V4L/DVB (10559): bttv: Fix TDA9880 norm setting code

The code to set the norm for the TDA9880 analog demod was comparing
btv->norm, an index into the bttv driver's norm array, to V4L2_STD_NTSC,
which is a bit flag that's part of the V4L2 API.  This doesn't work of
course and results in the PAL path always being taken.

What's more, it modified the bttv_tvcards[] entries for cards using the
TDA9880.  This is wrong because changing the norm on one card will also
affect other cards of the same type.  Writing to bttv_tvcards is also bad
because it should be read-only or even devinitdata.

Changing the norm would also cause the audio to become unmuted.

Have the code get called for both norm setting and audio input setting
(which where the gpios are set) to avoid needed to modify bttv_tvcards.

Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

drivers/media/video/bt8xx/bttv-cards.c

@@ -4084,27 +4084,26 @@ static void __devinit avermedia_eeprom(struct bttv *btv)
 	       btv->has_remote ? "yes" : "no");
 }
 
-/* used on Voodoo TV/FM (Voodoo 200), S0 wired to 0x10000 */
-void bttv_tda9880_setnorm(struct bttv *btv, unsigned int norm)
+/*
+ * For Voodoo TV/FM and Voodoo 200.  These cards' tuners use a TDA9880
+ * analog demod, which is not I2C controlled like the newer and more common
+ * TDA9887 series.  Instead is has two tri-state input pins, S0 and S1,
+ * that control the IF for the video and audio.  Apparently, bttv GPIO
+ * 0x10000 is connected to S0.  S0 low selects a 38.9 MHz VIF for B/G/D/K/I
+ * (i.e., PAL) while high selects 45.75 MHz for M/N (i.e., NTSC).
+ */
+u32 bttv_tda9880_setnorm(struct bttv *btv, u32 gpiobits)
 {
-	/* fix up our card entry */
-	if(norm==V4L2_STD_NTSC) {
-		bttv_tvcards[BTTV_BOARD_VOODOOTV_FM].gpiomux[TVAUDIO_INPUT_TUNER]=0x957fff;
-		bttv_tvcards[BTTV_BOARD_VOODOOTV_FM].gpiomute=0x957fff;
-		bttv_tvcards[BTTV_BOARD_VOODOOTV_200].gpiomux[TVAUDIO_INPUT_TUNER]=0x957fff;
-		bttv_tvcards[BTTV_BOARD_VOODOOTV_200].gpiomute=0x957fff;
-		dprintk("bttv_tda9880_setnorm to NTSC\n");
-	}
-	else {
-		bttv_tvcards[BTTV_BOARD_VOODOOTV_FM].gpiomux[TVAUDIO_INPUT_TUNER]=0x947fff;
-		bttv_tvcards[BTTV_BOARD_VOODOOTV_FM].gpiomute=0x947fff;
-		bttv_tvcards[BTTV_BOARD_VOODOOTV_200].gpiomux[TVAUDIO_INPUT_TUNER]=0x947fff;
-		bttv_tvcards[BTTV_BOARD_VOODOOTV_200].gpiomute=0x947fff;
-		dprintk("bttv_tda9880_setnorm to PAL\n");
+
+	if (btv->audio == TVAUDIO_INPUT_TUNER) {
+		if (bttv_tvnorms[btv->tvnorm].v4l2_id & V4L2_STD_MN)
+			gpiobits |= 0x10000;
+		else
+			gpiobits &= ~0x10000;
 	}
-	/* set GPIO according */
-	gpio_bits(bttv_tvcards[btv->c.type].gpiomask,
-		  bttv_tvcards[btv->c.type].gpiomux[btv->audio]);
+
+	gpio_bits(bttv_tvcards[btv->c.type].gpiomask, gpiobits);
+	return gpiobits;
 }
 
 

drivers/media/video/bt8xx/bttv-driver.c

@@ -1180,7 +1180,16 @@ audio_mux(struct bttv *btv, int input, int mute)
 	else
 		gpio_val = bttv_tvcards[btv->c.type].gpiomux[input];
 
-	gpio_bits(bttv_tvcards[btv->c.type].gpiomask, gpio_val);
+	switch (btv->c.type) {
+	case BTTV_BOARD_VOODOOTV_FM:
+	case BTTV_BOARD_VOODOOTV_200:
+		gpio_val = bttv_tda9880_setnorm(btv, gpio_val);
+		break;
+
+	default:
+		gpio_bits(bttv_tvcards[btv->c.type].gpiomask, gpio_val);
+	}
+
 	if (bttv_gpio)
 		bttv_gpio_tracking(btv, audio_modes[mute ? 4 : input]);
 	if (in_interrupt())
@@ -1319,7 +1328,7 @@ set_tvnorm(struct bttv *btv, unsigned int norm)
 	switch (btv->c.type) {
 	case BTTV_BOARD_VOODOOTV_FM:
 	case BTTV_BOARD_VOODOOTV_200:
-		bttv_tda9880_setnorm(btv,norm);
+		bttv_tda9880_setnorm(btv, gpio_read());
 		break;
 	}
 	id = tvnorm->v4l2_id;

drivers/media/video/bt8xx/bttv.h

@@ -265,7 +265,7 @@ extern void bttv_init_card2(struct bttv *btv);
 
 /* card-specific funtions */
 extern void tea5757_set_freq(struct bttv *btv, unsigned short freq);
-extern void bttv_tda9880_setnorm(struct bttv *btv, unsigned int norm);
+extern u32 bttv_tda9880_setnorm(struct bttv *btv, u32 gpiobits);
 
 /* extra tweaks for some chipsets */
 extern void bttv_check_chipset(void);