---

yaml
---
r: 188189
b: refs/heads/master
c: 2a5e00e
h: refs/heads/master
i:
  188187: b8a85c3
v: v3

[refs]

@@ -1,2 +1,2 @@
 ---
-refs/heads/master: fb40b496ad8bbe60a60c25eb2fce20f3cc114679
+refs/heads/master: 2a5e00ed14e27908dae698900473a65cc53ccd82

trunk/Documentation/kernel-parameters.txt

@@ -199,6 +199,10 @@ and is between 256 and 4096 characters. It is defined in the file
 			acpi_display_output=video
 			See above.
 
+	acpi_early_pdc_eval	[HW,ACPI] Evaluate processor _PDC methods
+				early. Needed on some platforms to properly
+				initialize the EC.
+
 	acpi_irq_balance [HW,ACPI]
 			ACPI will balance active IRQs
 			default in APIC mode
@@ -311,6 +315,11 @@ and is between 256 and 4096 characters. It is defined in the file
 	aic79xx=	[HW,SCSI]
 			See Documentation/scsi/aic79xx.txt.
 
+	alignment=	[KNL,ARM]
+			Allow the default userspace alignment fault handler
+			behaviour to be specified.  Bit 0 enables warnings,
+			bit 1 enables fixups, and bit 2 sends a segfault.
+
 	amd_iommu=	[HW,X86-84]
 			Pass parameters to the AMD IOMMU driver in the system.
 			Possible values are:

trunk/Documentation/networking/ip-sysctl.txt

@@ -1074,10 +1074,10 @@ regen_max_retry - INTEGER
 	Default: 5
 
 max_addresses - INTEGER
-	Number of maximum addresses per interface.  0 disables limitation.
-	It is recommended not set too large value (or 0) because it would
-	be too easy way to crash kernel to allow to create too much of
-	autoconfigured addresses.
+	Maximum number of autoconfigured addresses per interface.  Setting
+	to zero disables the limitation.  It is not recommended to set this
+	value too large (or to zero) because it would be an easy way to
+	crash the kernel by allowing too many addresses to be created.
 	Default: 16
 
 disable_ipv6 - BOOLEAN

trunk/Documentation/sound/alsa/HD-Audio-Models.txt

@@ -124,6 +124,8 @@ ALC882/883/885/888/889
   asus-a7m	ASUS A7M
   macpro	MacPro support
   mb5		Macbook 5,1
+  macmini3	Macmini 3,1
+  mba21		Macbook Air 2,1
   mbp3		Macbook Pro rev3
   imac24	iMac 24'' with jack detection
   imac91	iMac 9,1
@@ -279,13 +281,16 @@ Conexant 5051
   laptop	Basic Laptop config (default)
   hp		HP Spartan laptop
   hp-dv6736	HP dv6736
+  hp-f700	HP Compaq Presario F700
   lenovo-x200	Lenovo X200 laptop
+  toshiba	Toshiba Satellite M300
 
 Conexant 5066
 =============
   laptop	Basic Laptop config (default)
   dell-laptop	Dell laptops
   olpc-xo-1_5	OLPC XO 1.5
+  ideapad       Lenovo IdeaPad U150
 
 STAC9200
 ========

trunk/Documentation/sound/alsa/HD-Audio.txt

@@ -452,6 +452,33 @@ Similarly, the lines after `[verb]` are parsed as `init_verbs`
 sysfs entries, and the lines after `[hint]` are parsed as `hints`
 sysfs entries, respectively.
 
+Another example to override the codec vendor id from 0x12345678 to
+0xdeadbeef is like below:
+------------------------------------------------------------------------
+  [codec]
+  0x12345678 0xabcd1234 2
+
+  [vendor_id]
+  0xdeadbeef
+------------------------------------------------------------------------
+
+In the similar way, you can override the codec subsystem_id via
+`[subsystem_id]`, the revision id via `[revision_id]` line.
+Also, the codec chip name can be rewritten via `[chip_name]` line.
+------------------------------------------------------------------------
+  [codec]
+  0x12345678 0xabcd1234 2
+
+  [subsystem_id]
+  0xffff1111
+
+  [revision_id]
+  0x10
+
+  [chip_name]
+  My-own NEWS-0002
+------------------------------------------------------------------------
+
 The hd-audio driver reads the file via request_firmware().  Thus,
 a patch file has to be located on the appropriate firmware path,
 typically, /lib/firmware.  For example, when you pass the option

trunk/MAINTAINERS

@@ -616,10 +616,10 @@ M:	Richard Purdie <rpurdie@rpsys.net>
 S:	Maintained
 
 ARM/CORTINA SYSTEMS GEMINI ARM ARCHITECTURE
-M:	Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
+M:	Paulius Zaleckas <paulius.zaleckas@gmail.com>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 T:	git git://gitorious.org/linux-gemini/mainline.git
-S:	Maintained
+S:	Odd Fixes
 F:	arch/arm/mach-gemini/
 
 ARM/EBSA110 MACHINE SUPPORT
@@ -641,9 +641,9 @@ T:	topgit git://git.openezx.org/openezx.git
 F:	arch/arm/mach-pxa/ezx.c
 
 ARM/FARADAY FA526 PORT
-M:	Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
+M:	Paulius Zaleckas <paulius.zaleckas@gmail.com>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
-S:	Maintained
+S:	Odd Fixes
 F:	arch/arm/mm/*-fa*
 
 ARM/FOOTBRIDGE ARCHITECTURE
@@ -1733,10 +1733,9 @@ F:	include/linux/tfrc.h
 F:	net/dccp/
 
 DECnet NETWORK LAYER
-M:	Christine Caulfield <christine.caulfield@googlemail.com>
 W:	http://linux-decnet.sourceforge.net
 L:	linux-decnet-user@lists.sourceforge.net
-S:	Maintained
+S:	Orphan
 F:	Documentation/networking/decnet.txt
 F:	net/decnet/
 
@@ -3490,9 +3489,9 @@ S:	Maintained
 F:	drivers/net/wireless/libertas/
 
 MARVELL MV643XX ETHERNET DRIVER
-M:	Lennert Buytenhek <buytenh@marvell.com>
+M:	Lennert Buytenhek <buytenh@wantstofly.org>
 L:	netdev@vger.kernel.org
-S:	Supported
+S:	Maintained
 F:	drivers/net/mv643xx_eth.*
 F:	include/linux/mv643xx.h
 

trunk/Makefile

@@ -1,7 +1,7 @@
 VERSION = 2
 PATCHLEVEL = 6
 SUBLEVEL = 33
-EXTRAVERSION = -rc8
+EXTRAVERSION =
 NAME = Man-Eating Seals of Antiquity
 
 # *DOCUMENTATION*

trunk/arch/arm/include/asm/cacheflush.h

@@ -42,7 +42,8 @@
 #endif
 
 #if defined(CONFIG_CPU_ARM920T) || defined(CONFIG_CPU_ARM922T) || \
-    defined(CONFIG_CPU_ARM925T) || defined(CONFIG_CPU_ARM1020)
+    defined(CONFIG_CPU_ARM925T) || defined(CONFIG_CPU_ARM1020) || \
+    defined(CONFIG_CPU_ARM1026)
 # define MULTI_CACHE 1
 #endif
 

trunk/arch/arm/kernel/setup.c

@@ -102,6 +102,7 @@ struct cpu_cache_fns cpu_cache;
 #endif
 #ifdef CONFIG_OUTER_CACHE
 struct outer_cache_fns outer_cache;
+EXPORT_SYMBOL(outer_cache);
 #endif
 
 struct stack {

trunk/arch/arm/mach-gemini/gpio.c

@@ -86,7 +86,7 @@ static int gpio_set_irq_type(unsigned int irq, unsigned int type)
 	unsigned int reg_both, reg_level, reg_type;
 
 	reg_type = __raw_readl(base + GPIO_INT_TYPE);
-	reg_level = __raw_readl(base + GPIO_INT_BOTH_EDGE);
+	reg_level = __raw_readl(base + GPIO_INT_LEVEL);
 	reg_both = __raw_readl(base + GPIO_INT_BOTH_EDGE);
 
 	switch (type) {
@@ -117,7 +117,7 @@ static int gpio_set_irq_type(unsigned int irq, unsigned int type)
 	}
 
 	__raw_writel(reg_type, base + GPIO_INT_TYPE);
-	__raw_writel(reg_level, base + GPIO_INT_BOTH_EDGE);
+	__raw_writel(reg_level, base + GPIO_INT_LEVEL);
 	__raw_writel(reg_both, base + GPIO_INT_BOTH_EDGE);
 
 	gpio_ack_irq(irq);

trunk/arch/arm/mach-omap2/mux.c

@@ -961,16 +961,14 @@ static void __init omap_mux_init_list(struct omap_mux *superset)
 	while (superset->reg_offset !=  OMAP_MUX_TERMINATOR) {
 		struct omap_mux *entry;
 
-#ifndef CONFIG_OMAP_MUX
-		/* Skip pins that are not muxed as GPIO by bootloader */
-		if (!OMAP_MODE_GPIO(omap_mux_read(superset->reg_offset))) {
+#ifdef CONFIG_OMAP_MUX
+		if (!superset->muxnames || !superset->muxnames[0]) {
 			superset++;
 			continue;
 		}
-#endif
-
-#if defined(CONFIG_OMAP_MUX) && defined(CONFIG_DEBUG_FS)
-		if (!superset->muxnames || !superset->muxnames[0]) {
+#else
+		/* Skip pins that are not muxed as GPIO by bootloader */
+		if (!OMAP_MODE_GPIO(omap_mux_read(superset->reg_offset))) {
 			superset++;
 			continue;
 		}

trunk/arch/arm/mm/alignment.c

@@ -11,6 +11,7 @@
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
+#include <linux/moduleparam.h>
 #include <linux/compiler.h>
 #include <linux/kernel.h>
 #include <linux/errno.h>
@@ -77,6 +78,8 @@ static unsigned long ai_dword;
 static unsigned long ai_multi;
 static int ai_usermode;
 
+core_param(alignment, ai_usermode, int, 0600);
+
 #define UM_WARN		(1 << 0)
 #define UM_FIXUP	(1 << 1)
 #define UM_SIGNAL	(1 << 2)

trunk/arch/arm/plat-mxc/Makefile

@@ -13,3 +13,7 @@ obj-$(CONFIG_USB_EHCI_MXC) += ehci.o
 obj-$(CONFIG_MXC_ULPI) += ulpi.o
 obj-$(CONFIG_ARCH_MXC_AUDMUX_V1) += audmux-v1.o
 obj-$(CONFIG_ARCH_MXC_AUDMUX_V2) += audmux-v2.o
+ifdef CONFIG_SND_IMX_SOC
+obj-y += ssi-fiq.o
+obj-y += ssi-fiq-ksym.o
+endif

trunk/arch/arm/plat-mxc/ssi-fiq-ksym.c

@@ -0,0 +1,20 @@
+/*
+ * Exported ksyms for the SSI FIQ handler
+ *
+ * Copyright (C) 2009, Sascha Hauer <s.hauer@pengutronix.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/module.h>
+
+#include <mach/ssi.h>
+
+EXPORT_SYMBOL(imx_ssi_fiq_tx_buffer);
+EXPORT_SYMBOL(imx_ssi_fiq_rx_buffer);
+EXPORT_SYMBOL(imx_ssi_fiq_start);
+EXPORT_SYMBOL(imx_ssi_fiq_end);
+EXPORT_SYMBOL(imx_ssi_fiq_base);
+

trunk/arch/arm/plat-mxc/ssi-fiq.S

@@ -0,0 +1,134 @@
+/*
+ *  Copyright (C) 2009 Sascha Hauer <s.hauer@pengutronix.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/linkage.h>
+#include <asm/assembler.h>
+
+/*
+ * r8  = bit 0-15: tx offset, bit 16-31: tx buffer size
+ * r9  = bit 0-15: rx offset, bit 16-31: rx buffer size
+ */
+
+#define SSI_STX0	0x00
+#define SSI_SRX0	0x08
+#define SSI_SISR	0x14
+#define SSI_SIER	0x18
+#define SSI_SACNT	0x38
+
+#define SSI_SACNT_AC97EN	(1 << 0)
+
+#define SSI_SIER_TFE0_EN	(1 << 0)
+#define SSI_SISR_TFE0		(1 << 0)
+#define SSI_SISR_RFF0		(1 << 2)
+#define SSI_SIER_RFF0_EN	(1 << 2)
+
+		.text
+		.global	imx_ssi_fiq_start
+		.global	imx_ssi_fiq_end
+		.global imx_ssi_fiq_base
+		.global imx_ssi_fiq_rx_buffer
+		.global imx_ssi_fiq_tx_buffer
+
+imx_ssi_fiq_start:
+		ldr r12, imx_ssi_fiq_base
+
+		/* TX */
+		ldr r11, imx_ssi_fiq_tx_buffer
+
+		/* shall we send? */
+		ldr r13, [r12, #SSI_SIER]
+		tst r13, #SSI_SIER_TFE0_EN
+		beq 1f
+
+		/* TX FIFO empty? */
+		ldr r13, [r12, #SSI_SISR]
+		tst r13, #SSI_SISR_TFE0
+		beq 1f
+
+		mov r10, #0x10000
+		sub r10, #1
+		and r10, r10, r8	/* r10: current buffer offset */
+
+		add r11, r11, r10
+
+		ldrh r13, [r11]
+		strh r13, [r12, #SSI_STX0]
+
+		ldrh r13, [r11, #2]
+		strh r13, [r12, #SSI_STX0]
+
+		ldrh r13, [r11, #4]
+		strh r13, [r12, #SSI_STX0]
+
+		ldrh r13, [r11, #6]
+		strh r13, [r12, #SSI_STX0]
+
+		add r10, #8
+		lsr r13, r8, #16	/* r13: buffer size */
+		cmp r10, r13
+		lslgt r8, r13, #16
+		addle r8, #8
+1:
+		/* RX */
+
+		/* shall we receive? */
+		ldr r13, [r12, #SSI_SIER]
+		tst r13, #SSI_SIER_RFF0_EN
+		beq 1f
+
+		/* RX FIFO full? */
+		ldr r13, [r12, #SSI_SISR]
+		tst r13, #SSI_SISR_RFF0
+		beq 1f
+
+		ldr r11, imx_ssi_fiq_rx_buffer
+
+		mov r10, #0x10000
+		sub r10, #1
+		and r10, r10, r9	/* r10: current buffer offset */
+
+		add r11, r11, r10
+
+		ldr r13, [r12, #SSI_SACNT]
+		tst r13, #SSI_SACNT_AC97EN
+
+		ldr r13, [r12, #SSI_SRX0]
+		strh r13, [r11]
+
+		ldr r13, [r12, #SSI_SRX0]
+		strh r13, [r11, #2]
+
+		/* dummy read to skip slot 12 */
+		ldrne r13, [r12, #SSI_SRX0]
+
+		ldr r13, [r12, #SSI_SRX0]
+		strh r13, [r11, #4]
+
+		ldr r13, [r12, #SSI_SRX0]
+		strh r13, [r11, #6]
+
+		/* dummy read to skip slot 12 */
+		ldrne r13, [r12, #SSI_SRX0]
+
+		add r10, #8
+		lsr r13, r9, #16	/* r13: buffer size */
+		cmp r10, r13
+		lslgt r9, r13, #16
+		addle r9, #8
+
+1:
+		@ return from FIQ
+		subs	pc, lr, #4
+imx_ssi_fiq_base:
+		.word 0x0
+imx_ssi_fiq_rx_buffer:
+		.word 0x0
+imx_ssi_fiq_tx_buffer:
+		.word 0x0
+imx_ssi_fiq_end:
+