---

yaml
---
r: 335798
b: refs/heads/master
c: 0cad3ff
h: refs/heads/master
v: v3

[refs]

@@ -1,2 +1,2 @@
 ---
-refs/heads/master: 5576646f3c1abd60d72d19829de6f5d8c2ca8ecf
+refs/heads/master: 0cad3ff40486e341715cac3b5ef7b135fa0ba316

trunk/Documentation/filesystems/proc.txt

@@ -33,7 +33,7 @@ Table of Contents
   2	Modifying System Parameters
 
   3	Per-Process Parameters
-  3.1	/proc/<pid>/oom_score_adj - Adjust the oom-killer
+  3.1	/proc/<pid>/oom_adj & /proc/<pid>/oom_score_adj - Adjust the oom-killer
 								score
   3.2	/proc/<pid>/oom_score - Display current oom-killer score
   3.3	/proc/<pid>/io - Display the IO accounting fields
@@ -1320,10 +1320,10 @@ of the kernel.
 CHAPTER 3: PER-PROCESS PARAMETERS
 ------------------------------------------------------------------------------
 
-3.1 /proc/<pid>/oom_score_adj- Adjust the oom-killer score
+3.1 /proc/<pid>/oom_adj & /proc/<pid>/oom_score_adj- Adjust the oom-killer score
 --------------------------------------------------------------------------------
 
-This file can be used to adjust the badness heuristic used to select which
+These file can be used to adjust the badness heuristic used to select which
 process gets killed in out of memory conditions.
 
 The badness heuristic assigns a value to each candidate task ranging from 0
@@ -1361,6 +1361,12 @@ same system, cpuset, mempolicy, or memory controller resources to use at least
 equivalent to discounting 50% of the task's allowed memory from being considered
 as scoring against the task.
 
+For backwards compatibility with previous kernels, /proc/<pid>/oom_adj may also
+be used to tune the badness score.  Its acceptable values range from -16
+(OOM_ADJUST_MIN) to +15 (OOM_ADJUST_MAX) and a special value of -17
+(OOM_DISABLE) to disable oom killing entirely for that task.  Its value is
+scaled linearly with /proc/<pid>/oom_score_adj.
+
 The value of /proc/<pid>/oom_score_adj may be reduced no lower than the last
 value set by a CAP_SYS_RESOURCE process. To reduce the value any lower
 requires CAP_SYS_RESOURCE.
@@ -1375,7 +1381,9 @@ minimal amount of work.
 -------------------------------------------------------------
 
 This file can be used to check the current score used by the oom-killer is for
-any given <pid>.
+any given <pid>. Use it together with /proc/<pid>/oom_score_adj to tune which
+process should be killed in an out-of-memory situation.
+
 
 3.3  /proc/<pid>/io - Display the IO accounting fields
 -------------------------------------------------------

trunk/Documentation/networking/netdev-features.txt

@@ -164,4 +164,4 @@ read the CRC recorded by the NIC on receipt of the packet.
 This requests that the NIC receive all possible frames, including errored
 frames (such as bad FCS, etc).  This can be helpful when sniffing a link with
 bad packets on it.  Some NICs may receive more packets if also put into normal
-PROMISC mdoe.
+PROMISC mode.

trunk/MAINTAINERS

@@ -7259,6 +7259,14 @@ L:	linux-xtensa@linux-xtensa.org
 S:	Maintained
 F:	arch/xtensa/
 
+THERMAL
+M:      Zhang Rui <rui.zhang@intel.com>
+L:      linux-pm@vger.kernel.org
+T:      git git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux.git
+S:      Supported
+F:      drivers/thermal/
+F:      include/linux/thermal.h
+
 THINKPAD ACPI EXTRAS DRIVER
 M:	Henrique de Moraes Holschuh <ibm-acpi@hmh.eng.br>
 L:	ibm-acpi-devel@lists.sourceforge.net

trunk/arch/arm/boot/Makefile

@@ -33,7 +33,7 @@ ifeq ($(CONFIG_XIP_KERNEL),y)
 
 $(obj)/xipImage: vmlinux FORCE
 	$(call if_changed,objcopy)
-	$(kecho) '  Kernel: $@ is ready (physical address: $(CONFIG_XIP_PHYS_ADDR))'
+	@$(kecho) '  Kernel: $@ is ready (physical address: $(CONFIG_XIP_PHYS_ADDR))'
 
 $(obj)/Image $(obj)/zImage: FORCE
 	@echo 'Kernel configured for XIP (CONFIG_XIP_KERNEL=y)'
@@ -48,14 +48,14 @@ $(obj)/xipImage: FORCE
 
 $(obj)/Image: vmlinux FORCE
 	$(call if_changed,objcopy)
-	$(kecho) '  Kernel: $@ is ready'
+	@$(kecho) '  Kernel: $@ is ready'
 
 $(obj)/compressed/vmlinux: $(obj)/Image FORCE
 	$(Q)$(MAKE) $(build)=$(obj)/compressed $@
 
 $(obj)/zImage:	$(obj)/compressed/vmlinux FORCE
 	$(call if_changed,objcopy)
-	$(kecho) '  Kernel: $@ is ready'
+	@$(kecho) '  Kernel: $@ is ready'
 
 endif
 
@@ -90,15 +90,15 @@ fi
 $(obj)/uImage:	$(obj)/zImage FORCE
 	@$(check_for_multiple_loadaddr)
 	$(call if_changed,uimage)
-	$(kecho) '  Image $@ is ready'
+	@$(kecho) '  Image $@ is ready'
 
 $(obj)/bootp/bootp: $(obj)/zImage initrd FORCE
 	$(Q)$(MAKE) $(build)=$(obj)/bootp $@
 	@:
 
 $(obj)/bootpImage: $(obj)/bootp/bootp FORCE
 	$(call if_changed,objcopy)
-	$(kecho) '  Kernel: $@ is ready'
+	@$(kecho) '  Kernel: $@ is ready'
 
 PHONY += initrd FORCE
 initrd:

trunk/arch/arm/boot/dts/tegra30.dtsi

@@ -73,8 +73,8 @@
 
 	pinmux: pinmux {
 		compatible = "nvidia,tegra30-pinmux";
-		reg = <0x70000868 0xd0    /* Pad control registers */
-		       0x70003000 0x3e0>; /* Mux registers */
+		reg = <0x70000868 0xd4    /* Pad control registers */
+		       0x70003000 0x3e4>; /* Mux registers */
 	};
 
 	serial@70006000 {

trunk/arch/arm/mach-at91/at91rm9200_devices.c

@@ -68,7 +68,7 @@ void __init at91_add_device_usbh(struct at91_usbh_data *data)
 
 	/* Enable overcurrent notification */
 	for (i = 0; i < data->ports; i++) {
-		if (data->overcurrent_pin[i])
+		if (gpio_is_valid(data->overcurrent_pin[i]))
 			at91_set_gpio_input(data->overcurrent_pin[i], 1);
 	}
 

trunk/arch/arm/mach-at91/at91sam9260_devices.c

@@ -72,7 +72,7 @@ void __init at91_add_device_usbh(struct at91_usbh_data *data)
 
 	/* Enable overcurrent notification */
 	for (i = 0; i < data->ports; i++) {
-		if (data->overcurrent_pin[i])
+		if (gpio_is_valid(data->overcurrent_pin[i]))
 			at91_set_gpio_input(data->overcurrent_pin[i], 1);
 	}
 

trunk/arch/arm/mach-at91/at91sam9261_devices.c

@@ -72,7 +72,7 @@ void __init at91_add_device_usbh(struct at91_usbh_data *data)
 
 	/* Enable overcurrent notification */
 	for (i = 0; i < data->ports; i++) {
-		if (data->overcurrent_pin[i])
+		if (gpio_is_valid(data->overcurrent_pin[i]))
 			at91_set_gpio_input(data->overcurrent_pin[i], 1);
 	}
 

trunk/arch/arm/mach-at91/at91sam9263_devices.c

@@ -78,7 +78,7 @@ void __init at91_add_device_usbh(struct at91_usbh_data *data)
 
 	/* Enable overcurrent notification */
 	for (i = 0; i < data->ports; i++) {
-		if (data->overcurrent_pin[i])
+		if (gpio_is_valid(data->overcurrent_pin[i]))
 			at91_set_gpio_input(data->overcurrent_pin[i], 1);
 	}
 

trunk/arch/arm/mach-at91/at91sam9g45_devices.c

@@ -1841,8 +1841,8 @@ static struct resource sha_resources[] = {
 		.flags	= IORESOURCE_MEM,
 	},
 	[1] = {
-		.start	= AT91SAM9G45_ID_AESTDESSHA,
-		.end	= AT91SAM9G45_ID_AESTDESSHA,
+		.start	= NR_IRQS_LEGACY + AT91SAM9G45_ID_AESTDESSHA,
+		.end	= NR_IRQS_LEGACY + AT91SAM9G45_ID_AESTDESSHA,
 		.flags	= IORESOURCE_IRQ,
 	},
 };
@@ -1874,8 +1874,8 @@ static struct resource tdes_resources[] = {
 		.flags	= IORESOURCE_MEM,
 	},
 	[1] = {
-		.start	= AT91SAM9G45_ID_AESTDESSHA,
-		.end	= AT91SAM9G45_ID_AESTDESSHA,
+		.start	= NR_IRQS_LEGACY + AT91SAM9G45_ID_AESTDESSHA,
+		.end	= NR_IRQS_LEGACY + AT91SAM9G45_ID_AESTDESSHA,
 		.flags	= IORESOURCE_IRQ,
 	},
 };
@@ -1910,8 +1910,8 @@ static struct resource aes_resources[] = {
 		.flags	= IORESOURCE_MEM,
 	},
 	[1] = {
-		.start	= AT91SAM9G45_ID_AESTDESSHA,
-		.end	= AT91SAM9G45_ID_AESTDESSHA,
+		.start	= NR_IRQS_LEGACY + AT91SAM9G45_ID_AESTDESSHA,
+		.end	= NR_IRQS_LEGACY + AT91SAM9G45_ID_AESTDESSHA,
 		.flags	= IORESOURCE_IRQ,
 	},
 };

trunk/arch/arm/mach-highbank/system.c

@@ -28,6 +28,7 @@ void highbank_restart(char mode, const char *cmd)
 		hignbank_set_pwr_soft_reset();
 
 	scu_power_mode(scu_base_addr, SCU_PM_POWEROFF);
-	cpu_do_idle();
+	while (1)
+		cpu_do_idle();
 }
 

trunk/arch/arm/mach-imx/clk-gate2.c

@@ -112,7 +112,7 @@ struct clk *clk_register_gate2(struct device *dev, const char *name,
 
 	clk = clk_register(dev, &gate->hw);
 	if (IS_ERR(clk))
-		kfree(clk);
+		kfree(gate);
 
 	return clk;
 }

trunk/arch/arm/mach-imx/ehci-imx25.c

@@ -30,7 +30,7 @@
 #define MX25_H1_SIC_SHIFT	21
 #define MX25_H1_SIC_MASK	(0x3 << MX25_H1_SIC_SHIFT)
 #define MX25_H1_PP_BIT		(1 << 18)
-#define MX25_H1_PM_BIT		(1 << 8)
+#define MX25_H1_PM_BIT		(1 << 16)
 #define MX25_H1_IPPUE_UP_BIT	(1 << 7)
 #define MX25_H1_IPPUE_DOWN_BIT	(1 << 6)
 #define MX25_H1_TLL_BIT		(1 << 5)

trunk/arch/arm/mach-imx/ehci-imx35.c

@@ -30,7 +30,7 @@
 #define MX35_H1_SIC_SHIFT	21
 #define MX35_H1_SIC_MASK	(0x3 << MX35_H1_SIC_SHIFT)
 #define MX35_H1_PP_BIT		(1 << 18)
-#define MX35_H1_PM_BIT		(1 << 8)
+#define MX35_H1_PM_BIT		(1 << 16)
 #define MX35_H1_IPPUE_UP_BIT	(1 << 7)
 #define MX35_H1_IPPUE_DOWN_BIT	(1 << 6)
 #define MX35_H1_TLL_BIT		(1 << 5)

trunk/arch/arm/mach-omap2/clockdomains44xx_data.c

@@ -359,7 +359,7 @@ static struct clockdomain iss_44xx_clkdm = {
 	.clkdm_offs	  = OMAP4430_CM2_CAM_CAM_CDOFFS,
 	.wkdep_srcs	  = iss_wkup_sleep_deps,
 	.sleepdep_srcs	  = iss_wkup_sleep_deps,
-	.flags		  = CLKDM_CAN_HWSUP_SWSUP,
+	.flags		  = CLKDM_CAN_SWSUP,
 };
 
 static struct clockdomain l3_dss_44xx_clkdm = {

trunk/arch/arm/mach-omap2/devices.c

@@ -19,6 +19,7 @@
 #include <linux/of.h>
 #include <linux/pinctrl/machine.h>
 #include <linux/platform_data/omap4-keypad.h>
+#include <linux/platform_data/omap_ocp2scp.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/map.h>
@@ -613,6 +614,83 @@ static void omap_init_vout(void)
 static inline void omap_init_vout(void) {}
 #endif
 
+#if defined(CONFIG_OMAP_OCP2SCP) || defined(CONFIG_OMAP_OCP2SCP_MODULE)
+static int count_ocp2scp_devices(struct omap_ocp2scp_dev *ocp2scp_dev)
+{
+	int cnt	= 0;
+
+	while (ocp2scp_dev->drv_name != NULL) {
+		cnt++;
+		ocp2scp_dev++;
+	}
+
+	return cnt;
+}
+
+static void omap_init_ocp2scp(void)
+{
+	struct omap_hwmod	*oh;
+	struct platform_device	*pdev;
+	int			bus_id = -1, dev_cnt = 0, i;
+	struct omap_ocp2scp_dev	*ocp2scp_dev;
+	const char		*oh_name, *name;
+	struct omap_ocp2scp_platform_data *pdata;
+
+	if (!cpu_is_omap44xx())
+		return;
+
+	oh_name = "ocp2scp_usb_phy";
+	name	= "omap-ocp2scp";
+
+	oh = omap_hwmod_lookup(oh_name);
+	if (!oh) {
+		pr_err("%s: could not find omap_hwmod for %s\n", __func__,
+								oh_name);
+		return;
+	}
+
+	pdata = kzalloc(sizeof(*pdata), GFP_KERNEL);
+	if (!pdata) {
+		pr_err("%s: No memory for ocp2scp pdata\n", __func__);
+		return;
+	}
+
+	ocp2scp_dev = oh->dev_attr;
+	dev_cnt = count_ocp2scp_devices(ocp2scp_dev);
+
+	if (!dev_cnt) {
+		pr_err("%s: No devices connected to ocp2scp\n", __func__);
+		kfree(pdata);
+		return;
+	}
+
+	pdata->devices = kzalloc(sizeof(struct omap_ocp2scp_dev *)
+					* dev_cnt, GFP_KERNEL);
+	if (!pdata->devices) {
+		pr_err("%s: No memory for ocp2scp pdata devices\n", __func__);
+		kfree(pdata);
+		return;
+	}
+
+	for (i = 0; i < dev_cnt; i++, ocp2scp_dev++)
+		pdata->devices[i] = ocp2scp_dev;
+
+	pdata->dev_cnt	= dev_cnt;
+
+	pdev = omap_device_build(name, bus_id, oh, pdata, sizeof(*pdata), NULL,
+								0, false);
+	if (IS_ERR(pdev)) {
+		pr_err("Could not build omap_device for %s %s\n",
+						name, oh_name);
+		kfree(pdata->devices);
+		kfree(pdata);
+		return;
+	}
+}
+#else
+static inline void omap_init_ocp2scp(void) { }
+#endif
+
 /*-------------------------------------------------------------------------*/
 
 static int __init omap2_init_devices(void)
@@ -640,6 +718,7 @@ static int __init omap2_init_devices(void)
 	omap_init_sham();
 	omap_init_aes();
 	omap_init_vout();
+	omap_init_ocp2scp();
 
 	return 0;
 }