---

yaml
---
r: 272897
b: refs/heads/master
c: c541c15
h: refs/heads/master
i:
  272895: 6dc06f5
v: v3

[refs]

@@ -1,2 +1,2 @@
 ---
-refs/heads/master: dc9ca24f4d7a5ff33d7e12ca809564d37188212b
+refs/heads/master: c541c15fb5ab48c47bc9b90121538fd30d152f23

trunk/Documentation/hwmon/coretemp

@@ -35,23 +35,17 @@ the Out-Of-Spec bit. Following table summarizes the exported sysfs files:
 All Sysfs entries are named with their core_id (represented here by 'X').
 tempX_input	 - Core temperature (in millidegrees Celsius).
 tempX_max	 - All cooling devices should be turned on (on Core2).
-		   Initialized with IA32_THERM_INTERRUPT. When the CPU
-		   temperature reaches this temperature, an interrupt is
-		   generated and tempX_max_alarm is set.
-tempX_max_hyst   - If the CPU temperature falls below than temperature,
-		   an interrupt is generated and tempX_max_alarm is reset.
-tempX_max_alarm  - Set if the temperature reaches or exceeds tempX_max.
-		   Reset if the temperature drops to or below tempX_max_hyst.
 tempX_crit	 - Maximum junction temperature (in millidegrees Celsius).
 tempX_crit_alarm - Set when Out-of-spec bit is set, never clears.
 		   Correct CPU operation is no longer guaranteed.
 tempX_label	 - Contains string "Core X", where X is processor
 		   number. For Package temp, this will be "Physical id Y",
 		   where Y is the package number.
 
-The TjMax temperature is set to 85 degrees C if undocumented model specific
-register (UMSR) 0xee has bit 30 set. If not the TjMax is 100 degrees C as
-(sometimes) documented in processor datasheet.
+On CPU models which support it, TjMax is read from a model-specific register.
+On other models, it is set to an arbitrary value based on weak heuristics.
+If these heuristics don't work for you, you can pass the correct TjMax value
+as a module parameter (tjmax).
 
 Appendix A. Known TjMax lists (TBD):
 Some information comes from ark.intel.com

trunk/Documentation/vm/transhuge.txt

@@ -123,10 +123,11 @@ be automatically shutdown if it's set to "never".
 khugepaged runs usually at low frequency so while one may not want to
 invoke defrag algorithms synchronously during the page faults, it
 should be worth invoking defrag at least in khugepaged. However it's
-also possible to disable defrag in khugepaged:
+also possible to disable defrag in khugepaged by writing 0 or enable
+defrag in khugepaged by writing 1:
 
-echo yes >/sys/kernel/mm/transparent_hugepage/khugepaged/defrag
-echo no >/sys/kernel/mm/transparent_hugepage/khugepaged/defrag
+echo 0 >/sys/kernel/mm/transparent_hugepage/khugepaged/defrag
+echo 1 >/sys/kernel/mm/transparent_hugepage/khugepaged/defrag
 
 You can also control how many pages khugepaged should scan at each
 pass:

trunk/Makefile

@@ -1,7 +1,7 @@
 VERSION = 3
 PATCHLEVEL = 1
 SUBLEVEL = 0
-EXTRAVERSION = -rc7
+EXTRAVERSION = -rc8
 NAME = "Divemaster Edition"
 
 # *DOCUMENTATION*

trunk/arch/arm/Kconfig

@@ -1283,6 +1283,20 @@ config ARM_ERRATA_364296
 	  processor into full low interrupt latency mode. ARM11MPCore
 	  is not affected.
 
+config ARM_ERRATA_764369
+	bool "ARM errata: Data cache line maintenance operation by MVA may not succeed"
+	depends on CPU_V7 && SMP
+	help
+	  This option enables the workaround for erratum 764369
+	  affecting Cortex-A9 MPCore with two or more processors (all
+	  current revisions). Under certain timing circumstances, a data
+	  cache line maintenance operation by MVA targeting an Inner
+	  Shareable memory region may fail to proceed up to either the
+	  Point of Coherency or to the Point of Unification of the
+	  system. This workaround adds a DSB instruction before the
+	  relevant cache maintenance functions and sets a specific bit
+	  in the diagnostic control register of the SCU.
+
 endmenu
 
 source "arch/arm/common/Kconfig"

trunk/arch/arm/include/asm/device.h

@@ -12,7 +12,12 @@ struct dev_archdata {
 #endif
 };
 
+struct omap_device;
+
 struct pdev_archdata {
+#ifdef CONFIG_ARCH_OMAP
+	struct omap_device *od;
+#endif
 };
 
 #endif

trunk/arch/arm/include/asm/futex.h

@@ -25,17 +25,17 @@
 
 #ifdef CONFIG_SMP
 
-#define __futex_atomic_op(insn, ret, oldval, uaddr, oparg)	\
+#define __futex_atomic_op(insn, ret, oldval, tmp, uaddr, oparg)	\
 	smp_mb();						\
 	__asm__ __volatile__(					\
-	"1:	ldrex	%1, [%2]\n"				\
+	"1:	ldrex	%1, [%3]\n"				\
 	"	" insn "\n"					\
-	"2:	strex	%1, %0, [%2]\n"				\
-	"	teq	%1, #0\n"				\
+	"2:	strex	%2, %0, [%3]\n"				\
+	"	teq	%2, #0\n"				\
 	"	bne	1b\n"					\
 	"	mov	%0, #0\n"				\
-	__futex_atomic_ex_table("%4")				\
-	: "=&r" (ret), "=&r" (oldval)				\
+	__futex_atomic_ex_table("%5")				\
+	: "=&r" (ret), "=&r" (oldval), "=&r" (tmp)		\
 	: "r" (uaddr), "r" (oparg), "Ir" (-EFAULT)		\
 	: "cc", "memory")
 
@@ -73,14 +73,14 @@ futex_atomic_cmpxchg_inatomic(u32 *uval, u32 __user *uaddr,
 #include <linux/preempt.h>
 #include <asm/domain.h>
 
-#define __futex_atomic_op(insn, ret, oldval, uaddr, oparg)	\
+#define __futex_atomic_op(insn, ret, oldval, tmp, uaddr, oparg)	\
 	__asm__ __volatile__(					\
-	"1:	" T(ldr) "	%1, [%2]\n"			\
+	"1:	" T(ldr) "	%1, [%3]\n"			\
 	"	" insn "\n"					\
-	"2:	" T(str) "	%0, [%2]\n"			\
+	"2:	" T(str) "	%0, [%3]\n"			\
 	"	mov	%0, #0\n"				\
-	__futex_atomic_ex_table("%4")				\
-	: "=&r" (ret), "=&r" (oldval)				\
+	__futex_atomic_ex_table("%5")				\
+	: "=&r" (ret), "=&r" (oldval), "=&r" (tmp)		\
 	: "r" (uaddr), "r" (oparg), "Ir" (-EFAULT)		\
 	: "cc", "memory")
 
@@ -117,7 +117,7 @@ futex_atomic_op_inuser (int encoded_op, u32 __user *uaddr)
 	int cmp = (encoded_op >> 24) & 15;
 	int oparg = (encoded_op << 8) >> 20;
 	int cmparg = (encoded_op << 20) >> 20;
-	int oldval = 0, ret;
+	int oldval = 0, ret, tmp;
 
 	if (encoded_op & (FUTEX_OP_OPARG_SHIFT << 28))
 		oparg = 1 << oparg;
@@ -129,19 +129,19 @@ futex_atomic_op_inuser (int encoded_op, u32 __user *uaddr)
 
 	switch (op) {
 	case FUTEX_OP_SET:
-		__futex_atomic_op("mov	%0, %3", ret, oldval, uaddr, oparg);
+		__futex_atomic_op("mov	%0, %4", ret, oldval, tmp, uaddr, oparg);
 		break;
 	case FUTEX_OP_ADD:
-		__futex_atomic_op("add	%0, %1, %3", ret, oldval, uaddr, oparg);
+		__futex_atomic_op("add	%0, %1, %4", ret, oldval, tmp, uaddr, oparg);
 		break;
 	case FUTEX_OP_OR:
-		__futex_atomic_op("orr	%0, %1, %3", ret, oldval, uaddr, oparg);
+		__futex_atomic_op("orr	%0, %1, %4", ret, oldval, tmp, uaddr, oparg);
 		break;
 	case FUTEX_OP_ANDN:
-		__futex_atomic_op("and	%0, %1, %3", ret, oldval, uaddr, ~oparg);
+		__futex_atomic_op("and	%0, %1, %4", ret, oldval, tmp, uaddr, ~oparg);
 		break;
 	case FUTEX_OP_XOR:
-		__futex_atomic_op("eor	%0, %1, %3", ret, oldval, uaddr, oparg);
+		__futex_atomic_op("eor	%0, %1, %4", ret, oldval, tmp, uaddr, oparg);
 		break;
 	default:
 		ret = -ENOSYS;

trunk/arch/arm/include/asm/unistd.h

@@ -478,8 +478,8 @@
 /*
  * Unimplemented (or alternatively implemented) syscalls
  */
-#define __IGNORE_fadvise64_64		1
-#define __IGNORE_migrate_pages		1
+#define __IGNORE_fadvise64_64
+#define __IGNORE_migrate_pages
 
 #endif /* __KERNEL__ */
 #endif /* __ASM_ARM_UNISTD_H */

trunk/arch/arm/kernel/smp_scu.c

@@ -13,6 +13,7 @@
 
 #include <asm/smp_scu.h>
 #include <asm/cacheflush.h>
+#include <asm/cputype.h>
 
 #define SCU_CTRL		0x00
 #define SCU_CONFIG		0x04
@@ -37,6 +38,15 @@ void __init scu_enable(void __iomem *scu_base)
 {
 	u32 scu_ctrl;
 
+#ifdef CONFIG_ARM_ERRATA_764369
+	/* Cortex-A9 only */
+	if ((read_cpuid(CPUID_ID) & 0xff0ffff0) == 0x410fc090) {
+		scu_ctrl = __raw_readl(scu_base + 0x30);
+		if (!(scu_ctrl & 1))
+			__raw_writel(scu_ctrl | 0x1, scu_base + 0x30);
+	}
+#endif
+
 	scu_ctrl = __raw_readl(scu_base + SCU_CTRL);
 	/* already enabled? */
 	if (scu_ctrl & 1)

trunk/arch/arm/kernel/vmlinux.lds.S

@@ -23,8 +23,10 @@
 
 #if defined(CONFIG_SMP_ON_UP) && !defined(CONFIG_DEBUG_SPINLOCK)
 #define ARM_EXIT_KEEP(x)	x
+#define ARM_EXIT_DISCARD(x)
 #else
 #define ARM_EXIT_KEEP(x)
+#define ARM_EXIT_DISCARD(x)	x
 #endif
 
 OUTPUT_ARCH(arm)
@@ -39,6 +41,11 @@ jiffies = jiffies_64 + 4;
 SECTIONS
 {
 	/*
+	 * XXX: The linker does not define how output sections are
+	 * assigned to input sections when there are multiple statements
+	 * matching the same input section name.  There is no documented
+	 * order of matching.
+	 *
 	 * unwind exit sections must be discarded before the rest of the
 	 * unwind sections get included.
 	 */
@@ -47,6 +54,9 @@ SECTIONS
 		*(.ARM.extab.exit.text)
 		ARM_CPU_DISCARD(*(.ARM.exidx.cpuexit.text))
 		ARM_CPU_DISCARD(*(.ARM.extab.cpuexit.text))
+		ARM_EXIT_DISCARD(EXIT_TEXT)
+		ARM_EXIT_DISCARD(EXIT_DATA)
+		EXIT_CALL
 #ifndef CONFIG_HOTPLUG
 		*(.ARM.exidx.devexit.text)
 		*(.ARM.extab.devexit.text)
@@ -58,6 +68,8 @@ SECTIONS
 #ifndef CONFIG_SMP_ON_UP
 		*(.alt.smp.init)
 #endif
+		*(.discard)
+		*(.discard.*)
 	}
 
 #ifdef CONFIG_XIP_KERNEL
@@ -279,9 +291,6 @@ SECTIONS
 
 	STABS_DEBUG
 	.comment 0 : { *(.comment) }
-
-	/* Default discards */
-	DISCARDS
 }
 
 /*

trunk/arch/arm/mach-exynos4/clock.c

@@ -899,8 +899,7 @@ static struct clksrc_clk clksrcs[] = {
 		.reg_div = { .reg = S5P_CLKDIV_CAM, .shift = 28, .size = 4 },
 	}, {
 		.clk		= {
-			.name		= "sclk_cam",
-			.devname	= "exynos4-fimc.0",
+			.name		= "sclk_cam0",
 			.enable		= exynos4_clksrc_mask_cam_ctrl,
 			.ctrlbit	= (1 << 16),
 		},
@@ -909,8 +908,7 @@ static struct clksrc_clk clksrcs[] = {
 		.reg_div = { .reg = S5P_CLKDIV_CAM, .shift = 16, .size = 4 },
 	}, {
 		.clk		= {
-			.name		= "sclk_cam",
-			.devname	= "exynos4-fimc.1",
+			.name		= "sclk_cam1",
 			.enable		= exynos4_clksrc_mask_cam_ctrl,
 			.ctrlbit	= (1 << 20),
 		},

trunk/arch/arm/mach-omap1/Makefile

@@ -4,7 +4,7 @@
 
 # Common support
 obj-y := io.o id.o sram.o time.o irq.o mux.o flash.o serial.o devices.o dma.o
-obj-y += clock.o clock_data.o opp_data.o reset.o pm_bus.o
+obj-y += clock.o clock_data.o opp_data.o reset.o pm_bus.o timer.o
 
 obj-$(CONFIG_OMAP_MCBSP) += mcbsp.o
 

trunk/arch/arm/mach-omap1/mcbsp.c

@@ -31,6 +31,7 @@
 static int dsp_use;
 static struct clk *api_clk;
 static struct clk *dsp_clk;
+static struct platform_device **omap_mcbsp_devices;
 
 static void omap1_mcbsp_request(unsigned int id)
 {
@@ -78,6 +79,17 @@ static struct omap_mcbsp_ops omap1_mcbsp_ops = {
 	.free		= omap1_mcbsp_free,
 };
 
+#define OMAP7XX_MCBSP1_BASE	0xfffb1000
+#define OMAP7XX_MCBSP2_BASE	0xfffb1800
+
+#define OMAP1510_MCBSP1_BASE	0xe1011800
+#define OMAP1510_MCBSP2_BASE	0xfffb1000
+#define OMAP1510_MCBSP3_BASE	0xe1017000
+
+#define OMAP1610_MCBSP1_BASE	0xe1011800
+#define OMAP1610_MCBSP2_BASE	0xfffb1000
+#define OMAP1610_MCBSP3_BASE	0xe1017000
+
 #if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
 struct resource omap7xx_mcbsp_res[][6] = {
 	{
@@ -369,6 +381,39 @@ static struct omap_mcbsp_platform_data omap16xx_mcbsp_pdata[] = {
 #define OMAP16XX_MCBSP_COUNT		0
 #endif
 
+static void omap_mcbsp_register_board_cfg(struct resource *res, int res_count,
+			struct omap_mcbsp_platform_data *config, int size)
+{
+	int i;
+
+	omap_mcbsp_devices = kzalloc(size * sizeof(struct platform_device *),
+				     GFP_KERNEL);
+	if (!omap_mcbsp_devices) {
+		printk(KERN_ERR "Could not register McBSP devices\n");
+		return;
+	}
+
+	for (i = 0; i < size; i++) {
+		struct platform_device *new_mcbsp;
+		int ret;
+
+		new_mcbsp = platform_device_alloc("omap-mcbsp", i + 1);
+		if (!new_mcbsp)
+			continue;
+		platform_device_add_resources(new_mcbsp, &res[i * res_count],
+					res_count);
+		config[i].reg_size = 2;
+		config[i].reg_step = 2;
+		new_mcbsp->dev.platform_data = &config[i];
+		ret = platform_device_add(new_mcbsp);
+		if (ret) {
+			platform_device_put(new_mcbsp);
+			continue;
+		}
+		omap_mcbsp_devices[i] = new_mcbsp;
+	}
+}
+
 static int __init omap1_mcbsp_init(void)
 {
 	if (!cpu_class_is_omap1())