---

yaml
---
r: 154140
b: refs/heads/master
c: 936940a
h: refs/heads/master
v: v3

[refs]

@@ -1,2 +1,2 @@
 ---
-refs/heads/master: 1cbd20d820c36f52543e3e4cd0067ebf52aa388f
+refs/heads/master: 936940a9c7e3d99b25859bf1ff140d8c2480183a

trunk/arch/x86/kernel/apic/io_apic.c

@@ -1414,6 +1414,9 @@ int setup_ioapic_entry(int apic_id, int irq,
 		irte.vector = vector;
 		irte.dest_id = IRTE_DEST(destination);
 
+		/* Set source-id of interrupt request */
+		set_ioapic_sid(&irte, apic_id);
+
 		modify_irte(irq, &irte);
 
 		ir_entry->index2 = (index >> 15) & 0x1;
@@ -3290,6 +3293,9 @@ static int msi_compose_msg(struct pci_dev *pdev, unsigned int irq, struct msi_ms
 		irte.vector = cfg->vector;
 		irte.dest_id = IRTE_DEST(dest);
 
+		/* Set source-id of interrupt request */
+		set_msi_sid(&irte, pdev);
+
 		modify_irte(irq, &irte);
 
 		msg->address_hi = MSI_ADDR_BASE_HI;

trunk/drivers/char/mxser.c

@@ -1048,8 +1048,6 @@ static int mxser_open(struct tty_struct *tty, struct file *filp)
 	if (retval)
 		return retval;
 
-	/* unmark here for very high baud rate (ex. 921600 bps) used */
-	tty->low_latency = 1;
 	return 0;
 }
 

trunk/drivers/char/nozomi.c

@@ -1591,8 +1591,6 @@ static int ntty_open(struct tty_struct *tty, struct file *file)
 
 	/* Enable interrupt downlink for channel */
 	if (port->port.count == 1) {
-		/* FIXME: is this needed now ? */
-		tty->low_latency = 1;
 		tty->driver_data = port;
 		tty_port_tty_set(&port->port, tty);
 		DBG1("open: %d", port->token_dl);

trunk/drivers/char/synclink_gt.c

@@ -467,7 +467,6 @@ static unsigned int free_tbuf_count(struct slgt_info *info);
 static unsigned int tbuf_bytes(struct slgt_info *info);
 static void reset_tbufs(struct slgt_info *info);
 static void tdma_reset(struct slgt_info *info);
-static void tdma_start(struct slgt_info *info);
 static void tx_load(struct slgt_info *info, const char *buf, unsigned int count);
 
 static void get_signals(struct slgt_info *info);
@@ -795,6 +794,18 @@ static void set_termios(struct tty_struct *tty, struct ktermios *old_termios)
 	}
 }
 
+static void update_tx_timer(struct slgt_info *info)
+{
+	/*
+	 * use worst case speed of 1200bps to calculate transmit timeout
+	 * based on data in buffers (tbuf_bytes) and FIFO (128 bytes)
+	 */
+	if (info->params.mode == MGSL_MODE_HDLC) {
+		int timeout  = (tbuf_bytes(info) * 7) + 1000;
+		mod_timer(&info->tx_timer, jiffies + msecs_to_jiffies(timeout));
+	}
+}
+
 static int write(struct tty_struct *tty,
 		 const unsigned char *buf, int count)
 {
@@ -838,8 +849,18 @@ static int write(struct tty_struct *tty,
 		spin_lock_irqsave(&info->lock,flags);
 		if (!info->tx_active)
 		 	tx_start(info);
-		else
-			tdma_start(info);
+		else if (!(rd_reg32(info, TDCSR) & BIT0)) {
+			/* transmit still active but transmit DMA stopped */
+			unsigned int i = info->tbuf_current;
+			if (!i)
+				i = info->tbuf_count;
+			i--;
+			/* if DMA buf unsent must try later after tx idle */
+			if (desc_count(info->tbufs[i]))
+				ret = 0;
+		}
+		if (ret > 0)
+			update_tx_timer(info);
 		spin_unlock_irqrestore(&info->lock,flags);
  	}
 
@@ -1502,10 +1523,9 @@ static int hdlcdev_xmit(struct sk_buff *skb, struct net_device *dev)
 	/* save start time for transmit timeout detection */
 	dev->trans_start = jiffies;
 
-	/* start hardware transmitter if necessary */
 	spin_lock_irqsave(&info->lock,flags);
-	if (!info->tx_active)
-	 	tx_start(info);
+	tx_start(info);
+	update_tx_timer(info);
 	spin_unlock_irqrestore(&info->lock,flags);
 
 	return 0;
@@ -3946,50 +3966,19 @@ static void tx_start(struct slgt_info *info)
 			slgt_irq_on(info, IRQ_TXUNDER + IRQ_TXIDLE);
 			/* clear tx idle and underrun status bits */
 			wr_reg16(info, SSR, (unsigned short)(IRQ_TXIDLE + IRQ_TXUNDER));
-			if (info->params.mode == MGSL_MODE_HDLC)
-				mod_timer(&info->tx_timer, jiffies +
-						msecs_to_jiffies(5000));
 		} else {
 			slgt_irq_off(info, IRQ_TXDATA);
 			slgt_irq_on(info, IRQ_TXIDLE);
 			/* clear tx idle status bit */
 			wr_reg16(info, SSR, IRQ_TXIDLE);
 		}
-		tdma_start(info);
+		/* set 1st descriptor address and start DMA */
+		wr_reg32(info, TDDAR, info->tbufs[info->tbuf_start].pdesc);
+		wr_reg32(info, TDCSR, BIT2 + BIT0);
 		info->tx_active = true;
 	}
 }
 
-/*
- * start transmit DMA if inactive and there are unsent buffers
- */
-static void tdma_start(struct slgt_info *info)
-{
-	unsigned int i;
-
-	if (rd_reg32(info, TDCSR) & BIT0)
-		return;
-
-	/* transmit DMA inactive, check for unsent buffers */
-	i = info->tbuf_start;
-	while (!desc_count(info->tbufs[i])) {
-		if (++i == info->tbuf_count)
-			i = 0;
-		if (i == info->tbuf_current)
-			return;
-	}
-	info->tbuf_start = i;
-
-	/* there are unsent buffers, start transmit DMA */
-
-	/* reset needed if previous error condition */
-	tdma_reset(info);
-
-	/* set 1st descriptor address */
-	wr_reg32(info, TDDAR, info->tbufs[info->tbuf_start].pdesc);
-	wr_reg32(info, TDCSR, BIT2 + BIT0); /* IRQ + DMA enable */
-}
-
 static void tx_stop(struct slgt_info *info)
 {
 	unsigned short val;
@@ -5004,8 +4993,7 @@ static void tx_timeout(unsigned long context)
 		info->icount.txtimeout++;
 	}
 	spin_lock_irqsave(&info->lock,flags);
-	info->tx_active = false;
-	info->tx_count = 0;
+	tx_stop(info);
 	spin_unlock_irqrestore(&info->lock,flags);
 
 #if SYNCLINK_GENERIC_HDLC

trunk/drivers/char/tty_port.c

@@ -193,7 +193,7 @@ int tty_port_block_til_ready(struct tty_port *port,
 {
 	int do_clocal = 0, retval;
 	unsigned long flags;
-	DECLARE_WAITQUEUE(wait, current);
+	DEFINE_WAIT(wait);
 	int cd;
 
 	/* block if port is in the process of being closed */

trunk/drivers/i2c/busses/Kconfig

@@ -326,6 +326,15 @@ config I2C_DAVINCI
 	  devices such as DaVinci NIC.
 	  For details please see http://www.ti.com/davinci
 
+config I2C_DESIGNWARE
+	tristate "Synopsys DesignWare"
+	help
+	  If you say yes to this option, support will be included for the
+	  Synopsys DesignWare I2C adapter. Only master mode is supported.
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called i2c-designware.
+
 config I2C_GPIO
 	tristate "GPIO-based bitbanging I2C"
 	depends on GENERIC_GPIO

trunk/drivers/i2c/busses/Makefile

@@ -30,6 +30,7 @@ obj-$(CONFIG_I2C_AU1550)	+= i2c-au1550.o
 obj-$(CONFIG_I2C_BLACKFIN_TWI)	+= i2c-bfin-twi.o
 obj-$(CONFIG_I2C_CPM)		+= i2c-cpm.o
 obj-$(CONFIG_I2C_DAVINCI)	+= i2c-davinci.o
+obj-$(CONFIG_I2C_DESIGNWARE)	+= i2c-designware.o
 obj-$(CONFIG_I2C_GPIO)		+= i2c-gpio.o
 obj-$(CONFIG_I2C_HIGHLANDER)	+= i2c-highlander.o
 obj-$(CONFIG_I2C_IBM_IIC)	+= i2c-ibm_iic.o