---

yaml
---
r: 102558
b: refs/heads/master
c: f3ccc08
h: refs/heads/master
v: v3

[refs]

@@ -1,2 +1,2 @@
 ---
-refs/heads/master: 27aaba0ca099461badb496bf7cde5ab5cdc89b98
+refs/heads/master: f3ccc08c8cdeb784087348e67f41a779c787fa0e

trunk/drivers/net/wireless/iwlwifi/iwl-4965.c

@@ -222,6 +222,102 @@ static int iwl4965_load_bsm(struct iwl_priv *priv)
 	return 0;
 }
 
+/**
+ * iwl4965_set_ucode_ptrs - Set uCode address location
+ *
+ * Tell initialization uCode where to find runtime uCode.
+ *
+ * BSM registers initially contain pointers to initialization uCode.
+ * We need to replace them to load runtime uCode inst and data,
+ * and to save runtime data when powering down.
+ */
+static int iwl4965_set_ucode_ptrs(struct iwl_priv *priv)
+{
+	dma_addr_t pinst;
+	dma_addr_t pdata;
+	unsigned long flags;
+	int ret = 0;
+
+	/* bits 35:4 for 4965 */
+	pinst = priv->ucode_code.p_addr >> 4;
+	pdata = priv->ucode_data_backup.p_addr >> 4;
+
+	spin_lock_irqsave(&priv->lock, flags);
+	ret = iwl_grab_nic_access(priv);
+	if (ret) {
+		spin_unlock_irqrestore(&priv->lock, flags);
+		return ret;
+	}
+
+	/* Tell bootstrap uCode where to find image to load */
+	iwl_write_prph(priv, BSM_DRAM_INST_PTR_REG, pinst);
+	iwl_write_prph(priv, BSM_DRAM_DATA_PTR_REG, pdata);
+	iwl_write_prph(priv, BSM_DRAM_DATA_BYTECOUNT_REG,
+				 priv->ucode_data.len);
+
+	/* Inst bytecount must be last to set up, bit 31 signals uCode
+	 *   that all new ptr/size info is in place */
+	iwl_write_prph(priv, BSM_DRAM_INST_BYTECOUNT_REG,
+				 priv->ucode_code.len | BSM_DRAM_INST_LOAD);
+	iwl_release_nic_access(priv);
+
+	spin_unlock_irqrestore(&priv->lock, flags);
+
+	IWL_DEBUG_INFO("Runtime uCode pointers are set.\n");
+
+	return ret;
+}
+
+/**
+ * iwl4965_init_alive_start - Called after REPLY_ALIVE notification received
+ *
+ * Called after REPLY_ALIVE notification received from "initialize" uCode.
+ *
+ * The 4965 "initialize" ALIVE reply contains calibration data for:
+ *   Voltage, temperature, and MIMO tx gain correction, now stored in priv
+ *   (3945 does not contain this data).
+ *
+ * Tell "initialize" uCode to go ahead and load the runtime uCode.
+*/
+static void iwl4965_init_alive_start(struct iwl_priv *priv)
+{
+	/* Check alive response for "valid" sign from uCode */
+	if (priv->card_alive_init.is_valid != UCODE_VALID_OK) {
+		/* We had an error bringing up the hardware, so take it
+		 * all the way back down so we can try again */
+		IWL_DEBUG_INFO("Initialize Alive failed.\n");
+		goto restart;
+	}
+
+	/* Bootstrap uCode has loaded initialize uCode ... verify inst image.
+	 * This is a paranoid check, because we would not have gotten the
+	 * "initialize" alive if code weren't properly loaded.  */
+	if (iwl_verify_ucode(priv)) {
+		/* Runtime instruction load was bad;
+		 * take it all the way back down so we can try again */
+		IWL_DEBUG_INFO("Bad \"initialize\" uCode load.\n");
+		goto restart;
+	}
+
+	/* Calculate temperature */
+	priv->temperature = iwl4965_get_temperature(priv);
+
+	/* Send pointers to protocol/runtime uCode image ... init code will
+	 * load and launch runtime uCode, which will send us another "Alive"
+	 * notification. */
+	IWL_DEBUG_INFO("Initialization Alive received.\n");
+	if (iwl4965_set_ucode_ptrs(priv)) {
+		/* Runtime instruction load won't happen;
+		 * take it all the way back down so we can try again */
+		IWL_DEBUG_INFO("Couldn't set up uCode pointers.\n");
+		goto restart;
+	}
+	return;
+
+restart:
+	queue_work(priv->workqueue, &priv->restart);
+}
+
 static int is_fat_channel(__le32 rxon_flags)
 {
 	return (rxon_flags & RXON_FLG_CHANNEL_MODE_PURE_40_MSK) ||
@@ -3724,6 +3820,7 @@ static struct iwl_lib_ops iwl4965_lib = {
 	.rx_handler_setup = iwl4965_rx_handler_setup,
 	.is_valid_rtc_data_addr = iwl4965_hw_valid_rtc_data_addr,
 	.alive_notify = iwl4965_alive_notify,
+	.init_alive_start = iwl4965_init_alive_start,
 	.load_ucode = iwl4965_load_bsm,
 	.apm_ops = {
 		.init = iwl4965_apm_init,

trunk/drivers/net/wireless/iwlwifi/iwl-core.h

@@ -110,6 +110,8 @@ struct iwl_lib_ops {
 	void (*rx_handler_setup)(struct iwl_priv *priv);
 	/* nic Tx fifo handling */
 	int (*disable_tx_fifo)(struct iwl_priv *priv);
+	/* alive notification after init uCode load */
+	void (*init_alive_start)(struct iwl_priv *priv);
 	/* alive notification */
 	int (*alive_notify)(struct iwl_priv *priv);
 	/* check validity of rtc data address */

trunk/drivers/net/wireless/iwlwifi/iwl4965-base.c

@@ -4162,105 +4162,6 @@ static int iwl4965_read_ucode(struct iwl_priv *priv)
 	return ret;
 }
 
-
-/**
- * iwl4965_set_ucode_ptrs - Set uCode address location
- *
- * Tell initialization uCode where to find runtime uCode.
- *
- * BSM registers initially contain pointers to initialization uCode.
- * We need to replace them to load runtime uCode inst and data,
- * and to save runtime data when powering down.
- */
-static int iwl4965_set_ucode_ptrs(struct iwl_priv *priv)
-{
-	dma_addr_t pinst;
-	dma_addr_t pdata;
-	int rc = 0;
-	unsigned long flags;
-
-	/* bits 35:4 for 4965 */
-	pinst = priv->ucode_code.p_addr >> 4;
-	pdata = priv->ucode_data_backup.p_addr >> 4;
-
-	spin_lock_irqsave(&priv->lock, flags);
-	rc = iwl_grab_nic_access(priv);
-	if (rc) {
-		spin_unlock_irqrestore(&priv->lock, flags);
-		return rc;
-	}
-
-	/* Tell bootstrap uCode where to find image to load */
-	iwl_write_prph(priv, BSM_DRAM_INST_PTR_REG, pinst);
-	iwl_write_prph(priv, BSM_DRAM_DATA_PTR_REG, pdata);
-	iwl_write_prph(priv, BSM_DRAM_DATA_BYTECOUNT_REG,
-				 priv->ucode_data.len);
-
-	/* Inst bytecount must be last to set up, bit 31 signals uCode
-	 *   that all new ptr/size info is in place */
-	iwl_write_prph(priv, BSM_DRAM_INST_BYTECOUNT_REG,
-				 priv->ucode_code.len | BSM_DRAM_INST_LOAD);
-
-	iwl_release_nic_access(priv);
-
-	spin_unlock_irqrestore(&priv->lock, flags);
-
-	IWL_DEBUG_INFO("Runtime uCode pointers are set.\n");
-
-	return rc;
-}
-
-/**
- * iwl4965_init_alive_start - Called after REPLY_ALIVE notification received
- *
- * Called after REPLY_ALIVE notification received from "initialize" uCode.
- *
- * The 4965 "initialize" ALIVE reply contains calibration data for:
- *   Voltage, temperature, and MIMO tx gain correction, now stored in priv
- *   (3945 does not contain this data).
- *
- * Tell "initialize" uCode to go ahead and load the runtime uCode.
-*/
-static void iwl4965_init_alive_start(struct iwl_priv *priv)
-{
-	/* Check alive response for "valid" sign from uCode */
-	if (priv->card_alive_init.is_valid != UCODE_VALID_OK) {
-		/* We had an error bringing up the hardware, so take it
-		 * all the way back down so we can try again */
-		IWL_DEBUG_INFO("Initialize Alive failed.\n");
-		goto restart;
-	}
-
-	/* Bootstrap uCode has loaded initialize uCode ... verify inst image.
-	 * This is a paranoid check, because we would not have gotten the
-	 * "initialize" alive if code weren't properly loaded.  */
-	if (iwl_verify_ucode(priv)) {
-		/* Runtime instruction load was bad;
-		 * take it all the way back down so we can try again */
-		IWL_DEBUG_INFO("Bad \"initialize\" uCode load.\n");
-		goto restart;
-	}
-
-	/* Calculate temperature */
-	priv->temperature = iwl4965_get_temperature(priv);
-
-	/* Send pointers to protocol/runtime uCode image ... init code will
-	 * load and launch runtime uCode, which will send us another "Alive"
-	 * notification. */
-	IWL_DEBUG_INFO("Initialization Alive received.\n");
-	if (iwl4965_set_ucode_ptrs(priv)) {
-		/* Runtime instruction load won't happen;
-		 * take it all the way back down so we can try again */
-		IWL_DEBUG_INFO("Couldn't set up uCode pointers.\n");
-		goto restart;
-	}
-	return;
-
- restart:
-	queue_work(priv->workqueue, &priv->restart);
-}
-
-
 /**
  * iwl4965_alive_start - called after REPLY_ALIVE notification received
  *                   from protocol/runtime uCode (initialization uCode's
@@ -4586,7 +4487,7 @@ static void iwl4965_bg_init_alive_start(struct work_struct *data)
 		return;
 
 	mutex_lock(&priv->mutex);
-	iwl4965_init_alive_start(priv);
+	priv->cfg->ops->lib->init_alive_start(priv);
 	mutex_unlock(&priv->mutex);
 }