4) {
+		if ((drive->hwif->host_flags & IDE_HFLAG_PIO_NO_DOWNGRADE) == 0 &&
+		    pio_mode && pio_mode < 4) {
 			pio_mode--;
-			overridden = 1;
-			if (cycle_time && cycle_time < ide_pio_timings[pio_mode].cycle_time)
-				cycle_time = 0; /* use standard timing */
+			printk(KERN_INFO "%s: applying conservative "
+					 "PIO \"downgrade\"\n", drive->name);
 		}
 	}
-	if (pio_mode > max_mode) {
+
+	if (pio_mode > max_mode)
 		pio_mode = max_mode;
-		cycle_time = 0;
-	}
-	if (d) {
-		d->pio_mode = pio_mode;
-		d->cycle_time = cycle_time ? cycle_time : ide_pio_timings[pio_mode].cycle_time;
-		d->use_iordy = use_iordy;
-		d->overridden = overridden;
-	}
+
 	return pio_mode;
 }
 

drivers/ide/ide-timing.h

@@ -106,23 +106,6 @@ static struct ide_timing ide_timing[] = {
 #define XFER_EPIO	0x01
 #define XFER_PIO	0x00
 
-static short ide_find_best_pio_mode(ide_drive_t *drive)
-{
-	struct hd_driveid *id = drive->id;
-	short best = 0;
-
-	if (id->field_valid & 2) {	/* EIDE PIO modes */
-
-		if ((best = (drive->id->eide_pio_modes & 4) ? XFER_PIO_5 :
-			    (drive->id->eide_pio_modes & 2) ? XFER_PIO_4 :
-			    (drive->id->eide_pio_modes & 1) ? XFER_PIO_3 : 0)) return best;
-	}
-
-	return  (drive->id->tPIO == 2) ? XFER_PIO_2 :
-		(drive->id->tPIO == 1) ? XFER_PIO_1 :
-		(drive->id->tPIO == 0) ? XFER_PIO_0 : XFER_PIO_SLOW;
-}
-
 static void ide_timing_quantize(struct ide_timing *t, struct ide_timing *q, int T, int UT)
 {
 	q->setup   = EZ(t->setup   * 1000,  T);
@@ -212,7 +195,8 @@ static int ide_timing_compute(ide_drive_t *drive, short speed, struct ide_timing
  */
 
 	if ((speed & XFER_MODE) != XFER_PIO) {
-		ide_timing_compute(drive, ide_find_best_pio_mode(drive), &p, T, UT);
+		u8 pio = ide_get_best_pio_mode(drive, 255, 5);
+		ide_timing_compute(drive, XFER_PIO_0 + pio, &p, T, UT);
 		ide_timing_merge(&p, t, t, IDE_TIMING_ALL);
 	}
 

drivers/ide/ide.c

@@ -16,10 +16,6 @@
  *   (usually 14 & 15).
  * There can be up to two drives per interface, as per the ATA-2 spec.
  *
- * Primary:    ide0, port 0x1f0; major=3;  hda is minor=0; hdb is minor=64
- * Secondary:  ide1, port 0x170; major=22; hdc is minor=0; hdd is minor=64
- * Tertiary:   ide2, port 0x???; major=33; hde is minor=0; hdf is minor=64
- * Quaternary: ide3, port 0x???; major=34; hdg is minor=0; hdh is minor=64
  * ...
  *
  *  From hd.c:
@@ -47,80 +43,6 @@
  *  This was a rewrite of just about everything from hd.c, though some original
  *  code is still sprinkled about.  Think of it as a major evolution, with
  *  inspiration from lots of linux users, esp.  hamish@zot.apana.org.au
- *
- *  Version 1.0 ALPHA	initial code, primary i/f working okay
- *  Version 1.3 BETA	dual i/f on shared irq tested & working!
- *  Version 1.4 BETA	added auto probing for irq(s)
- *  Version 1.5 BETA	added ALPHA (untested) support for IDE cd-roms,
- *  ...
- * Version 5.50		allow values as small as 20 for idebus=
- * Version 5.51		force non io_32bit in drive_cmd_intr()
- *			change delay_10ms() to delay_50ms() to fix problems
- * Version 5.52		fix incorrect invalidation of removable devices
- *			add "hdx=slow" command line option
- * Version 5.60		start to modularize the driver; the disk and ATAPI
- *			 drivers can be compiled as loadable modules.
- *			move IDE probe code to ide-probe.c
- *			move IDE disk code to ide-disk.c
- *			add support for generic IDE device subdrivers
- *			add m68k code from Geert Uytterhoeven
- *			probe all interfaces by default
- *			add ioctl to (re)probe an interface
- * Version 6.00		use per device request queues
- *			attempt to optimize shared hwgroup performance
- *			add ioctl to manually adjust bandwidth algorithms
- *			add kerneld support for the probe module
- *			fix bug in ide_error()
- *			fix bug in the first ide_get_lock() call for Atari
- *			don't flush leftover data for ATAPI devices
- * Version 6.01		clear hwgroup->active while the hwgroup sleeps
- *			support HDIO_GETGEO for floppies
- * Version 6.02		fix ide_ack_intr() call
- *			check partition table on floppies
- * Version 6.03		handle bad status bit sequencing in ide_wait_stat()
- * Version 6.10		deleted old entries from this list of updates
- *			replaced triton.c with ide-dma.c generic PCI DMA
- *			added support for BIOS-enabled UltraDMA
- *			rename all "promise" things to "pdc4030"
- *			fix EZ-DRIVE handling on small disks
- * Version 6.11		fix probe error in ide_scan_devices()
- *			fix ancient "jiffies" polling bugs
- *			mask all hwgroup interrupts on each irq entry
- * Version 6.12		integrate ioctl and proc interfaces
- *			fix parsing of "idex=" command line parameter
- * Version 6.13		add support for ide4/ide5 courtesy rjones@orchestream.com
- * Version 6.14		fixed IRQ sharing among PCI devices
- * Version 6.15		added SMP awareness to IDE drivers
- * Version 6.16		fixed various bugs; even more SMP friendly
- * Version 6.17		fix for newest EZ-Drive problem
- * Version 6.18		default unpartitioned-disk translation now "BIOS LBA"
- * Version 6.19		Re-design for a UNIFORM driver for all platforms,
- *			  model based on suggestions from Russell King and
- *			  Geert Uytterhoeven
- *			Promise DC4030VL now supported.
- *			add support for ide6/ide7
- *			delay_50ms() changed to ide_delay_50ms() and exported.
- * Version 6.20		Added/Fixed Generic ATA-66 support and hwif detection.
- *			Added hdx=flash to allow for second flash disk
- *			  detection w/o the hang loop.
- *			Added support for ide8/ide9
- *			Added idex=ata66 for the quirky chipsets that are
- *			  ATA-66 compliant, but have yet to determine a method
- *			  of verification of the 80c cable presence.
- *			  Specifically Promise's PDC20262 chipset.
- * Version 6.21		Fixing/Fixed SMP spinlock issue with insight from an old
- *			  hat that clarified original low level driver design.
- * Version 6.30		Added SMP support; fixed multmode issues.  -ml
- * Version 6.31		Debug Share INTR's and request queue streaming
- *			Native ATA-100 support
- *			Prep for Cascades Project
- * Version 7.00alpha	First named revision of ide rearrange
- *
- *  Some additional driver compile-time options are in ./include/linux/ide.h
- *
- *  To do, in likely order of completion:
- *	- modify kernel to obtain BIOS geometry for drives on 2nd/3rd/4th i/f
- *
  */
 
 #define	REVISION	"Revision: 7.00alpha2"
@@ -455,6 +377,10 @@ static void ide_hwif_restore(ide_hwif_t *hwif, ide_hwif_t *tmp_hwif)
 	hwif->straight8			= tmp_hwif->straight8;
 	hwif->bus_state			= tmp_hwif->bus_state;
 
+	hwif->host_flags		= tmp_hwif->host_flags;
+
+	hwif->pio_mask			= tmp_hwif->pio_mask;
+
 	hwif->atapi_dma			= tmp_hwif->atapi_dma;
 	hwif->ultra_mask		= tmp_hwif->ultra_mask;
 	hwif->mwdma_mask		= tmp_hwif->mwdma_mask;
@@ -1171,10 +1097,6 @@ int generic_ide_ioctl(ide_drive_t *drive, struct file *file, struct block_device
 			return 0;
 		}
 
-		case CDROMEJECT:
-		case CDROMCLOSETRAY:
-			return scsi_cmd_ioctl(file, bdev->bd_disk->queue, bdev->bd_disk, cmd, p);
-
 		case HDIO_GET_BUSSTATE:
 			if (!capable(CAP_SYS_ADMIN))
 				return -EACCES;

drivers/ide/legacy/ali14xx.c

@@ -115,13 +115,12 @@ static void ali14xx_tune_drive (ide_drive_t *drive, u8 pio)
 	int time1, time2;
 	u8 param1, param2, param3, param4;
 	unsigned long flags;
-	ide_pio_data_t d;
 	int bus_speed = system_bus_clock();
 
-	pio = ide_get_best_pio_mode(drive, pio, ALI_MAX_PIO, &d);
+	pio = ide_get_best_pio_mode(drive, pio, ALI_MAX_PIO);
 
 	/* calculate timing, according to PIO mode */
-	time1 = d.cycle_time;
+	time1 = ide_pio_cycle_time(drive, pio);
 	time2 = ide_pio_timings[pio].active_time;
 	param3 = param1 = (time2 * bus_speed + 999) / 1000;
 	param4 = param2 = (time1 * bus_speed + 999) / 1000 - param1;
@@ -212,10 +211,12 @@ static int __init ali14xx_probe(void)
 	mate = &ide_hwifs[1];
 
 	hwif->chipset = ide_ali14xx;
+	hwif->pio_mask = ATA_PIO4;
 	hwif->tuneproc = &ali14xx_tune_drive;
 	hwif->mate = mate;
 
 	mate->chipset = ide_ali14xx;
+	mate->pio_mask = ATA_PIO4;
 	mate->tuneproc = &ali14xx_tune_drive;
 	mate->mate = hwif;
 	mate->channel = 1;

drivers/ide/legacy/dtc2278.c

@@ -71,7 +71,7 @@ static void tune_dtc2278 (ide_drive_t *drive, u8 pio)
 {
 	unsigned long flags;
 
-	pio = ide_get_best_pio_mode(drive, pio, 4, NULL);
+	pio = ide_get_best_pio_mode(drive, pio, 4);
 
 	if (pio >= 3) {
 		spin_lock_irqsave(&ide_lock, flags);
@@ -123,6 +123,7 @@ static int __init dtc2278_probe(void)
 
 	hwif->serialized = 1;
 	hwif->chipset = ide_dtc2278;
+	hwif->pio_mask = ATA_PIO4;
 	hwif->tuneproc = &tune_dtc2278;
 	hwif->drives[0].no_unmask = 1;
 	hwif->drives[1].no_unmask = 1;