Merge tag 'mfd-lee-3.13-1' of git://git.linaro.org/people/ljones/mfd

mfd-lee-3.13-1

MFD patches due for v3.13.

Documentation/devicetree/bindings/mfd/as3722.txt

@@ -0,0 +1,194 @@
+* ams AS3722 Power management IC.
+
+Required properties:
+-------------------
+- compatible: Must be "ams,as3722".
+- reg: I2C device address.
+- interrupt-controller: AS3722 has internal interrupt controller which takes the
+  interrupt request from internal sub-blocks like RTC, regulators, GPIOs as well
+  as external input.
+- #interrupt-cells: Should be set to 2 for IRQ number and flags.
+  The first cell is the IRQ number. IRQ numbers for different interrupt source
+  of AS3722 are defined at dt-bindings/mfd/as3722.h
+  The second cell is the flags, encoded as the trigger masks from binding document
+	interrupts.txt, using dt-bindings/irq.
+
+Optional submodule and their properties:
+=======================================
+
+Pinmux and GPIO:
+===============
+Device has 8 GPIO pins which can be configured as GPIO as well as the special IO
+functions.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+Following are properties which is needed if GPIO and pinmux functionality
+is required:
+    Required properties:
+    -------------------
+	- gpio-controller: Marks the device node as a GPIO controller.
+	- #gpio-cells: Number of GPIO cells. Refer to binding document
+			gpio/gpio.txt
+
+    Optional properties:
+    --------------------
+	Following properties are require if pin control setting is required
+	at boot.
+	- pinctrl-names: A pinctrl state named "default" be defined, using the
+		bindings in pinctrl/pinctrl-binding.txt.
+	- pinctrl[0...n]: Properties to contain the phandle that refer to
+		different nodes of pin control settings. These nodes represents
+		the pin control setting of state 0 to state n. Each of these
+		nodes contains different subnodes to represents some desired
+		configuration for a list of pins. This configuration can
+		include the mux function to select on those pin(s), and
+		various pin configuration parameters, such as pull-up,
+		open drain.
+
+		Each subnode have following properties:
+		Required properties:
+		    - pins: List of pins. Valid values of pins properties are:
+				gpio0, gpio1, gpio2, gpio3, gpio4, gpio5,
+				gpio6, gpio7
+
+		Optional properties:
+			function, bias-disable, bias-pull-up, bias-pull-down,
+			bias-high-impedance, drive-open-drain.
+
+			Valid values for function properties are:
+				gpio, interrupt-out, gpio-in-interrupt,
+				vsup-vbat-low-undebounce-out,
+				vsup-vbat-low-debounce-out,
+				voltage-in-standby, oc-pg-sd0, oc-pg-sd6,
+				powergood-out, pwm-in, pwm-out, clk32k-out,
+				watchdog-in, soft-reset-in
+
+Regulators:
+===========
+Device has multiple DCDC and LDOs. The node "regulators" is require if regulator
+functionality is needed.
+
+Following are properties of regulator subnode.
+
+    Optional properties:
+    -------------------
+	The input supply of regulators are the optional properties on the
+	regulator node. The input supply of these regulators are provided
+	through following properties:
+		vsup-sd2-supply: Input supply for SD2.
+		vsup-sd3-supply: Input supply for SD3.
+		vsup-sd4-supply: Input supply for SD4.
+		vsup-sd5-supply: Input supply for SD5.
+		vin-ldo0-supply: Input supply for LDO0.
+		vin-ldo1-6-supply: Input supply for LDO1 and LDO6.
+		vin-ldo2-5-7-supply: Input supply for LDO2, LDO5 and LDO7.
+		vin-ldo3-4-supply: Input supply for LDO3 and LDO4.
+		vin-ldo9-10-supply: Input supply for LDO9 and LDO10.
+		vin-ldo11-supply: Input supply for LDO11.
+
+    Optional sub nodes for regulators:
+    ---------------------------------
+	The subnodes name is the name of regulator and it must be one of:
+	sd[0-6], ldo[0-7], ldo[9-11]
+
+	Each sub-node should contain the constraints and initialization
+	information for that regulator. See regulator.txt for a description
+	of standard properties for these sub-nodes.
+	Additional optional custom properties  are listed below.
+		ams,ext-control: External control of the rail. The option of
+			this properties will tell which external input is
+			controlling this rail. Valid values are 0, 1, 2 ad 3.
+			0: There is no external control of this rail.
+			1: Rail is controlled by ENABLE1 input pin.
+			2: Rail is controlled by ENABLE2 input pin.
+			3: Rail is controlled by ENABLE3 input pin.
+			Missing this property on DT will be assume as no
+			external control. The external control pin macros
+			are defined @dt-bindings/mfd/as3722.h
+
+		ams,enable-tracking: Enable tracking with SD1, only supported
+			by LDO3.
+
+Example:
+--------
+#include <dt-bindings/mfd/as3722.h>
+...
+ams3722 {
+	compatible = "ams,as3722";
+	reg = <0x48>;
+
+	interrupt-parent = <&intc>;
+	interrupt-controller;
+	#interrupt-cells = <2>;
+
+	gpio-controller;
+	#gpio-cells = <2>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&as3722_default>;
+
+	as3722_default: pinmux {
+			gpio0 {
+				pins = "gpio0";
+				function = "gpio";
+				bias-pull-down;
+			};
+
+			gpio1_2_4_7 {
+				pins = "gpio1", "gpio2", "gpio4", "gpio7";
+				function = "gpio";
+				bias-pull-up;
+			};
+
+			gpio5 {
+				pins = "gpio5";
+				function = "clk32k_out";
+			};
+	}
+
+	regulators {
+			vsup-sd2-supply = <...>;
+			...
+
+			sd0 {
+				regulator-name = "vdd_cpu";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1400000>;
+				regulator-always-on;
+				ams,ext-control = <2>;
+			};
+
+			sd1 {
+				regulator-name = "vdd_core";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1400000>;
+				regulator-always-on;
+				ams,ext-control = <1>;
+			};
+
+			sd2 {
+				regulator-name = "vddio_ddr";
+				regulator-min-microvolt = <1350000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+			};
+
+			sd4 {
+				regulator-name = "avdd-hdmi-pex";
+				regulator-min-microvolt = <1050000>;
+				regulator-max-microvolt = <1050000>;
+				regulator-always-on;
+			};
+
+			sd5 {
+				regulator-name = "vdd-1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+			....
+	};
+};

drivers/mfd/88pm860x-core.c

@@ -1247,7 +1247,7 @@ static struct i2c_driver pm860x_driver = {
 		.name	= "88PM860x",
 		.owner	= THIS_MODULE,
 		.pm     = &pm860x_pm_ops,
-		.of_match_table	= of_match_ptr(pm860x_dt_ids),
+		.of_match_table	= pm860x_dt_ids,
 	},
 	.probe		= pm860x_probe,
 	.remove		= pm860x_remove,

drivers/mfd/Kconfig

@@ -27,6 +27,18 @@ config MFD_AS3711
 	help
 	  Support for the AS3711 PMIC from AMS
 
+config MFD_AS3722
+	bool "ams AS3722 Power Management IC"
+	select MFD_CORE
+	select REGMAP_I2C
+	select REGMAP_IRQ
+	depends on I2C && OF
+	help
+	  The ams AS3722 is a compact system PMU suitable for mobile phones,
+	  tablets etc. It has 4 DC/DC step-down regulators, 3 DC/DC step-down
+	  controllers, 11 LDOs, RTC, automatic battery, temperature and
+	  over current monitoring, GPIOs, ADC and a watchdog.
+
 config PMIC_ADP5520
 	bool "Analog Devices ADP5520/01 MFD PMIC Core Support"
 	depends on I2C=y
@@ -1151,6 +1163,16 @@ config MFD_WM8994
 	  core support for the WM8994, in order to use the actual
 	  functionaltiy of the device other drivers must be enabled.
 
+config MFD_STW481X
+	bool "Support for ST Microelectronics STw481x"
+	depends on I2C && ARCH_NOMADIK
+	select REGMAP_I2C
+	select MFD_CORE
+	help
+	  Select this option to enable the STw481x chip driver used
+	  in various ST Microelectronics and ST-Ericsson embedded
+	  Nomadik series.
+
 endmenu
 endif
 

drivers/mfd/Makefile

@@ -162,3 +162,5 @@ obj-$(CONFIG_MFD_LM3533)	+= lm3533-core.o lm3533-ctrlbank.o
 obj-$(CONFIG_VEXPRESS_CONFIG)	+= vexpress-config.o vexpress-sysreg.o
 obj-$(CONFIG_MFD_RETU)		+= retu-mfd.o
 obj-$(CONFIG_MFD_AS3711)	+= as3711.o
+obj-$(CONFIG_MFD_AS3722)	+= as3722.o
+obj-$(CONFIG_MFD_STW481X)	+= stw481x.o

drivers/mfd/aat2870-core.c

@@ -293,7 +293,7 @@ static ssize_t aat2870_reg_write_file(struct file *file,
 	unsigned long addr, val;
 	int ret;
 
-	buf_size = min(count, (sizeof(buf)-1));
+	buf_size = min(count, (size_t)(sizeof(buf)-1));
 	if (copy_from_user(buf, user_buf, buf_size)) {
 		dev_err(aat2870->dev, "Failed to copy from user\n");
 		return -EFAULT;

drivers/mfd/arizona-core.c

@@ -540,7 +540,7 @@ static int arizona_of_get_core_pdata(struct arizona *arizona)
 		for (i = 0; i < ARRAY_SIZE(arizona->pdata.gpio_defaults); i++) {
 			if (arizona->pdata.gpio_defaults[i] > 0xffff)
 				arizona->pdata.gpio_defaults[i] = 0;
-			if (arizona->pdata.gpio_defaults[i] == 0)
+			else if (arizona->pdata.gpio_defaults[i] == 0)
 				arizona->pdata.gpio_defaults[i] = 0x10000;
 		}
 	} else {
@@ -607,11 +607,11 @@ int arizona_dev_init(struct arizona *arizona)
 	dev_set_drvdata(arizona->dev, arizona);
 	mutex_init(&arizona->clk_lock);
 
-	arizona_of_get_core_pdata(arizona);
-
 	if (dev_get_platdata(arizona->dev))
 		memcpy(&arizona->pdata, dev_get_platdata(arizona->dev),
 		       sizeof(arizona->pdata));
+	else
+		arizona_of_get_core_pdata(arizona);
 
 	regcache_cache_only(arizona->regmap, true);
 

drivers/mfd/arizona-i2c.c

@@ -17,6 +17,7 @@
 #include <linux/regmap.h>
 #include <linux/regulator/consumer.h>
 #include <linux/slab.h>
+#include <linux/of.h>
 
 #include <linux/mfd/arizona/core.h>
 

drivers/mfd/arizona-spi.c

@@ -17,6 +17,7 @@
 #include <linux/regulator/consumer.h>
 #include <linux/slab.h>
 #include <linux/spi/spi.h>
+#include <linux/of.h>
 
 #include <linux/mfd/arizona/core.h>
 

drivers/mfd/as3711.c

@@ -17,6 +17,7 @@
 #include <linux/mfd/as3711.h>
 #include <linux/mfd/core.h>
 #include <linux/module.h>
+#include <linux/of.h>
 #include <linux/regmap.h>
 #include <linux/slab.h>