Merge branch 'at91/dt' into next/drivers

Merging at91/dt as a prereq for the at91/drivers code. * at91/dt: (43 commits) ARM: at91/at91rm9200ek.dts: rearrange nodes in address ascending order ARM: at91: dt: at91rm9200ek: add emac and nor flash support ARM: at91: add uart aliases to sama5d3 dtsi ARM: at91: add i2c2 pinctrl speficifation to sama5d3 DT ARM: at91: Animeo IP: fix mtd partition table ARM: at91: at91sam9g45: add i2c pinctrl ARM: at91: at91sam9g45: set default mmc pinctrl-names ARM: at91: sama5d3: enable qt1070 as a wakeup source ARM: at91: add support for Cosino board series by HCE Engineering ARM: at91/dt/sama5d3: add DMA information to SHA/AES/TDES nodes ARM: at91/dt/trivial: before sama5d3, Atmel MPU were using at91 prefix ARM: at91/dt/trivial: use macro for AES irq type ARM: at91: sam9263ek: add dt lcd support ARM: at91: at9sam9m10g45ek: add dt lcd support ARM: at91: sam9263: add fb dt support ARM: at91: sam9g45: add fb dt support ARM: at91/dt: binding: add missing compatibility string in SDRAM/DDR documentation ARM: at91/dt: binding: add precision to AIC documentation ARM: at91/dt: add atmel,pullup-gpio to at91rm9200ek usb1 definition ARM: at91/dt: add ethernet phy to at91rm9200ek board ...
git-mirror · Dec 22, 2013 · 958c025 · 958c025
2 parents ddf2039 + ca59484
commit 958c025
Show file tree

Hide file tree

Showing 59 changed files with 4,694 additions and 416 deletions.
diff --git a/Documentation/devicetree/bindings/arm/atmel-aic.txt b/Documentation/devicetree/bindings/arm/atmel-aic.txt
@@ -2,6 +2,7 @@
 
 Required properties:
 - compatible: Should be "atmel,<chip>-aic"
+  <chip> can be "at91rm9200" or "sama5d3"
 - interrupt-controller: Identifies the node as an interrupt controller.
 - interrupt-parent: For single AIC system, it is an empty property.
 - #interrupt-cells: The number of cells to define the interrupts. It should be 3.

diff --git a/Documentation/devicetree/bindings/arm/atmel-at91.txt b/Documentation/devicetree/bindings/arm/atmel-at91.txt
@@ -50,7 +50,8 @@ Example:
 	};
 
 RAMC SDRAM/DDR Controller required properties:
-- compatible: Should be "atmel,at91sam9260-sdramc",
+- compatible: Should be "atmel,at91rm9200-sdramc",
+			"atmel,at91sam9260-sdramc",
 			"atmel,at91sam9g45-ddramc",
 - reg: Should contain registers location and length
   For at91sam9263 and at91sam9g45 you must specify 2 entries.

diff --git a/Documentation/devicetree/bindings/clock/at91-clock.txt b/Documentation/devicetree/bindings/clock/at91-clock.txt
@@ -0,0 +1,339 @@
+Device Tree Clock bindings for arch-at91
+
+This binding uses the common clock binding[1].
+
+[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
+
+Required properties:
+- compatible : shall be one of the following:
+	"atmel,at91rm9200-pmc" or
+	"atmel,at91sam9g45-pmc" or
+	"atmel,at91sam9n12-pmc" or
+	"atmel,at91sam9x5-pmc" or
+	"atmel,sama5d3-pmc":
+		at91 PMC (Power Management Controller)
+		All at91 specific clocks (clocks defined below) must be child
+		node of the PMC node.
+
+	"atmel,at91rm9200-clk-main":
+		at91 main oscillator
+
+	"atmel,at91rm9200-clk-master" or
+	"atmel,at91sam9x5-clk-master":
+		at91 master clock
+
+	"atmel,at91sam9x5-clk-peripheral" or
+	"atmel,at91rm9200-clk-peripheral":
+		at91 peripheral clocks
+
+	"atmel,at91rm9200-clk-pll" or
+	"atmel,at91sam9g45-clk-pll" or
+	"atmel,at91sam9g20-clk-pllb" or
+	"atmel,sama5d3-clk-pll":
+		at91 pll clocks
+
+	"atmel,at91sam9x5-clk-plldiv":
+		at91 plla divisor
+
+	"atmel,at91rm9200-clk-programmable" or
+	"atmel,at91sam9g45-clk-programmable" or
+	"atmel,at91sam9x5-clk-programmable":
+		at91 programmable clocks
+
+	"atmel,at91sam9x5-clk-smd":
+		at91 SMD (Soft Modem) clock
+
+	"atmel,at91rm9200-clk-system":
+		at91 system clocks
+
+	"atmel,at91rm9200-clk-usb" or
+	"atmel,at91sam9x5-clk-usb" or
+	"atmel,at91sam9n12-clk-usb":
+		at91 usb clock
+
+	"atmel,at91sam9x5-clk-utmi":
+		at91 utmi clock
+
+Required properties for PMC node:
+- reg : defines the IO memory reserved for the PMC.
+- #size-cells : shall be 0 (reg is used to encode clk id).
+- #address-cells : shall be 1 (reg is used to encode clk id).
+- interrupts : shall be set to PMC interrupt line.
+- interrupt-controller : tell that the PMC is an interrupt controller.
+- #interrupt-cells : must be set to 1. The first cell encodes the interrupt id,
+	and reflect the bit position in the PMC_ER/DR/SR registers.
+	You can use the dt macros defined in dt-bindings/clk/at91.h.
+	0 (AT91_PMC_MOSCS) -> main oscillator ready
+	1 (AT91_PMC_LOCKA) -> PLL A ready
+	2 (AT91_PMC_LOCKB) -> PLL B ready
+	3 (AT91_PMC_MCKRDY) -> master clock ready
+	6 (AT91_PMC_LOCKU) -> UTMI PLL clock ready
+	8 .. 15 (AT91_PMC_PCKRDY(id)) -> programmable clock ready
+	16 (AT91_PMC_MOSCSELS) -> main oscillator selected
+	17 (AT91_PMC_MOSCRCS) -> RC main oscillator stabilized
+	18 (AT91_PMC_CFDEV) -> clock failure detected
+
+For example:
+	pmc: pmc@fffffc00 {
+		compatible = "atmel,sama5d3-pmc";
+		interrupts = <1 4 7>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		#size-cells = <0>;
+		#address-cells = <1>;
+
+		/* put at91 clocks here */
+	};
+
+Required properties for main clock:
+- interrupt-parent : must reference the PMC node.
+- interrupts : shall be set to "<0>".
+- #clock-cells : from common clock binding; shall be set to 0.
+- clocks (optional if clock-frequency is provided) : shall be the slow clock
+	phandle. This clock is used to calculate the main clock rate if
+	"clock-frequency" is not provided.
+- clock-frequency : the main oscillator frequency.Prefer the use of
+	"clock-frequency" over automatic clock rate calculation.
+
+For example:
+	main: mainck {
+		compatible = "atmel,at91rm9200-clk-main";
+		interrupt-parent = <&pmc>;
+		interrupts = <0>;
+		#clock-cells = <0>;
+		clocks = <&ck32k>;
+		clock-frequency = <18432000>;
+	};
+
+Required properties for master clock:
+- interrupt-parent : must reference the PMC node.
+- interrupts : shall be set to "<3>".
+- #clock-cells : from common clock binding; shall be set to 0.
+- clocks : shall be the master clock sources (see atmel datasheet) phandles.
+	e.g. "<&ck32k>, <&main>, <&plla>, <&pllb>".
+- atmel,clk-output-range : minimum and maximum clock frequency (two u32
+			   fields).
+	   e.g. output = <0 133000000>; <=> 0 to 133MHz.
+- atmel,clk-divisors : master clock divisors table (four u32 fields).
+		0 <=> reserved value.
+		e.g. divisors = <1 2 4 6>;
+- atmel,master-clk-have-div3-pres : some SoC use the reserved value 7 in the
+				    PRES field as CLOCK_DIV3 (e.g sam9x5).
+
+For example:
+	mck: mck {
+		compatible = "atmel,at91rm9200-clk-master";
+		interrupt-parent = <&pmc>;
+		interrupts = <3>;
+		#clock-cells = <0>;
+		atmel,clk-output-range = <0 133000000>;
+		atmel,clk-divisors = <1 2 4 0>;
+	};
+
+Required properties for peripheral clocks:
+- #size-cells : shall be 0 (reg is used to encode clk id).
+- #address-cells : shall be 1 (reg is used to encode clk id).
+- clocks : shall be the master clock phandle.
+	e.g. clocks = <&mck>;
+- name: device tree node describing a specific system clock.
+	* #clock-cells : from common clock binding; shall be set to 0.
+	* reg: peripheral id. See Atmel's datasheets to get a full
+	  list of peripheral ids.
+	* atmel,clk-output-range : minimum and maximum clock frequency
+	  (two u32 fields). Only valid on at91sam9x5-clk-peripheral
+	  compatible IPs.
+
+For example:
+	periph: periphck {
+		compatible = "atmel,at91sam9x5-clk-peripheral";
+		#size-cells = <0>;
+		#address-cells = <1>;
+		clocks = <&mck>;
+
+		ssc0_clk {
+			#clock-cells = <0>;
+			reg = <2>;
+			atmel,clk-output-range = <0 133000000>;
+		};
+
+		usart0_clk {
+			#clock-cells = <0>;
+			reg = <3>;
+			atmel,clk-output-range = <0 66000000>;
+		};
+	};
+
+
+Required properties for pll clocks:
+- interrupt-parent : must reference the PMC node.
+- interrupts : shall be set to "<1>".
+- #clock-cells : from common clock binding; shall be set to 0.
+- clocks : shall be the main clock phandle.
+- reg : pll id.
+	0 -> PLL A
+	1 -> PLL B
+- atmel,clk-input-range : minimum and maximum source clock frequency (two u32
+			  fields).
+	  e.g. input = <1 32000000>; <=> 1 to 32MHz.
+- #atmel,pll-clk-output-range-cells : number of cells reserved for pll output
+				      range description. Sould be set to 2, 3
+				      or 4.
+	* 1st and 2nd cells represent the frequency range (min-max).
+	* 3rd cell is optional and represents the OUT field value for the given
+	  range.
+	* 4th cell is optional and represents the ICPLL field (PLLICPR
+	  register)
+- atmel,pll-clk-output-ranges : pll output frequency ranges + optional parameter
+				depending on #atmel,pll-output-range-cells
+				property value.
+
+For example:
+	plla: pllack {
+		compatible = "atmel,at91sam9g45-clk-pll";
+		interrupt-parent = <&pmc>;
+		interrupts = <1>;
+		#clock-cells = <0>;
+		clocks = <&main>;
+		reg = <0>;
+		atmel,clk-input-range = <2000000 32000000>;
+		#atmel,pll-clk-output-range-cells = <4>;
+		atmel,pll-clk-output-ranges = <74500000 800000000 0 0
+					       69500000 750000000 1 0
+					       64500000 700000000 2 0
+					       59500000 650000000 3 0
+					       54500000 600000000 0 1
+					       49500000 550000000 1 1
+					       44500000 500000000 2 1
+					       40000000 450000000 3 1>;
+	};
+
+Required properties for plldiv clocks (plldiv = pll / 2):
+- #clock-cells : from common clock binding; shall be set to 0.
+- clocks : shall be the plla clock phandle.
+
+The pll divisor is equal to 2 and cannot be changed.
+
+For example:
+	plladiv: plladivck {
+		compatible = "atmel,at91sam9x5-clk-plldiv";
+		#clock-cells = <0>;
+		clocks = <&plla>;
+	};
+
+Required properties for programmable clocks:
+- interrupt-parent : must reference the PMC node.
+- #size-cells : shall be 0 (reg is used to encode clk id).
+- #address-cells : shall be 1 (reg is used to encode clk id).
+- clocks : shall be the programmable clock source phandles.
+	e.g. clocks = <&clk32k>, <&main>, <&plla>, <&pllb>;
+- name: device tree node describing a specific prog clock.
+	* #clock-cells : from common clock binding; shall be set to 0.
+	* reg : programmable clock id (register offset from  PCKx
+			 register).
+	* interrupts : shall be set to "<(8 + id)>".
+
+For example:
+	prog: progck {
+		compatible = "atmel,at91sam9g45-clk-programmable";
+		#size-cells = <0>;
+		#address-cells = <1>;
+		interrupt-parent = <&pmc>;
+		clocks = <&clk32k>, <&main>, <&plladiv>, <&utmi>, <&mck>;
+
+		prog0 {
+			#clock-cells = <0>;
+			reg = <0>;
+			interrupts = <8>;
+		};
+
+		prog1 {
+			#clock-cells = <0>;
+			reg = <1>;
+			interrupts = <9>;
+		};
+	};
+
+
+Required properties for smd clock:
+- #clock-cells : from common clock binding; shall be set to 0.
+- clocks : shall be the smd clock source phandles.
+	e.g. clocks = <&plladiv>, <&utmi>;
+
+For example:
+	smd: smdck {
+		compatible = "atmel,at91sam9x5-clk-smd";
+		#clock-cells = <0>;
+		clocks = <&plladiv>, <&utmi>;
+	};
+
+Required properties for system clocks:
+- #size-cells : shall be 0 (reg is used to encode clk id).
+- #address-cells : shall be 1 (reg is used to encode clk id).
+- name: device tree node describing a specific system clock.
+	* #clock-cells : from common clock binding; shall be set to 0.
+	* reg: system clock id (bit position in SCER/SCDR/SCSR registers).
+	      See Atmel's datasheet to get a full list of system clock ids.
+
+For example:
+	system: systemck {
+		compatible = "atmel,at91rm9200-clk-system";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ddrck {
+			#clock-cells = <0>;
+			reg = <2>;
+			clocks = <&mck>;
+		};
+
+		uhpck {
+			#clock-cells = <0>;
+			reg = <6>;
+			clocks = <&usb>;
+		};
+
+		udpck {
+			#clock-cells = <0>;
+			reg = <7>;
+			clocks = <&usb>;
+		};
+	};
+
+
+Required properties for usb clock:
+- #clock-cells : from common clock binding; shall be set to 0.
+- clocks : shall be the smd clock source phandles.
+	e.g. clocks = <&pllb>;
+- atmel,clk-divisors (only available for "atmel,at91rm9200-clk-usb"):
+	usb clock divisor table.
+	e.g. divisors = <1 2 4 0>;
+
+For example:
+	usb: usbck {
+		compatible = "atmel,at91sam9x5-clk-usb";
+		#clock-cells = <0>;
+		clocks = <&plladiv>, <&utmi>;
+	};
+
+	usb: usbck {
+		compatible = "atmel,at91rm9200-clk-usb";
+		#clock-cells = <0>;
+		clocks = <&pllb>;
+		atmel,clk-divisors = <1 2 4 0>;
+	};
+
+
+Required properties for utmi clock:
+- interrupt-parent : must reference the PMC node.
+- interrupts : shall be set to "<AT91_PMC_LOCKU IRQ_TYPE_LEVEL_HIGH>".
+- #clock-cells : from common clock binding; shall be set to 0.
+- clocks : shall be the main clock source phandle.
+
+For example:
+	utmi: utmick {
+		compatible = "atmel,at91sam9x5-clk-utmi";
+		interrupt-parent = <&pmc>;
+		interrupts = <AT91_PMC_LOCKU IRQ_TYPE_LEVEL_HIGH>;
+		#clock-cells = <0>;
+		clocks = <&main>;
+	};
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
@@ -30,6 +30,7 @@ dtb-$(CONFIG_ARCH_AT91) += pm9g45.dtb
 dtb-$(CONFIG_ARCH_AT91) += at91sam9n12ek.dtb
 # sam9x5
 dtb-$(CONFIG_ARCH_AT91) += at91-ariag25.dtb
+dtb-$(CONFIG_ARCH_AT91) += at91-cosino_mega2560.dtb
 dtb-$(CONFIG_ARCH_AT91) += at91sam9g15ek.dtb
 dtb-$(CONFIG_ARCH_AT91) += at91sam9g25ek.dtb
 dtb-$(CONFIG_ARCH_AT91) += at91sam9g35ek.dtb