Merge tag 'regulator-3.9' of git://git.kernel.org/pub/scm/linux/kerne…

…l/git/broonie/regulator

Pull regulator updates from Mark Brown:
 "A fairly quiet release for the regulator API, the bulk of the changes
  being lots of small cleanups and API updates contributed by Axel Lin
  with just a small set of larger changes:

   - New driver for LP8755

   - DT support for S5M8767, TPS51632, TPS6507x and TPS65090

   - Support for writing a "commit changes" bit in the regmap helper
     functions."

* tag 'regulator-3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (60 commits)
  regulator: Fix memory garbage dev_err printout.
  regulator: max77686: Reuse rdev_get_id() function.
  regulator: tps51632: Use regulator_[get|set]_voltage_sel_regmap
  regulator: as3711: Fix checking if no platform initialization data
  regulator: s5m8767: Prevent possible NULL pointer dereference
  regulator: s5m8767: Fix dev argument for devm_kzalloc and of_get_regulator_init_data
  regulator: core: Optimize _regulator_do_set_voltage if voltage does not change
  regulator: max8998: Let regulator core handle the case selector == old_selector
  regulator: s5m8767: Use of_get_child_count()
  regulator: anatop: improve precision of delay time
  regulator: show state for GPIO-controlled regulators
  regulator: s5m8767: Fix build in non-DT case
  regulator: add device tree support for s5m8767
  regulator: palmas: Remove a redundant setting for warm_reset
  regulator: mc13xxx: Use of_get_child_count()
  regulator: max8997: Use of_get_child_count()
  regulator: tps65090: Fix using wrong dev argument for calling of_regulator_match
  regulators: anatop: add set_voltage_time_sel interface
  regulator: Add missing of_node_put()
  regulator: tps6507x: Fix using wrong dev argument for calling of_regulator_match
  ...

Documentation/devicetree/bindings/mfd/tps6507x.txt

@@ -0,0 +1,91 @@
+TPS6507x Power Management Integrated Circuit
+
+Required properties:
+- compatible: "ti,tps6507x"
+- reg: I2C slave address
+- regulators: This is the list of child nodes that specify the regulator
+  initialization data for defined regulators. Not all regulators for the
+  given device need to be present. The definition for each of these nodes
+  is defined using the standard binding for regulators found at
+  Documentation/devicetree/bindings/regulator/regulator.txt.
+  The regulator is matched with the regulator-compatible.
+
+  The valid regulator-compatible values are:
+  tps6507x: vdcdc1, vdcdc2, vdcdc3, vldo1, vldo2
+- xxx-supply: Input voltage supply regulator.
+  These entries are required if regulators are enabled for a device.
+  Missing of these properties can cause the regulator registration
+  fails.
+  If some of input supply is powered through battery or always-on
+  supply then also it is require to have these parameters with proper
+  node handle of always on power supply.
+  tps6507x:
+       vindcdc1_2-supply: VDCDC1 and VDCDC2 input.
+       vindcdc3-supply  : VDCDC3 input.
+       vldo1_2-supply   : VLDO1 and VLDO2 input.
+
+Regulator Optional properties:
+- defdcdc_default: It's property of DCDC2 and DCDC3 regulators.
+			0: If defdcdc pin of DCDC2/DCDC3 is pulled to GND.
+			1: If defdcdc pin of DCDC2/DCDC3 is driven HIGH.
+  If this property is not defined, it defaults to 0 (not enabled).
+
+Example:
+
+	pmu: tps6507x@48 {
+		compatible = "ti,tps6507x";
+		reg = <0x48>;
+
+		vindcdc1_2-supply = <&vbat>;
+		vindcdc3-supply = <...>;
+		vinldo1_2-supply = <...>;
+
+		regulators {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			vdcdc1_reg: regulator@0 {
+				regulator-compatible = "VDCDC1";
+				reg = <0>;
+				regulator-min-microvolt = <3150000>;
+				regulator-max-microvolt = <3450000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+			vdcdc2_reg: regulator@1 {
+				regulator-compatible = "VDCDC2";
+				reg = <1>;
+				regulator-min-microvolt = <1710000>;
+				regulator-max-microvolt = <3450000>;
+				regulator-always-on;
+				regulator-boot-on;
+				defdcdc_default = <1>;
+			};
+			vdcdc3_reg: regulator@2 {
+				regulator-compatible = "VDCDC3";
+				reg = <2>;
+				regulator-min-microvolt = <950000>
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-boot-on;
+				defdcdc_default = <1>;
+			};
+			ldo1_reg: regulator@3 {
+				regulator-compatible = "LDO1";
+				reg = <3>;
+				regulator-min-microvolt = <1710000>;
+				regulator-max-microvolt = <1890000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+			ldo2_reg: regulator@4 {
+				regulator-compatible = "LDO2";
+				reg = <4>;
+				regulator-min-microvolt = <1140000>;
+				regulator-max-microvolt = <1320000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+		};
+
+	};

Documentation/devicetree/bindings/regulator/anatop-regulator.txt

@@ -9,6 +9,11 @@ Required properties:
 - anatop-min-voltage: Minimum voltage of this regulator
 - anatop-max-voltage: Maximum voltage of this regulator
 
+Optional properties:
+- anatop-delay-reg-offset: Anatop MFD step time register offset
+- anatop-delay-bit-shift: Bit shift for the step time register
+- anatop-delay-bit-width: Number of bits used in the step time register
+
 Any property defined as part of the core regulator
 binding, defined in regulator.txt, can also be used.
 
@@ -23,6 +28,9 @@ Example:
 		anatop-reg-offset = <0x140>;
 		anatop-vol-bit-shift = <9>;
 		anatop-vol-bit-width = <5>;
+		anatop-delay-reg-offset = <0x170>;
+		anatop-delay-bit-shift = <24>;
+		anatop-delay-bit-width = <2>;
 		anatop-min-bit-val = <1>;
 		anatop-min-voltage = <725000>;
 		anatop-max-voltage = <1300000>;

Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt

@@ -0,0 +1,152 @@
+* Samsung S5M8767 Voltage and Current Regulator
+
+The Samsung S5M8767 is a multi-function device which includes volatage and
+current regulators, rtc, charger controller and other sub-blocks. It is
+interfaced to the host controller using a i2c interface. Each sub-block is
+addressed by the host system using different i2c slave address. This document
+describes the bindings for 'pmic' sub-block of s5m8767.
+
+Required properties:
+- compatible: Should be "samsung,s5m8767-pmic".
+- reg: Specifies the i2c slave address of the pmic block. It should be 0x66.
+
+- s5m8767,pmic-buck2-dvs-voltage: A set of 8 voltage values in micro-volt (uV)
+  units for buck2 when changing voltage using gpio dvs. Refer to [1] below
+  for additional information.
+
+- s5m8767,pmic-buck3-dvs-voltage: A set of 8 voltage values in micro-volt (uV)
+  units for buck3 when changing voltage using gpio dvs. Refer to [1] below
+  for additional information.
+
+- s5m8767,pmic-buck4-dvs-voltage: A set of 8 voltage values in micro-volt (uV)
+  units for buck4 when changing voltage using gpio dvs. Refer to [1] below
+  for additional information.
+
+- s5m8767,pmic-buck-ds-gpios: GPIO specifiers for three host gpio's used
+  for selecting GPIO DVS lines. It is one-to-one mapped to dvs gpio lines.
+
+[1] If none of the 's5m8767,pmic-buck[2/3/4]-uses-gpio-dvs' optional
+    property is specified, the 's5m8767,pmic-buck[2/3/4]-dvs-voltage'
+    property should specify atleast one voltage level (which would be a
+    safe operating voltage).
+
+    If either of the 's5m8767,pmic-buck[2/3/4]-uses-gpio-dvs' optional
+    property is specified, then all the eight voltage values for the
+    's5m8767,pmic-buck[2/3/4]-dvs-voltage' should be specified.
+
+Optional properties:
+- interrupt-parent: Specifies the phandle of the interrupt controller to which
+  the interrupts from s5m8767 are delivered to.
+- interrupts: Interrupt specifiers for two interrupt sources.
+  - First interrupt specifier is for 'irq1' interrupt.
+  - Second interrupt specifier is for 'alert' interrupt.
+- s5m8767,pmic-buck2-uses-gpio-dvs: 'buck2' can be controlled by gpio dvs.
+- s5m8767,pmic-buck3-uses-gpio-dvs: 'buck3' can be controlled by gpio dvs.
+- s5m8767,pmic-buck4-uses-gpio-dvs: 'buck4' can be controlled by gpio dvs.
+
+Additional properties required if either of the optional properties are used:
+
+- s5m8767,pmic-buck234-default-dvs-idx: Default voltage setting selected from
+  the possible 8 options selectable by the dvs gpios. The value of this
+  property should be between 0 and 7. If not specified or if out of range, the
+  default value of this property is set to 0.
+
+- s5m8767,pmic-buck-dvs-gpios: GPIO specifiers for three host gpio's used
+  for dvs. The format of the gpio specifier depends in the gpio controller.
+
+Regulators: The regulators of s5m8767 that have to be instantiated should be
+included in a sub-node named 'regulators'. Regulator nodes included in this
+sub-node should be of the format as listed below.
+
+	regulator_name {
+		ldo1_reg: LDO1 {
+			regulator-name = "VDD_ALIVE_1.0V";
+			regulator-min-microvolt = <1100000>;
+			regulator-max-microvolt = <1100000>;
+			regulator-always-on;
+			regulator-boot-on;
+			op_mode = <1>; /* Normal Mode */
+		};
+	};
+The above regulator entries are defined in regulator bindings documentation
+except op_mode description.
+	- op_mode: describes the different operating modes of the LDO's with
+		power mode change in SOC. The different possible values are,
+		0 - always off mode
+		1 - on in normal mode
+		2 - low power mode
+		3 - suspend mode
+
+The following are the names of the regulators that the s5m8767 pmic block
+supports. Note: The 'n' in LDOn and BUCKn represents the LDO or BUCK number
+as per the datasheet of s5m8767.
+
+	- LDOn
+		  - valid values for n are 1 to 28
+		  - Example: LDO0, LD01, LDO28
+	- BUCKn
+		  - valid values for n are 1 to 9.
+		  - Example: BUCK1, BUCK2, BUCK9
+
+The bindings inside the regulator nodes use the standard regulator bindings
+which are documented elsewhere.
+
+Example:
+
+	s5m8767_pmic@66 {
+		compatible = "samsung,s5m8767-pmic";
+		reg = <0x66>;
+
+		s5m8767,pmic-buck2-uses-gpio-dvs;
+		s5m8767,pmic-buck3-uses-gpio-dvs;
+		s5m8767,pmic-buck4-uses-gpio-dvs;
+
+		s5m8767,pmic-buck-default-dvs-idx = <0>;
+
+		s5m8767,pmic-buck-dvs-gpios = <&gpx0 0 1 0 0>, /* DVS1 */
+						 <&gpx0 1 1 0 0>, /* DVS2 */
+						 <&gpx0 2 1 0 0>; /* DVS3 */
+
+		s5m8767,pmic-buck-ds-gpios = <&gpx2 3 1 0 0>, /* SET1 */
+						<&gpx2 4 1 0 0>, /* SET2 */
+						<&gpx2 5 1 0 0>; /* SET3 */
+
+		s5m8767,pmic-buck2-dvs-voltage = <1350000>, <1300000>,
+						 <1250000>, <1200000>,
+						 <1150000>, <1100000>,
+						 <1000000>, <950000>;
+
+		s5m8767,pmic-buck3-dvs-voltage = <1100000>, <1100000>,
+						 <1100000>, <1100000>,
+						 <1000000>, <1000000>,
+						 <1000000>, <1000000>;
+
+		s5m8767,pmic-buck4-dvs-voltage = <1200000>, <1200000>,
+						 <1200000>, <1200000>,
+						 <1200000>, <1200000>,
+						 <1200000>, <1200000>;
+
+		regulators {
+			ldo1_reg: LDO1 {
+				regulator-name = "VDD_ABB_3.3V";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				op_mode = <1>; /* Normal Mode */
+			};
+
+			ldo2_reg: LDO2 {
+				regulator-name = "VDD_ALIVE_1.1V";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-always-on;
+			};
+
+			buck1_reg: BUCK1 {
+				regulator-name = "VDD_MIF_1.2V";
+				regulator-min-microvolt = <950000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+		};
+	};

Documentation/devicetree/bindings/regulator/tps51632-regulator.txt

@@ -0,0 +1,27 @@
+TPS51632 Voltage regulators
+
+Required properties:
+- compatible: Must be "ti,tps51632"
+- reg: I2C slave address
+
+Optional properties:
+- ti,enable-pwm-dvfs: Enable the DVFS voltage control through the PWM interface.
+- ti,dvfs-step-20mV: The 20mV step voltage when PWM DVFS enabled. Missing this
+	will set 10mV step voltage in PWM DVFS mode. In normal mode, the voltage
+	step is 10mV as per datasheet.
+
+Any property defined as part of the core regulator binding, defined in
+regulator.txt, can also be used.
+
+Example:
+
+	tps51632 {
+		compatible = "ti,tps51632";
+		reg =  <0x43>;
+		regulator-name = "tps51632-vout";
+		regulator-min-microvolt = <500000>;
+		regulator-max-microvolt = <1500000>;
+		regulator-boot-on;
+		ti,enable-pwm-dvfs;
+		ti,dvfs-step-20mV;
+	};