spi/fsl_spi: add eSPI controller support

Add eSPI controller support based on the library code spi_fsl_lib.c.

The eSPI controller is newer controller 85xx/Pxxx devices supported.
There're some differences comparing to the SPI controller:

1. Has different register map and different bit definition
   So leave the code operated the register to the driver code, not
   the common code.

2. Support 4 dedicated chip selects
   The software can't controll the chip selects directly, The SPCOM[CS]
   field is used to select which chip selects is used, and the
   SPCOM[TRANLEN] field is set to tell the controller how long the CS
   signal need to be asserted. So the driver doesn't need the chipselect
   related function when transfering data, just set corresponding register
   fields to controll the chipseclect.

3. Different Transmit/Receive FIFO access register behavior
   For SPI controller, the Tx/Rx FIFO access register can hold only
   one character regardless of the character length, but for eSPI
   controller, the register can hold 4 or 2 characters according to
   the character lengths. Access the Tx/Rx FIFO access register of the
   eSPI controller will shift out/in 4/2 characters one time. For SPI
   subsystem, the command and data are put into different transfers, so
   we need to combine all the transfers to one transfer in order to pass
   the transfer to eSPI controller.

4. The max transaction length limitation
   The max transaction length one time is limitted by the SPCOM[TRANSLEN]
   field which is 0xFFFF. When used mkfs.ext2 command to create ext2
   filesystem on the flash, the read length will exceed the max value of
   the SPCOM[TRANSLEN] field.

Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

drivers/spi/Kconfig

@@ -195,6 +195,15 @@ config SPI_FSL_SPI
 	  MPC83xx platform uses the controller in cpu mode or CPM/QE mode.
 	  MPC8569 uses the controller in QE mode, MPC8610 in cpu mode.
 
+config SPI_FSL_ESPI
+	tristate "Freescale eSPI controller"
+	depends on FSL_SOC
+	select SPI_FSL_LIB
+	help
+	  This enables using the Freescale eSPI controllers in master mode.
+	  From MPC8536, 85xx platform uses the controller, and all P10xx,
+	  P20xx, P30xx,P40xx, P50xx uses this controller.
+
 config SPI_OMAP_UWIRE
 	tristate "OMAP1 MicroWire"
 	depends on ARCH_OMAP1

drivers/spi/Makefile

@@ -33,6 +33,7 @@ obj-$(CONFIG_SPI_MPC512x_PSC)		+= mpc512x_psc_spi.o
 obj-$(CONFIG_SPI_MPC52xx_PSC)		+= mpc52xx_psc_spi.o
 obj-$(CONFIG_SPI_MPC52xx)		+= mpc52xx_spi.o
 obj-$(CONFIG_SPI_FSL_LIB)		+= spi_fsl_lib.o
+obj-$(CONFIG_SPI_FSL_ESPI)		+= spi_fsl_espi.o
 obj-$(CONFIG_SPI_FSL_SPI)		+= spi_fsl_spi.o
 obj-$(CONFIG_SPI_PPC4xx)		+= spi_ppc4xx.o
 obj-$(CONFIG_SPI_S3C24XX_GPIO)		+= spi_s3c24xx_gpio.o