---

yaml
---
r: 308129
b: refs/heads/master
c: 7e6eceb
h: refs/heads/master
i:
  308127: 2df5402
v: v3

[refs]

@@ -1,2 +1,2 @@
 ---
-refs/heads/master: 2b3c83efc9a653af6a24799eeb1a2900ba0439e6
+refs/heads/master: 7e6ecebd2cafd2106f134f55b9d37e7fe5f4f572

trunk/Documentation/ABI/stable/sysfs-driver-usb-usbtmc

@@ -1,5 +1,5 @@
-What:		/sys/bus/usb/drivers/usbtmc/devices/*/interface_capabilities
-What:		/sys/bus/usb/drivers/usbtmc/devices/*/device_capabilities
+What:		/sys/bus/usb/drivers/usbtmc/*/interface_capabilities
+What:		/sys/bus/usb/drivers/usbtmc/*/device_capabilities
 Date:		August 2008
 Contact:	Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 Description:
@@ -12,8 +12,8 @@ Description:
 		The files are read only.
 
 
-What:		/sys/bus/usb/drivers/usbtmc/devices/*/usb488_interface_capabilities
-What:		/sys/bus/usb/drivers/usbtmc/devices/*/usb488_device_capabilities
+What:		/sys/bus/usb/drivers/usbtmc/*/usb488_interface_capabilities
+What:		/sys/bus/usb/drivers/usbtmc/*/usb488_device_capabilities
 Date:		August 2008
 Contact:	Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 Description:
@@ -27,7 +27,7 @@ Description:
 		The files are read only.
 
 
-What:		/sys/bus/usb/drivers/usbtmc/devices/*/TermChar
+What:		/sys/bus/usb/drivers/usbtmc/*/TermChar
 Date:		August 2008
 Contact:	Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 Description:
@@ -40,7 +40,7 @@ Description:
 		sent to the device or not.
 
 
-What:		/sys/bus/usb/drivers/usbtmc/devices/*/TermCharEnabled
+What:		/sys/bus/usb/drivers/usbtmc/*/TermCharEnabled
 Date:		August 2008
 Contact:	Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 Description:
@@ -51,7 +51,7 @@ Description:
 		published by the USB-IF.
 
 
-What:		/sys/bus/usb/drivers/usbtmc/devices/*/auto_abort
+What:		/sys/bus/usb/drivers/usbtmc/*/auto_abort
 Date:		August 2008
 Contact:	Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 Description:

trunk/Documentation/ABI/testing/sysfs-block-rssd

@@ -0,0 +1,18 @@
+What:           /sys/block/rssd*/registers
+Date:           March 2012
+KernelVersion:  3.3
+Contact:        Asai Thambi S P <asamymuthupa@micron.com>
+Description:    This is a read-only file. Dumps below driver information and
+                hardware registers.
+                    - S ACTive
+                    - Command Issue
+                    - Allocated
+                    - Completed
+                    - PORT IRQ STAT
+                    - HOST IRQ STAT
+
+What:           /sys/block/rssd*/status
+Date:           April 2012
+KernelVersion:  3.4
+Contact:        Asai Thambi S P <asamymuthupa@micron.com>
+Description:   This is a read-only file. Indicates the status of the device.

trunk/Documentation/ABI/testing/sysfs-bus-hsi

@@ -0,0 +1,19 @@
+What:		/sys/bus/hsi
+Date:		April 2012
+KernelVersion:	3.4
+Contact:	Carlos Chinea <carlos.chinea@nokia.com>
+Description:
+		High Speed Synchronous Serial Interface (HSI) is a
+		serial interface mainly used for connecting application
+		engines (APE) with cellular modem engines (CMT) in cellular
+		handsets.
+		The bus will be populated with devices (hsi_clients) representing
+		the protocols available in the system. Bus drivers implement
+		those protocols.
+
+What:		/sys/bus/hsi/devices/.../modalias
+Date:		April 2012
+KernelVersion:	3.4
+Contact:	Carlos Chinea <carlos.chinea@nokia.com>
+Description:	Stores the same MODALIAS value emitted by uevent
+		Format: hsi:<hsi_client device name>

trunk/Documentation/ABI/testing/sysfs-cfq-target-latency

@@ -0,0 +1,8 @@
+What:		/sys/block/<device>/iosched/target_latency
+Date:		March 2012
+contact:	Tao Ma <boyu.mt@taobao.com>
+Description:
+		The /sys/block/<device>/iosched/target_latency only exists
+		when the user sets cfq to /sys/block/<device>/scheduler.
+		It contains an estimated latency time for the cfq. cfq will
+		use it to calculate the time slice used for every task.

trunk/Documentation/DocBook/media/v4l/pixfmt-nv12m.xml

@@ -1,6 +1,6 @@
     <refentry id="V4L2-PIX-FMT-NV12M">
       <refmeta>
-	<refentrytitle>V4L2_PIX_FMT_NV12M ('NV12M')</refentrytitle>
+	<refentrytitle>V4L2_PIX_FMT_NV12M ('NM12')</refentrytitle>
 	&manvol;
       </refmeta>
       <refnamediv>

trunk/Documentation/DocBook/media/v4l/pixfmt-yuv420m.xml

@@ -1,6 +1,6 @@
     <refentry id="V4L2-PIX-FMT-YUV420M">
       <refmeta>
-	<refentrytitle>V4L2_PIX_FMT_YUV420M ('YU12M')</refentrytitle>
+	<refentrytitle>V4L2_PIX_FMT_YUV420M ('YM12')</refentrytitle>
 	&manvol;
       </refmeta>
       <refnamediv>

trunk/Documentation/cgroups/memory.txt

@@ -34,8 +34,7 @@ Current Status: linux-2.6.34-mmotm(development version of 2010/April)
 
 Features:
  - accounting anonymous pages, file caches, swap caches usage and limiting them.
- - private LRU and reclaim routine. (system's global LRU and private LRU
-   work independently from each other)
+ - pages are linked to per-memcg LRU exclusively, and there is no global LRU.
  - optionally, memory+swap usage can be accounted and limited.
  - hierarchical accounting
  - soft limit
@@ -154,7 +153,7 @@ updated. page_cgroup has its own LRU on cgroup.
 2.2.1 Accounting details
 
 All mapped anon pages (RSS) and cache pages (Page Cache) are accounted.
-Some pages which are never reclaimable and will not be on the global LRU
+Some pages which are never reclaimable and will not be on the LRU
 are not accounted. We just account pages under usual VM management.
 
 RSS pages are accounted at page_fault unless they've already been accounted

trunk/Documentation/devicetree/bindings/ata/calxeda-sata.txt → trunk/Documentation/devicetree/bindings/ata/ahci-platform.txt

@@ -1,10 +1,10 @@
-* Calxeda SATA Controller
+* AHCI SATA Controller
 
 SATA nodes are defined to describe on-chip Serial ATA controllers.
 Each SATA controller should have its own node.
 
 Required properties:
-- compatible        : compatible list, contains "calxeda,hb-ahci"
+- compatible        : compatible list, contains "calxeda,hb-ahci" or "snps,spear-ahci"
 - interrupts        : <interrupt mapping for SATA IRQ>
 - reg               : <registers mapping>
 
@@ -14,4 +14,3 @@ Example:
                 reg = <0xffe08000 0x1000>;
                 interrupts = <115>;
         };
-

trunk/Documentation/devicetree/bindings/pinctrl/nvidia,tegra20-pinmux.txt

@@ -0,0 +1,132 @@
+NVIDIA Tegra20 pinmux controller
+
+Required properties:
+- compatible: "nvidia,tegra20-pinmux"
+- reg: Should contain the register physical address and length for each of
+  the tri-state, mux, pull-up/down, and pad control register sets.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+Tegra's pin configuration nodes act as a container for an abitrary number of
+subnodes. Each of these subnodes represents some desired configuration for a
+pin, a group, or a list of pins or groups. This configuration can include the
+mux function to select on those pin(s)/group(s), and various pin configuration
+parameters, such as pull-up, tristate, drive strength, etc.
+
+The name of each subnode is not important; all subnodes should be enumerated
+and processed purely based on their content.
+
+Each subnode only affects those parameters that are explicitly listed. In
+other words, a subnode that lists a mux function but no pin configuration
+parameters implies no information about any pin configuration parameters.
+Similarly, a pin subnode that describes a pullup parameter implies no
+information about e.g. the mux function or tristate parameter. For this
+reason, even seemingly boolean values are actually tristates in this binding:
+unspecified, off, or on. Unspecified is represented as an absent property,
+and off/on are represented as integer values 0 and 1.
+
+Required subnode-properties:
+- nvidia,pins : An array of strings. Each string contains the name of a pin or
+    group. Valid values for these names are listed below.
+
+Optional subnode-properties:
+- nvidia,function: A string containing the name of the function to mux to the
+  pin or group. Valid values for function names are listed below. See the Tegra
+  TRM to determine which are valid for each pin or group.
+- nvidia,pull: Integer, representing the pull-down/up to apply to the pin.
+    0: none, 1: down, 2: up.
+- nvidia,tristate: Integer.
+    0: drive, 1: tristate.
+- nvidia,high-speed-mode: Integer. Enable high speed mode the pins.
+    0: no, 1: yes.
+- nvidia,schmitt: Integer. Enables Schmitt Trigger on the input.
+    0: no, 1: yes.
+- nvidia,low-power-mode: Integer. Valid values 0-3. 0 is least power, 3 is
+    most power. Controls the drive power or current. See "Low Power Mode"
+    or "LPMD1" and "LPMD0" in the Tegra TRM.
+- nvidia,pull-down-strength: Integer. Controls drive strength. 0 is weakest.
+    The range of valid values depends on the pingroup. See "CAL_DRVDN" in the
+    Tegra TRM.
+- nvidia,pull-up-strength: Integer. Controls drive strength. 0 is weakest.
+    The range of valid values depends on the pingroup. See "CAL_DRVUP" in the
+    Tegra TRM.
+- nvidia,slew-rate-rising: Integer. Controls rising signal slew rate. 0 is
+    fastest. The range of valid values depends on the pingroup. See
+    "DRVDN_SLWR" in the Tegra TRM.
+- nvidia,slew-rate-falling: Integer. Controls falling signal slew rate. 0 is
+    fastest. The range of valid values depends on the pingroup. See
+    "DRVUP_SLWF" in the Tegra TRM.
+
+Note that many of these properties are only valid for certain specific pins
+or groups. See the Tegra TRM and various pinmux spreadsheets for complete
+details regarding which groups support which functionality. The Linux pinctrl
+driver may also be a useful reference, since it consolidates, disambiguates,
+and corrects data from all those sources.
+
+Valid values for pin and group names are:
+
+  mux groups:
+
+    These all support nvidia,function, nvidia,tristate, and many support
+    nvidia,pull.
+
+    ata, atb, atc, atd, ate, cdev1, cdev2, crtp, csus, dap1, dap2, dap3, dap4,
+    ddc, dta, dtb, dtc, dtd, dte, dtf, gma, gmb, gmc, gmd, gme, gpu, gpu7,
+    gpv, hdint, i2cp, irrx, irtx, kbca, kbcb, kbcc, kbcd, kbce, kbcf, lcsn,
+    ld0, ld1, ld2, ld3, ld4, ld5, ld6, ld7, ld8, ld9, ld10, ld11, ld12, ld13,
+    ld14, ld15, ld16, ld17, ldc, ldi, lhp0, lhp1, lhp2, lhs, lm0, lm1, lpp,
+    lpw0, lpw1, lpw2, lsc0, lsc1, lsck, lsda, lsdi, lspi, lvp0, lvp1, lvs,
+    owc, pmc, pta, rm, sdb, sdc, sdd, sdio1, slxa, slxc, slxd, slxk, spdi,
+    spdo, spia, spib, spic, spid, spie, spif, spig, spih, uaa, uab, uac, uad,
+    uca, ucb, uda.
+
+  tristate groups:
+
+    These only support nvidia,pull.
+
+    ck32, ddrc, pmca, pmcb, pmcc, pmcd, pmce, xm2c, xm2d, ls, lc, ld17_0,
+    ld19_18, ld21_20, ld23_22.
+
+  drive groups:
+
+    With some exceptions, these support nvidia,high-speed-mode,
+    nvidia,schmitt, nvidia,low-power-mode, nvidia,pull-down-strength,
+    nvidia,pull-up-strength, nvidia,slew_rate-rising, nvidia,slew_rate-falling.
+
+    drive_ao1, drive_ao2, drive_at1, drive_at2, drive_cdev1, drive_cdev2,
+    drive_csus, drive_dap1, drive_dap2, drive_dap3, drive_dap4, drive_dbg,
+    drive_lcd1, drive_lcd2, drive_sdmmc2, drive_sdmmc3, drive_spi, drive_uaa,
+    drive_uab, drive_uart2, drive_uart3, drive_vi1, drive_vi2, drive_xm2a,
+    drive_xm2c, drive_xm2d, drive_xm2clk, drive_sdio1, drive_crt, drive_ddc,
+    drive_gma, drive_gmb, drive_gmc, drive_gmd, drive_gme, drive_owr,
+    drive_uda.
+
+Example:
+
+	pinctrl@70000000 {
+		compatible = "nvidia,tegra20-pinmux";
+		reg = < 0x70000014 0x10    /* Tri-state registers */
+			0x70000080 0x20    /* Mux registers */
+			0x700000a0 0x14    /* Pull-up/down registers */
+			0x70000868 0xa8 >; /* Pad control registers */
+	};
+
+Example board file extract:
+
+	pinctrl@70000000 {
+		sdio4_default: sdio4_default {
+			atb {
+				nvidia,pins = "atb", "gma", "gme";
+				nvidia,function = "sdio4";
+				nvidia,pull = <0>;
+				nvidia,tristate = <0>;
+			};
+		};
+	};
+
+	sdhci@c8000600 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&sdio4_default>;
+	};