Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1958 commits)
  net: pack skb_shared_info more efficiently
  net_sched: red: split red_parms into parms and vars
  net_sched: sfq: extend limits
  cnic: Improve error recovery on bnx2x devices
  cnic: Re-init dev->stats_addr after chip reset
  net_sched: Bug in netem reordering
  bna: fix sparse warnings/errors
  bna: make ethtool_ops and strings const
  xgmac: cleanups
  net: make ethtool_ops const
  vmxnet3" make ethtool ops const
  xen-netback: make ops structs const
  virtio_net: Pass gfp flags when allocating rx buffers.
  ixgbe: FCoE: Add support for ndo_get_fcoe_hbainfo() call
  netdev: FCoE: Add new ndo_get_fcoe_hbainfo() call
  igb: reset PHY after recovering from PHY power down
  igb: add basic runtime PM support
  igb: Add support for byte queue limits.
  e1000: cleanup CE4100 MDIO registers access
  e1000: unmap ce4100_gbe_mdio_base_virt in e1000_remove
  ...

Documentation/cgroups/memory.txt

@@ -44,8 +44,8 @@ Features:
  - oom-killer disable knob and oom-notifier
  - Root cgroup has no limit controls.
 
- Kernel memory and Hugepages are not under control yet. We just manage
- pages on LRU. To add more controls, we have to take care of performance.
+ Kernel memory support is work in progress, and the current version provides
+ basically functionality. (See Section 2.7)
 
 Brief summary of control files.
 
@@ -72,6 +72,9 @@ Brief summary of control files.
  memory.oom_control		 # set/show oom controls.
  memory.numa_stat		 # show the number of memory usage per numa node
 
+ memory.kmem.tcp.limit_in_bytes  # set/show hard limit for tcp buf memory
+ memory.kmem.tcp.usage_in_bytes  # show current tcp buf memory allocation
+
 1. History
 
 The memory controller has a long history. A request for comments for the memory
@@ -255,6 +258,27 @@ When oom event notifier is registered, event will be delivered.
   per-zone-per-cgroup LRU (cgroup's private LRU) is just guarded by
   zone->lru_lock, it has no lock of its own.
 
+2.7 Kernel Memory Extension (CONFIG_CGROUP_MEM_RES_CTLR_KMEM)
+
+With the Kernel memory extension, the Memory Controller is able to limit
+the amount of kernel memory used by the system. Kernel memory is fundamentally
+different than user memory, since it can't be swapped out, which makes it
+possible to DoS the system by consuming too much of this precious resource.
+
+Kernel memory limits are not imposed for the root cgroup. Usage for the root
+cgroup may or may not be accounted.
+
+Currently no soft limit is implemented for kernel memory. It is future work
+to trigger slab reclaim when those limits are reached.
+
+2.7.1 Current Kernel Memory resources accounted
+
+* sockets memory pressure: some sockets protocols have memory pressure
+thresholds. The Memory Controller allows them to be controlled individually
+per cgroup, instead of globally.
+
+* tcp memory pressure: sockets memory pressure for the tcp protocol.
+
 3. User Interface
 
 0. Configuration

Documentation/cgroups/net_prio.txt

@@ -0,0 +1,53 @@
+Network priority cgroup
+-------------------------
+
+The Network priority cgroup provides an interface to allow an administrator to
+dynamically set the priority of network traffic generated by various
+applications
+
+Nominally, an application would set the priority of its traffic via the
+SO_PRIORITY socket option.  This however, is not always possible because:
+
+1) The application may not have been coded to set this value
+2) The priority of application traffic is often a site-specific administrative
+   decision rather than an application defined one.
+
+This cgroup allows an administrator to assign a process to a group which defines
+the priority of egress traffic on a given interface. Network priority groups can
+be created by first mounting the cgroup filesystem.
+
+# mount -t cgroup -onet_prio none /sys/fs/cgroup/net_prio
+
+With the above step, the initial group acting as the parent accounting group
+becomes visible at '/sys/fs/cgroup/net_prio'.  This group includes all tasks in
+the system. '/sys/fs/cgroup/net_prio/tasks' lists the tasks in this cgroup.
+
+Each net_prio cgroup contains two files that are subsystem specific
+
+net_prio.prioidx
+This file is read-only, and is simply informative.  It contains a unique integer
+value that the kernel uses as an internal representation of this cgroup.
+
+net_prio.ifpriomap
+This file contains a map of the priorities assigned to traffic originating from
+processes in this group and egressing the system on various interfaces. It
+contains a list of tuples in the form <ifname priority>.  Contents of this file
+can be modified by echoing a string into the file using the same tuple format.
+for example:
+
+echo "eth0 5" > /sys/fs/cgroups/net_prio/iscsi/net_prio.ifpriomap
+
+This command would force any traffic originating from processes belonging to the
+iscsi net_prio cgroup and egressing on interface eth0 to have the priority of
+said traffic set to the value 5. The parent accounting group also has a
+writeable 'net_prio.ifpriomap' file that can be used to set a system default
+priority.
+
+Priorities are set immediately prior to queueing a frame to the device
+queueing discipline (qdisc) so priorities will be assigned prior to the hardware
+queue selection being made.
+
+One usage for the net_prio cgroup is with mqprio qdisc allowing application
+traffic to be steered to hardware/driver based traffic classes. These mappings
+can then be managed by administrators or other networking protocols such as
+DCBX.

Documentation/devicetree/bindings/net/calxeda-xgmac.txt

@@ -0,0 +1,15 @@
+* Calxeda Highbank 10Gb XGMAC Ethernet
+
+Required properties:
+- compatible : Should be "calxeda,hb-xgmac"
+- reg : Address and length of the register set for the device
+- interrupts : Should contain 3 xgmac interrupts. The 1st is main interrupt.
+  The 2nd is pwr mgt interrupt. The 3rd is low power state interrupt.
+
+Example:
+
+ethernet@fff50000 {
+        compatible = "calxeda,hb-xgmac";
+        reg = <0xfff50000 0x1000>;
+        interrupts = <0 77 4  0 78 4  0 79 4>;
+};

Documentation/devicetree/bindings/net/can/cc770.txt

@@ -0,0 +1,53 @@
+Memory mapped Bosch CC770 and Intel AN82527 CAN controller
+
+Note: The CC770 is a CAN controller from Bosch, which is 100%
+compatible with the old AN82527 from Intel, but with "bugs" being fixed.
+
+Required properties:
+
+- compatible : should be "bosch,cc770" for the CC770 and "intc,82527"
+	for the AN82527.
+
+- reg : should specify the chip select, address offset and size required
+	to map the registers of the controller. The size is usually 0x80.
+
+- interrupts : property with a value describing the interrupt source
+	(number and sensitivity) required for the controller.
+
+Optional properties:
+
+- bosch,external-clock-frequency : frequency of the external oscillator
+	clock in Hz. Note that the internal clock frequency used by the
+	controller is half of that value. If not specified, a default
+	value of 16000000 (16 MHz) is used.
+
+- bosch,clock-out-frequency : slock frequency in Hz on the CLKOUT pin.
+	If not specified or if the specified value is 0, the CLKOUT pin
+	will be disabled.
+
+- bosch,slew-rate : slew rate of the CLKOUT signal. If not specified,
+	a resonable value will be calculated.
+
+- bosch,disconnect-rx0-input : see data sheet.
+
+- bosch,disconnect-rx1-input : see data sheet.
+
+- bosch,disconnect-tx1-output : see data sheet.
+
+- bosch,polarity-dominant : see data sheet.
+
+- bosch,divide-memory-clock : see data sheet.
+
+- bosch,iso-low-speed-mux : see data sheet.
+
+For further information, please have a look to the CC770 or AN82527.
+
+Examples:
+
+can@3,100 {
+	compatible = "bosch,cc770";
+	reg = <3 0x100 0x80>;
+	interrupts = <2 0>;
+	interrupt-parent = <&mpic>;
+	bosch,external-clock-frequency = <16000000>;
+};

Documentation/feature-removal-schedule.txt

@@ -263,8 +263,7 @@ Who:	Ravikiran Thirumalai <kiran@scalex86.org>
 
 What:	Code that is now under CONFIG_WIRELESS_EXT_SYSFS
 	(in net/core/net-sysfs.c)
-When:	After the only user (hal) has seen a release with the patches
-	for enough time, probably some time in 2010.
+When:	3.5
 Why:	Over 1K .text/.data size reduction, data is available in other
 	ways (ioctls)
 Who:	Johannes Berg <johannes@sipsolutions.net>

Documentation/networking/00-INDEX

@@ -144,6 +144,8 @@ nfc.txt
 	- The Linux Near Field Communication (NFS) subsystem.
 olympic.txt
 	- IBM PCI Pit/Pit-Phy/Olympic Token Ring driver info.
+openvswitch.txt
+	- Open vSwitch developer documentation.
 operstates.txt
 	- Overview of network interface operational states.
 packet_mmap.txt

Documentation/networking/batman-adv.txt

@@ -200,15 +200,16 @@ abled  during run time. Following log_levels are defined:
 
 0 - All  debug  output  disabled
 1 - Enable messages related to routing / flooding / broadcasting
-2 - Enable route or tt entry added / changed / deleted
-3 - Enable all messages
+2 - Enable messages related to route added / changed / deleted
+4 - Enable messages related to translation table operations
+7 - Enable all messages
 
 The debug output can be changed at runtime  using  the  file
 /sys/class/net/bat0/mesh/log_level. e.g.
 
 # echo 2 > /sys/class/net/bat0/mesh/log_level
 
-will enable debug messages for when routes or TTs change.
+will enable debug messages for when routes change.
 
 
 BATCTL

Documentation/networking/bonding.txt

@@ -196,6 +196,23 @@ or, for backwards compatibility, the option value.  E.g.,
 
 	The parameters are as follows:
 
+active_slave
+
+	Specifies the new active slave for modes that support it
+	(active-backup, balance-alb and balance-tlb).  Possible values
+	are the name of any currently enslaved interface, or an empty
+	string.  If a name is given, the slave and its link must be up in order
+	to be selected as the new active slave.  If an empty string is
+	specified, the current active slave is cleared, and a new active
+	slave is selected automatically.
+
+	Note that this is only available through the sysfs interface. No module
+	parameter by this name exists.
+
+	The normal value of this option is the name of the currently
+	active slave, or the empty string if there is no active slave or
+	the current mode does not use an active slave.
+
 ad_select
 
 	Specifies the 802.3ad aggregation selection logic to use.  The

Documentation/networking/ieee802154.txt

@@ -78,3 +78,30 @@ in software. This is currently WIP.
 
 See header include/net/mac802154.h and several drivers in drivers/ieee802154/.
 
+6LoWPAN Linux implementation
+============================
+
+The IEEE 802.15.4 standard specifies an MTU of 128 bytes, yielding about 80
+octets of actual MAC payload once security is turned on, on a wireless link
+with a link throughput of 250 kbps or less.  The 6LoWPAN adaptation format
+[RFC4944] was specified to carry IPv6 datagrams over such constrained links,
+taking into account limited bandwidth, memory, or energy resources that are
+expected in applications such as wireless Sensor Networks.  [RFC4944] defines
+a Mesh Addressing header to support sub-IP forwarding, a Fragmentation header
+to support the IPv6 minimum MTU requirement [RFC2460], and stateless header
+compression for IPv6 datagrams (LOWPAN_HC1 and LOWPAN_HC2) to reduce the
+relatively large IPv6 and UDP headers down to (in the best case) several bytes.
+
+In Semptember 2011 the standard update was published - [RFC6282].
+It deprecates HC1 and HC2 compression and defines IPHC encoding format which is
+used in this Linux implementation.
+
+All the code related to 6lowpan you may find in files: net/ieee802154/6lowpan.*
+
+To setup 6lowpan interface you need (busybox release > 1.17.0):
+1. Add IEEE802.15.4 interface and initialize PANid;
+2. Add 6lowpan interface by command like:
+   # ip link add link wpan0 name lowpan0 type lowpan
+3. Set MAC (if needs):
+   # ip link set lowpan0 address de:ad:be:ef:ca:fe:ba:be
+4. Bring up 'lowpan0' interface

Documentation/networking/ifenslave.c

@@ -539,12 +539,14 @@ static int if_getconfig(char *ifname)
 		metric = 0;
 	} else
 		metric = ifr.ifr_metric;
+	printf("The result of SIOCGIFMETRIC is %d\n", metric);
 
 	strcpy(ifr.ifr_name, ifname);
 	if (ioctl(skfd, SIOCGIFMTU, &ifr) < 0)
 		mtu = 0;
 	else
 		mtu = ifr.ifr_mtu;
+	printf("The result of SIOCGIFMTU is %d\n", mtu);
 
 	strcpy(ifr.ifr_name, ifname);
 	if (ioctl(skfd, SIOCGIFDSTADDR, &ifr) < 0) {

Documentation/networking/ip-sysctl.txt

@@ -31,6 +31,16 @@ neigh/default/gc_thresh3 - INTEGER
 	when using large numbers of interfaces and when communicating
 	with large numbers of directly-connected peers.
 
+neigh/default/unres_qlen_bytes - INTEGER
+	The maximum number of bytes which may be used by packets
+	queued for each	unresolved address by other network layers.
+	(added in linux 3.3)
+
+neigh/default/unres_qlen - INTEGER
+	The maximum number of packets which may be queued for each
+	unresolved address by other network layers.
+	(deprecated in linux 3.3) : use unres_qlen_bytes instead.
+
 mtu_expires - INTEGER
 	Time, in seconds, that cached PMTU information is kept.
 
@@ -165,6 +175,9 @@ tcp_congestion_control - STRING
 	connections. The algorithm "reno" is always available, but
 	additional choices may be available based on kernel configuration.
 	Default is set as part of kernel configuration.
+	For passive connections, the listener congestion control choice
+	is inherited.
+	[see setsockopt(listenfd, SOL_TCP, TCP_CONGESTION, "name" ...) ]
 
 tcp_cookie_size - INTEGER
 	Default size of TCP Cookie Transactions (TCPCT) option, that may be