---

yaml
---
r: 90392
b: refs/heads/master
c: 57bb7e2
h: refs/heads/master
v: v3

[refs]

@@ -1,2 +1,2 @@
 ---
-refs/heads/master: b39b5a2bc339d8ea04fde2e343bcb4c8f38df692
+refs/heads/master: 57bb7e222804c68066e3e995dffbedda5b1ec1ea

trunk/drivers/net/phy/broadcom.c

@@ -99,6 +99,41 @@ static int bcm54xx_config_intr(struct phy_device *phydev)
 	return err;
 }
 
+static int bcm5481_config_aneg(struct phy_device *phydev)
+{
+	int ret;
+
+	/* Aneg firsly. */
+	ret = genphy_config_aneg(phydev);
+
+	/* Then we can set up the delay. */
+	if (phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID) {
+		u16 reg;
+
+		/*
+		 * There is no BCM5481 specification available, so down
+		 * here is everything we know about "register 0x18". This
+		 * at least helps BCM5481 to successfuly receive packets
+		 * on MPC8360E-RDK board. Peter Barada <peterb@logicpd.com>
+		 * says: "This sets delay between the RXD and RXC signals
+		 * instead of using trace lengths to achieve timing".
+		 */
+
+		/* Set RDX clk delay. */
+		reg = 0x7 | (0x7 << 12);
+		phy_write(phydev, 0x18, reg);
+
+		reg = phy_read(phydev, 0x18);
+		/* Set RDX-RXC skew. */
+		reg |= (1 << 8);
+		/* Write bits 14:0. */
+		reg |= (1 << 15);
+		phy_write(phydev, 0x18, reg);
+	}
+
+	return ret;
+}
+
 static struct phy_driver bcm5411_driver = {
 	.phy_id		= 0x00206070,
 	.phy_id_mask	= 0xfffffff0,
@@ -141,8 +176,22 @@ static struct phy_driver bcm5461_driver = {
 	.driver 	= { .owner = THIS_MODULE },
 };
 
+static struct phy_driver bcm5481_driver = {
+	.phy_id		= 0x0143bca0,
+	.phy_id_mask	= 0xfffffff0,
+	.name		= "Broadcom BCM5481",
+	.features	= PHY_GBIT_FEATURES,
+	.flags		= PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
+	.config_init	= bcm54xx_config_init,
+	.config_aneg	= bcm5481_config_aneg,
+	.read_status	= genphy_read_status,
+	.ack_interrupt	= bcm54xx_ack_interrupt,
+	.config_intr	= bcm54xx_config_intr,
+	.driver 	= { .owner = THIS_MODULE },
+};
+
 static struct phy_driver bcm5482_driver = {
-    .phy_id		= 0x0143bcb0,
+	.phy_id		= 0x0143bcb0,
 	.phy_id_mask	= 0xfffffff0,
 	.name		= "Broadcom BCM5482",
 	.features	= PHY_GBIT_FEATURES,
@@ -168,12 +217,17 @@ static int __init broadcom_init(void)
 	ret = phy_driver_register(&bcm5461_driver);
 	if (ret)
 		goto out_5461;
+	ret = phy_driver_register(&bcm5481_driver);
+	if (ret)
+		goto out_5481;
 	ret = phy_driver_register(&bcm5482_driver);
 	if (ret)
 		goto out_5482;
 	return ret;
 
 out_5482:
+	phy_driver_unregister(&bcm5481_driver);
+out_5481:
 	phy_driver_unregister(&bcm5461_driver);
 out_5461:
 	phy_driver_unregister(&bcm5421_driver);
@@ -186,6 +240,7 @@ static int __init broadcom_init(void)
 static void __exit broadcom_exit(void)
 {
 	phy_driver_unregister(&bcm5482_driver);
+	phy_driver_unregister(&bcm5481_driver);
 	phy_driver_unregister(&bcm5461_driver);
 	phy_driver_unregister(&bcm5421_driver);
 	phy_driver_unregister(&bcm5411_driver);