Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/ker…

…nel/git/arm/arm-soc

Pull ARM SoC fixes from Kevin Hilman:
 "A collection of ARM SoC fixes for v3.14-rc1.

  Mostly a collection of Kconfig, device tree data and compilation fixes
  along with fix to drivers/phy that fixes a boot regression on some
  Marvell mvebu platforms"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  dma: mv_xor: Silence a bunch of LPAE-related warnings
  ARM: ux500: disable msp2 device tree node
  ARM: zynq: Reserve not DMAable space in front of the kernel
  ARM: multi_v7_defconfig: Select CONFIG_SOC_DRA7XX
  ARM: imx6: Initialize low-power mode early again
  ARM: pxa: fix various compilation problems
  ARM: pxa: fix compilation problem on AM300EPD board
  ARM: at91: add Atmel's SAMA5D3 Xplained board
  spi/atmel: document clock properties
  mmc: atmel-mci: document clock properties
  ARM: at91: enable USB host on at91sam9n12ek board
  ARM: at91/dt: fix sama5d3 ohci hclk clock reference
  ARM: at91/dt: sam9263: fix compatibility string for the I2C
  ata: sata_mv: Fix probe failures with optional phys
  drivers: phy: Add support for optional phys
  drivers: phy: Make NULL a valid phy reference
  ARM: fix HAVE_ARM_TWD selection for OMAP and shmobile
  ARM: moxart: move DMA_OF selection to driver
  ARM: hisi: fix kconfig warning on HAVE_ARM_TWD

Documentation/devicetree/bindings/mmc/atmel-hsmci.txt

@@ -13,6 +13,9 @@ Required properties:
 - #address-cells: should be one. The cell is the slot id.
 - #size-cells: should be zero.
 - at least one slot node
+- clock-names: tuple listing input clock names.
+	Required elements: "mci_clk"
+- clocks: phandles to input clocks.
 
 The node contains child nodes for each slot that the platform uses
 
@@ -24,6 +27,8 @@ mmc0: mmc@f0008000 {
 	interrupts = <12 4>;
 	#address-cells = <1>;
 	#size-cells = <0>;
+	clock-names = "mci_clk";
+	clocks = <&mci0_clk>;
 
 	[ child node definitions...]
 };

Documentation/devicetree/bindings/spi/spi_atmel.txt

@@ -5,6 +5,9 @@ Required properties:
 - reg: Address and length of the register set for the device
 - interrupts: Should contain spi interrupt
 - cs-gpios: chipselects
+- clock-names: tuple listing input clock names.
+	Required elements: "spi_clk"
+- clocks: phandles to input clocks.
 
 Example:
 
@@ -14,6 +17,8 @@ spi1: spi@fffcc000 {
 	interrupts = <13 4 5>;
 	#address-cells = <1>;
 	#size-cells = <0>;
+	clocks = <&spi1_clk>;
+	clock-names = "spi_clk";
 	cs-gpios = <&pioB 3 0>;
 	status = "okay";
 

Documentation/phy.txt

@@ -75,14 +75,26 @@ Before the controller can make use of the PHY, it has to get a reference to
 it. This framework provides the following APIs to get a reference to the PHY.
 
 struct phy *phy_get(struct device *dev, const char *string);
+struct phy *phy_optional_get(struct device *dev, const char *string);
 struct phy *devm_phy_get(struct device *dev, const char *string);
-
-phy_get and devm_phy_get can be used to get the PHY. In the case of dt boot,
-the string arguments should contain the phy name as given in the dt data and
-in the case of non-dt boot, it should contain the label of the PHY.
-The only difference between the two APIs is that devm_phy_get associates the
-device with the PHY using devres on successful PHY get. On driver detach,
-release function is invoked on the the devres data and devres data is freed.
+struct phy *devm_phy_optional_get(struct device *dev, const char *string);
+
+phy_get, phy_optional_get, devm_phy_get and devm_phy_optional_get can
+be used to get the PHY. In the case of dt boot, the string arguments
+should contain the phy name as given in the dt data and in the case of
+non-dt boot, it should contain the label of the PHY.  The two
+devm_phy_get associates the device with the PHY using devres on
+successful PHY get. On driver detach, release function is invoked on
+the the devres data and devres data is freed. phy_optional_get and
+devm_phy_optional_get should be used when the phy is optional. These
+two functions will never return -ENODEV, but instead returns NULL when
+the phy cannot be found.
+
+It should be noted that NULL is a valid phy reference. All phy
+consumer calls on the NULL phy become NOPs. That is the release calls,
+the phy_init() and phy_exit() calls, and phy_power_on() and
+phy_power_off() calls are all NOP when applied to a NULL phy. The NULL
+phy is useful in devices for handling optional phy devices.
 
 5. Releasing a reference to the PHY
 

arch/arm/boot/dts/Makefile

@@ -38,6 +38,7 @@ dtb-$(CONFIG_ARCH_AT91) += at91sam9g35ek.dtb
 dtb-$(CONFIG_ARCH_AT91) += at91sam9x25ek.dtb
 dtb-$(CONFIG_ARCH_AT91) += at91sam9x35ek.dtb
 # sama5d3
+dtb-$(CONFIG_ARCH_AT91)	+= at91-sama5d3_xplained.dtb
 dtb-$(CONFIG_ARCH_AT91)	+= sama5d31ek.dtb
 dtb-$(CONFIG_ARCH_AT91)	+= sama5d33ek.dtb
 dtb-$(CONFIG_ARCH_AT91)	+= sama5d34ek.dtb

arch/arm/boot/dts/at91-sama5d3_xplained.dts

@@ -0,0 +1,229 @@
+/*
+ * at91-sama5d3_xplained.dts - Device Tree file for the SAMA5D3 Xplained board
+ *
+ *  Copyright (C) 2014 Atmel,
+ *		  2014 Nicolas Ferre <nicolas.ferre@atmel.com>
+ *
+ * Licensed under GPLv2 or later.
+ */
+/dts-v1/;
+#include "sama5d36.dtsi"
+
+/ {
+	model = "SAMA5D3 Xplained";
+	compatible = "atmel,sama5d3-xplained", "atmel,sama5d3", "atmel,sama5";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	memory {
+		reg = <0x20000000 0x10000000>;
+	};
+
+	ahb {
+		apb {
+			mmc0: mmc@f0000000 {
+				pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 &pinctrl_mmc0_dat4_7 &pinctrl_mmc0_cd>;
+				status = "okay";
+				slot@0 {
+					reg = <0>;
+					bus-width = <8>;
+					cd-gpios = <&pioE 0 GPIO_ACTIVE_LOW>;
+				};
+			};
+
+			spi0: spi@f0004000 {
+				cs-gpios = <&pioD 13 0>;
+				status = "okay";
+			};
+
+			can0: can@f000c000 {
+				status = "okay";
+			};
+
+			i2c0: i2c@f0014000 {
+				status = "okay";
+			};
+
+			i2c1: i2c@f0018000 {
+				status = "okay";
+			};
+
+			macb0: ethernet@f0028000 {
+				phy-mode = "rgmii";
+				status = "okay";
+			};
+
+			usart0: serial@f001c000 {
+				status = "okay";
+			};
+
+			usart1: serial@f0020000 {
+				pinctrl-0 = <&pinctrl_usart1 &pinctrl_usart1_rts_cts>;
+				status = "okay";
+			};
+
+			uart0: serial@f0024000 {
+				status = "okay";
+			};
+
+			mmc1: mmc@f8000000 {
+				pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3 &pinctrl_mmc1_cd>;
+				status = "okay";
+				slot@0 {
+					reg = <0>;
+					bus-width = <4>;
+					cd-gpios = <&pioE 1 GPIO_ACTIVE_HIGH>;
+				};
+			};
+
+			spi1: spi@f8008000 {
+				cs-gpios = <&pioC 25 0>, <0>, <0>, <&pioD 16 0>;
+				status = "okay";
+			};
+
+			adc0: adc@f8018000 {
+				pinctrl-0 = <
+					&pinctrl_adc0_adtrg
+					&pinctrl_adc0_ad0
+					&pinctrl_adc0_ad1
+					&pinctrl_adc0_ad2
+					&pinctrl_adc0_ad3
+					&pinctrl_adc0_ad4
+					&pinctrl_adc0_ad5
+					&pinctrl_adc0_ad6
+					&pinctrl_adc0_ad7
+					&pinctrl_adc0_ad8
+					&pinctrl_adc0_ad9
+					>;
+				status = "okay";
+			};
+
+			i2c2: i2c@f801c000 {
+				dmas = <0>, <0>;	/* Do not use DMA for i2c2 */
+				status = "okay";
+			};
+
+			macb1: ethernet@f802c000 {
+				phy-mode = "rmii";
+				status = "okay";
+			};
+
+			dbgu: serial@ffffee00 {
+				status = "okay";
+			};
+
+			pinctrl@fffff200 {
+				board {
+					pinctrl_mmc0_cd: mmc0_cd {
+						atmel,pins =
+							<AT91_PIOE 0 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
+					};
+
+					pinctrl_mmc1_cd: mmc1_cd {
+						atmel,pins =
+							<AT91_PIOE 1 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
+					};
+
+					pinctrl_usba_vbus: usba_vbus {
+						atmel,pins =
+							<AT91_PIOE 9 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;	/* PE9, conflicts with A9 */
+					};
+				};
+			};
+
+			pmc: pmc@fffffc00 {
+				main: mainck {
+					clock-frequency = <12000000>;
+				};
+			};
+		};
+
+		nand0: nand@60000000 {
+			nand-bus-width = <8>;
+			nand-ecc-mode = "hw";
+			atmel,has-pmecc;
+			atmel,pmecc-cap = <4>;
+			atmel,pmecc-sector-size = <512>;
+			nand-on-flash-bbt;
+			status = "okay";
+
+			at91bootstrap@0 {
+				label = "at91bootstrap";
+				reg = <0x0 0x40000>;
+			};
+
+			bootloader@40000 {
+				label = "bootloader";
+				reg = <0x40000 0x80000>;
+			};
+
+			bootloaderenv@c0000 {
+				label = "bootloader env";
+				reg = <0xc0000 0xc0000>;
+			};
+
+			dtb@180000 {
+				label = "device tree";
+				reg = <0x180000 0x80000>;
+			};
+
+			kernel@200000 {
+				label = "kernel";
+				reg = <0x200000 0x600000>;
+			};
+
+			rootfs@800000 {
+				label = "rootfs";
+				reg = <0x800000 0x0f800000>;
+			};
+		};
+
+		usb0: gadget@00500000 {
+			atmel,vbus-gpio = <&pioE 9 GPIO_ACTIVE_HIGH>;	/* PE9, conflicts with A9 */
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usba_vbus>;
+			status = "okay";
+		};
+
+		usb1: ohci@00600000 {
+			num-ports = <3>;
+			atmel,vbus-gpio = <0
+					   &pioE 3 GPIO_ACTIVE_LOW
+					   &pioE 4 GPIO_ACTIVE_LOW
+					  >;
+			status = "okay";
+		};
+
+		usb2: ehci@00700000 {
+			status = "okay";
+		};
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+
+		bp3 {
+			label = "PB_USER";
+			gpios = <&pioE 29 GPIO_ACTIVE_LOW>;
+			linux,code = <0x104>;
+			gpio-key,wakeup;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		d2 {
+			label = "d2";
+			gpios = <&pioE 23 GPIO_ACTIVE_LOW>;	/* PE23, conflicts with A23, CTS2 */
+			linux,default-trigger = "heartbeat";
+		};
+
+		d3 {
+			label = "d3";
+			gpios = <&pioE 24 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};

arch/arm/boot/dts/at91sam9263.dtsi

@@ -523,7 +523,7 @@
 			};
 
 			i2c0: i2c@fff88000 {
-				compatible = "atmel,at91sam9263-i2c";
+				compatible = "atmel,at91sam9260-i2c";
 				reg = <0xfff88000 0x100>;
 				interrupts = <13 IRQ_TYPE_LEVEL_HIGH 6>;
 				#address-cells = <1>;

arch/arm/boot/dts/at91sam9n12ek.dts

@@ -124,6 +124,10 @@
 			nand-on-flash-bbt;
 			status = "okay";
 		};
+
+		usb0: ohci@00500000 {
+			status = "okay";
+		};
 	};
 
 	leds {

arch/arm/boot/dts/sama5d3.dtsi

@@ -1228,7 +1228,7 @@
 			compatible = "atmel,at91rm9200-ohci", "usb-ohci";
 			reg = <0x00600000 0x100000>;
 			interrupts = <32 IRQ_TYPE_LEVEL_HIGH 2>;
-			clocks = <&usb>, <&uhphs_clk>, <&udphs_clk>,
+			clocks = <&usb>, <&uhphs_clk>, <&uhphs_clk>,
 				 <&uhpck>;
 			clock-names = "usb_clk", "ohci_clk", "hclk", "uhpck";
 			status = "disabled";

arch/arm/boot/dts/ste-href.dtsi

@@ -188,7 +188,6 @@
 		msp2: msp@80117000 {
 			pinctrl-names = "default";
 			pinctrl-0 = <&msp2_default_mode>;
-			status = "okay";
 		};
 
 		msp3: msp@80125000 {

arch/arm/configs/multi_v7_defconfig

@@ -29,6 +29,7 @@ CONFIG_ARCH_OMAP3=y
 CONFIG_ARCH_OMAP4=y
 CONFIG_SOC_OMAP5=y
 CONFIG_SOC_AM33XX=y
+CONFIG_SOC_DRA7XX=y
 CONFIG_SOC_AM43XX=y
 CONFIG_ARCH_ROCKCHIP=y
 CONFIG_ARCH_SOCFPGA=y

arch/arm/mach-hisi/Kconfig

@@ -8,7 +8,7 @@ config ARCH_HI3xxx
 	select CLKSRC_OF
 	select GENERIC_CLOCKEVENTS
 	select HAVE_ARM_SCU
-	select HAVE_ARM_TWD
+	select HAVE_ARM_TWD if SMP
 	select HAVE_SMP
 	select PINCTRL
 	select PINCTRL_SINGLE

arch/arm/mach-imx/clk-imx6q.c

@@ -482,6 +482,9 @@ static void __init imx6q_clocks_init(struct device_node *ccm_node)
 	if (IS_ENABLED(CONFIG_PCI_IMX6))
 		clk_set_parent(clk[lvds1_sel], clk[sata_ref]);
 
+	/* Set initial power mode */
+	imx6q_set_lpm(WAIT_CLOCKED);
+
 	np = of_find_compatible_node(NULL, NULL, "fsl,imx6q-gpt");
 	base = of_iomap(np, 0);
 	WARN_ON(!base);

arch/arm/mach-imx/clk-imx6sl.c

@@ -266,6 +266,9 @@ static void __init imx6sl_clocks_init(struct device_node *ccm_node)
 	/* Audio-related clocks configuration */
 	clk_set_parent(clks[IMX6SL_CLK_SPDIF0_SEL], clks[IMX6SL_CLK_PLL3_PFD3]);
 
+	/* Set initial power mode */
+	imx6q_set_lpm(WAIT_CLOCKED);
+
 	np = of_find_compatible_node(NULL, NULL, "fsl,imx6sl-gpt");
 	base = of_iomap(np, 0);
 	WARN_ON(!base);

arch/arm/mach-imx/pm-imx6q.c

@@ -236,8 +236,6 @@ void __init imx6q_pm_init(void)
 		regmap_update_bits(gpr, IOMUXC_GPR1, IMX6Q_GPR1_GINT,
 				   IMX6Q_GPR1_GINT);
 
-	/* Set initial power mode */
-	imx6q_set_lpm(WAIT_CLOCKED);
 
 	suspend_set_ops(&imx6q_pm_ops);
 }