---

yaml
---
r: 349321
b: refs/heads/master
c: f94d4fe
h: refs/heads/master
i:
  349319: df82305
v: v3

[refs]

@@ -1,2 +1,2 @@
 ---
-refs/heads/master: 55ebbb59c1c6eb1b040f62b8c4ae0b724de6e55a
+refs/heads/master: f94d4fe0b5bbe8385245a1d9ef11d785c05df0da

trunk/Documentation/devicetree/bindings/clock/imx23-clock.txt

@@ -60,11 +60,6 @@ clks: clkctrl@80040000 {
 	compatible = "fsl,imx23-clkctrl";
 	reg = <0x80040000 0x2000>;
 	#clock-cells = <1>;
-	clock-output-names =
-		...
-		"uart",		/* 32 */
-		...
-		"end_of_list";
 };
 
 auart0: serial@8006c000 {

trunk/Documentation/devicetree/bindings/clock/imx25-clock.txt

@@ -146,10 +146,6 @@ clks: ccm@53f80000 {
 	compatible = "fsl,imx25-ccm";
 	reg = <0x53f80000 0x4000>;
 	interrupts = <31>;
-	clock-output-names = ...
-			"uart_ipg",
-			"uart_serial",
-			...;
 };
 
 uart1: serial@43f90000 {

trunk/Documentation/devicetree/bindings/clock/imx28-clock.txt

@@ -83,11 +83,6 @@ clks: clkctrl@80040000 {
 	compatible = "fsl,imx28-clkctrl";
 	reg = <0x80040000 0x2000>;
 	#clock-cells = <1>;
-	clock-output-names =
-		...
-		"uart",		/* 45 */
-		...
-		"end_of_list";
 };
 
 auart0: serial@8006a000 {

trunk/Documentation/devicetree/bindings/clock/imx6q-clock.txt

@@ -211,10 +211,6 @@ clks: ccm@020c4000 {
 	reg = <0x020c4000 0x4000>;
 	interrupts = <0 87 0x04 0 88 0x04>;
 	#clock-cells = <1>;
-	clock-output-names = ...
-			     "uart_ipg",
-			     "uart_serial",
-			     ...;
 };
 
 uart1: serial@02020000 {

trunk/Documentation/devicetree/bindings/gpio/gpio-poweroff.txt

@@ -1,4 +1,19 @@
-GPIO line that should be set high/low to power off a device
+Driver a GPIO line that can be used to turn the power off.
+
+The driver supports both level triggered and edge triggered power off.
+At driver load time, the driver will request the given gpio line and
+install a pm_power_off handler. If the optional properties 'input' is
+not found, the GPIO line will be driven in the inactive
+state. Otherwise its configured as an input.
+
+When the pm_power_off is called, the gpio is configured as an output,
+and drive active, so triggering a level triggered power off
+condition. This will also cause an inactive->active edge condition, so
+triggering positive edge triggered power off. After a delay of 100ms,
+the GPIO is set to inactive, thus causing an active->inactive edge,
+triggering negative edge triggered power off. After another 100ms
+delay the GPIO is driver active again. If the power is still on and
+the CPU still running after a 3000ms delay, a WARN_ON(1) is emitted.
 
 Required properties:
 - compatible : should be "gpio-poweroff".
@@ -13,10 +28,9 @@ Optional properties:
   property is not specified, the GPIO is initialized as an output in its
   inactive state.
 
-
 Examples:
 
 gpio-poweroff {
 	compatible = "gpio-poweroff";
-	gpios = <&gpio 4 0>; /* GPIO 4 Active Low */
+	gpios = <&gpio 4 0>;
 };

trunk/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt

@@ -81,7 +81,8 @@ PA31	TXD4
 Required properties for pin configuration node:
 - atmel,pins: 4 integers array, represents a group of pins mux and config
   setting. The format is atmel,pins = <PIN_BANK PIN_BANK_NUM PERIPH CONFIG>.
-  The PERIPH 0 means gpio.
+  The PERIPH 0 means gpio, PERIPH 1 is periph A, PERIPH 2 is periph B...
+  PIN_BANK 0 is pioA, PIN_BANK 1 is pioB...
 
 Bits used for CONFIG:
 PULL_UP		(1 << 0): indicate this pin need a pull up.
@@ -126,7 +127,7 @@ pinctrl@fffff400 {
 		pinctrl_dbgu: dbgu-0 {
 			atmel,pins =
 				<1 14 0x1 0x0	/* PB14 periph A */
-				 1 15 0x1 0x1>;	/* PB15 periph with pullup */
+				 1 15 0x1 0x1>;	/* PB15 periph A with pullup */
 		};
 	};
 };

trunk/Documentation/filesystems/f2fs.txt

@@ -175,9 +175,9 @@ consists of multiple segments as described below.
                                             align with the zone size <-|
                  |-> align with the segment size
      _________________________________________________________________________
-    |            |            |    Node     |   Segment   |   Segment  |      |
-    | Superblock | Checkpoint |   Address   |    Info.    |   Summary  | Main |
-    |    (SB)    |   (CP)     | Table (NAT) | Table (SIT) | Area (SSA) |      |
+    |            |            |   Segment   |    Node     |   Segment  |      |
+    | Superblock | Checkpoint |    Info.    |   Address   |   Summary  | Main |
+    |    (SB)    |   (CP)     | Table (SIT) | Table (NAT) | Area (SSA) |      |
     |____________|_____2______|______N______|______N______|______N_____|__N___|
                                                                        .      .
                                                              .                .
@@ -200,14 +200,14 @@ consists of multiple segments as described below.
  : It contains file system information, bitmaps for valid NAT/SIT sets, orphan
    inode lists, and summary entries of current active segments.
 
-- Node Address Table (NAT)
- : It is composed of a block address table for all the node blocks stored in
-   Main area.
-
 - Segment Information Table (SIT)
  : It contains segment information such as valid block count and bitmap for the
    validity of all the blocks.
 
+- Node Address Table (NAT)
+ : It is composed of a block address table for all the node blocks stored in
+   Main area.
+
 - Segment Summary Area (SSA)
  : It contains summary entries which contains the owner information of all the
    data and node blocks stored in Main area.
@@ -236,13 +236,13 @@ For file system consistency, each CP points to which NAT and SIT copies are
 valid, as shown as below.
 
   +--------+----------+---------+
-  |   CP   |    NAT   |   SIT   |
+  |   CP   |    SIT   |   NAT   |
   +--------+----------+---------+
   .         .          .          .
   .            .              .              .
   .               .                 .                 .
   +-------+-------+--------+--------+--------+--------+
-  | CP #0 | CP #1 | NAT #0 | NAT #1 | SIT #0 | SIT #1 |
+  | CP #0 | CP #1 | SIT #0 | SIT #1 | NAT #0 | NAT #1 |
   +-------+-------+--------+--------+--------+--------+
      |             ^                          ^
      |             |                          |

trunk/Documentation/networking/ip-sysctl.txt

@@ -36,7 +36,7 @@ neigh/default/unres_qlen_bytes - INTEGER
 	The maximum number of bytes which may be used by packets
 	queued for each	unresolved address by other network layers.
 	(added in linux 3.3)
-	Seting negative value is meaningless and will retrun error.
+	Setting negative value is meaningless and will return error.
 	Default: 65536 Bytes(64KB)
 
 neigh/default/unres_qlen - INTEGER
@@ -215,7 +215,7 @@ tcp_ecn - INTEGER
 	Possible values are:
 		0 Disable ECN.  Neither initiate nor accept ECN.
 		1 Always request ECN on outgoing connection attempts.
-		2 Enable ECN when requested by incomming connections
+		2 Enable ECN when requested by incoming connections
 		  but do not request ECN on outgoing connections.
 	Default: 2
 
@@ -503,7 +503,7 @@ tcp_fastopen - INTEGER
 tcp_syn_retries - INTEGER
 	Number of times initial SYNs for an active TCP connection attempt
 	will be retransmitted. Should not be higher than 255. Default value
-	is 6, which corresponds to 63seconds till the last restransmission
+	is 6, which corresponds to 63seconds till the last retransmission
 	with the current initial RTO of 1second. With this the final timeout
 	for an active TCP connection attempt will happen after 127seconds.
 
@@ -1331,6 +1331,12 @@ force_tllao - BOOLEAN
 	race condition where the sender deletes the cached link-layer address
 	prior to receiving a response to a previous solicitation."
 
+ndisc_notify - BOOLEAN
+	Define mode for notification of address and device changes.
+	0 - (default): do nothing
+	1 - Generate unsolicited neighbour advertisements when device is brought
+	    up or hardware address changes.
+
 icmp/*:
 ratelimit - INTEGER
 	Limit the maximal rates for sending ICMPv6 packets.
@@ -1530,7 +1536,7 @@ cookie_hmac_alg - STRING
 	* sha1
 	* none
 	Ability to assign md5 or sha1 as the selected alg is predicated on the
-	configuarion of those algorithms at build time (CONFIG_CRYPTO_MD5 and
+	configuration of those algorithms at build time (CONFIG_CRYPTO_MD5 and
 	CONFIG_CRYPTO_SHA1).
 
 	Default: Dependent on configuration.  MD5 if available, else SHA1 if
@@ -1548,7 +1554,7 @@ rcvbuf_policy - INTEGER
 	blocking.
 
 	1: rcvbuf space is per association
-	0: recbuf space is per socket
+	0: rcvbuf space is per socket
 
 	Default: 0
 

trunk/Documentation/power/runtime_pm.txt

@@ -642,12 +642,13 @@ out the following operations:
   * During system suspend it calls pm_runtime_get_noresume() and
     pm_runtime_barrier() for every device right before executing the
     subsystem-level .suspend() callback for it.  In addition to that it calls
-    pm_runtime_disable() for every device right after executing the
-    subsystem-level .suspend() callback for it.
+    __pm_runtime_disable() with 'false' as the second argument for every device
+    right before executing the subsystem-level .suspend_late() callback for it.
 
   * During system resume it calls pm_runtime_enable() and pm_runtime_put_sync()
-    for every device right before and right after executing the subsystem-level
-    .resume() callback for it, respectively.
+    for every device right after executing the subsystem-level .resume_early()
+    callback and right after executing the subsystem-level .resume() callback
+    for it, respectively.
 
 7. Generic subsystem callbacks
 

trunk/Documentation/sysctl/kernel.txt

@@ -38,6 +38,7 @@ show up in /proc/sys/kernel:
 - l2cr                        [ PPC only ]
 - modprobe                    ==> Documentation/debugging-modules.txt
 - modules_disabled
+- msg_next_id		      [ sysv ipc ]
 - msgmax
 - msgmnb
 - msgmni
@@ -62,7 +63,9 @@ show up in /proc/sys/kernel:
 - rtsig-max
 - rtsig-nr
 - sem
+- sem_next_id		      [ sysv ipc ]
 - sg-big-buff                 [ generic SCSI device (sg) ]
+- shm_next_id		      [ sysv ipc ]
 - shm_rmid_forced
 - shmall
 - shmmax                      [ sysv ipc ]
@@ -320,6 +323,22 @@ to false.
 
 ==============================================================
 
+msg_next_id, sem_next_id, and shm_next_id:
+
+These three toggles allows to specify desired id for next allocated IPC
+object: message, semaphore or shared memory respectively.
+
+By default they are equal to -1, which means generic allocation logic.
+Possible values to set are in range {0..INT_MAX}.
+
+Notes:
+1) kernel doesn't guarantee, that new object will have desired id. So,
+it's up to userspace, how to handle an object with "wrong" id.
+2) Toggle with non-default value will be set back to -1 by kernel after
+successful IPC object allocation.
+
+==============================================================
+
 nmi_watchdog:
 
 Enables/Disables the NMI watchdog on x86 systems. When the value is
@@ -542,6 +561,19 @@ are doing anyway :)
 
 ==============================================================
 
+shmall:
+
+This parameter sets the total amount of shared memory pages that
+can be used system wide. Hence, SHMALL should always be at least
+ceil(shmmax/PAGE_SIZE).
+
+If you are not sure what the default PAGE_SIZE is on your Linux
+system, you can run the following command:
+
+# getconf PAGE_SIZE
+
+==============================================================
+
 shmmax:
 
 This value can be used to query and set the run time limit