---

yaml
---
r: 322623
b: refs/heads/master
c: 22b4e63
h: refs/heads/master
i:
  322621: 0f1dbbd
  322619: e279562
  322615: 4780cdc
  322607: 692b37a
  322591: 21c4313
  322559: 0be7cf4
v: v3

[refs]

@@ -1,2 +1,2 @@
 ---
-refs/heads/master: 7b281ee026552f10862b617a2a51acf49c829554
+refs/heads/master: 22b4e63ebe062e2e3d4a3a2b468e47ca9575d598

trunk/Documentation/ABI/testing/sysfs-bus-pci

@@ -210,3 +210,15 @@ Users:
 		firmware assigned instance number of the PCI
 		device that can help in understanding the firmware
 		intended order of the PCI device.
+
+What:		/sys/bus/pci/devices/.../d3cold_allowed
+Date:		July 2012
+Contact:	Huang Ying <ying.huang@intel.com>
+Description:
+		d3cold_allowed is bit to control whether the corresponding PCI
+		device can be put into D3Cold state.  If it is cleared, the
+		device will never be put into D3Cold state.  If it is set, the
+		device may be put into D3Cold state if other requirements are
+		satisfied too.  Reading this attribute will show the current
+		value of d3cold_allowed bit.  Writing this attribute will set
+		the value of d3cold_allowed bit.

trunk/Documentation/ABI/testing/sysfs-devices-platform-sh_mobile_lcdc_fb

@@ -0,0 +1,44 @@
+What:		/sys/devices/platform/sh_mobile_lcdc_fb.[0-3]/graphics/fb[0-9]/ovl_alpha
+Date:		May 2012
+Contact:	Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+Description:
+		This file is only available on fb[0-9] devices corresponding
+		to overlay planes.
+
+		Stores the alpha blending value for the overlay. Values range
+		from 0 (transparent) to 255 (opaque). The value is ignored if
+		the mode is not set to Alpha Blending.
+
+What:		/sys/devices/platform/sh_mobile_lcdc_fb.[0-3]/graphics/fb[0-9]/ovl_mode
+Date:		May 2012
+Contact:	Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+Description:
+		This file is only available on fb[0-9] devices corresponding
+		to overlay planes.
+
+		Selects the composition mode for the overlay. Possible values
+		are
+
+		0 - Alpha Blending
+		1 - ROP3
+
+What:		/sys/devices/platform/sh_mobile_lcdc_fb.[0-3]/graphics/fb[0-9]/ovl_position
+Date:		May 2012
+Contact:	Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+Description:
+		This file is only available on fb[0-9] devices corresponding
+		to overlay planes.
+
+		Stores the x,y overlay position on the display in pixels. The
+		position format is `[0-9]+,[0-9]+'.
+
+What:		/sys/devices/platform/sh_mobile_lcdc_fb.[0-3]/graphics/fb[0-9]/ovl_rop3
+Date:		May 2012
+Contact:	Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+Description:
+		This file is only available on fb[0-9] devices corresponding
+		to overlay planes.
+
+		Stores the raster operation (ROP3) for the overlay. Values
+		range from 0 to 255. The value is ignored if the mode is not
+		set to ROP3.

trunk/Documentation/ABI/testing/sysfs-platform-ideapad-laptop

@@ -5,4 +5,15 @@ Contact:	"Ike Panhc <ike.pan@canonical.com>"
 Description:
 		Control the power of camera module. 1 means on, 0 means off.
 
+What:		/sys/devices/platform/ideapad/fan_mode
+Date:		June 2012
+KernelVersion:	3.6
+Contact:	"Maxim Mikityanskiy <maxtram95@gmail.com>"
+Description:
+		Change fan mode
+		There are four available modes:
+			* 0 -> Super Silent Mode
+			* 1 -> Standard Mode
+			* 2 -> Dust Cleaning
+			* 4 -> Efficient Thermal Dissipation Mode
 

trunk/Documentation/DocBook/filesystems.tmpl

@@ -224,8 +224,8 @@ all your transactions.
 </para>
 
 <para>
-Then at umount time , in your put_super() (2.4) or write_super() (2.5)
-you can then call journal_destroy() to clean up your in-core journal object.
+Then at umount time , in your put_super() you can then call journal_destroy()
+to clean up your in-core journal object.
 </para>
 
 <para>

trunk/Documentation/DocBook/media/v4l/vidioc-g-tuner.xml

@@ -125,7 +125,7 @@ the structure refers to a radio tuner the
 <constant>V4L2_TUNER_CAP_NORM</constant> flags can't be used.</para>
 <para>If multiple frequency bands are supported, then
 <structfield>capability</structfield> is the union of all
-<structfield>capability></structfield> fields of each &v4l2-frequency-band;.
+<structfield>capability</structfield> fields of each &v4l2-frequency-band;.
 </para></entry>
 	  </row>
 	  <row>

trunk/Documentation/block/00-INDEX

@@ -3,15 +3,21 @@
 biodoc.txt
 	- Notes on the Generic Block Layer Rewrite in Linux 2.5
 capability.txt
-	- Generic Block Device Capability (/sys/block/<disk>/capability)
+	- Generic Block Device Capability (/sys/block/<device>/capability)
+cfq-iosched.txt
+	- CFQ IO scheduler tunables
+data-integrity.txt
+	- Block data integrity
 deadline-iosched.txt
 	- Deadline IO scheduler tunables
 ioprio.txt
 	- Block io priorities (in CFQ scheduler)
+queue-sysfs.txt
+	- Queue's sysfs entries
 request.txt
 	- The members of struct request (in include/linux/blkdev.h)
 stat.txt
-	- Block layer statistics in /sys/block/<dev>/stat
+	- Block layer statistics in /sys/block/<device>/stat
 switching-sched.txt
 	- Switching I/O schedulers at runtime
 writeback_cache_control.txt

trunk/Documentation/block/cfq-iosched.txt

@@ -1,3 +1,14 @@
+CFQ (Complete Fairness Queueing)
+===============================
+
+The main aim of CFQ scheduler is to provide a fair allocation of the disk
+I/O bandwidth for all the processes which requests an I/O operation.
+
+CFQ maintains the per process queue for the processes which request I/O
+operation(syncronous requests). In case of asynchronous requests, all the
+requests from all the processes are batched together according to their
+process's I/O priority.
+
 CFQ ioscheduler tunables
 ========================
 
@@ -25,6 +36,72 @@ there are multiple spindles behind single LUN (Host based hardware RAID
 controller or for storage arrays), setting slice_idle=0 might end up in better
 throughput and acceptable latencies.
 
+back_seek_max
+-------------
+This specifies, given in Kbytes, the maximum "distance" for backward seeking.
+The distance is the amount of space from the current head location to the
+sectors that are backward in terms of distance.
+
+This parameter allows the scheduler to anticipate requests in the "backward"
+direction and consider them as being the "next" if they are within this
+distance from the current head location.
+
+back_seek_penalty
+-----------------
+This parameter is used to compute the cost of backward seeking. If the
+backward distance of request is just 1/back_seek_penalty from a "front"
+request, then the seeking cost of two requests is considered equivalent.
+
+So scheduler will not bias toward one or the other request (otherwise scheduler
+will bias toward front request). Default value of back_seek_penalty is 2.
+
+fifo_expire_async
+-----------------
+This parameter is used to set the timeout of asynchronous requests. Default
+value of this is 248ms.
+
+fifo_expire_sync
+----------------
+This parameter is used to set the timeout of synchronous requests. Default
+value of this is 124ms. In case to favor synchronous requests over asynchronous
+one, this value should be decreased relative to fifo_expire_async.
+
+slice_async
+-----------
+This parameter is same as of slice_sync but for asynchronous queue. The
+default value is 40ms.
+
+slice_async_rq
+--------------
+This parameter is used to limit the dispatching of asynchronous request to
+device request queue in queue's slice time. The maximum number of request that
+are allowed to be dispatched also depends upon the io priority. Default value
+for this is 2.
+
+slice_sync
+----------
+When a queue is selected for execution, the queues IO requests are only
+executed for a certain amount of time(time_slice) before switching to another
+queue. This parameter is used to calculate the time slice of synchronous
+queue.
+
+time_slice is computed using the below equation:-
+time_slice = slice_sync + (slice_sync/5 * (4 - prio)). To increase the
+time_slice of synchronous queue, increase the value of slice_sync. Default
+value is 100ms.
+
+quantum
+-------
+This specifies the number of request dispatched to the device queue. In a
+queue's time slice, a request will not be dispatched if the number of request
+in the device exceeds this parameter. This parameter is used for synchronous
+request.
+
+In case of storage with several disk, this setting can limit the parallel
+processing of request. Therefore, increasing the value can imporve the
+performace although this can cause the latency of some I/O to increase due
+to more number of requests.
+
 CFQ IOPS Mode for group scheduling
 ===================================
 Basic CFQ design is to provide priority based time slices. Higher priority

trunk/Documentation/block/queue-sysfs.txt

@@ -9,20 +9,71 @@ These files are the ones found in the /sys/block/xxx/queue/ directory.
 Files denoted with a RO postfix are readonly and the RW postfix means
 read-write.
 
+add_random (RW)
+----------------
+This file allows to trun off the disk entropy contribution. Default
+value of this file is '1'(on).
+
+discard_granularity (RO)
+-----------------------
+This shows the size of internal allocation of the device in bytes, if
+reported by the device. A value of '0' means device does not support
+the discard functionality.
+
+discard_max_bytes (RO)
+----------------------
+Devices that support discard functionality may have internal limits on
+the number of bytes that can be trimmed or unmapped in a single operation.
+The discard_max_bytes parameter is set by the device driver to the maximum
+number of bytes that can be discarded in a single operation. Discard
+requests issued to the device must not exceed this limit. A discard_max_bytes
+value of 0 means that the device does not support discard functionality.
+
+discard_zeroes_data (RO)
+------------------------
+When read, this file will show if the discarded block are zeroed by the
+device or not. If its value is '1' the blocks are zeroed otherwise not.
+
 hw_sector_size (RO)
 -------------------
 This is the hardware sector size of the device, in bytes.
 
+iostats (RW)
+-------------
+This file is used to control (on/off) the iostats accounting of the
+disk.
+
+logical_block_size (RO)
+-----------------------
+This is the logcal block size of the device, in bytes.
+
 max_hw_sectors_kb (RO)
 ----------------------
 This is the maximum number of kilobytes supported in a single data transfer.
 
+max_integrity_segments (RO)
+---------------------------
+When read, this file shows the max limit of integrity segments as
+set by block layer which a hardware controller can handle.
+
 max_sectors_kb (RW)
 -------------------
 This is the maximum number of kilobytes that the block layer will allow
 for a filesystem request. Must be smaller than or equal to the maximum
 size allowed by the hardware.
 
+max_segments (RO)
+-----------------
+Maximum number of segments of the device.
+
+max_segment_size (RO)
+---------------------
+Maximum segment size of the device.
+
+minimum_io_size (RO)
+--------------------
+This is the smallest preferred io size reported by the device.
+
 nomerges (RW)
 -------------
 This enables the user to disable the lookup logic involved with IO
@@ -38,11 +89,31 @@ read or write requests. Note that the total allocated number may be twice
 this amount, since it applies only to reads or writes (not the accumulated
 sum).
 
+To avoid priority inversion through request starvation, a request
+queue maintains a separate request pool per each cgroup when
+CONFIG_BLK_CGROUP is enabled, and this parameter applies to each such
+per-block-cgroup request pool.  IOW, if there are N block cgroups,
+each request queue may have upto N request pools, each independently
+regulated by nr_requests.
+
+optimal_io_size (RO)
+--------------------
+This is the optimal io size reported by the device.
+
+physical_block_size (RO)
+------------------------
+This is the physical block size of device, in bytes.
+
 read_ahead_kb (RW)
 ------------------
 Maximum number of kilobytes to read-ahead for filesystems on this block
 device.
 
+rotational (RW)
+---------------
+This file is used to stat if the device is of rotational type or
+non-rotational type.
+
 rq_affinity (RW)
 ----------------
 If this option is '1', the block layer will migrate request completions to the

trunk/Documentation/device-mapper/dm-raid.txt

@@ -27,6 +27,10 @@ The target is named "raid" and it accepts the following parameters:
 		- rotating parity N (right-to-left) with data restart
   raid6_nc	RAID6 N continue
 		- rotating parity N (right-to-left) with data continuation
+  raid10        Various RAID10 inspired algorithms chosen by additional params
+		- RAID10: Striped Mirrors (aka 'Striping on top of mirrors')
+		- RAID1E: Integrated Adjacent Stripe Mirroring
+		-  and other similar RAID10 variants
 
   Reference: Chapter 4 of
   http://www.snia.org/sites/default/files/SNIA_DDF_Technical_Position_v2.0.pdf
@@ -59,6 +63,28 @@ The target is named "raid" and it accepts the following parameters:
 		logical size of the array.  The bitmap records the device
 		synchronisation state for each region.
 
+        [raid10_copies   <# copies>]
+        [raid10_format   near]
+		These two options are used to alter the default layout of
+		a RAID10 configuration.  The number of copies is can be
+		specified, but the default is 2.  There are other variations
+		to how the copies are laid down - the default and only current
+		option is "near".  Near copies are what most people think of
+		with respect to mirroring.  If these options are left
+		unspecified, or 'raid10_copies 2' and/or 'raid10_format near'
+		are given, then the layouts for 2, 3 and 4 devices are:
+		2 drives         3 drives          4 drives
+		--------         ----------        --------------
+		A1  A1           A1  A1  A2        A1  A1  A2  A2
+		A2  A2           A2  A3  A3        A3  A3  A4  A4
+		A3  A3           A4  A4  A5        A5  A5  A6  A6
+		A4  A4           A5  A6  A6        A7  A7  A8  A8
+		..  ..           ..  ..  ..        ..  ..  ..  ..
+		The 2-device layout is equivalent 2-way RAID1.  The 4-device
+		layout is what a traditional RAID10 would look like.  The
+		3-device layout is what might be called a 'RAID1E - Integrated
+		Adjacent Stripe Mirroring'.
+
 <#raid_devs>: The number of devices composing the array.
 	Each device consists of two entries.  The first is the device
 	containing the metadata (if any); the second is the one containing the

trunk/Documentation/devicetree/bindings/arm/mrvl/intc.txt

@@ -38,3 +38,23 @@ Example:
 		reg-names = "mux status", "mux mask";
 		mrvl,intc-nr-irqs = <2>;
 	};
+
+* Marvell Orion Interrupt controller
+
+Required properties
+- compatible :  Should be "marvell,orion-intc".
+- #interrupt-cells: Specifies the number of cells needed to encode an
+  interrupt source. Supported value is <1>.
+- interrupt-controller : Declare this node to be an interrupt controller.
+- reg : Interrupt mask address. A list of 4 byte ranges, one per controller.
+        One entry in the list represents 32 interrupts.
+
+Example:
+
+	intc: interrupt-controller {
+        	compatible = "marvell,orion-intc", "marvell,intc";
+		interrupt-controller;
+		#interrupt-cells = <1>;
+                reg = <0xfed20204 0x04>,
+		      <0xfed20214 0x04>;
+        };

trunk/Documentation/devicetree/bindings/ata/marvell.txt

@@ -0,0 +1,16 @@
+* Marvell Orion SATA
+
+Required Properties:
+- compatibility : "marvell,orion-sata"
+- reg           : Address range of controller
+- interrupts    : Interrupt controller is using
+- nr-ports      : Number of SATA ports in use.
+
+Example:
+
+	sata@80000 {
+		compatible = "marvell,orion-sata";
+		reg = <0x80000 0x5000>;
+		interrupts = <21>;
+		nr-ports = <2>;
+	}